CEILING RECTANGULAR RACK
PR20A – PR20B – PR20C
If you need assistance, please call 1-877-ENCLUME
Enclume Design Products
24 Colwell Street, Port Hadlock, WA 98339
Enclosed you will find everything needed for the assembly and use of your ceiling rack. Two people make assembly and installation easier. The parts
and hardware included are:
Hardware included:
4 – 3/8” x ½” Button Head Screws
4 – 1 ½” Round Head Rivets
4 – 1 ½” Flat Head Rivets
8 – Push Nuts
4 – 2 ½” Lag Screw
1 – 7/32” Allen Wrench
Toggler Kit
Components included:
1 – Rectangular Base
4 – Hanging Brackets
1 – Grid
6 – Angled Pot Hooks – 13” wide rack
6 – Straight Pot Hooks – 13” wide rack
6 – Angled Pot Hooks – 9” wide rack
6 – Straight Pot Hooks – 9” wide rack
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Rack Assembly
1) If your rack is plated it is best to keep the tissue on during installation to avoid fingerprinting.
2) Locate the four small holes on the long sides of the rectangular base. The rivets, which will support the grid, fit into them. Insert the four flat
head rivets into the small holes closest to the corners of the rectangular base so they protrude into the rack’s interior.
3) Insert the four round head rivets into the small holes in the center of the long sides, again so they protrude toward the interior of the
rectangular base. Looking at each long side, the rivets should be in this order, flathead, roundhead, roundhead, flathead.
4) When you are sure of the order, slide a push nut onto the stem of each rivet and push it toward the rack body so the rivets are locked into
place.
5) Notice that the rivets are positioned closer to one edge of the steel width than the other. Turn the rectangular base so they are closets to the
bottom. This will allow the grid to seat deeply into the rectangular framework, forming a wide lip around the grid.
6) Place the grid into the rectangle.
7) Position the four remaining brackets in front of the four remaining holes, with the rolls down. Using the four button head screws and the Allen
wrench, attach the hanging brackets to the outside of the rectangular base. Straighten the brackets and tighten the screws.
8) We recommend that you anchor your rack into the solid wood of ceiling joists or beams. Carefully measure the area where the rack is to be
hung and install the ceiling screw hooks directly into the wood joists. If it is not convenient to hang your rack directly into wood joists you may
use the new-technology DRYWALL anchors enclosed with your rack. The steel anchors are very strong and when installed in drywall will hold
200 lbs. each. Two anchors hold about 400 lbs. Follow the instructions in the Toggler kit.
9) Distribute the weight of your cookware evenly around the rack.
WARNING: It is important that your ceiling rack is assembled correctly. If the unit is assembled or used incorrectly, it could become unstable and
collapse, possibly causing injury.
LIMITED WARRANTY: This product is warranted to be free of material defects, other than that from normal use, for a period of five years from the
date of purchase. Customer's exclusive remedy shall be the repair or replacement of the defective product and shall be subject to the following
conditions: (1) notice of any defect is received by Enclume within the warranty period and (2) customer returns the defective product to Enclume
Design Products, 24 Colwell St., Port Hadlock, WA 98339, postage prepaid within 20 days following a return authorization number (which may be
obtained by telephoning the number at the top of this instructions) being provided to the customer by Enclume. There are no other warranties,
expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY
DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
Loading...