Emtek CF Mechanism Passage Privacy Locksets User Manual
How to Install
5. Install Trims (Continued)
Step 6: Secure rosette to door with Ring Fastener H using Plastic
Ring Fastener Wrench N.
Check trim alignment before fully tightening
!
Ring Fastener.
Ring Fastener H
Plastic Ring
Fastener
Wrench N
Step 7: A. Place Plastic Washer I on to Knob or Lever J. B.Then
install Knob or Lever J by sliding it on to the spindle.
Plastic Washer I
A
CF Mechanism
Passage & Privacy Locksets
Installation Guide
B
Step 8: A. Tighten the pre-installed set screw in knob or lever with
3/32” Allen Wrench O. B. Screw Privacy Pin G through interior trim
into latch.
Privacy Pin G
A
B
ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs
for security, safety and convenience.
Copyright © 2013, Emtek Products, Inc. an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Emtek Products, Inc.
is prohibited.
What’s in the Box
ITEM NO. DESCRIPTION QTY.
Pre-Assembled Trim
Plastic Alignment Tool
Concealed Fastener Mechanism
#8-32 x 1” Flat Head Machine Screws
Rosette
Privacy Pin
Ring Fastener
Plastic Washer
Interior/Exterior Knob or Lever
#8 x 3/4” Wood Screws
Latch
Strike Plate
Plastic Ring Fastener Wrench
3/32” Allen Wrench
ASSA ABLOY, the global leader in door opening solutions
1
1
1
2
1
1
1
1
1
4
1
1
1
1
Preparation
How to Install
1/8” Deep
2 ¼”
1 “
2. Door Jamb Prep
1/16” Deep
2 3/8” or 2 ¾”
Backset
2 1/8”
Diameter
Bore
1” Diameter
Edge Bore
1” Diameter
Edge Bore
4. Install Latch1. Door Prep
Step 1: Place Plastic Alignment tool
in bore hole.
Alignment Tool C
Step 2: Insert & fasten Latch L using two
#8 x ¾” Wood Screws K.
IF NECESSARY, ROTATE LATCH
!
NOSE SO CURVED FACE WILL HIT
THE STRIKE PLATE WHEN THE
DOOR IS CLOSING.
5. Install Trims
Step 1: Install Pre-Assembled Trim B.
Incorrect
Correct
Make sure the release hole is close to door
!
edge (applicable only to privacy function).
Step 2: Install Concealed Fastener Mechanism
D with arrow pointing to door edge.
Check trim alignment before
!
fully tightening screws.
#8-32 x 1”
Machine Screws E
Step 4: Insert short end of 3/32” Allen Wrench O
into spindle as indicated and tighten
approximately one full rotation.
3/32” Allen Wrench O
1 ½”
1-1/8"
3. Install Strike Plate
Fasten Strike Plate using two
#8 x ¾” Wood Screws .
2-3/4"
2 ¼”
Threaded hole must
face the side of
the door where the
privacy pin will be
installed (only for
privacy function).
Arrow points to
door edge.
Step 3: A. Fully extend spindle by pulling it
outwards until it is against the internal stop.
B. Tighten the pre-installed set screw in knob
or lever with 3/32” Allen Wrench O.
A
B
Set screw factory
installed inside the
spindle must be
tighten approx.
one full rotation.
Step 5: Install Rosette F.
Rosette F
Make sure the
release hole is
close to door edge
(applicable only to
privacy function).
REV. 05/06/2013
Loading...