Encore ENLTV-3 - V4, ENLTV-3 User Manual

Page 1
ENLTV-3
PCI TV Tuner Adapter
User’s Guide
Page 2
ENLTV-3 User’s Guide
User’s Notice
WE PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL US, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS), EVEN IF WE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by us; or (2) the serial number of the product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent infringe.
z Windows, MS-DOS, and DirectX are registered trademarks of Microsoft Corporation. z Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated.
The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATION USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY US. WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright Encore Electronics © 2009. All Rights Reserved.
2
Page 3
ENLTV-3 User’s Guide
Contents:
Chapter 1: Introduction...................................................................................................................... 4
1.1 - Package Contents............................................................................................................... 4
1.2 - System Requirements........................................................................................................ 4
Chapter 2: Getting Started ................................................................................................................. 5
2.1 – ENLTV-3 Hardware Installation....................................................................................... 5
2.2 - Device Driver Installation ................................................................................................. 6
2.3 - Install the DirectX® ........................................................................................................ 13
2.4 - Install the ENLTV-3 Utility software. ............................................................................. 14
Chapter 3: Launch the ENLTV-3 Program ...................................................................................... 20
3.1 - Running the ENLTV-3 for the first time.......................................................................... 20
3.2 - Watch TV programs or movies from DVD/VCR/Camcorder ......................................... 22
3.3 - Video Recorder................................................................................................................ 23
3.4 - Using the Snapshot.......................................................................................................... 24
3.5 - Playback Video................................................................................................................ 24
3.6 - ImageViewer.................................................................................................................... 26
3.7 – Time-Shifting.................................................................................................................. 27
Chapter 4: Using the Remote Control.............................................................................................. 28
Chapter 5: Frequently Asked Questions.......................................................................................... 29
Chapter 6: Technical Support........................................................................................................... 30
3
Page 4
ENLTV-3 User’s Guide
Chapter 1: Introduction
1.1 - Package Contents
The following items are included in the ENLTV-3 package.
z CD setup disc (includes Software Driver and Utility Software) z ENLTV-3 PCI card z Video cable z Remote sensor cable z Remote controller z User’s guide
1.2 - System Requirements
z Intel® Pentium® 4 1.7GHz CPU or above z Minimum 256 MB memory z Minimum 1GB hard disk space available z 1024x768 graphic card, DirectX® 9.0c or above compatible graphic card or higher z One free PCI slot z PCI 2.1 or 2.2 compliant interface z Microsoft Windows® XP/ Windows® Vista z CD-ROM drive
4
Page 5
ENLTV-3 User’s Guide
Chapter 2: Getting Started
2.1 – ENLTV-3 Hardware Installation
Install the ENLTV-3 PCI Card to the computer’s
available PCI slot according to your computers
manual and new hardware installation procedures.
Make sure that the computer’s power cord is
unplugged before inserting the ENLTV-3 card to the
PCI slot. ENLTV-3 supports PCI bus 2.1 and above.
Refer to the device connection diagram below for port connections:
Caution:
Take an extra care handling the Remote sensor cable, do not insert or remove the sensor cable while the computer is powered-on. Otherwise, it can cause the ENLTV-3 to malfunction.
5
Page 6
ENLTV-3 User’s Guide
2.2 - Device Driver Installation
1. Placed the CD software that comes with the ENLTV-3 in the CD-ROM drive. (Assuming
that the ENLTV-3 Tuner card is properly installed to the computer’s PCI slot), then
follow the on-screen installation guide below.
Device driver installation for Windows® XP Home/Professional Edition/x64 Edition
1. When the computer is powered-on for the
very first time during the setup, a
message “Found New Hardware Wizard”
dialogue box will appear on the screen.
Click “Cancel” button to close “Found New Hardware Wizard” window.
2. Insert the installation CD into the
CD-ROM drive. The setup screen will
automatically appear.
3. Click the “Setup Driver” button.
4. Select the language then click “Next”.
6
Page 7
ENLTV-3 User’s Guide
5. Click “Next” on driver setup welcome
window to continue.
6. Click “Install” to begin install driver.
7. Click “Next” button.
7
Page 8
ENLTV-3 User’s Guide
8. Click “Continue Anyway” to continue the
installation.
9. Click ”Continue Anyway” button
10. Click “Finish” button
8
Page 9
ENLTV-3 User’s Guide
11. Click “Finish” to reboot PC.
12. To make sure the driver is properly
installed and started, open the “Device
Manager”. Please double-click the
“Sound, video and game controller”.
9
Page 10
ENLTV-3 User’s Guide
Device driver installation for Windows® Vista
1. After ENLTV-3 hardware has been
installed, the next time when the computer
is powered-on, a message “Found New
Hardware” dialogue box will appear on the
screen. Click “Cancel” button to close
“Found New Hardware” window.
2. Insert the installation CD into the
CD-ROM drive. The setup screen will
automatically appear.
3. Click the “Setup Driver” button.
4. Select the language then click “Next”.
10
Page 11
ENLTV-3 User’s Guide
2. Click “Next” on driver setup welcome
window to continue.
3. Click “Install” button.
4. Click “Next” button.
11
Page 12
ENLTV-3 User’s Guide
5. Click “Finish” button.
6. Click “Finish” button.
7. To make sure the driver is properly
installed and started, open the “Device
Manager”. Please double-click the
“Sound, video and game controller”.
12
Page 13
ENLTV-3 User’s Guide
2.3 - Install the DirectX®
Microsoft DirectX® allows 3D hardware acceleration support in Windows® 98, 2000,
Windows® XP 32bit/64bit and Windows® Vista 32bit/64bit. For software MPEG support in
Windows® 98, you must first install Microsoft DirectX®, and then an MPEG compliant
video player. Follow the installation steps below to install MS DirectX®.
1. Insert the installation CD into the
CD-ROM drive. The setup screen will
automatically appear.
2. Click the “DirectX” button.
3. Click “Accept the agreement” radio button
then click “Next”
4. Click “Next” to confirm the installation of
DirectX
5. Click “Finish”
NOTE: The computer will automatically restart. Please close all programs if any and save files if needed before hitting the “Finish” button.
13
Page 14
ENLTV-3 User’s Guide
2.4 - Install the ENLTV-3 Utility software.
1. Install TV application on Windows® XP 32bit/64bit
1. Insert the installation CD into the
CD-ROM drive. The setup screen should
automatically appear.
2. Click the “Setup Utility
3. Select the language then click “Next”.
4. Click “Next” button.
14
Page 15
ENLTV-3 User’s Guide
5. Please read the License Agreement and
click “Yes” button
6. Make sure the “Typical” radio button is selected then click “Next”.
7. Click “Next” button to accept the default
location or choose a different folder
Note: (We recommend not to change the default location)
15
Page 16
ENLTV-3 User’s Guide
8. Click “Next” button.
9. Click “Finish” to restart your computer
NOTE: We recommend restarting your computer right after the Installation Wizard.
16
Page 17
ENLTV-3 User’s Guide
2. Install TV application on Windows® Vista 32bit/64bit
1. Insert the installation CD into the
CD-ROM drive. The setup screen should
automatically appear.
2. Click the “Setup Utility
3. Select the language then click “Next”.
4. Click “Next” button.
17
Page 18
ENLTV-3 User’s Guide
5. Please read the License Agreement and
click “Yes” button
6. Make sure the “Typical” radio button is selected then click “Next”
7. Click “Next” button to accept the default
location or choose a different folder
Note: (We recommend not to change the default location)
18
Page 19
ENLTV-3 User’s Guide
8. Click “Next”
9. Click “Finish” to restart your computer.
NOTE: We recommend restarting your computer right after the Installation Wizard.
19
Page 20
ENLTV-3 User’s Guide
Chapter 3: Launch the ENLTV-3 Program
3.1 - Running the ENLTV-3 for the first time
Click “Start”, move your mouse to “Programs\ENLTV-3” then click ENLTV-3
NOTE: When the ENLTV-3 Program is first started, it will prompt you to configure the Device Setting.
20
Page 21
ENLTV-3 User’s Guide
1. Select the video signal format in your area (NTSC
or PAL) from the “TV T uner St andard” drop-down
menu.
2. Click “Next”
3. This step will give you an option to scan for TV
channels. Select which signal source you are
connected to in the “TV Scan Type” line then click “Search”. There are two types of scans.
i. One is scan by TV channel table “Cable”,
“Antenna” and “Extend
ii. One is scan by frequency that scans low
frequency to high frequency. The “Auto”
scan mode is not for the TV table order.
21
Page 22
ENLTV-3 User’s Guide
3.2 - Watch TV programs or movies from DVD/VCR/Camcorder
1. Source Switch: click it to select TV, Audio/Video or S-Video
2. Search TV channel: click to search available TV channel.
4.Channel Control
5.Double click to full screen
3.Volume Control
6.Channel List
2.Search TV Channel
1.Source Switch
7.TV wall
3. Volume control: Adjust the Volume or mute.
4. Channel control: Set channel up or down’
5. Double click to full screen display or right click for the program menu
6. Channel List: This is listing all available TV channel.
7. TV wall display: show 4x4 TV wall on screen.
22
Page 23
ENLTV-3 User’s Guide
When you do a full screen display, you can use the panel bar to set up your TV box.
1. Fix Panel: To fix the display panel. Show / Hide as mouse drags.
2. Hide Panel: To hide the sub-panel.
3. Snapshot: Same as "Snapshot" button of main panel.
4.
TV Wall: To launch TV Wall function, same as "TV Wall" button,
5.
Start / Stop Record: Record the current playing audio/video, same as "Start/Stop
Record" of main panel.
6. Switch Next Channel: Switch to next channel, same as "Switch Next Channel" button
of main panel.
7. Switch Previous Channel: Switch to previous channel, same as "Switch Previous Channel" button of main panel.
8. Volume Adjustment: To adjust the output volume, same as "Volume Adjust" scroll bar
of the main panel.
9. Mute: Audio Mute
3.3 - Video Recorder
1. Click the “Setting” button to setup the record
format.
2. Setup the video format then click “OK”.
3. Click “Record” button to start to capturing
video.
23
Page 24
ENLTV-3 User’s Guide
3.4 - Using the Snapshot
1. Click the “Setting” button to setup the image
format.
2. The ENLTV-3 support BMP and JPEG image
format. The default is JPEG. Please choose
your desired format.
3. Click “Snapshot” button to capture image.
3.5 - Playback Video
1. Click “Playback” button to select video file.
2. Choose the video then click “open” button.
Movie Player function List:
About: To show the current version info
24
Page 25
ENLTV-3 User’s Guide
Exit: To exit the video playback window, [Esc] or [ALT]+[F4] on keyboard equalized
Minimize: To minimize the video playback window, click "MoviePlayer" in desktop
taskbar to restore display
Hide Control Panel: To hide video control panel, right click video window and select
"Control Panel" to restore display
Options: Click to open "Options" dialog and adjust settings for video window,
snapshots, and playlist
ImageViewer: To open image folder (refer to “3.6 ImageViewer” on page 26.) Step Backward: Step by step rewind recorded video
Step Forward: Step by step forward recorded video Slow Backward: To slow rewind play recorded video Slow Forward: To slow forward the video Fast Backward: To fast rewind play recorded video
Fast Forward: To fast forward play recorded video
Mute: To turn off audio, click again to restore
Volume Adjust: Drag the slider with the mouse or use Left and Right arrow
on keyboard to adjust volume
Play/Pause: Click to play the current video file, click again to pause, click once
more to continue
Stop Play: Stop
Snapshot: Capture current video frame as BMP or JPG image
Default saved file name is “snapshot time” and saved under C:\My Pictures. You also can open "Snap Setting" option in "Options" to set snapshot saving directory, image format, and select rename file.
Playlist: Show/Hide the Play List Window. By default, video files shown are from
the record directory, C:\Video\
25
Page 26
ENLTV-3 User’s Guide
3.6 - ImageViewer
1. Click the “ImageViewer” to retrieve the
saved pictures.
2. You can use the “ImageViewer” software to
control picture zoom in/out, or rename.
The menu bar contains many function buttons for easy operations, these are:
Refresh: To refresh the display snapshot image in current folder.
DirBar: Show/Hide the Direct Panel on the left window Pane, through which you
can browse and select folder.
ImageBar: Show/Hide the Image Bar on the left of window, through which you
can preview snapshot image.
Set Wallpaper: Set the current image as wallpaper of the Windows desktop, click
the right dropped arrow you can select wallpaper display mode.
Skin: To set the skin of the image browser window
Zoom out: To shrink display current image
Zoom in: To magnify current image
Match Zoom: You can select the matched display mode in the drop-down arrow
Full Size: Shows image at 100% magnification
Fit Image: Magnifies image to fit screen or window
Fit Width: Magnifies image to fit width of screen or window
Fit Height: Magnifies image to fit height of screen or window
Lock: Locks the viewer at the current zoom level.
26
Page 27
ENLTV-3 User’s Guide
3.7 – Time-Shifting
1. Right click inside the ENLTV-3 video
window and select the “Timeshift”
function
2. Video is now being recorded to your
hard disk while showing live on screen.
You can click “pause” button or slide the
“timer” to control the current TV show.
3. Click “Stop” button on the control panel
or right click inside the ENLTV-3 video
window and select “Stop” from the
context menu to stop the time-shift
function.
TimeShift
27
Page 28
ENLTV-3 User’s Guide
Chapter 4: Using the Remote Control
The Remote control allows you to operate the ENLTV-3 program, such as turning the TV
on or off, changing channel and volume, etc. Aim the upper front side of the Remote
Control to the Remote Control Receiver as you would do on other infrared remote control.
For default button assignments, please refer to the list below:
Remote Control Default Settings:
1. Open or Close TV Program.
2. Mute
3. Number keys.
4. Single or Double digits channel.
5. Return to the previous channel last viewed
6. Switch TV signals, S-Video and A/V signal
7. Snapshot
8. Channel Up
9. Channel Low
10. Volume High
11. Volume Low
12. Full screen
13. Record
14. Record Pause
15. Video Settings:Click to respectively adjust
video brightness, contrast, hue and saturation
(use together with the right two direction key).
16. Decrease video setting.
17. Increase video setting.
18. Click to set video brightness, contrast, hue
and saturation to default value.
19. Hide / Display Control Panel.
20. Set time to shutdown Windows system.
28
Page 29
ENLTV-3 User’s Guide
Chapter 5: Frequently Asked Questions
Q I can’t use ENLTV-3 when I run the software and it shows an error message.
A: This problem is because of incorrect sound card device driver, or the driver and software did not mach.
1. Incorrect sound card device driver
Check the Device Manager for any yellow or red markings under “Sound, Video and Game Controller”. If you see yellow or red markings your sound card may be bad or not working correctly.
Check the sound card settings in Control Panel to make sure the correct sound card is selected (This happens to PC with more than one sound card and Bluetooth device)
Check the Device Manager > Sound, Video and Game Controller. After the driver installation you should see a line that says “TV Tuner Card”. If you don’t see it that means the driver for ENLTV-3 is not installed.
2. The ENLTV-3 driver and software does not match The ENLTV-3 driver and software should match. If step 1 did not work to fix the problem,
uninstall the driver and the software, and then reinstalling then from the product CD again. If your product CD is not available with you, you can check our web site at http://www.encore-usa.com for download.
29
Page 30
ENLTV-3 User’s Guide
Q: How do I uninstall the ENLTV-3 software?
A: For Windows® Vista, there are two way to uninstall the ENLTV-3 Utility software
1. Go to Start > All Program > ENLTV-3 > Uninstall ENLTV-3 program.
2. Go to Windows “Control Panel” > “Add or Remove programs” Select ENLTV-3 then click “Remove” button
Q Why doesn’t the “Record” function work? I can watch a TV programs fine, but when I hit the “Record” button, nothing is saved to my hard disk drive.
AThis can be a Windows account or user rights issue.
1. In Windows® Vista system, use “Administrator” account type to login and try to record again.
2. Recording function use a video CODEC to encode a movie. To make sure video CODEC resource is not being occupied, we suggest reinstalling the ENLTV-3 utility software, this way the CODEC link will also be reset.
3. Make sure that you meet the minimum system requirements.
Chapter 6: Technical Support
For Technical Support or Installation Hotline contacts please visit our web site at
http://www.encore-usa.com
30
Page 31
ENLTV-3 User’s Guide
31
Page 32
2009/08/01
Version: 4.0
Loading...