Encore ENMGS-16+2 User Manual

Page 1
ENMGS-16+2
16-Port 10/100/1000Mbps
Web-Smart Gigabit Ethernet Switch
16 x 10/100/1000 Mbps RJ-45 Ports
User’s Guide
Page 2
FCC Warning
ENMGS-16+2 has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonab le p rotection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.
Page 3
UL Warning
a) Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer's maximum rated ambient temperature (Tmra).
b) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
c) Mechanical Loading- mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
d) Circuit Overloading- Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on over current protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concer n.
e) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
Ver. C1-1.00
Page 4
Page 5
TABLE OF CONTENT
About This Guide.................................................................................1
Purpose ............................................................................................1
Terms/Usage....................................................................................1
Introduction..........................................................................................3
Gigabit Ethernet Technology...........................................................3
Fast Ethernet Technology................................................................4
Switching Technology .....................................................................5
VLAN (Virtual Local Area Network)..............................................6
Features............................................................................................6
Unpacking and Installation ..................................................................9
Unpacking........................................................................................9
Installation .......................................................................................9
Rack Mounting ..............................................................................11
Connecting Network Cable............................................................12
AC Power.......................................................................................12
Identifying External Components ......................................................13
Front Panel.....................................................................................13
Rear Panel......................................................................................14
Understanding LED Indi cat o r s..........................................................15
Power and System LEDs ...............................................................15
1000BASE-T Port 1~16 Status LEDs............................................16
Combo mini-GBIC Port 15~ 16 Status LEDs................................17
Configuration.....................................................................................18
i
Page 6
Installing the Web Management Utility.........................................18
Discovery List................................................................................19
Monitor List...................................................................................20
Device Setting................................................................................22
Toolbar...........................................................................................24
Configuring the Switch..................................................................25
Login..............................................................................................25
Configuration Me nu.......................................................................27
Configuration Setting.....................................................................28
Port Settings...............................................................................28
IEEE 802.1Q VLAN..................................................................30
Trunk Setting .............................................................................40
Mirror Setting.............................................................................41
IEEE 802.1p Default Priority..................................................... 42
Broadcast Storm Control Setting ...............................................43
Jumbo Frame Setting .................................................................43
System Setting ...............................................................................44
System Information....................................................................44
System Setting ...........................................................................45
Trap Setting................................................................................46
Password Setting........................................................................47
Statistic.......................................................................................47
Factory Reset .............................................................................48
Backup Setting...........................................................................49
Firmware Upload.......................................................................49
ii
Page 7
System Reboot...........................................................................50
Logout............................................................................................50
Technical Specifications.................................................................... 45
iii
Page 8
Page 9
ABOUT THIS GUIDE
Congratulations on your purchase of the ENMGS-16+2. This device integrates 1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package.
Purpose
This guide discusses how to inst al l your ENMGS-16+2.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to your ENMGS-16+2, and “switch” (first letter lower case) refers to other Ethernet switches.
1
Page 10
Page 11
INTRODUCTION
This chapter describes the features of the ENMGS-16+2 and some background information about Eth e rnet/Fast Ethernet/Gigabit Ethernet switching technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, flow control, and management objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade without wasting a company’s existing investment in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping with the network bottlenecks that frequently develop as computers and their busses get faster and more users use applications that generate more traffic. Upgrading key components, such as your backbone and servers to Gigabit Ethernet can greatly improve network response times as well as sig nificantly speed up the traffic between your subn e ts.
Gigabit Ethernet enables fast optical fiber connections to support video conferencing, complex imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of time.
3
Page 12
In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies. And with expected advances in the coming years in silicon technology and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded twisted-pair (UTP) cabling, outfitting your network with a powerful 1000-Mbps­capable backbone/server connection creates a flexible foundation for the next generation of network technology products.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks. A number of high-speed LAN technologies have been proposed to provide greater bandwidth and improve client/server response times. Among them, 100BASE-T (Fast Ethernet) provides a non-disruptive, smooth evolution from the current 10BASE-T technology. The non-disruptive and smooth evolution nature, and the dominating potential market base, virtually guarantees cost-effective and high performance Fast Ethernet solutions.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3 LAN committee. It is an extension of the 10Mbps Ethernet standard with the ability to transmit and receive data at 100Mbps, while maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments, it provides a straightforward upgrade and takes advantage of the existing investment in hardware, software, and personnel training.
4
Page 13
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which don’t compete with each other for network transmission capacity.
The switch acts as a high-speed selective bridge between the individual segments. The switch, without interfering with any other segments, automatically forwards traffic that needs to go from one segment to another. By doing this the total network capacity is multiplied, while still maintaining the same network cabling and adapter cards.
Switching LAN technology is a marked improvement over the previous generation of network bridges, which were characterized by higher latencies. Routers have also been used to segment local area networks, but the cost of a router, the setup and maintenance required make routers relatively impractical. Today switches are an ideal solution to most kinds of local area network congestion problems.
5
Page 14
VLAN (Virtual Local Area Network)
A VLAN is a group of end-stations that are not constrained by their physical location and can communicate as if a common broadcast domain, a LAN. The primary utility of using VLAN is to reduce latency and need for routers, using faster switching instead. Other VLAN utility includes:
Security, Security is increased with the reduction of opportunity in eavesdropping on a broadcast network because data will be switched to only those confidential users within the VLAN.
Cost Reduction, VLAN’s can be used to create multiple broadcast domains, thus eliminating the need of expensive routers.
Features
16 x 10/100/1000Mbps Auto-negotiation Gigabit Ethernet UTP
ports
2 x 1000Mbps mini-GBIC (Auto-Sense) for optional mini-GBIC
transceiver to extend distance, shared with 2 1000BASE-T ports
All 1000BASE-T ports support auto MDI/MDIX, so th ere is no
need to use cross-over cables or an up-link port
Half duplex transfer mode for connection speed 10Mbps and
100Mbps
Full duplex transfer mode for connection speed of 10Mbps,
100Mbps and 1000Mbps
Store-and-Forward switching scheme capability to support rate
adaptation and ensure data integrity
Up to 8K unicast addresses entities per device, self-learning, and
table aging
6
Page 15
512 KB packet buf fer Supports IEEE 802.3x flow control for full-duplex mode ports Supports IEEE 802.1Q VLAN Supports IEEE 802.1p Priority Queues Supports Static Port Trunk Supports Jumbo Frame Supports Broadcast Storm Control Supports Port Mirroring Supports Port Setti ng fo r Speed, Flow control Easy configuration via WEB Browser Easy setting via Web Management Utility Standard 19” R ack-mount size
7
Page 16
Page 17
UNPACKING AND INSTALLATION
This chapter provides unpacking and installation information for the Switch.
Unpacking
Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items:
One ENMGS-16+2, 16-Port 10/100/1000Mbps Web-Smart
Gigabit Ethernet Switch
One AC power cord, suitable for your area’s electrical power
connections
Four rubber feet to be used for shock cushioning Screws and two mounting brackets CD-Rom with Web Management Utility and User’s Guide
If any item is found missing or damaged, please contact your local reseller for replacement
Installation
The site where you install the hub stack may greatly affect its performance. When installing, consider the following pointers:
Install the Switch in a fairly cool and dry place. See Technical Specifications for the acceptable temperature and humidity operating ranges.
Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight.
9
Page 18
Leave at least 10cm of space at the front and rear of the hub for ventilation.
Install the Switch on a sturdy, level surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack installation, see the next section, Rack Mountin g.
When installing the Switch on a level surface, attach th e rubber feet to the bottom of each device. The rubber feet cushion the hub and protect the hub case from scratching.
Figure 1. Attach the adhesive rubber pads to the bottom
10
Page 19
Rack Mounting
The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each side), and secure them with the provided screws.
Figure 2. Combine the Switch with the provided screws
Then, use screws provided with the equipment rack to mount each switch in the rack.
Figure 3. Mount the Switch in the rack
11
Page 20
Connecting Network Cable
The Switch supports 1000Mbps Gigabit Ethernet that runs in Auto­negotiation mode and 10 Mbps Ethernet o r 100Mbps Fast Ethernet that runs both in half and full duplex mode and 1000Mbps Gigabit Ethernet runs in full duplex mode using four pairs of Category 5 cable.
These 1000BASE-T ports are Auto-MDI type port. The Switch can auto transform to MDI-II or MDI-X type, so you can just make an easy connection that without worrying if you are using a standard or crossover twisted-pair cable.
There are additional 2 ports combo mini-GBIC slot for optional mini­GBIC module.
AC Power
The Switch used the AC power supply 100-240V AC, 50-60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The switch’s power supply will adjust to the local power source automatically and may be turned on without having any or all LAN segment cables connected.
12
Page 21
IDENTIFYING EXTERNAL COMPONENTS
This chapter describes the front panel, rear panel, and LED indicators of the Switch.
Front Panel
The figure below shows the front panels of the Switch.
Figure 4. Front panel
LED Indicators:
Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below).
1000BASE-T Giga bit E ther net P or ts (Port 1~16):
The Switch sixteen Gigabit twisted pair ports, supported auto negotiable 10/100/1000Mbps and auto MDI/MDIX crossover detection function, this
function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub.
These ports can operate in half-duplex mode for 10/100Mbps and full- duplex mode for 10/100/1000Mbps.
Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.
13
Page 22
Combo mini-GBIC Ports (Port 15~16)
The Switch is equipped with two combo mini-GBI C ports, supported optional 1000BASE-SX/LX mini-GBIC module.
The 1000BASE-T port 15 and 16 are the same ports with the mini­GBIC port 15 and 16, when plug in the mini-GBIC module, the device will activate mini-GBIC, and the RJ45 port will be disabled.
Rear Panel
The rear panel of the Switch consists of an AC power connector and Reset button. The following shows the rear panel of the Switch.
Figure 5. Rear panel
AC Power Connector:
This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input vo ltages range from 100-240V AC at 50 - 60 Hz.
Reset:
The Reset button is to reset all the setting back to the factory default.
Note: Be sure that you recorded the setting of your device, else all the setting will be erased when pressing the “Reset” button.
14
Page 23
UNDERSTANDING LED INDICATORS
The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed.
Figure 6. LED indicators
Power and System LEDs
POWER: Power Indicator
On : When the Power LED lights on, the Switch is receiving power.
Off : When the Power turns off or the power cord has improper connection.
SYSTEM: Management Indicator
Blinking : When the CPU is working, the System LED is blinking.
On/Off : The CPU is not working.
15
Page 24
1000BASE-T Port 1~16 Status LEDs
Link/ACT: Link/Activity
On : When the Link/ACT LED lights on, the respective port is
successfully connected to an Ethernet network.
Blinking : When the Link/ACT LED is blinking, the port is transmitting or
receiving data on the Ethernet network.
Off : No link.
1000Mbps
On : When the 1000Mbps LED lights on, the respective port is connected
to a 1000Mbps Gigabit Ethernet network.
Off : When the respective port is connected to a 10Mbps Ethernet or
100Mbps Fast Ethernet network
100Mbps
On : When the 100Mbps LED lights on, the respective port is connected
to a 100Mbps Fast Ethernet network.
Off : When the respective port is connected to a 10Mbps Ethernet or
1000Mbps Gigabit Ethernet network.
16
Page 25
Combo mini-GBIC Port 15~ 16 Status LEDs
Link/ACT
On : When the fiber line connected to the mini-GBIC module is installed
and connected to a network, the Link/ACT LED will lights on.
Blinking : When the Link/ACT LED is blinking, the port is transmitting or
receiving data on the Gigabit Ethernet network.
Off : Fiber line or mini-GBIC module is not installed.
1000Mbps
On : When the 1000Mbps LED lights on, the respective port is connected
to a 1000Mbps Gigabit Ethernet network.
Off : When the respective port is connected to a 10Mbps Ethernet or
100Mbps Fast Ethernet network
17
Page 26
CONFIGURATION
Through the Web Browser you can configure the Switch such as VLAN, Port Trunking, Jumbo Frame… etc.
With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password and upgrading the new firmware.
Installing the Web Management Utility
The following gives instructions guiding you through th e installations of the Web Management utility.
1. Insert the Utility CD in the CD-Rom Drive.
2. From the Start menu on the Windows desktop, choose Run.
3. In the Run dialog box, type D:\Web Management
Utility\setup.exe (D:\ depends where your CD-Rom drive is located) and click OK.
4. Follow the on-screen instructions to install the utility.
5. Upon completion, go to Program Files -> Web Management
Utility and execute the Web Management utility. (Figure 7.)
18
Page 27
Figure 7. Web Management Utility
The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function, for details
instruction, follow the below section.
Discovery List
This is the list where you can discover all the Web management devices in the entire network.
By pressing the “Discovery” button, you can list all the Web Management devices in the discovery list.
Double click or press the “Add to monitor list” button to select a device from the Discovery List to the Monitor List.
19
Page 28
System word definitions in the Discovery List:
z MAC Address: Shows the device MAC Address. z IP Address: Shows the current IP address of the device. z Protocol version: Shows the version of the Utility protocol. z Product Name: Shows the device product name. z System Name: Shows the appointed device system name. z DHCP: Shows the DHCP status of the device. z Location: Shows where the device is located. z Trap IP: Shows the IP where the Trap to be sent. z Subnet Mask: Shows the Subnet Mask set of the device. z Gateway: Shows the Gateway set of the device.
Monitor List
All the Web Smart Device in the Monitor List can be monitored; you can also receive the trap and show the status of the device.
System word definitions in the Monitor List:
z S: Shows the system symbol of the Web-Smart device,
represent for device system is not alive.
z IP Address: Shows the current IP address of the device. z MAC Address: Shows the device MAC Address. z Protocol version: Shows the version of the Utility protocol. z Product Name: Shows the device product name. z System Name: Shows the appointed device system name. z DHCP: Shows the DHCP status of the device. z Location: Shows where the device is located. z Trap IP: Shows the IP where the Trap to be sent. z Subnet Mask: Shows the Subnet Mask set of the device. z Gateway: Shows the Gateway set of the device.
20
Page 29
View Trap: The Trap function can receive the events that happen from the Web Management Switch in the Monitor List.
There is a light indicator behind the “View Trap” button, when the light indicates in green, it means that there is no trap transmitted, and else when it indicates in red, it means that there is new trap transmitted, this is to remind us to view the trap. (
Figure 8)
Figure 8. View Trap button
When the “View Trap” button is clicked, a Trap Information window will pop out, it will show the trap information including the Symbol, Time, Device IP and the Event occurred. (
Figure 9)
The symbol “ ” represents the trap signal arise, this symbol will disappear after you review and click on the event record.
Figure 9. Trap Information
Note: In order to receive Trap information, switch has to be configured with Trap IP and Trap Events in Web browser, which are available in the Trap Setting Menu (see Page
46 for detail).
Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor.
Delete Item: To delete the device in the Monitor List.
21
Page 30
Device Setting
You can set the device by using the function key in the Device Setting Dialog box.
Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Set Trap to (Trap IP Address), System name, Location and DHCP function.
Select the device in the Discovery list or Monitor List and press this button, then the Configuration Setting window will pop out as Figure 10, after filling up the data that you want to change, you must fill up the password and press the “Set” to process the data changed immediately. The default password of this 16-Port 10/100/1000Mbps Web-Smart Gigabit Ethernet Switch configuration is “admin”.
Figure 10. Configuration Setting
Password Change: You can use this Password Change when you
need to change the password, fill in the password need ed in the dialog box and press “Set” button to proceed the password change immediately.
22
Page 31
Figure 11. Password Change
Firmware Upgrade: When the device has a new function, there will
be a new firmware to update the device, use this function to update.
Figure 12. Firmware Upgrade
Access Web: Double click the device in the Monitor List or select a
device in the Monitor List and press this “Web Access” button to access the device in Web browser.
DHCP Refresh: Press this “DHCP Refresh” button to refresh IP address of selected device form DHCP server.
23
Page 32
Toolbar
The toolbar in the Web Management Utility have four main tabs, File, View, Options and Help.
In the “File TAB”, there are Monitor Save, Monitor Save As, Monitor Load and Exit.
z Monitor Save: To record th e setting of the Monitor List to th e
default, when you open the Web Management Utility next time, it will auto load the default recorded setting.
z Monitor Save As: To record the setting of the Mon itor List in
appointed filename and file path.
z Monitor Load: To manually load the setting file of the
Monitor List.
z Exit: To exit the Web Management Utility.
In the “View TAB”, there are view log and clear log function, this function will help you to show trap setting.
z View Log: To show the event of the Web Management Utility
and the device.
z Clear Log: to clear the log.
In the “Option TAB”, there are Refresh Time function, this function helps you to refresh the time of monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min and 5 min to select the time of monitoring.
In the “Help TAB”, there is About function, it will show out the version of the Web Management Utility.
24
Page 33
Configuring the Switch
The 16-Port 10/100/1000Mbps Web-Smart Gigabit Ethernet Switch has a Web GUI interface for smart switch configuration. The Switch can be configured through the Web Browser. A network ad ministrator can manage, control and monitor the switch from the local LAN. This section indicates how to configure the Switch to enable its smart functions
Login
Before you configure this device, note that when the ENMGS-16+2 Switch is configured through an Ethernet connection, make sure the manager PC must be set on same the IP network. For example, when the default network address of the default IP address of the Web Smart Switch is 192.168.1.1, then the manager PC should be set at
192.168.1.x (where x is a number between 2 and 254), and the default subnet mask is 255.255.255.0.
Open Internet Explore r 5. 0 or above Web browser. Enter IP address
http://192.168.1.1 (the factory-default IP address
setting) to the address location.
Figure 13.
25
Page 34
Or through the Web Management Utility, you do not need to remember the IP Address, select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog page appears, remain enter the default password "admin" and press Login to enter the main configuration window.
Figure 14. Login
After entering the password, the main page comes up, the screen will display the device status.
Figure 15. System Information
26
Page 35
Configuration Menu
When the main page appears, find the Configuration menu in the left side of the screen (
Figure 16). Click on the setup item that you want to
configure. There are sixteen options: Port Setting, IEEE 802.1Q VLAN
Settings, Trunk Setting, Mirror Setting , IEEE 802.1p Default Priority, Broadcast Strom Control Setting, Jumbo Frame Setting, System Information, System Setting, Trap Setting, Password Setting, Statistics, Factory Reset, Backup Setting, Firmware Upload and System Reboot as shown in the Configuration Menu screen.
Figure 16. Configuration menu
27
Page 36
Configuration Setting
Find that there are seven items, including Port Setting, IEEE 802.1Q
VLAN Settings, Trunk Setting, Mirror Setting, IEEE 802.1p Default Priority, Broadcast Strom Control Setting, Jumbo Frame Setting in
Setup menu.
Port Settings
In Port Settings menu (Figure 17), this page will show each port’s status, selected drop down menu to set each port’s Speed, and QoS priority then press “Apply” button to activate changes. To refresh the information table to view the latest port setting and Link Status, press the Refresh button.
The Link Status in the screen will show the connection speed and duplex mode; else this dialog box will show Down when the port is disconnected.
Figure 17. Port Setting
Note: The priority of Gigabit Fiber port is higher than Copper.
Speed:
28
Page 37
The 1000BASE-T connections can operate in Forced Mode settings (1000M Full, 100M Full, 100M Half, 10M Full, 10M Half), Auto, or Disable. The default setting for all ports are Auto. The mini-GBIC (Gigabit Fiber) connections can operate in Forced Mode settings (1000M Full), Auto, or Disable
Flow Control:
This setting determines whether or not the Switch will be handling flow control. Set Flow Control to Enable for avoiding data transfer overflow. Or it sets to Disable; there is either no flow control or other hardware/software management.
When the port is set to forced mode, then the flow control will automatically set to Disable.
QoS:
Displays each port’s 802.1p QoS priority level for received data packet handling. Default setting for all ports is Middle. You can change the priority settings in 802.1p Default Priority.
29
Page 38
IEEE 802.1Q VLAN
A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area.
VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), o r multicast groups (multimedia applications such as video conferencing), and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections.
IEEE802.1Q VLAN function base on VID and PVID to distributes different VLAN groups. But IEEE802.1Q VLAN doesn't support multi-need server application via Untag port (Untag Port cannot overlap in different VLAN groups). For multi-need server application via Untag Port that the device support IEEE802.1Q Asymmetric VLAN function can be covered it.
30
Page 39
Asymmetric VLAN
IEEE 802.1Q Asymmetric VLAN default setting is “Disabled”, you can press “Enabled” ratio button and Apply it to submit the Asymmetric VLAN function. (Figure 18)
Figure 18. Enabled Asymmetric VLAN function
Figure 19. Change setting warning message
Note: The Settings of VLAN and Forwarding Table will be reset to default.
31
Page 40
Untag VLAN Setting:
The IEEE 802.1Q VLAN Configuration page provides powerful VID management functions. The original default VLAN setting has the VID as 01, named “default”, and contains all ports as “Untagged”.
Figure 20. 802.1Q VLAN Setting
Add VID: Click to create a new VID group, assigning ports from 01 to 16 as Untag, Tag, or Not Member. A port can be “Untagged” in only one VID. To save the VID group, press Apply.
Figure 21. Add New VID
32
Page 41
VID: A unique VLAN ID. VLAN Name: A VLAN name can be setting as user wi sh . Port: The switch port num ber. Untag: Outgoing frames without VLAN tag. Tag: Outgoing frames with VLAN tag. Not Member: The port num ber whi ch not to be grouped. Select All:
Select all ports to be VLAN members or not VLAN
members.
Cancel: To call the modifications off. Apply: To activate and save the modifications.
Figure 22. Delete VID
Delete: Click to delete selected VID.
33
Page 42
To change exist VLAN setting, press the VID to modify it.
Figure 23. Modify VID
Figure 24. Modify VID
PVID settings:
While receiving an untagged frame from the port, the switch will assign a tag to the frame, using the PVID of the port as its VID.
Figure 25. PVID settings
34
Page 43
Here is an example of two VLAN groups with several ports on each group and VLAN 1 (VID 01) does not have communication with VLAN 2 (VID 02).
Example1:
Figure 26. Untag VLAN setting example
Step1: Set VLAN1 member port 9~16 to “Not Member”, then apply setting. Step2: Create VID 2 and set port 9~16 to “Untag Port” member, then apply setting.
35
Page 44
802.1Q Asymmetric VLAN sett i ngs e xample: Port 1~16 in VLAN 1, port1~5 in VLAN 2, port1,6~9 in VLAN
3. All VLAN1~3 have access to Internet via port 1.
Note: The multi-need server must be support IEEE 802.1Q VLAN
Example2:
Figure 27. Asymmetric VLAN setting example
Step1: Enable Asymmetric VLAN function. Step2: Add VID2 and set port 1~5 to “Untag Port” member, then apply setting. Step3: Add VID3 and set port1 and Port 6~9 to “Untag Port” member, then apply
setting. Step4: Set PVID Port 2~9 PVID value to below list:
Figure 28. Asymmetric VLAN’s PVID setting example
36
Page 45
Tag VLAN Setting
The IEEE802.1Q protocol defines a new format of the frame; it adds a tag header in the original Ethernet frame, as follows:
IEEE802.1Q Tag VLAN is divided by VLAN ID (VID). On receiving a frame, the switch checks the VID in the tag header of the frame to decide which VLAN it belongs to. If the receiving frame doesn’t contain the tag header, the switch will assign a tag to the frame, using the PVID of the port as its VID.
Figure 29. Tag VLAN
37
Page 46
Example3:
Figure 30. Tag VLAN setting example
Step1: Set VLAN1 member port1 to “Tag Port” and port 9~16 to “Not Member”, then apply setting.
Step2: Add VID2 and set port1 to “Tag Port” and Port 9~16 to “Untag Port” member, then apply setting.
Note: The multi-need server must be support IEEE 802.1Q VLAN, th e sever uplink port is port1.
38
Page 47
Another example is about setting tag VLAN with two switches. Switch 1’s VLAN 1 (2 ~ 3 ports) have access to the Switch 2’s VLAN 1 (2 ~ 3 ports).
Example4:
Figure 31. Tag VLAN setting example
The settings of VLAN group for two devices are same. Step1: Set Switch1’s VLAN1 member port 1and 4~15 to “Not Member”, then apply
setting. Step2: Set Switch2’s VLAN1 member as Switch1. Step3: Uplink two switches via Port 16.
39
Page 48
Trunk Setting
The Trunking function enables the cascading of two or more ports for a combined larger bandwidth. Up to six Trunk groups may be created, each supporting up to 8 ports. Add a Trunking Name and select the ports to be trunked together, and click Apply to activate the selected Trunking groups.
Figure 32. Trunk Configuration
Be sure that the selected trunk setting port must connect to the device with a same VLAN group.
40
Page 49
Mirror Setting
Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the pack et can be studied. This enables network managers to better monitor network performances.
Figure 33. Mirror Setting
Selection of the Sniffer mode is as follow: TX (transmit) mode: this mode will duplicate the data transmit from
the source port and forward to the Sniffer port. RX (receive) mode: this mode will duplicate the data that send to the
source and forward to the Sniffer port. Both (transmit and receive) mode: this mode will duplicate both the
data transmit from and data that send to the source port, then it will forward to the Sniffer port.
41
Page 50
IEEE 802.1p Default Priority
This feature displays the status Quality of Service priority levels of each port, and for packets that are untagged, the switch will assign the priority in the tag depending on your configuration.
Figure 34. IEEE 802.1p Default Priority Setting
42
Page 51
Broadcast Storm Control Setting
The Broadcast Storm Control feature provides the ability to control the receive rate of broadcasted packets. If Enabled (default is Disabled), threshold settings of 8,000 ~ 4,096,000 bytes per second can be assigned. Press Apply for the settings to take effect.
Figure 35. Broadcast Storm Control Setting
Jumbo Frame Setting
Jumbo Frames enable the transportation of identical data in fewer frames. This ensures less overhead, lower processing time, and fewer interruptions. Maximum packet length supported is 10240 bytes.
Figure 36. Jumbo Frame Setting
43
Page 52
System Setting
Find that there are nine items, including System Information, System
Setting, Trap Setting, Password Setting, Statistics, Factory Reset, Backup Setting, Firmware Upload and System Reboot in System
menu.
System In formation
Press on the “System Information” to present the system information status on this screen, it will show the Product Name, Firmware Version, Protocol Version, MAC Address, System Name, Location Name, IP Address, Subnet Mask, Default Gateway, Trap IP, Login Timeout and System Up Time.
Figure 37. System Information
44
Page 53
System Setting
The System Setting includes IP Information and System information. There are two ways for the switch to attain IP: Static and DHCP (Dynamic Host Configuration Protocol).
When using static mode, the IP Address, Subnet Mask and Gateway can be manually configured. When using DHCP mode, the Switch will first look for a DHCP server to provide it with an IP address, network mask, and default gateway before using the default or previously entered settings. By default the IP setting is static mode.
By entering a System Name and System Location, the device can more easily be recognized through the Web Management Utility and in other Web-Smart devices on the LAN. The Login Timeout controls the idle time-out for security purposes, when there is no action in th e Web-based Utility. When the Login Timeout expires, the Web based Utility requires a re-login before using the Utility again.
Figure 38. System Setting
45
Page 54
Trap Setting
By configuring the Trap Setting, it allows Web Management Utility to monitor specified events on this Web-Smart Switch. By default, Trap Setting is Disabled. When the Trap Setting is Enabled, enter the Destination IP address of the managing PC that will receive trap information.
Figure 39. Trap Setting
System Events: Monitoring the system’s trap.
Device Bootup: a trap wh en booting up the system. Illegal Login: a trap when there is using a wrong password login,
and it will record from where the IP to be login.
Fiber Port Event: Monitoring the Fiber port status.
Link Up/Link Down: a trap when there is linking status happens in
mini-GBIC connection.
Twisted Pair Port Event: Monitoring the twisted pair port status.
Link Up/Link Down: a trap when there is linking status happens in
1000BASE-T connection.
46
Page 55
Password Setting
Setting a password is a invaluable tool for managers to secure the Web Smart Switch. After entering the old password and the new password two times, press Apply for the changes to take effect.
If you forget the password, press the “Reset” button in th e front panel of the Switch, the current setting includes VLAN, Port Setting… etc. will be lost and the Switch will restore to the default setting.
Figure 40. Password Setting
Statistic
The Statistic Menu screen will show the status of each port packet count.
Figure 41. Statistics
47
Page 56
Refresh: To renew the details collected and displayed. Clear Counter: To reset the details displayed.
To view the statistics of individual ports, click one of the Port ID as Figure .
Figure 42. Port Statistics
Factory Reset
The Factory Reset helps you to reset the device back to the default setting from the factory. All of the configuration will b e reset, the IP address of the device will be set to default setting 192.168 .1.1.
Figure 43. Factory Reset
48
Page 57
Backup Setting
The backup setting help you to backup the current setting of the Switch. Once you need to backup the setting, press the “Backup” button to save the setting.
To restore a current setting file to the device, you must specify the backup file and press “Restore” button to proceed the setting of the recorded file.
Figure 44. Backup Setting
Note: when restoring a recorded file, the current password will not be erased.
Firmware Upload
The Firmware Upload helps you to backup or upload firmware from/to the Switch. Once you need to backup the current firmware of the Switch, press the “Backup” button to save the current firmware of the Switch; To restore or upgrade firmware to the Switch, you must specify the firmware file and press “Upload” button to proceed the firmware upload.
Figure 45. Firmware Upload
49
Page 58
System Reboot
Provides to a safe way to reboot the system. Ensure the con figuration has been saved, or all the changes you just made may be lost after system reboot.
Figure 46. System Reboot
Logout
When press this function, the web configuration will go back to first Login page.
Figure 47.
50
Page 59
TECHNICAL SPECIFICATIONS
General
Standards IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3x Full Duplex Flow Control
IEEE 802.3z 1000BASE-SX/LX Gigabit Ethernet Protocol CSMA/CD Data Transfer
Rate
Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full- duplex)
Gigabit Ethernet: 2000Mbps (full-duplex) Topology Star Network Cables 10BASET: 2-pair UTP Cat. 3, 4, 5; up to 100m
100BASE-TX: 2-pair UTP Cat. 5; up to 100m
1000BASE-T: 4-pair UTP Cat. 5; up to 100m
Fiber module: mini-GBIC Fiber module Number of Ports 16 × 10/100/1000Mbps Auto-MDIX RJ-45 ports
2 × 1000Mbps mini-GBIC slots
Physical and Environmental
AC inputs 100-240V AC, 50-60 Hz internal universal power supply Power
Consumption
30 Watts (Max) Temperature Operating: 0~ 40oC, Storage: -10 ~ 70oC
Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90% Dimensions 440 x 210 x 44 mm (W x H x D) EMI: FCC Class A, CE Mark Class A, VCCI Class A
Certified: RoHS Safety: cUL (UL60950), CB (IEC60950)
45
Page 60
Performance
Transmits Method:
Store-and-forward RAM Buffer: 512KB per device
Filtering Address Table:
8K entries per device MAC Address
Learning:
Automatic update Packet Filtering /
Forwarding Rate:
10Mbps Ethernet: 14,880/pps
100Mbps Fast Ethernet: 148,800/pps
1000Mbps Gigabit Ethernet: 1,488,000/pps
46
Loading...