Encore ENNPOE-I User Manual

Page 1
Gigabit PoE Injector
Page 2
Encore PoE Injector
ENNPOE-I
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B f or ITE, the essential protection requirement of Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company.
Product specifications, size, and s hape are subject to change without notice,
and actual product appearance may differ fr om that depicted herein.
All trademarks and brand names are the proper ties of their respective holders.
© 2013 Encore Electronics, Inc. All rights reserved.
Page 3
Encore PoE Injector
ENNPOE-I
Introduction
Encore’s ENNPOE-I PoE Inj ector is a single -port Power-over-Ethernet (PoE) injector device. The ENNPOE-I is designed for 10/100/1000 Mbps Ethernet network and supply power using a single Ethernet cable. This equipment injects DC power and stream network data using CAT5, C AT5 e and CAT6 Ethernet cable to any PoE compliant devices, increasing flexibility in using a PoE enabled device to a non-PoE Ethernet switch.
Key Features
Complies with IEEE802.3at and IEEE 802.3af  1-port 10/100/1000Mbs (Data) for connection to the passive LAN device  1-port 10/100/1000Mbps (Power/Data) for connection to the PoE-PD devices  Automatic PoE/non-PoE device detection. Power output will be automatically turned off when
a non-PoE device is connected to the “PoE/Data” port to avoid device failure.
Compliant with FCC, CE Class B
Interface Ports
Code Name Indication / Function
1 PoE LED
Indicates if the PoE port is providing power or not
Light is off : The PoE port is not providing power
Steady Green : The PoE port is providing power
2 PWR LED
Indicates power source connection
Steady Green : Power is on
Light is off: Power off or not connected to the power outlet
A PoE/DATA port
Indicates power or data or both are active or not
B DATA port
Indicates data transfer activity, supports 10/100/1000 base Ethernet
C
Power Socket
100-240 VAC Power input
Page 4
Encore PoE Injector
ENNPOE-I
PoE Compliant
Power Device
Connection Diagram
Connect the ENNPOE-I PoE Injector as seen in the diagram below. A PoE compliant power device VOIP phone in this example is added to an existing non-PoE network with a non-PoE Ethernet switch.
1. Use Ethernet CAT 5, CAT 5e or CAT 6 with RJ45 connector to connect devices
2. The “Data” port receives Ethernet data from the non-PoE compliant switch.
3. The “PoE/Data” port divides data and power and injects data and power to the PoE compliant PD device, in this sample diagram a VOIP Phone
Package Contents
1. One ENNPOE-I PoE Injector
2. One Power cord
3. One Quick Installation Guide
4. One Screw package
Notes: Make sure that the package contains all the above items. If any of the listed items are damaged or missing, please contact the store you purchase the ENNPOE-I.
Technical Support
Please visit http://www.encore-usa.com
for tech support and the latest product information and
downloads.
Non-PoE Compliant Switch
ENNPOE-I
AC 100-240V power outlet
To “Data” Port
From “PoE/Data” Port to
PoE compliant PD
Loading...