Encore ENHGS-800X4, ENHGS-500X2 User Manual

ENHGS-500X2

5-Port Gigabit Switch

ENHGS-800X4

8-Port Gigabit Switch

User’s Manual

FCC Certifications

This Equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.

CE Mark Warning

This equipment complies with the requirements relating to electromagnetic compatibility, EN
55022 Class A for ITE, the essential protection requirement of Council Directive 89/336/EEC on
the approximation of the laws of the Member States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that information
in this document is not up-to-date. Please check with your local distributors for the latest
information. No part of this document can be copied or reproduced in any form without written
consent from the company.

Trademarks:
All trade names and trademarks are the properties of their respective
companies.

Encore Electronics Inc., Copyright © 2010, All Rights Reserved.

Introduction

The ENHGS-500X2 / ENHGS-800X4, a powerful and high-performance 5 /
8-Port 10/100/1000 Mbps gigabit Ethernet switch, is the best solution for
expanding your network environment. ENHGS-500X2 / ENHGS-800X4 5 /
8-Port gigabit switch is fully non-blocking architecture and compliant with all
kinds of network protocols. ENHGS-500X2 / ENHGS-800X4 supports every
switching port with wire-speed performance and delivers a dedicated
10/100/1000 Mbps connection to every attached client with no bandwidth
congestion issue.
Gigabit speed is 10 times quicker than 100Mbps fast Ethernet connection,
enabling you to save time transferring bandwidth-intensive music, video, photos,
graphic, and data files. Store-and-forward switching mode promises a low
latency plus eliminates all the network errors, including runt and CRC error
packets. ENHGS-500X2 / ENHGS-800X4 can provide a backbone link to your
switched workgroup or a server fat-pipe link. With flexible architecture, users can
easily implement a wired network without bandwidth limitations.

Before you start to install the switch, check the following contents in this
package：

 One ENHGS-500X2 or ENHGS-800X4
 One power adapter
 User’s manual

Led Definition

Please refer to the following table for LED definition:

ENHGS-500X2 (5-Port switch)

ENHGS-800X4 (8-Port switch)

LED Status Operation

Power Steady Green Power is on
Off Power is off
Link/ACT Steady Green Port connected
Blinking Green The port is transmitting/receiving data

Stations connection

Connect each station to the switch by twisted-pair cable. Plug one RJ-45
connector into a RJ-45 port of the switch, and plug the other RJ-45 connector
into the station’s network adapter. Power on the switch and then system is ready .
For cable selection, refer to the following table.

Switches Connection

In making a switch interconnection, you could use any port to connect another
switch with straight or crossover cable. As all the ports support auto MDI / MDI-X
function, using a straight cable to make a switch-to-switch connection is allowed.

For cable selection, refer to the following table：

Network Speed Cable Type Max. Length

10Mbps Cat. 3, 4, 5 UTP/STP 100 meters
100Mbps Cat. 5 UTP/STP 100 meters
1000Mbps Cat. 5 UTP/STP 100 meters

Specification

IEEE 802.3 10BASE-T

Standard

Interface
Uplink

Network Speed

MAC Address
Table

Buffer Memory

Jumbo Frame

External Power
Supply

IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x full duplex operation and flow control
5 ports / 8 ports - 10/100/1000 Mbps RJ-45 Gigabit Ethernet
Auto MDI/MDI-X（Auto crossover）
10/100/1000Mbps
Full/Half duplex mode auto detection (1000Mbps for Full duplex
only)
1K MAC entries (ENHGS-500X2)
4K MAC entries (ENHGS-800X4)
104K bytes (ENHGS-500X2)
128K bytes (ENHGS-800X4)
12K bytes (ENHGS-500X2)
16K bytes (ENHGS-800X4)

5V 2A

Certification

CE, FCC part 15 Class B