Encore ENDSL-A2PLUS4R2, ENDSL-R2PLUS4R2 User Manual

ENDSL-A2+4R2

ADSL2+ Modem

Four Port Full-Rated Router

User’s Manual

JULY 2007

Copyright © 2007 Encore Electronics Inc.. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.

Disclaimer

This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary se rvicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

Caution

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Contents

1. Introduction.............................................................................................4

1.1 Introduction to ENDSL-A2+4R2 router....................................................... 4

1.2 Product Features........................................................................................ 4

2. Hardware Installation..............................................................................7

2.1 System Requirements................................................................................ 7

2.2 Package Contents...................................................................................... 7

2.3 Front Panel Indicators and Description...................................................... 7

2.4 Back Panel................................................................................................. 8

2.5 Connect Related Devices........................................................................... 9

3. Connecting ENDSL-A2+4R2 Router via Ethernet and USB...............10

3.1 Setup ENDSL-A2+4R2 router via Ethernet Cable.................................... 10

3.2 Setup ENDSL-A2+4R2 router via USB Cable .......................................... 10

3.3 Configure TCP/IP...................................................................................... 18

3.4 USB Device Driver Installation on MAC OS ............................................. 33

4. Configure ENDSL-A2+4R2 Router via HTML Interface....................41

4.1 Login......................................................................................................... 41

4.2 Quick Start................................................................................................ 42

4.3 Interface Setup ......................................................................................... 44

4.3.1 Internet.............................................................................................44

4.3.2 LAN .................................................................................................48

4.4 Advanced Setup .......................................................................................... 50

4.4.1 Firewall............................................................................................50

4.4.2 Routing.............................................................................................50

4.4.3 NAT..................................................................................................52

4.4.4 QoS ..................................................................................................55

4.4.5 VLAN ..............................................................................................56

4.4.6 ADSL...............................................................................................57

4.5 Access Management................................................................................... 58

4.5.1 ACL..................................................................................................58

4.5.2 IP Filter ............................................................................................59

4.5.3 SNMP...............................................................................................63

4.5.4 UPnP................................................................................................63

4.5.5 DDNS...............................................................................................64

4.5.6 CWMP .............................................................................................65

4.6 Maintenance............................................................................................. 67

4.6.1 Administration .................................................................................67

4.6.2 Time Zone........................................................................................67

4.6.3 Firmware..........................................................................................68

4.6.4 System Restart .................................................................................69

4.6.5 Diagnostic........................................................................................70

4.7 Status ....................................................................................................... 71

4.7.1 Device Info.......................................................................................71

4.7.2 System Log ......................................................................................73

4.7.3 Statistics...........................................................................................74

5. Troubleshooting....................................................................................75

5.1 Using LEDs to Diagnose Problems .......................................................... 75

5.1.1 Power LED..........................................................................................75

5.1.2 LAN LED............................................................................................75

5.1.3 ADSL LED..........................................................................................76

5.2 Problems with the Web Interface.............................................................. 76

5.3 Problems with the Login Username and Password.................................. 77

5.4 Problems with LAN Interface.................................................................... 77

5.5 Problems with WAN Interface................................................................... 77

5.6 Problems with the Internet Access............................................................ 78

1. Introduction

1.1 Introduction to this ADSL2+ router

This ENDSL-A2+4R router is a full-featured ADSL router that provides Ethernet direct connections to individual PCs or local area network with 10/100 Ba se-T Ethernet . This prod uct use advanced ADSL chipset solution with complete set of industry standard features and high-speed ADSL, ADSL2 and ADSL2+ Internet access solution for SOHO and residential users. User can enjoy higher quality multimedia and real-time applications such as online gaming, Video-on-Demand and other bandwidth consuming services. Also the feature-rich routing functions are seamlessly integrated to ADSL service for existing corporate or home users.

1.2 Product Features

 Application Diagram

 High Speed Internet Access

This ENDSL-A2+4R router complies with ADSL / ADSL2 / ADSL2+ standards. It can support downstream rates of up to 24Mbps and upstream rates of up to 1Mbps. This ADSL router is compliant with the following standards.

z ANSI T1.413 issue 2 z ITU-T G.992.1 (G.dmt) z ITU-T G.992.2 (G.lite) z G.994.1 (G.hs, Multimode) z ITU-T G.992.3 (ADSL2 G.dmt.bis) z ITU-T G.992.4 (ADSL2 G.lite.bis) z ITU-T G.992.5 (ADSL2+; Annex A, B, I, J, L & M) z Reach Extended ADSL (RE ADSL)

 Quick Installation Wizard

Support Quick Installation Wizard Web GUI and Easy setup software to install this ADSL

router easily and quickly.

 Multi-connection protocol support

z Multi Protocol over AAL5 (RFC1483 / 2684) z Classical IP over ATM (RFC 1577) z VC and LLC Multiplexing z PPP over Ethernet (RFC 2516) z PPP over ATM (RFC 2364)

 Network Address Translation (NAT)

Network Address T ranslati on (NAT) allows the translation of an Internet protocol address used within one network (for example a private IP address used in a local network) to a different IP address known within another network (for example a public IP address used on the Internet).

 Universal Plug and Play (UPnP)

Universal Plug and Play is a standard that uses Internet and Web protocols to enable devices such as PCs, peripherals, intelligent appliances, and wireless devices to be plugged into a network and automatically know about each other. simple and robust connectivity among stand-alone devices and PCs.

This protocol is used to enable

 Dynamic DNS Support

With Dynamic DNS support, you can have a static hostname alias for a dynamic IP address, allowing the host to be more easily accessible from various locations on the Internet. You must register for this service with a Dynamic DNS client.

 DHCP Support

DHCP (Dynamic Host Configuration Protocol) allows individual clients to obtain TCP/IP configuration at start-up from a centralized DHCP server. The ADSL router has built-in DHCP server capability enabled by default. It can assign IP addresses, an IP default gateway and DNS servers to DHCP clients. It can also act as a surrogate DHCP server (DHCP Relay) where it relays IP address assignment from the actual real DHCP server to the clients.

 Device Management

z Web-based GUI Configuration / Management z Command-line Interpreter (CLI) z Telnet Remote Management z Firmware upgrade via FTP / TFTP (Web-based GUI) z Built-in Diagnostic tool and IP Ping

 SNMP (Simple Network Management Protocol) Support

It’s an easy way to remote control the router via SNMP.

 10/100M Auto-negotiation Fast Ethernet switch

This auto-negotiation feature allows the router to detect the speed of incoming transmissions and adjust appropriately without manual intervention. It allows data transfer of either 10 Mbps or 100 Mbps in either half-duplex or full-duplex mode depending on your Ethernet network.

 Multiple PVC (Permanent Virtual Circuits) Support

z Supports OAM F4/F5 loop-back, AIS and RDI OAM cells. z ATM Forum UNI 3.1/4.0 PVC

z Support up to 8PVCs.

 Bridging / Routing support

z Ethernet to ADSL self-learning Transparent Bridging (IEEE 802.1D) z IP routing-RIPv2 (backward compatible with RIPv1) z Static IP routing z Routing (TCP/IP/UDP/ARP/ICMP) z IP Multicast IGMP v1/v2

 Security

z PPP over PAP (Password Authentication Protocol; RFC1334) z PPP over CHAP (Challenge Authentication Protocol; RFC1994) z VPN (IPsec, PPTP, L2TP) pass through z Built-in NAT Firewall z IP-based Packet filtering z Password Protected System Management

2. Hardware Installation

2.1 System Requirements

z Pentium III 266 MHz processor or higher z 128 MB RAM minimum z 20 MB of free disk space minimum z RJ45 Ethernet Port z USB Port z CD-ROM drive

2.2 Package Contents

z ADSL Ethernet Router z RJ-45 Ethernet cable z RJ-11 Phone cable z USB Cable z Power Adapter z Software driver CD z Quick Installation Guide

2.3 Front Panel Indicators and Description

Front panel of ADSL router has LED indicators to display router’s operating status.

One-Port ADSL Router Front Panel

○ ○ ○ ○ ○

ADSL DATA LAN USB PWR

Descriptions of LED status

ADSL

DATA When router is transferring data between Internet and router, this LED will be flashing.

LAN

When connection with Internet (ADSL Connected) is established, this LED will light up. When this LED is flashing: NO ADSL physical connection

When connection 10/100MB with end user is established, this LED will light up. When router is transferring data between router and end user, this LED will be flashing.

USB When an active USB cable is connected with router, this LED will light up.

PWR When an active power adapter is connected with router, this LED will light up.

Four-Port ENDSL-A2+4R Router Front Panel

○ ○ ○ ○ ○ ○ ○

PWR USB LAN4 LAN3 LAN2 LAN1 ADSL

Descriptions of LED status

PWR When an active power adapter is connected with router, this LED will light up.

USB When an active USB cable is connected with router, this LED will light up. LAN4 When port 4 connection with PC or Switch / Hub is established, this LED will light up. LAN3 When port 3 connection with PC or Switch / Hub is established, this LED will light up. LAN2 When port 2 connection with PC or Switch / Hub is established, this LED will light up. LAN1 When port 1 connection with PC or Switch / Hub is established, this LED will light up.

When connection with Internet (ADSL Connected) is established, this LED will light up.

ADSL

When this LED is flashing: NO ADSL physical connection

2.4 Back Panel

One-Port ENDSL-A2+R Router

LINE USB DEFAULT LAN PWR ON/OFF

Descriptions of All Connectors

LINE Connect with phone cable

USB Connect with USB cable to PC

DEFAULT Reset button.

LAN Connect with Ethernet Cable to Switch Hub or PC

PWR Connect with power adapter

ON/OFF Power switch button

Four-Port ENDSL-A2+4R Router

ON/OFF PWR 1X 2X 3X 4X DEFAULT USB

Descriptions of All Connectors

ON/OFF Power switch button

PWR Connect with power adapter

1X Connect with Ethernet Cable to Switch Hub or PC 2X Connect with Ethernet Cable to Switch Hub or PC 3X Connect with Ethernet Cable to Switch Hub or PC 4X Connect with Ethernet Cable to Switch Hub or PC

DEFAULT Reset button

USB Connect with USB cable to PC

LINE Connect with phone cable

2.5 Connect Related Devices

1) Connect Router to LINE Plug the provided RJ-11 phone cable into LINE port on the back panel of the router and insert the other end into splitter or wall phone jack.

2) Connect Router to LAN Plug RJ-45 Ethernet Cable into LAN port on the back panel of the router and insert the other end of the Ethernet cable on your PC’s Ethernet port or switch / hub.

3) Con nect Router to Power Adapter Plug Power Adapter to PWR port on the back panel of the router and the other end to a power outlet.

4) Press ON/OFF button to start the router

5) If you connect your router via USB cable, plug the provided USB cable into USB

port on the back panel of the router and insert the other end of the USB ca ble to PC.

Warning! Only use the power adapter provided in the package, otherwise it may cause

hardware damage.

3. Connecting ENDSL-A2+4R Router via Ethernet and USB

You can connect ENDSL-A2+4R router with PC through either Ethernet cable or USB cable. After connection is established, you can configure the host PC to be a DHCP client. You have to repeat the same steps for every host PC on your network if you use DHCP function on your router.

3.1 Setup ENDSL-A2+4R router via Ethernet Cable

If there is an available LAN card present on your PC, you just simply connect ADSL router and PC through the Ethernet cable. Once you establish Internet connection, you could browse the Web through the Ethernet cable.

3.2 Setup ENDSL-A2+4R router via USB Cable

You can connect the ENDSL-A2+4R router with PC via USB cable when there is no LAN card present on your PC. USB cable acts as another LAN connection in this scenario. Once you establish Internet connection, you could browse the Web through the USB cable.

USB Device Driver Installation for Windows Vista/XP/2000/ME/98SE

Step 1: Connect ENDSL-A2+4R Router and PC with USB cable. Step 2: Once “Found New Hardware Wizard” window pops out, chooses “Install from a list

or specific location (advanced)” and click “Cancel”:

(Figure 1: For Windows Vista)

(Figure 2: For Windows 2000 and XP)

(Figure 3: For Windows 98SE and ME)

Step 3: Insert the installation CD and the Easy Setup main page will appear as below,

Install USB Driver: If router is connected through USB cable, click here to install USB driver. Quick Setup: If router is connected through Ethernet cable or after USB driver is loaded, click

here to set the ADSL Router. USER MANUAL: This CD provides Easy Setup and ADSL Router. Easy Setup describes the installation procedures via Quick Setup utility and ADSL Router describes detailed router setup and configuration. Adobe: Click here to install Acrobat Reader. (Acrobat 8 Reader for Windows Vista/XP; Acrobat 6 Reader for Windows 2000/ME/98SE) Panda: Click here to start Panda Anti Virus program. (Panda only supports Windows XP/2000/ME/98SE OS).

Exit: Click here to exit the installation procedures

Step 4: If router is connected with USB cable, click “Install USB Driver”, the software kit will

automatically install USB driver. Please wait for a while during the configuration.

Step 5: For Windows XP OS, Click “Continue Anyway” to process the next step.

Step 6: After device installation has successfully installed ADSL USB Modem, click “OK” to

exit.

[Note] In Windows 98SE Operation System, the setup program will ask restart the computer

to complete the installation. Please follow the below processes:

Step 6: Click “OK” to restart your computer.

Step 7: After system is rebooted, Insert Disk information window will show as below, click

“OK” to continue.

Step 8: The program will automatically direct the program files which is necessary. Click “OK”

to continue.

Step 9: After complete the installation process, the system will ask to restart your

computer. Please click “Yes” to reboot your system again.

To verify your router is installed properly, please follow the below descriptions:

[For Windows Vista]

Go through “Start Æ Control Panel Æ System Æ Device Manager” to check if USB

device is installed properly.

[For Windows XP]

Go through “Start Æ Control Panel Æ

System Æ Hardware Æ Device Manager”

to check if USB device is installed properly.

[For Windows 2000]

Go through “Start Æ Settings Æ Control

Panel Æ System Æ Hardware Æ Device Manager” to check if USB device is installed

properly.

[For Windows 98SE & ME]

After OS boots up, go through “Start Æ Settings Æ Control Panel Æ System Æ Device

Manger” to check if USB device is installed properly,

3.3 Configure TCP/IP

For Windows 98SE and ME

Step 1: Click Start then Settings and choose Control Panel

Step 2: Double click Network icon. Step 3: Select Configuration tab, then choose TCP/IP from the list of installed network

Components and click Properties button.

Step 4: You can setup the following configurations in two methods:

Option1: Get an IP from Router Automatically

Select the IP Address tab. In this page, click Obtain an IP address automatically radio button.

1) Select Gateway tab and click OK

2) Then, select DNS Configuration tab and select Disable DNS then click OK to finish the configuration.

Option2: Configure IP Manually

1) At IP Address tab, select Specify an IP address, set default IP address for the

Router is 192.168.1.1, so use 192.168.1.X (X is a number betwee n 2 to 254) for IP Address field and 255.255.255.0 for Subnet Mask field.

2) Select Gateway tab and add default Router IP Address “192.168.1.1” in the

New gateway field and click Add.

Under DNS Configuration tab, select Enable DNS and add DNS values (192.168.1.1) in DNS Server Search Order field then click Add.

For Windows 2000

Step 1: (a) Right-click My Network Places and select Properties in the main window

screen

(b) Or, go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections.

Step 2: Right click Local Area Connection (your local network hooked up with ADSL

router) and select Properties:

Step 3: Select Internet Protocol (TCP/IP) then click Properties:

+ 56 hidden pages

Encore ENDSL-A2PLUS4R2, ENDSL-R2PLUS4R2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Descriptions of All Connectors

Descriptions of All Connectors