Emprex SPX10 User Manual

Portable Speaker Phone

User’s Guide

Version 1.0

Introduction and Features

System Requirement

• Pentium 4/Celeron, AMD 1GHz or faster

processor, minimum 256MB RAM

• Microsoft Windows ME/2000/XP/Vista series

• USB compatible

2. Click the “Speaker Phone Driver” icon to install
device driver.

3. Select “User Guide” to know more about detail
setting.

Settings

Audio setting

1. To use this device, you will need to have
Microsoft Windows ME/2000/XP/Vista
installed on your computer.

2. To use this device for internet
communication, you must have a
broadband internet connection and
applicable software which supports audio
calls (such as Skype) installed properly on
your computer.

3. You can verify and adjust the audio settings
by following these steps:

i. In the Windows Start menu, go to Control

Panel

ii. Select the Sound and Audio device icon
iii. In the Audio tab, click on the volume button, a

Volume Control

iv. You can adjust the volume of the microphone

and speaker by using the control buttons
located at the front of the unit directly.

Tips

1. If you cannot hear any sound from the unit,

close all your current applications. Select

Æ Control Panel ->Sounds and Audio
devices -> Audio -> then select “C-Media

USB audio Device” as the default Windows
Audio device for both sound playback and

sound recording.

screen appears

Start

2. For stereo sound of audio playback or

private conversation, stereo headphones
can be plugged into 3.5mm stereo
headphone jack located on the side of the
unit.

FCC Certification

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, received,

including interference that may cause undesired

operation.

Note:

This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency, energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

-

- Consult the dealer or an experienced radio/TV
technician for help.

- Increase the separation between the equipment
and receiver.

- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

CAUTION

Any changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.

FOR EUROPE

“The unit is in conformity with the EMC
directive and low-voltage directive.”

Package Contents

• Portable Speaker Phone with USB cable

• Setup Installation and Software CD

• User Guide

Getting started

You will need to install the drivers and application
software in the included CD before

Do not connect your new unit to your computer before
installing the drivers.

Tips

If you accidentally begin installation with your unit connected
and the Add New Hardware Wizard or Found New

Hardware Wizard dialog box appears, click the Cancel tab.

Installation Steps:

1.

Insert the Installation CD into your CD-ROM
drive. The installation program should start
automatically. Follow the on-screen
instructions to finish up the installation.

connecting the unit.

2. To check volume settings or when there is no

sound from the unit, repeat step 1) above to
select Sounds and Audio devices -> Volume

-> make sure that “Mute” check box is not
checked. When you select Advanced button, a
“

Volume Control

adjust volume up or down accordingly.

3.

To check microphone settings, bring up the
“Volume Control” screen, click Advanced
button and select Options -> Properties ->
Adjust volume for -> Recording.

4. Make sure “

OK, there will be a new Advanced button.
Select “Options -> “Advanced Controls ->
Other Controls”. Make sure that “
checked.

5. If your unit’s LED changes from “blue” to “red”

color, it is in mute

“Microphone Mute”

and the LED will change back to “blue” again.

” screen pops-up. You may

Recording

” is checked and click

recording state. Press the

button on your unit once

AGC

” is not

Useful information

1. Connect your Speaker Phone directly to

the available USB port. Using an
extended cable or USB hub device is not
recommended.

Disclaimer

Information in this document is subject to change
without notice. The manufacturer does not make any
representations or warranties (implied or otherwise)
regarding the accuracy and completeness of this
document and shall in no event be liable for any loss
of profit or any other commercial damage, including
but not limited to special, incidental, consequential,
or other damages. No part of this document may be
reproduced or transmitted in any form by any means,
electronic or mechanical, including photocopying,
recording or information recording and retrieval
systems without the express written permission of
the manufacturer.

WEEE LOGO

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European
countries with separate collection systems)

All trademarks and logos belong to their respective
owners.

3100554010 Version 1.0 July 2007

Configuration système requise

• Pentium 4/Celeron ou AMD 1GHz ou

processeur plus rapide, 256MB RAM
recommandés.

• Compatible Microsoft Windows

ME/2000/XP/Vista

Étapes d'installation :

1. Insérez de CD d'installation le dans lecteur le

CD-ROM. Le programme démarre
d'installation automatiquement. Suivez les
instructions à l'écran pour terminer
l'installation.

Requisiti del sistema

• Processore Pentium 4/Celeron ed AMD 1GHz

o più potente; 256MB di RAM raccomandati.

• Compatibile con Microsoft Windows

ME/2000/XP/Vista

Fasi d'installazione:

1. Inserire il CD d'installazione nell'unità CD-

ROM. Il programma d’installazione dovrebbe
avviarsi automaticamente. Seguire le istruzioni
su schermo per completare l'installazione.

Requisitos do sistema

• Processador Pentium 4/Celeron e AMD de 1

GHz ou acima, 256 MB de RAM recomendado.

• Compatível com o Microsoft Windows

ME/2000/XP/Vista

Instalação:

1. Introduza o CD de instalação na unidade de

CD-ROM. O programa de instalação inicia
automaticamente. Siga as instruções no ecrã
para concluir a instalação.

2. Cliquez sur l'icône “Speaker Phone Driver

(Pilote du haut-parleur téléphonique)” pour
installer le pilote du périphérique.

3. Sélectionnez “User Guide (Guide d'utilisation)”

pour en savoir plus sur les réglages détaillés.

Systemanforderungen

• Pentium 4/Celeron und AMD 1GHz oder noch

schnellere CPU, 256MB RAM empfohlen.

•

Microsoft Windows ME/2000/XP/Vista ­kompatibel

Installationsschritte:

1. Legen Sie die Installations-CD in Ihr

optisches Laufwerk ein. Das
Installationsprogramm wird automatisch
gestartet. Folgen Sie den
Bildschirmanweisungen, um die Installation
fertig zu stellen.

French

2. Fare clic sull’icona “Speaker Phone Driver”

(Driver vivavoce) per installare il driver.

3. Selezionare “User Guide” (Guida dell’utente)

per altri dettagli sulle impostazioni.

Requisitos del Sistema

• Recomendado Pentium 4/Celeron y

procesador AMD 1GHz ó superior, 256MB
RAM.

• Compatible con Microsoft Windows

ME/2000/XP/Vista

Pasos de la Instalación:

1. Inserte el CD de Instalación en su unidad

CD-ROM. El programa de Instalación
debería comenzar automáticamente. Siga
las instrucciones de la pantalla para
finalizar la instalación.

Italian

2. Clique no ícone “Speaker Phone Driver”

(Controlador do altifalante) para instalar o
controlador do dispositivo.

3. Seleccione a opção “User Guide” (Guia do

utilizador) para obter mais informações.

Systeemvereisten

• Pentium 4/Celeron en AMD 1GHz of snellere

processor, 256MB RAM aanbevolen.

• Compatibel met Microsoft Windows

ME/2000/XP/Vista

Installatiestappen:

1. Plaats de installatie-cd in het cd-romstation.

Het installatieprogramma zou automatisch
moeten starten. Volg de richtlijnen op het
scherm om de installatie te voltooien.

Portugese

2. Klicken Sie auf das "Speaker Phone Driver

[Lautsprechertelefontreiber]"-Symbol, um den
Gerätetreiber zu installieren.

3. Wählen Sie "User Guide

[Bedienungsanleitung]" für Details zur
Einstellung.

German

2. Haga clic en el icono “Speaker Phone Driver”

(Controlador de Teléfono Altavoz) para
instalar el controlador del dispositivo.

3. Selecciones “User Guide” (Guía del Usuario)

para saber más sobre los detalles de la
configuración.

Spanish

2. Klik op het pictogram “Speaker Phone Driver”

(Stuurprogramma luidsprekertelefoon) om het
apparaatstuurprogramma te installeren.

3. Selecteer "User guide" (Gebruikershandleiding)

voor meer details over de instellingen.

Dutch