Firmware
Update Manual
for Emulex® Adapters
P003603-01A Rev A Critical Connectivity Solutions
TM
Copyright© 2007–2008 Emulex. All rights reserved worldwide. No part of this document may be reproduced by any
means or translated to any electronic medium without the prior written consent of Emulex.
Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by
Emulex for its use; or for any infringements of patents or other rights of third parties which may result from its use.
No license is granted by implication or otherwise under any paten t, copyrigh t or rela ted ri ghts of Emulex .
Emulex, AutoPilot Installer, BlockGuard, cLAN, FabricStream, FibreSpy , Giganet, HBAnyware, InSpeed, IntraLink,
LightPulse, MultiPulse, SAN Insite, SBOD and Vixel are registered trademarks, and AutoPilot Manager, Critical
Connectivity Solutions, EZPilot, SLI and VMPilot are trademarks of Emulex. All other brand or product names
referenced herein are trademarks or registered trademarks of their respective companies or organizations.
Emulex provides this manual “as is” without any warranty of any kind, either expressed or implied, including but not
limited to the implied warranties of merchantability or fitness for a particular purpose. Emulex may make
improvements and changes to the product described in this manual at any time and without any notice. Em ulex
assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties that may
result. Periodic changes are made to information contained herein; although these changes will be incorporated into
new editions of this manual, Emulex disclaims any undertaking to give notice of such changes.
Emulex, 3333 Susan Street
Costa Mesa, CA 92626
Firmware Update Manual Page ii
Table of Contents
Introduction.............................................................................................................. 1
Compatibility......................................................................................................1
Prerequisites .....................................................................................................1
Things to Know Before You Download .............................................................. 1
Update Utilities ........................................................................................................2
Firmware Update Manual Page iii
Introduction
Compatibility
For information about any firmware release, see the readme.txt file that accompanies the firmware. Such
information includes compatibility, cautions and warnings, known issues and files included in the
release.
This manual does not contain the procedures themselves. It serves as a guide to the publication th at
contains the procedures you need.
Prerequisites
• Local boot disk.
• The intended Fibre Channel target should be big enough to hold all system files and th e swap
slice of the current local boot disk.
Things to Know Before You Download
• Firmware differs between adapter models. Make sure you download the appropriate firmware for
your adapter.
• Before you download the files, create a directory into which you can download and unzip them.
• As a measure of protection, ensure that critical files on your local boot disk are ba cked up .
• Depending on the release, the firmware kit contains either a .all file or a .awc file that updates
the kernel if the existing kernel is an earlier version. If the update process is interrupted (such as
by a power outage) and the kernel is being updated, you may have to return the adapter to
Emulex for repair.
• Firmware may be bundled with or without boot code. Boot code allows you to designate a Fibre
Channel drive as the boot drive. If the adapter’s devices will be used to boot the system, Emulex
recommends that you use the firmware package that includes boot code, if one is provided. If
you select a firmware image that includes boot code, the update proce dure will loa d both the
new firmware and boot code at the same time. After updating, refer to the b oot code manual for
procedures on enabling the boot code on your adapter.
• If you are currently using an Emulex driver, you can update firmware with the management
application that was loaded when the driver was installed.
Firmware Update Manual Page 1
Update Utilities
Emulex offers a variety of utilities that you can use to update the adapte r firm ware . The utilities that yo u
can use depend on your operating system and, in some cases, driver:
Operating System
Windows X X X
Linux X X X
VMware X
Solaris (LPFC driver) X X
NetWare X
EFI X
a. Use HBAnyware for CEE firmware update. Do not use the offline utilities
b. FC Port driver only
HBAnyware
a
elxcfg
b
lputil
EFI
Utility
Offline
Utilities
After you decide which utility to use, see the appropriate update procedure:
• HBAnyware utility: See the HBAnyware Utility User Manual
• elxcfg utility: See the FC Port Driver User Manual
• lputil utility: See the lputil Utility for Linux and Solaris User Manual
• EFI utility: See the Boot Code User Manual
• Offline utilities (doslpcfg, winlpcfg, linlpcfg): See the Offline Utilities Manual
Firmware Update Manual Page 2
Loading...