Encore electronic ENL832-TX-EN, ENL832-TX-RENT, ENL832-TX-RE, ENL832-TX-ICNT User Manual

ENL832-TX-RE & ENL832-TX-RENT

ENL832-TX-EN

& ENL832-TX-ICNT

10/100Mbps Fast Ethernet LAN Card

User's Guide

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits of a Class B
computing devices, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
If you suspect this product is causing interference, turn your computer on and off while
your radio or TV is showing interference. If the interference disappears then when you
turn the computer off and reappears then you turn the computer on, something in the
computer is causing interference.

Features & Specifications

Features & Benefits:

* Supports 32-bit PCI Bus Master for high performance and low processor utilization.
* Complies to PCI 2.1 and PCI 2.2 specification
* Complies with the IEEE 802.3 CSMA/CD, 10/100Base-TX standard.
* Full duplex design to double the performance to 20Mbps/200Mbps.
* One STP connector for 100Mbps or 10Mbps network speed.
* Support Auto-negotiation function.
* Built-in FIFO buffers to eliminate external memory.
* Auto-setups IRQ and I/O address.
* Supports early interrupt on transmit to increase performance.
* Supports Novell NetWare, Windows NT/98/ME/2000/XP and other popular

operating systems

* Provides diagnostic software
* Wake on LAN (If adapter supports WOL function).
* Topology : Star
* Connect to : RJ-45

1

Standard & Specification:

* Standard: IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX
* Transmission Rate: 10Mbps or 100Mbps
* Hardware Required: IBM compatible PC with available PCI slot ( PCI 2.1 or PCI 2.2 )
* IRQ Line: Assigned by system
* I/O Address : Assigned by system
* Drivers: Novell NetWare, Windows NT/98/ME/2000/XP and other popular operating

systems
* Temperature : 0 to 55 C (Operating)
* Humidity : 10% to 90% (Non-condensing)
* Power consumption : 1.8W (Max.)

Trouble-shooting

If you experience any problems with the adapter, first make sure the appropriate
driver is loaded, the proper cable is connected to the adapter port and the hub
complies with the adapter specification, such as 10Mbps 10Base-TX or 100Mbps
100BaseTX, then check the LED.

TRADEMARKS

Copyright 2000 by the manufacturer of this product. No part of this manual may be
reproduced, transcribed, stored in a retrieval system, translated into any language or
computer language or computer language without the prior written consent of the
manufacturer. All brand and product names are trademarks and/or registered
trademarks of their respective companies.

Hardware Installation:

1. Turn off the computer and remove its cover.

2. Insert the adapter into a PCI slot.

3. Secure this adapter to the rear of the computer chassis and put back the

computer cover.

4. Connect the adapter to the network using twisted-pair cable.

5. Connect the NIC and the PC mother board with WOL cable. (If adapter supports WOL
function)

2

Driver Installation:

[For ENL832-TX-RE & ENL832_TX_RENT]

1. For Windows XP, Windows 2000 and Windows Me:

a) When Windows boots up, operating system will detect the LAN card and

Found New Hardware Wizard windows will appear. Click Cancel

b) Insert the Driver Installation CD into CD-ROM drive, window below will appear

then click Install Driver:

c) When OS finishes loading device driver, window below will appear. Click Ok

to complete the installation:

3

2. For Windows 98SE:

a) When system boots up, operating system will automatically detect the LAN

card and Add New Hardware Wizard window will appear, and then click
Cancel:

b) Insert the Driver Installation CD into CD-ROM drive, window below will appear

then click Install Driver to install device driver.

4