Emtek EMTouch Installation & Programming Manual

ASSA ABLOY, the global leader in door opening solutions

Installation & Programming Guide

EMTouch™ Electronic Lever Locksets

2

ITEM NO. DESCRIPTION QTY.

1 Key 2

2 Outside Trim Plate Assembly 1

3 Adjustable Latch for 2 ⁄” or 2 ¾” Backset 1

4 Inside Trim Plate Assembly 1

4a Inside Chassis 1

4b Inside Trim Plate 1
4c #8-32 x ⁄" Flat Head Machine Screw 2

4d 9V Alkaline Battery 1

5 #8-32 x 1½" Flat Head Machine Screw 2

6 #8 x ¾" Wood Screw 4

7 Strike Plate 1
8 Plastic Extender 1

9 Plastic Latch Pin 1

3

4b

2

4a

4c

4d

5

7

6

4

8

9

1

6

What’s in the Box

3

1” Deep,
1” Diameter
Edge Bore

2 ⁄” or 2 ¾” Backset

2 ⁄” Diameter Bore

⁄” Deep

2 ¼”

1 “

1” Diameter Edge Bore

3. Remove Screws from Inside Trim Plate

2. Door Prep

3. Door Jamb Prep

1. Conrm Handing

HANDING OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE

Hinge is on the left.

Door is Left Hand (LH).

Hinge is on the right.

Door is Right Hand (RH).

Hinge is on the right.

Door is Right Hand (RH).

Hinge is on the left.

Door is Left Hand (LH).

In-Swing Doors

Out-Swing Doors

outsideoutside

Preparation

⁄” Deep

1-1/8"

2-3/4"

2 ¼”

1 ½”

Fasten Strike Plate using two #8 x ¾”
Wood Screws (item #6).

4. Install Strike Plate

4

Use a Phillips head screwdriver to remove screws (item #4c) shown below and
detach Inside Trim Plate from the Inside Chassis.

Fasten Adjustable Latch using two #8 x ¾” Wood Screws (item #6).

2. Remove Screws from Inside Trim Plate

How to Install

!

!

REMOVE INSIDE
CHASSIS FROM
TRIM PLATE BEFORE
INSTALLING THE
OUTSIDE TRIM.
THUMBTURN MUST
BE IN NEUTRAL
POSITION.

To remove Pin:
Push Plastic Latch Pin (item #9)
through latch with screwdriver.

The Adjustable Latch is factory
shipped with a 2¾” backset
position. Remove pin and slide
spindle hub forward for a 23/8”
backset, then reinsert the pin in
the hole at the back of the latch
as shown.

1. Install Adjustable Latch

LH RH

See Page 3 for Handing
Information.

Scan QR code for

installation video

Plastic Latch Pin

Plastic

Latch

Pin

5

3. Install Outside Trim Plate Assembly

Step 1: While holding Outside Trim Plate Assembly, Press the Plastic Extender (A) into
end of Spindle Shaft (B). The Shaft is properly aligned when the marking ‘TOP’ can be
seen from an overhead view.

Step 2: Position the Outside Trim Plate Assembly through the bore hole.

Step 3: With the Outside Trim Plate Assembly ush to the door, REMOVE the Plastic

Extender.

Feed wire harness
through the bore hole.

B

!

A

Fit Plastic Extender
through latch.

ONCE POSITIONED,
OUTSIDE TRIM PLATE
ASSEMBLY REQUIRES
SUPPORT.

THIS SIDE ON TOP.

!

6

4. Install Inside Chassis

CAM LINK MUST
REMAIN IN
THE CORRECT
POSITION DURING
INSTALLATION.

!

Step 1: Conrm the position of Cam Link.

For Left Hand Locks:

Turn to left position.

For Right Hand Locks:

Turn to right position.

Step 2: Feed the Wire Harness through Inside Chassis.

7

CHECK ALIGNMENT BEFORE
FULLY TIGHTENING SCREWS.

!

Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B).

A

B

Step 5: Install Battery.

For optimal performance, always use a good quality battery.

9V Battery

Step 3: Fasten Inside Chassis using two #8-32 x 1½”
Flat Head Machine Screw (item #5).

8

5. Install Inside Trim Plate

Screws (item #4c)

Fasten Inside Trim Plate using two #8-32 x ⁄” Flat Head Machine Screws
(item #4c).

*Neutral position is required for installation and removal of the Inside
Trim Plate Assembly.

(Does not apply to Keypad Storeroom/Gate product)

!

USER CODES ARE LOCATED
ON THE INSIDE TRIM PLATE &
ON PAGE 11.

Inside

Correct position for
installation.Thumbcam
must be positioned as
shown (Neutral Position)*

!

Scan QR code for

installation video

9

Your Emtek lock is shipped with two 4-digit user codes and a 6-digit
programming code. These codes are randomly generated at the factory.

(Turn to next page for Programming Instructions.)

To Unlock:

1. Press EMTEK key or touch

3 ngers across screen.

2. Enter 4-digit user codes.

(See sticker located on the inside

trim plate or on page 11).

3. Turn Handle.

To Lock:

1. Rotate Thumbturn from inside.

Passage feature

(Does not apply to Keypad Storeroom/Gate product)

Activate by turning the inside thumbturn to the unlocked position.
This will engage the outside lever so a code is not required to enter.

Your Lock is Ready to Use

How to Use

Locked Unlocked

1

2

3

10

In order to perform each of the following six functions, the lock must rst be
placed in Programming Mode:

*If no input within 20 seconds, Yellow LED goes out, Red LED ashes and lock exits Programming Mode.

1. Press and hold EMTEK button for 3 seconds

2. Yellow LED ashes, then remains solid*, number keys also illuminate

3. Enter Programming Code

4. Yellow LED ashes, then 2 beeps

5. Yellow LED remains solid (awaiting button press; see following Table)

If you wIsh to Press

Button

ActIons IndIcAtors

Change

Programming

Code

(6 digits)

1

Enter New

Programming

Code

(6 digits)

Re-Enter

New

Programming

Code

(6 digits)

• 1 Green LED ash

• 1 beep

• 1 Green LED ash

• 1 beep

• 2 Green LED ashes

• 2 beeps

Add User Code

(4 digits)

(Store up to 20

User Codes)

2

Enter New
User Code

(4 digits)

Re-Enter

New User

Code

(4 digits)

• 1 Green LED ash

• 1 beep

• 1 Green LED ash

• 1 beep

• 2 Green LED ashes

• 2 beeps

Delete User Code 3

Enter User

Code to be

Deleted

Re-Enter

User Code to

be Deleted

• 1 Green LED ash

• 1 beep

• 1 Green LED ash

• 1 beep

• 2 Green LED ashes

• 2 beeps

**

Enable/Disable

All User Codes

4

Entering ‘4’ disables all Users

(enables all if disabled)

• 2 Green LED ashes

• 2 beeps

Delete All User

Codes

5

Re-Enter Programming Code

• 1 Green LED ash

• 1 beep

• 2 Green LED ashes

• 2 beeps

Turn Beeper On/

Off

6

Entering ‘6’ turns OFF (or ON)

• 1 Green LED ash

• 1 beep

• 2 Green LED ashes

• 2 beeps

**Also referred to as “vacation mode”. This command temporarily disables all user codes (metal key
override will still work).

How to Program

Programming Your Lock

11

IN8-EMTOUCHLL 10/22/2012

Restoring the Lock to Factory Default Setting

• Press and hold EMTEK button for 3 seconds.

• Enter

“000000”

• After 2 beeps and 2 Green LED Flash, remove power (disconnect 9V battery)

from Lock.

• After 5 seconds, restore power (reconnect 9V battery)

• Conrm by 2 beeps and 2 Green LED Flash.

This procedure clears the lock of all users and restores the Programming Code and

2 User Codes shipped with the lock.

Function Indicators

Valid Code • 1 short beep, EMTEK button ashes

Green.

Invalid Code/Access Denied* • 1 Red LED ash

• 2 short beeps

Lock-Out Mode Error • 2 short beeps

• 1 short beep per second for duration

Access Accepted • 1 short beep

• 1 Green LED ash

Low Battery • 4 Red LED ashes

• 4 short beeps

Blackout Battery

**

• 1 long Red LED ash

• 4 long beeps

Button Press Accepted • 1 Yellow LED ash

• 1 Short Beep

Outside Thumb Turn Enabled • 2 Green LED ashes

* If 3 consecutive incorrect codes are entered, the lock emits 4 short beeps and a ashing Red EMTEK

button. The lock will not accept additional input for 20 seconds (20 beeps). When the next valid code is
entered the lock will beep quickly 3 times to alert of the incorrect codes.

**

Battery voltage has dropped too low; keypad will be disabled but metal key override will still work.

Keypad Operation - Beeper & LED Indicators

Place Sticker Here

U.S. patent: 8,176,761
International patents pending.

ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and
convenience.

Copyright © 2012, Emtek Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part
without the express written permission of Emtek Products, Inc. is prohibited.

Scan QR code for
installation video