Encore N150, N300 User Manual

© 2010 Encore Electronics, Inc. All rights reserved.COVER
© 2011 Encore Electronics, Inc.
Product specifications, size, and shape are subject to change without notice, and actual product appearance may differ from that depicted herein.
All trademarks and brand names are the properties of their respective holders.
TABLE OF CONTENTS
CHAPTER 1: INTRODUCTION ..................................................................... 4
1.3 F
1.4 B
ACKAGE CONTENTS ................................................................ 4
YSTEM REQUIREMENTS .......................................................... 4
RONT PANEL AND LED INDICATORS ....................................... 5
ACK PANEL AND CONNECTORS .............................................. 6
CHAPTER 2: CONNECTING YOUR ROUTER .......................................... 7
CHAPTER 3: CONFIGURING YOUR ROUTER ........................................ 9
3.1 A
CCESSING THE WEB-BASED CONFIGURATION UTILITY ......... 9
NCORE SETUP WIZARD ......................................................... 11
CHAPTER 4: ADVANCED CONFIGURATION ........................................ 14
4.1 WAN (W
IDE AREA NETWORK) ............................................... 14
4.1.1 Connection Type ................................................................. 14
A. DHCP Client or Fixed IP ................................................................. 15
B. PPPoE ............................................................................................... 16
C. PPTP/L2TP with Dynamic IP (Obtain IP Automatically) ............. 17
D. PPTP/L2TP with Static IP (Specify IP) .......................................... 18
E. BigPond Cable ................................................................................. 19
4.1.2 Dynamic DNS ....................................................................... 20
4.2 W
IRELESS ................................................................................ 21
4.2.1 Basic ...................................................................................... 21
4.2.2 Security ................................................................................. 22
4.2.2.1 WEP .................................................................................................. 23
4.2.2.2 WPA/WPA2/WPA-Auto with EAP ................................................ 24
4.2.2.3 WPA/WPA2/WPA2-Auto Security with PSK ............................. 25
4.2.3 Advanced .............................................................................. 26
1
www.encore-usa.com
DTIM Interval: Type a DTIM (Delivery Traffic Indication Message)
interval in the text box. ................................................................................ 26
4.2.4 Wi-Fi Protected Setup ........................................................ 27
This screen enables users to configure the Wi-Fi Protected Setup
(WPS) function. ............................................................................................ 27
4.3 LAN ......................................................................................... 28
4.3.1 Basic ...................................................................................... 28
4.3.2 DHCP ...................................................................................... 29
4.4 R
OUTING .................................................................................. 30
4.4.1 Static ...................................................................................... 30
4.4.2 Dynamic ................................................................................ 31
4.4.3 Routing Table ....................................................................... 31
4.5 A
CCESS CONTROL .................................................................. 32
4.5.1 Filters ..................................................................................... 32
4.5.1.1 MAC Filters ..................................................................................... 33
4.5.1.2 IP Filter ............................................................................................. 34
4.5.1.3 URL/Domain Blocking .................................................................. 35
4.5.1.4 Protocol Filters .............................................................................. 36
4.5.2 Virtual Server ....................................................................... 37
4.5.3 Special AP ............................................................................. 38
4.5.4 DMZ ........................................................................................ 39
4.5.5 Firewall Rule ........................................................................ 40
YSTEM ................................................................................... 42
4.6.1 Password .............................................................................. 42
4.6.2 Time ........................................................................................ 43
4.6.3 Device Information ............................................................. 44
4.6.4 Log .......................................................................................... 45
4.6.5 Log Setting ........................................................................... 46
www.encore-usa.com
2
4.6.6 Statistic .................................................................................. 48
4.6.7 Restart ................................................................................... 49
4.6.8 Firmware ............................................................................... 50
4.6.9 Configuration ....................................................................... 51
4.6.10 UPnP ...................................................................................... 52
4.6.11 Ping Test ............................................................................... 53
4.6.12 Remote Management ......................................................... 54
CHAPTER 5: CONFIGURE THE DEVICE AS AN ACCESS POINT .... 55
APPENDIX A. REGULATORY INFORMATION ......................................... 57
A1. F
EDERAL COMMUNICATION COMMISSION INTERFERENCE
STATEMENT 57
A2. E
UROPE –EUDECLARATION OF CONFORMITY ...................... 58
APPENDIX B. SOFTWARE END USER LICENSE AGREEMENT ........ 61
APPENDIX C. USER’S NOTICE .................................................................. 63
Product specifications, size, and shape are subject to change without notice, and actual
product appearance may differ from that depicted herein.
All trademarks and brand names are the properties of their respective holders.
© 2011 Encore Electronics, Inc. All rights reserved.
www.encore-usa.com
3
Chapter 1: Introduction
The ENHWI-1AN4x Wireless N150 Router / ENHWI-2AN4x Wireless N300 Router complies with IEEE 802.11n, and provides faster and farther range than 802.11g while being backward compatible with 802.11g and 802.11b mode. This router uses advanced broadband router chipset and wireless LAN chipset solution to let you enjoy high-speed Wired and Wireless connection. Simply connect this device to a Cable or DSL modem and then you can share your high-speed Internet access with multiple PCs at your home with or without wires. It creates a secure Wired and Wireless network for you to share photos, files, video, music, printer and network storage. ENHWI-1AN4x / ENHWI-2AN4x provides maximum transfer rate up to 150Mbps and supports WEP, WPA, WPA2, 802.1x high-level WLAN security features that guarantee the best security for users.
1.1 Package Contents
x Γ Wireless N300 Router or Wireless N150 Router x1 x Γ External Antenna x2 (for the N300 Series)
X1 (for the N150 Series)
x Γ External Power Adapter x1 x Γ Setup CD (User Manual in the CD) x1 x Γ RJ-45 Ethernet Cable x1
1.2 System Requirements
x Γ Active broadband connection with cable/DSL modem x Γ 10/100 Ethernet cables with RJ-45 connector x Γ Ethernet or wireless enabled computers x Γ TCP/IP protocol must be installed on the connecting computers x Γ Web browser: Internet Explorer 7 or later, or Mozilla Firefox 3 or later
www.encore-usa.com
4
1.3 Front Panel and LED Indicators
LED Status Description
POWER
SYSTEM
WAN
WLAN
LAN
(1/2/3/4)
WPS
On The router power is on.
Off The router power is off.
On The router is starting the system.
Slow Blinking The router system is ready to work.
On WAN port is successfully connected
The router is sending or receiving data
Blinking
Slow Blinking Wireless network is ready.
Blinking
On LAN port is successfully connected.
Blinking
On
Off The WPS PBC/PIN function is not running.
Slow Blinking
through the WAN (usually is your cable/DSL modem).
The router is sending or receiving data over the wireless network.
The router is sending or receiving data over the wired network.
The WPS LED keeps on for around 8 seconds while the system is starting.
The WPS PBC function is running and last for 2 minutes after pressing and holding the WPS button for 3 or more seconds.
www.encore-usa.com
5
1.4 Back Panel and Connectors
Port / Button Description
Attach the external antenna(s) with R-SMA connector here.
Antenna
Reset
LAN
(1/2/3/4)
WAN
POWER
(The N300 Series has two antenna connectors, while the N150 Series only has one.) The Reset button will restore your router to the default setting. Press and hold the button for 6 seconds to enable the reset function.
Note: Before using the reset button, you should try two things:
1. Disconnect and power off both your modem and router. Wait for 30 seconds and turn on your modem FIRST. Wait for another 60 seconds for your modem to boot up. LAST, connect the modem back to the router and turn on the router. Wait for another 60 seconds for the router to boot up. RESTART your web browser to see if you can access the Internet now.
2. If the first solution does not work, restart your computer and open your web browser again.
If the above-mentioned two solutions and the reset function cannot solve your problem, contact your Internet service provider to see if there is a problem with you modem or Internet service.
Connect the 10/100 Ethernet Cable with RJ-45 connector here.
Most networking devices should connect to the LAN port, such as computer, NAS, IP camera, print server, switch, and access point.
Connect the 10/100 Ethernet Cable with RJ-45 connector here.
Only connect a Wide Area Network (WAN) device to this port, such as a Cable/DSL modem.
Connect the bundled DC 12V power adapter here.
www.encore-usa.com
6
Chapter 2: Connecting Your Router
1. Attach the antenna to the back of the router.
2. Power off your Cable/DSL modem.
3. Connect your computer to the LAN port on the router with an Ethernet cable.
4. Connect your Cable/DSL modem to the WAN port on the Router with an Ethernet
cable.
5. Power on the Cable/DSL modem, BEFORE powering on the router. Wait for 60
seconds for your modem to boot up.
6. Plug the bundled power adapter to a power outlet. Connect the power adapter to
the router. Wait for another 60 seconds for your router to boot up.
7
www.encore-usa.com
7. Check the LED lights (see Page 5 for more details).
8. The LAN lights should be on for each active LAN connection.
9. The WAN lights should be on when the Cable/DSL modem is connected.
www.encore-usa.com
8
Chapter 3: Configuring Your Router
3.1 Accessing the Web-Based Configuration Utility
Screenshot of the Web-Based Configuration Utility
For the initial configuration, we recommend you connecting your computer to the LAN port with an Ethernet cable. If this cannot be done, you have to connect to the router wirelessly.
Before configuring your router through wireless network, make sure that SSID, Channel
and Security are set properly. The default setting of the WLAN Router that you will use:
x SSID: default x Channel: 11 x 802.11 Mode: 802.11b/g/n mixed mode x Channel bandwidth: 20/40MHz x Security: Disable
Note:
Before you configure the router, make sure the host PC is set on the IP subnet that can be accessed by your cable/DSL modem. For example, when the default network address of
the cable/DSL modem is 192.168.10.x, then the host PC should be set at 192.168.10.xxx (where xxx is a number between 2 and 254), and the default subnet mask is
255.255.255.0.
9
www.encore-usa.com
You need a web browser to access the web-based configuration utility.
1. Open a web browser.
2. Type in the following URL to the address bar:
http://192.168.10.1
sample screenshot from Internet Explore.
3. The web browser will ask you for User Name and Password. The default access information is as follows:
User Name: admin
Password: admin The login window varies among web browsers. Below is an example from Internet Explore
www.encore-usa.com
10
3.2 Encore Setup Wizard
Encore Setup Wizard helps you to configure the router quickly. Simply follow the
step-by-step instructions
A.
B.
To access the Setup Wizard, click on “Wizard” at the bottom of the function menu.
This is the Setup Wizard overview page.
Click “Next” to continue.
www.encore-usa.com
11
C.
Create your own administrative password for the router in this page.
Click “Next” to continue.
D.
E.
Choose your time zone.
Click “Next” to continue.
Most of the time, you can leave the DHCP ServerEnabled” and skip this page
If your MODEM has router function built-in and enabled, you need to check
Disabled” for DHCP Server.
Click “Next” to continue.
www.encore-usa.com
12
F.
G.
Most of the time, you just need to click “Next” to continue.
The Setup Wizard will attempt to detect your Internet connection type automatically (one of the six options). You can also manually select the connection type.
Based on the connection type, the following pages (not shown here) will request different account information. Just follow the on-screen instructions. For more details, please refer to Chapter 4.1.1:
Connection Type.
Click “Enable” to enable Wireless LAN.
If Wireless is enabled, you need to enter the name of your wireless network in the SSID text box and select a radio channel in the dropdown menu.
Any networking device wishes to connect to your router needs to use the same SSID and channel.
H.
The Setup Wizard is now completed. The new settings will be effective AFTER the router reboots.
Click “Restart” to reboot the router. If you do not want to make any changes, click “Exit.”
13
www.encore-usa.com
Chapter 4: Advanced Configuration
4.1 WAN (Wide Area Network)
This section enables users to set up the Wide Area Network (WAN) connection: specifying the WAN IP address, adding DNS numbers, and entering the MAC address.
4.1.1 Connection Type
There are five connection types to choose:
z DHCP Client or Fixed IP z PPPoE z PPTP z L2TP z BigPond Cable
www.encore-usa.com
14
A. DHCP Client or Fixed IP
If user has the DHCP server enabled, choose "Obtain IP automatically (DHCP client)" to
have the router assign IP addresses automatically.
WAN IP Address Select whether you want the router to “Obtain IP Automatically” or manually input Fixed IP by checking “Specify IP.”
IP Address
Under the “Specify IP” mode, enter the information provided by your ISP.
Subnet Mask
Under the “Specify IP” mode, enter the information provided by your ISP.
Gateway
Under the “Specify IP” mode, enter the information provided by your ISP.
DNS 1/2
Under the “Obtain IP Automatically” mode, the DHCP server will provide DNS server IP automatically if this field is 0.0.0.0. Under the “Specify IP” mode, manually enter the DNS server IP address.
Clone MAC Address
If your ISP requires you to enter a specific MAC address, please enter it here. The “Clone MAC Address” button is used to copy the MAC address of your Ethernet adapter to the
Router.
15
www.encore-usa.com
B. PPPoE
If connecting to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP (Internet Service Provider) will provide a Password and User Name. Choose this option and enter the required information.
WAN IP Address Select whether you want the router to “Obtain IP Automatically” or manually input Fixed IP by checking “Specify IP.”
Server Name
Enter the information provided by your ISP (optional).
User Name
Enter the information provided by your ISP.
Password
Enter the information provided by your ISP.
Retype Password
Enter the password again.
DNS
Under the “Obtain IP Automatically” mode, the DHCP server will provide DNS server IP automatically if this field is 0.0.0.0. Under the “Specify IP” mode, manually enter the DNS server IP address.
Auto-Reconnect Three options are available: Always-on, Manual or Connect-on Demand.
Idle Time Out
Enter the idle time out for “Connect-on Demand,” when no Internet access during the idle time, the PPPoE connection will auto disconnect.
MTU
Enter the specified MTU (Maximum Transmission Unit). The default value is 1492 bytes.
www.encore-usa.com
16
C. PPTP/L2TP with Dynamic IP (Obtain IP Automatically)
If connecting to the Internet using a PPTP/L2TP (Dial-up xDSL) protocol with Dynamic IP, check “Obtain IP Automatically.
You need to enter the following information provided by your ISP: Server IP/Name, PPTP/L2TP Account, and PPTP/L2TP Password.
If your ISP has provided you a DNS IP address, enter it in the “DNS” field. Otherwise, leave it as “0.0.0.0.”
www.encore-usa.com
17
D. PPTP/L2TP with Static IP (Specify IP)
If connected to the Internet using a PPTP/L2TP (Dial-up xDSL) with static IP connection, check “Specify IP.”
You need to enter the following information: IP Address, Subnet Mask, Gateway IP address, DNS IP address, Server IP/Name, PPTP/L2TP Account, and PPTP/L2TP Password.
www.encore-usa.com
18
E. BigPond Cable
If your ISP is Big Pond Cable, the ISP will provide you a User Name, Password, Authentication Server, and Login Server IP (Optional). Choose this option and enter the required information.
www.encore-usa.com
19
Loading...
+ 46 hidden pages