EMX Industries, Inc. 721H5 Operation Manual

Proximity

Access Control System

721H5

OPERATION MANUAL

Ver. 3.2

Date: 07-05-2001

1

Description

The 721H5 is a self-contained and non -tracking standalone single door Proximity Access Control System . It supports
up to 1000 cardholders. Each cardholder can access the door by using one of the three access modes "Card and PIN

Code", or "Card or PIN Code", or "Card Only". 721H5 reader can be also connected with 721K or 721U Wiegand 26/34
Format Output Read Head to perform an Anti-passback feature, ideal for higher security applications.

There is a 10-digit number in each card, 5 digits in the left called Site Code and 5 digits in the right called Card Code.
Once card is validated, system will automatically assign a group number, from 0 to 47, to it. Cards with same Site Code
are grouped into same group number.

Additional features:
Model 721H5: Connecting with external 721L module, the 701H5 can be performed as On Line Reader.

LED Indicators

LED Status Description

LED GREEN blinking every 1.5 seconds.
LED GREEN on/off moderately
LED GREEN blinking every 0.6 seconds.
LED GREEN on/off fast
LED GREEN on
LED RED on
LED RED on/off fast.
LED RED blinking every 0.4 seconds.

-

-

-

-

-

-

-

-

Power on, in User Mode, normal condition.
System waits for PIN or Function Code inputs completed.
The system is in arming situation.
System is in Edit Mode.
Valid card present or all the successful operations.
Invalid card present or all the fail operations.
The system is busy.
Alarm signal is activated.

Audible Beep

1 short beep

2 short beep
4 short beeps

5 short beeps

-

-

-

-

Key pressed;
Valid card present;
In User Mode , the PIN or Function Code input sequences completed;
In Edit Mode , successful operation.
Invalid card present;
Operation failed.
In User Mode , wait for PIN Code input.
In Registration processing, card has already been registered;
System is disarmed;
Violate anti-passback.

2

Functions Description

Function Description

Door Unlock Time Setting Assign Door Unlock Time (or Door Relay Activated Time). The Door Unlock

Time is keypad programmable and can be programmed as -
Toggle Mode: Latched-on/Latched-off or
Momentary Mode: 1 ~ 600 seconds or 0.1 ~ 39.9 seconds.

Default setting: 2 seconds.

Alarm Time Setting Assign Alarm Time (or Alarm Relay Activated Time). The Alarm Time is

keypad programmable and can be programmed as -

Latched-on Mode or
Momentary Mode: 1 ~ 600 seconds

Default setting: 2 seconds.

Arming Delay Time Setting Once the arming function is set, after a certain period of Arming Delay Time,

the system will enter Arming Mode and 1) the system engages the Timing 2

Sequences if door is close or 2) wait until door is closed to engage the Timing 2
Sequences if door is open. By setting Arming Delay Time, user can have
enough time to go out without activating the alarm system. The Arming Delay
Time is keypad programmable and can be programmed from 1 ~ 600 seconds.

Default setting: 1 second.

Alarm Delay Time Setting When the door is close and the system is in Arming Mode, open the door will

activate the alarm relay after a certain period of delay time (Door Unlock Time
+ Arming Idle Time + Alarm Delay Time). To avoid the alarm generated, user
can close the door within "Door Unlock Time + Arming Idle Time" delay period
and system is still in Arming Mode, or just enter disarm process within "Door

Unlock Time + Arming Idle Time + Alarm Delay Time" period and system is in
Disarming Mode. The Alarm Delay Time is keypad programmable and can be

programmed from 1 ~ 600 seconds.
Default setting: 3 seconds.

If door is opened and in Latched-off mode, the delay time is infinite and there
will be no alarm activated.

Arming Idle Time Setting This idle time can provide user an enough time to close the door without

entering Alarm Delay Time period. Once system enters Alarm Delay Time
period, the user has to disarm the system to avoid the alarm generated. The
Arming Idle Time is keypad programmable and can be programmed from 1 -
600 seconds.
Default setting: 15 seconds.

Power on Arming After power on, the arming is set automatically and system enters Time 1

Sequence. This feature is keypad programmable. Please refer to Command 20.
Default setting: Disable power on Arming.

Door Monitored & Re -lock To prevent "tailgating", door is monitored and automatically locked when entry is

completed and door is closed for at least 2 seconds.
This feature is keypad programmable and isn't effective if the Door Unlock
Time setting is in Latched-on mode. Please refer to Command 20.
Default setting: Disable Auto Re-lock function.

Door Exit Release A door exit push-button or infrared detector to unlock the door from inside.

This feature is keypad programmable. Please refer to Command 20.
(Note: Push-button switch or infrared detector is not included).
Default setting: Enable Door Exit Release function.

Audible output Audible beep sound to indicate the status of key pressed or successful operation

or operation failed.

Edit Mode Timeout If no entry is made within 30 seconds, the system will exit the Edit Mode and

return to its normal operation, i.e. User Mode.

Keypad Automatic Blocking Keypad will be locked for 30 seconds if wrong key -entries are made 3 times in

User Mode. A valid or invalid card can release the keypad from blocking during
these 30 seconds.
For all the valid inputs, either by cards or by keys, the error counter will reset to

0.
For the invalid card input, the error counter will reset to 1.

3

Forced Open Alarm If door is forced open, Alarm Relay will be activated. Refer to Command 28.
PIN Code Changeable Cards with "Card and PIN Code", or "Card or PIN Code" access mode can

change the PIN Code in User Mode by just press new PIN Code twice followed
with # sign in 3 seconds after access is successful.

Tamper Protection A built-in tamper switch (C, NC, NO) to prevent the reader from removing.
Arming/Disarming The designated door can be armed or disarmed.

Arming can be reset by either entering the Edit Mode or the disarm process.

Anti-passback 721H5 reader can be connected to 721K or 721U read head to per

form

Anti-passback feature. Individual card can access the reader in an anti-passback
manner only when it is selected to have an anti-passback function by

Command

26 and also the reader is defined to have anti-passback feature by

Command

20.
Default setting: Disable Anti-passback function.

Non-volatile EEPROM Will save all of the codes and system parameters when power is off.
Alarm LED and Alarm Reset Alarm LED and Alarm, if it is still activated, can be reset by entering the Edit

Mode, or by entering the disarming process.

System Programming Guide

Commands Description

*

PPPPPP# or follow step 1 & 2

1. Present card with address
#00000 to the reader, and input PIN
Code and # sign if the card is in
"Card and PIN Code" access
mode. 2. Press # key in 3 seconds.

PPPPPP= 6-digit Password.

Either way can enter Edit Mode.

Default setting: PPPPPP= 123456.

*

# or **# Either way can exit Edit Mode and then in User Mode , however **# will also

set the arming.

00*NNN# Assign a Reader Number 001 ~ 254 to itself.

If NNN=000 or NNN> 254, system will assign a default setting.
Default setting: NNN= 001.

02*TTT# Door Unlock Time Setting. Forever or 1 ~ 600 seconds or 0.1 ~39.9 seconds.

Toggle Mode : TTT= 000 for forever.
Momentary Mode : TTT= 001 ~ 600 for 1 ~ 600 seconds.
TTT= 601 ~ 999 for 0.1 ~ 39.9 seconds. (TTT – 600) x 0.1
Default setting: TTT= 002

03*TTT# Alarm Time Setting. Forever or 1 ~ 600 seconds.

Latched-on Mode : TTT= 000 for forever.
Momentary Mode : TTT= 001 ~ 600.

If TTT>600, system will assign a default setting.
Default setting: TTT= 002

05*TTT# Arming Delay Time Setting. 1 ~ 600 seconds.

TTT= 001 ~ 600.

If TTT>600, system will assign a default setting.
Default setting: TTT= 001

06*TTT# Alarm Delay Time Setting. 1 ~ 600 seconds.

TTT= 001 <-> 600.

If TTT>600, system will assign a default setting.
Default setting: TTT= 003

09*NNNNNNnnnnnn# Change Edit Password. User has to enter new password twice.

NNNNNN: new password, 000000 ~ 999999.
nnnnnn: new password, 000000 ~ 999999.

10*SSSSS*EEEEE# Disable the proximity cards with addresses starting from SSSSS to EEEEE.

After disabled, the cardholder(s) can't access the system.

4

SSSSS: 00000 ~ 00999
EEEEE: 00000 ~ 00999
If SSSSS>EEEEE or SSSSS>00999 or EEEEE>00999, error message.

10*SSSSS9EEEEE# Delete the proximity cards with addresses starting from SSSSS to EEEEE

from

system.

SSSSS: 00000 ~ 00999
EEEEE: 00000 ~ 00999
If SSSSS>EEEEE or SSSSS>00999 or EEEEE>00999, error message.

11*SSSSS*EEEEE# Enable the proximity cards with addresses starting from SSSSS to EEEEE. After

enabled, the cardholder(s) can access the system by using "Card Only" mode.
SSSSS: 00000 ~ 00999
EEEEE: 00000 ~ 00999
If SSSSS>EEEEE or SSSSS>00999 or EEEEE>00999, error message.

12*SSSSS*PPPP# Enable a proximity card with addresses SSSSS and assign a PIN Code PPPP

to it. After assigned, the cardholder can access the system by using "

Card or

PIN Code " mode. For example:

After entering 12*00005*7766#, user can access the door by just either
‘presenting the card with address #00005 to the reader’ or “entering the address

no. 00005 and then 7766#.

SSSSS: 00000 ~ 00999
PPPP: 0001 ~ 9999
If SSSSS>00999, error message.

13*SSSSS*PPPP# Enable a proximity card with addresses SSSSS and assign a PIN Code PPPP

to it. After assigned, the cardholder can access the system by using " Card and
PIN Code " mode. For example:

After entering 13*00005*7766#, user can access the door by just presenting
the card with address #00005 to the reader and then entering 7766#.

SSSSS: 00000 ~ 00999
PPPP: 0001 ~ 9999
If SSSSS>00999, error message.

17*FFFF# Assign 4-digit Function Code FFFF.

Function Code followed with <#> to Arm or Disarm the system.
Function Code followed with <DEV> to activate the Alarm Relay.
FFFF: 0001 ~ 9999
Default setting: FFFF= 1234

18*TTT# Arming Idle Time Setting. 1 ~ 600 seconds.

TTT= 001 ~ 600.

If TTT>600, system will assign a default setting.
Default setting: TTT= 015

19*SSSSS*NNNNN# Register a number of card(s) to the system. After registered, the cardholder can

access the system by using "Card Only" mode. Note: Cards can not be

registered through 721K or 721U.
SSSSS: 00000 ~ 00999. Register Card(s) with addresses starting from SSSSS.
NNNNN: Indicate a number of card(s) to be registered.

If NNNNN= 00001 Single card registrat ion.
Card Codes can be either in sequential or in random, after # sign, user can

register the proximity cards to the system by present the cards to the reader
panel one by one continuously. For each valid card registration, the system will
automatically as sign a group number to each card and increment the address by
one. Before each registration, system will also perform the following checking: A

card registered can not be registered again, five beep tones are generated
to indicate this error.

If NNNNN= 00002 – 00999 Block registration.
If Card Codes are in sequential with same Site Code, after # sign, user can
register the proximity cards to the system by just present the card with the
lowest Card Code to the reader panel. The system will automatically assign a
group number and the addresses starting from SSSSS to the proximity cards.

System will refuse the block registration if card(s) is (are) registered
before, five beep tones are generated to indicate this error. Cards have
already been registered in these block addresses will be overwritten.

Cards with same Site Code are automatically assigned to same group number

5

even it is not registered at the same time.

If NNNNN=00000, error message.
If NNNNN>available addresses, system will assign all the available addresses
and then quit.

20*NNN# System parameters setting.

Auto Re -lock: disable value 000; enable value 002
Power on Arming: disable value 008; enable value 000
Door Exit Release: disable value 000; enable value 016
Anti-passback: disable value 000; enable value 128

NNN: 000 ~ 255

For example:
Auto Power on Door Exit Anti-
NNN Re-lock Arming Release Passback
000 disable enable disable disable
002 enable enable disable disable
008 disable disable disable disable
010 enable disable disable disable
016 disable enable enable disable
018 enable enable enable disable
024 disable disable enable disable
026 enable disable enable disable
128 disable enable disable enable
130 enable enable disable enable
136 disable disable disable enable
138 enable disable disable enable
144 disable enable enable enable
146 enable enable enable enable
152 disable disable enable enable
154 enable disable enable enable

If NNN>255, system will assign a default setting.
Default setting: NNN= 024

26*SSSSS*EEEEE*X# Define the proximity cards with addresses starting from SSSSS to EEEEE.to

have or not to have an anti-passback feature. For example:
If enter 26*00005*00008*1#, cards with addresses from 5 ~ 8 do not have

anti-passback feature.
If enter 26*00005*00008*0# & 26*00005*00008*2#, cards with addresses

from 5 ~ 8 have anti-passback feature. The first entry can be made through
either 721H5 or 721K/721U.

SSSSS: 00000 ~ 00999
EEEEE: 00000 ~ 00999
X: 1-disable anti-passback; 0- enable anti-passback;
2- enable first entry can be made through either 721H5 or 721K/721U.
If SSSSS>EEEEE or SSSSS>00999 or EEEEE>00999, error message.

28*NNN# Disarming Forced Open parameter setting.

NNN: 000 – Without Forced Open feature in Disarming mode.
NNN: 128 – With Forced Open feature in Disarming mode.

Default setting: NNN= 000

29*29*# Delete all the proximity cards and all the Group Numbers.