Encore ENVCWI-PTG1 - SOFTWARE GUIDE V1.1 Software User's Manual
ENVCWI-PTG1
Wireless Network (IP) Camera with
PAN & TILT
Software User Guide
Version 1.1
- 1 -
Contents
Introduction.........................................................................2
Installation..........................................................................3
Using UltraView..................................................................6
To launch the program....................................................6
Item features...................................................................7
To add a camera ..........................................................12
To remove a camera.....................................................15
To link to the Web page of the camera.........................15
To record video.............................................................16
To configure the recording settings...............................18
To playback the recorded video....................................20
To set up motion detection options...............................21
Information ...................................................................23
- 2 -
I
NTRODUCTION
This Software User Guide provides detailed instructions on
operating UltraView, a customized software application with a
user-friendly interface allowing you to access and control your
camera(s). You can connect up to 16 cameras to monitor different
places and record events for each camera. With UltraView, you
can also change some basic settings of the camera, such as
schedule profiles and motion detecting. In addition, if your camera
supports advanced features, such as audio or pan/tilt function,
you can use these functions through the control panels of
UltraView.
To use UltraView, you have to install it in your computer. It is
recommended to use a high performance computer if you want to
connect multiple cameras simultaneously. The following provides
the system requirements:
Platform: Microsoft® Windows® 2000/XP/Vista.
Hardware Requirement:
1 camera connected: Intel Pentium III 800MHz; 512MB RAM
2 ~ 4 cameras connected: Intel Pentium 4 1.3GHz; 512MB
RAM
5 ~ 8 cameras connected: Intel Pentium 4 2.4GHz; 1GB RAM
9 ~ 16 cameras connected: Intel Pentium 4 3.4GHz; 2GB
RAM
Resolution: 1024x768 or above
NOTE When you use UltraView to record video clips, store the
recorded files to an exclusive hard disk drive in your
computer to ensure that there will be enough storage
space.
- 3 -
I
NSTALLATION
Firstly, insert the Installation CD-ROM into the CD drive of your
computer to initiate the Auto-Run program. The Auto-Run screen
provides the following buttons:
Quick Guide
Advanced Guide
Software Manual
IPFinder
Install Software
Browse
Exit
To start installing:
1. Click Install Software and then select UltraView. The setup
wizard appears to help you complete the installation step-bystep.
NOTE To use UltraView, you must have Microsoft .NET
Framework 2.0 installed in the computer. The setup wizard
will detect it and, if the program is not installed yet, ask you
to install it during the process of installing UltraView.
- 4 -
2. On the welcome screen, click Next.
3. Click Browse to select the destination location to install the
software; otherwise, leave the default setting and click Next.
- 5 -
4. Click Next again to confirm installation. The setup wizard
starts to install the software and the progress bar indicates
the installation is proceeding.
5. Installation is completed. Click Close.
- 6 -
U
SING
U
LTRAVIEW
To launch the program
This section describes the user interface and operating
instructions of UltraView. To launch the program, click Start >
Programs > UltraView > UltraView, and the main screen will
appear as below:
NOTE Please set the resolution to 1024x768 or above on your
computer while using UltraView; otherwise, the displayed
main screen may be distorted.
- 7 -
Item features
The following describes the function of each item on the main
screen:
CONTROLS Panel
- SETTING: Click to enter the Setting screen of UltraView.
Click again to return to the main screen of UltraView.
- PLAY: Click to play the recorded video file using the media
player on the computer (for example, Windows Media
Player by default).
- LOCK: Click to lock the camera controls. Click again to
resume controls for the camera. If you have set ID and
Password in SETTING > Account, you will be asked to
enter the required information to unlock.
- ALL RECORD: Click to start recording video clips using all
connected cameras. Click again to stop recording and save
the files in the computer. When you connect only one
camera, this button’s function is the same as the RECORD
button.
TIP By default, the ID and Password boxes are “blank.” Click
SETTING > Account to change the ID and password of
lock/unlock function.
Loading...