Photo: BSB1 - BSBB1 base only does not include upper shelf
Bakers Sideboard Base Only
BSBB1
If you need assistance, please call 1-877-ENCLUME
Enclume Design Products
24 Colwell Street, Port Hadlock, WA 98339
Enclosed you will find everything needed for the assembly and use of your Baker’s Sideboard Base. Two people make assembly and
installation easier. Unpack and identify all the parts before you begin.
The parts and hardware included are:
2 – Rectangular uprights with feet attached
1 – Butcher block work surface
1 – Steel trim band
2 – Shelf rims
2 – Grid shelves
4 – ¼ x 7/8” button head screws
20 – 3/8” x ½” button head screws
2 – 2 ½ “ lag bolts
1 – 5/32” Allen wrench (small)
1 – 7/32” Allen wrench (large)
Assembly and Installation Instructions
1) Lay the rectangular uprights side by side on the floor in the correct relationship to one another, about 24” apart.
2) Notice the rivet placement on the shelf rims. When the rims are right side up the rivets are positioned closer to the bottom of
the shelf rim than the top. This positioning allows the grid shelves to seat deeply inside the rim. Slide one of the shelf rims inside
the rectangular uprights. Attach the rim to the uprights using 8 – ½” button head screws. The button heads should be inserted
front to back so the head is visible from the outside of the sideboard. Leave the screws loose.
3) Repeat Step 2 for the second shelf rim.
4) Attach the steel trim band to the outside of the rectangular uprights using the last four ½” button head screws.
5) Stand the base on its feet.
6) Square up the base and tighten all the screws.
7) Slide the grid shelves into the middle and lower shelf rims with the long wires facing upward.
8) Put the butcher block work surface on top of the unit. The back of the board should be flush with the back of the rectangular
uprights. Align the holes on the bottom of the work surface with the slots on the top of the rectangular uprights. Attach the
pieces together with four 7/8” button head screws and the small Allen wrench.
9) We recommend the sideboard be placed tightly against a wall. The two 2 ½” lag screws are for attaching the rack to the wall
should you wish to do so. Four extra holes have been drilled in the back of the steel trim band. The holes are drilled on
16” x 32” centers to match standard wall stud placement. If the positioning of the holes does not match those of your wall studs,
you may drill new holes in the trim to align the rack.
10) The butcher block surface has been penetrated with natural mineral oil. To main the finish, we recommend a periodic application
of mineral oil rubbed into all the wooden surfaces.
WARNING: It is important that your Baker’s sideboard base is assembled correctly. If the unit is assembled or used incorrectly, it could become
unstable and collapse, possibly causing injury.
LIMITED WARRANTY: This product is warranted to be free of material defects, other than that from normal use, for a period of five years from the
date of purchase. Customer's exclusive remedy shall be the repair or replacement of the defective product and shall be subject to the following
conditions: (1) notice of any defect is received by Enclume within the warranty period and (2) customer returns the defective product to Enclume
Design Products, 24 Colwell St., Port Hadlock, WA 98339, postage prepaid within 20 days following a return authorization number (which may be
obtained by telephoning the number at the top of this instructions) being provided to the customer by Enclume. There are no other warranties,
expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY
DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
Loading...