enbrighten 41366, 41369, 41367, 41657 User Manual

Congratulations on your recent purchase of Enbrighten Mini Landscape Lights.
Enbrighten Mini Landscape Lights are designed to provide lighting for life.

IMPORTANT: Before installation, please read all the warning statements included at the bottom

of these instructions.

To ensure proper installation, please follow each step below.

Initial Setup

1. Carefully unpack Enbrighten Mini Landscape Lights from box. Remove and dispose of the
wire ties and plastic bag (see warning on bottom).

2. Locate remote control and install 2 AAA batteries (included).

3. When installing landscape lights outside, a ground-fault circuit interrupter (GFCI)
receptacle must be used. Before installing, plug the landscape lights into the GFCI
receptacle to ensure all lights work properly.

IMPORTANT: Unplug the landscape lights prior to installation.

Installing Landscape Lights

Each landscape light is designed for mounting with the included stakes
(one per light) or for use on a flat surface (see below instructions).

Ground Installation

1. Carefully plan your installation by laying out the
landscape lighting system.

Start with the GFCI receptacle and mounting of

controller. Placement for the first light can be up to
20’ away from the controller. Each subsequent light
can be placed up to 2’ from the previous light.

2. Mount the controller within an appropriate distance for the
polarized plug to reach the receptacle.The controller can be
mounted using the keyholes on the rear of the controller or
the keyhole ear tabs (see figure A). For optimal remote range,

be sure to mount at least 18” o the ground. Do not lay the
controller directly on the ground or where standing water
may accumulate (see figure B). Laying controller on the
ground will significantly reduce remote range.

Keyholes

2in. / 5cm

Seasons

Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.

WARNING: When using outdoor as portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal

injury, including the following:

Ground-fault circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet-location portable luminaire. Receptacles are available
having built-in GFCI protection and are able to be used for this measure of safety.

WARNING: Keep these bags away from babies and children. Do not use in cribs, beds, carriages or playpens. The thin film may cling to nose and mouth and

prevent breathing.

WARRANTY INFORMATION: This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.

RISK OF ELECTRIC SHOCK

• OUTLETS USED FOR POWERING LANDSCAPE LIGHTS
SHALL COMPLY WITH ALL NATIONAL AND LOCAL
ELECTRICAL CODES. CONSULT LOCAL ELECTRICIAN
IF UNSURE OF COMPLIANCE REQUIREMENTS.

• FOR USE ONLY ON GFCI-PROTECTED CIRCUITS.

• DO NOT SUBMERSE.

• DO NOT USE AROUND AQUARIUMS.

• LANDSCAPE LIGHTS ARE A WET-LOCATION
PRODUCT AND HAVE NO SERVICEABLE PARTS.

• DO NOT USE WITH EXTENSION CORD NEAR WATER
OR WHERE WATER MAY ACCUMULATE.

• KEEP LAMPS AT LEAST 16 FEET FROM POOLS

AND SPAS.

• KEEP PLUGS AND RECEPTACLES DRY.

• AVOID DAMAGE TO THE CORDS AND LAMP
ASSEMBLIES DURING INSTALLATION. PERIODICALLY
INSPECT THE LANDSCAPE LIGHTS FOR PHYSICAL
DAMAGE OR OTHER DAMAGE CAUSED BY OUTDOOR
EXPOSURE TO THE ELEMENTS.

• REPLACE ANY DAMAGED LANDSCAPE
LIGHTS.

• DO NOT INSTALL IN LOCATIONS WHERE
LANDSCAPE LIGHTS CAN BE STEPPED ON.

• ENSURE LANDSCAPE LIGHTS ARE
UNPLUGGED FROM POWER DURING
INSTALLATION.

• CHILDREN SHOULD NOT BE ALLOWED TO
PLAY WITH LANDSCAPE LIGHTS.

• UL RECOMMENDS TESTING GFCI CIRCUITS
AND RECEPTACLES EVERY MONTH TO
ENSURE PROPER OPERATION.

RISK OF FIRE

• LANDSCAPE LIGHTS ARE DESIGNED TO
BE MOUNTED WITH THEIR INDIVIDUAL
KEYHOLE MOUNTING FEATURE, DO NOT
MOUNT LANDSCAPE LIGHTS BY USING
THE MAIN ELECTRICAL CORD OR THE
INDIVIDUAL DROP CORDS.

• NOT INTENDED FOR INSTALLATION IN
CEILINGS, SOFFITS, CABINETS, ATTICS OR
OTHER ENCLOSED SPACES.

MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact us at 1-800-654-8483 between 7:00AM—8:00PM CST.
Patents pending | www.enbrightenme.com

Electrical Ratings
Input: 120V, 50/60Hz

Important — please read:

WARNING

41366 41367 41369 41657
Version 1
07/31/2018

Using the Remote

To power on your lights, press the red ON/OFF button located at the top of
the remote. Your Enbrighten Mini Lanscape Lights come paired with
your remote.

NOTE: Keep remote indoors when not being used. Remote is not waterproof.

Now that your lights are installed and powered on, take time to explore the
following settings that are programmable via your remote.

Single-Color Selection Feature

Find your favorite color on the remote’s color pad and simply push
that button to set all of the lights the same color.

NOTE: Within this feature, you can also press the dimming button to adjust
from 10 light levels. The dimming option is only available for single- and dual­color selection.

Dual-Color Selection Feature

1) Press Color 1, then select a color from the color pad to set the color of
every other light starting with the first light.

2) Press Color 2, then select a color from the color pad to set the color of
every other light starting with the second light.

3) During the selection feature, press the dimming button to choose one of 10 light levels.

Tunable White Color Selection Feature

By pressing the white button, cycle through white selections — 2200K, 2700K and 5000K.

Strobe Selection Feature

By pressing the strobe button, the lights will strobe through all of the colors in a random pattern.

Fade Selection Feature

By pressing the fade button, the lights will fade in and out through all of the colors in a random pattern.

Modes Selection Feature

Press the modes button repeatedly to cycle through the following preset modes:

•Twinkle •Multi-Fade •Christmas •St. Patrick’s Day

•Red, White and Blue •Fall •Spring •Multi-Colors

NOTE: Your landscape lights will automatically remember the last customized settings and turn back on in
the same mode and color scheme.

Timer Selection Feature

By pressing the 2-hour timer button, you will activate a two-hour countdown until lights turn o.
By pressing the 4-hour timer button, you will activate a four-hour countdown until lights turn o.

Pair Your Remote with Additional Lights

Your Enbrighten Mini Landscape Lights come with a remote that can be paired to additioal sets
of landscape lights. Additionally, your remote can be paired with Enbrighten Seasons Café Lights
to allow totally customizable Enbrighten lighting.

To pair an Enbrighten pairable remote with landscape lights or pairable Enbrighten Seasons Café lights,
follow the below instructions:

1) Plug in (or supply power) to the lights, and within 8 seconds press and hold the ON/OFF button.
The lights will turn white, blink once and remain white. Your remote and lights are now paired.

a) Please note, you can pair a remote with as many Enbrighten Seasons Lights as you desire

b) Multiple strings can be paired at one time with one remote, by suppling power to multiple

strings at once, then pressing and holding the ON/OFF button within 8 seconds of power
on, per the above instructions.

2) Lights can be paired with up to 8 remotes. If you wish to remove a remote control

from memory of a light (unpair) follow the below instructions:

a) Plug in (or supply power) to the lights, and within 8 seconds, press and hold

the yellow button (in bottom left corner). The lights will turn white, blink twice and remain
white. Your remote and lights are now unpaired.

b) Multiple lights can be unpaired at one time from one remote by suppling power to

multiple lights at once, then pressing and holding the yellow button within 8 seconds of
powering on.

L

a

n

d

s

c

a

p

e

s

L

a

n

d

s

c

a

p

e

s

Ground Mounting

a) Place light directly on ground or garden bedding.

b) Using provided mount stake.You have been provided 1 stake per puck. The stake can

be inserted into the bottom keyhole — make sure the arrow points toward the center
of the light and slide toward the center to lock into place. The stake can then be
inserted into the soil or mulch at the desired angle.The stake has been designed to be
durable in outdoor applications. However, if the stake requires more than a firm push
to be inserted into the ground, loosen soil or remove obstacles, such as rocks,
to ensure the stake is not damaged.

Cord Management

Your Enbrighten Mini Landscape Lights feature burial-grade cable. This allows you to

conceal excess cable by directly burying it in the soil or covering it with garden bedding.

Flat-Surface Mounting

Lay out the landscape system in the manner in which you plan to mount it. Only mount

lights to a solid support structure, such as joist, beams, studs or other sturdy mounting
surfaces. Use one #6 pan head screw (not included) of an appropriate length for the
mounting surface to properly install the lights.

Figure B

Figure A

Questions? Contact us at 1-800-654-8483
between 7:00AM—8:00PM CST.

Do not pull cord tight, leave

slack in loop to prevent

strain on controller.

Best Practices for Installation

•

Install power supply/receiver a minimum of 18” above the ground to ensure optimal range

on remote control.

• Note that placing power supply/receiver directly on ground can severely diminish the
remote control range.

• Do not mount power supply/receiver behind large objects such as posts, walls, large
boulders or other items which may interfere with the signal from the remote control. Also,
avoid mounting the power supply/receiver on or near metal walls or other large metal
objects. Doing so can reduce the remote control’s operation distance.

• Do not pull cords tight as it may damage electrical connections. Leave a small amount of slack on
cords to remove strain on connections.

• Longest remote control operating distances are obtained when the power supply/receiver is in line
of sight of the remote control. Operating the remote control inside of houses and other buildings will
reduce the remote control’s operation distance.

Landscapes

LED Color Changing
Landscape Lights

READ IT OR WATCH IT

Read instructions or watch easy-to-follow video.

Scan QR code or visit https://goo.gl/BPCB68.

ENB / 2 / 32 / 6 /18 / 2 5W

ENB / 2 / 44 / 12 / 18 / 2 10W

ENB / 2 / 68 / 24 / 18 / 2 22W

ENB / 2 / 92 / 36 / 18 / 2 32W

WET

myTouchSmart

Outdoor/Indoor Plug-in Timer

Model #26898

Heavy duty and weather resistant

with two grounded outlets. Fully

customizable time settings.

Easy-to-program custom

settings, presets and countdown

options. On/o switch opens to

reveal program buttons.

Schedule and control outdoor or

indoor lighting from any mobile

or voice-controlled device.

Easy-to-program custom settings,

presets and countdown options.
Self-adjusts to sunset/sunrise times
throughout the year. On/o switch

opens to reveal program buttons.

For addtional stakes and

accessories, visit

www.enbrightenme.com

or call 1-800-654-8483

myTouchSmart

In-Wall Digital Timer

Model #414311

myTouchSmart SunSmart™

In-Wall Digital Timer

Model #33861

myTouchSmart

Outdoor/Indoor Wi-fi Smart Plug

Model #39845

Multiple lengths and styles available now at www.enbrightenme.com

Seasons

Simplify your enbrighten® experience by

automating on and o light times

We recommend the following models, available at select retailers or at www.enbrightenme.com

WARM

VINTAGE LIGHT

2200K

LINKABLE

750ft.

UP
TO

Black cord:

35626 12' / 6 Bulbs

35629 24' / 12 Bulbs

35631 48' / 24 Bulbs

White cord:

35643 12' / 6 Bulbs

35646 24' / 12 Bulbs

35648 48' / 24 Bulbs

WARM

WHITE LIGHT

2700K

LINKABLE

750ft.

UP
TO

Black cord:

31660 12' / 6 Bulbs

33307 18' / 9 Bulbs

31662 24' / 12 Bulbs

31663 36' / 18 Bulbs

31664 48' / 24 Bulbs

White cord:

35604 12' / 6 Bulbs

36803 24' / 12 Bulbs

35608 48' / 24 Bulbs

WARM

VINTAGE LIGHT

2200K

LINKABLE

750ft.

UP
TO

ANY 2 COLOR

COMBINATIONS

DIMMABLE

PRESET

COLOR &

EFFECT

MODES

2 OR 4
HOUR
TIMERS

Black cord:

37791 24' / 12 Bulbs

37790 48' / 24 Bulbs

White cord:

39511 24' / 12 Bulbs

39092 48' / 24 Bulbs

Seasons

™

Classic

Landscapes

LED Color Changing
Landscape Lights

READ IT OR WATCH IT

Read instructions or watch easy-to-follow video.

Scan QR code or visit https://goo.gl/BPCB68.