Emprex D250PE Quick Start Manual

Version 1.0 Sep. 2007

1 GENERAL INFORMATION

This Secure Drive Enclosure kit package contains:

• HDD Enclosure

• USB-Y cable

• Software, Driver and Manual CD

• Quick Start Guide

• Pouch

• Screws / Screwdriver (for applicable models only)

2 GETTING STARTED

Hardware Installation

Assembling your hard drive to the Enclosure kit

Note: The pictures are only for illustration and actual accessories may

differ from picture.

3 SETTING UP

Security Software Setup

1. Insert the Installation CD into your CD-ROM drive.
Select “Software & Win98 driver”.

2. When this screen appears,

For Windows 98/SE:

Select “Install Win98 Driver” before proceeding to next
step.

For Windows XP/Me/2000/Vista

Select “Configure to Secure Drive”.

Caution:

Configuring to Secure Drive destroys any existing data. Be sure to
back up the disk contents first.

3. When this screen appears, follow the on-screen instructions.

1) Enter【New Password】

2) Re-enter【Confirm New Password】

3) At【Hint】prompt, enter a suitable phrase to help you recall

your password later on.

4) Click【Prepare Secure Drive】

4.

When the installation is complete, please re-connect the USB
drive into the computer’s USB port for the new configuration to
take effect.

Note: In order to remove the device to take effect, you could choose either

device’ end or computer’s end (USB Y cable) to unplug and re-plug
the USB cable. Otherwise, system will still show the old data in the
drive.

1. Turn to the rear side and remove
the rear case. Align the hard
drive’s interface connector to the

on-board connector.

2. Gently lower the hard
drive till it rests flat
against the board.

3. Fasten the hard drive’s mounting
holes to the Case Frame with 2

bi

gger

screws.

4. Finally, fasten all the four
smaller screws at both sides of

Quick Start Guide

• Mac users please refer to Mac user guide in utility CD.

Version 1.0 Sep. 2007

4 USING YOUR SECURE DRIVE

Password Authentication

Two Level Security Access

1. After you have re-plugged the Secure Drive into your
computer’s port, this Two Level Security Access window will
pop-up and prompt you to login. Enter both the password and
the security characters using the virtual keypad with a mouse
and click “Login”.

Disk content and Utility description

Disk Content:

SECURE DISK

Security HDD with data encrypted

CD PART

Virtual CD partition for auto-boot and includes
security utility

Security Utility in CD PART:

PAD_Secu.EXE

Security setup and password
setting/changing/resetting function before you
login the secure HDD

ONSPCSET.EXE

Security password Enable/disable utility

ONSPCPRT.EXE

Reset password utility, HDD data will be fully
erased!

Secure Disk

Follow these steps to check if the Secure Drive has been
properly configured. Windows automatically assigns the drive
letter.

i. In Windows Explorer, go to “My Computer”.

ii. When “Secure Disk” appears, your Secure Drive can now

used for storing data. (See Figure: My Computer)

Figure: My Computer

5 MANUAL SETTINGS

CD Partition

If the Security Access Window is not launched automatically
when you connect your Secure Drive, follow these steps:

i. In Windows Explorer, go to “My Computer”.

ii. Open “CD-PART”. (See Figure My Computer)

PAD Security Utility program

In My Computer menu, the CD PART Window, double click
“PAD_Secu.exe”

Password Security Manager

Whenever you change any password settings, the data in the
Secure Drive will not be effected.

Note: It is important not to forget your password. Otherwise, you will need

to re-configure to Secure Drive that will erase both the password
and data in the Secure Drive.

CD PART

Secure Disk

3100554160 V1.0 Sep. 2007

Security Characters

Use Virtual Keypad (see
below) to enter password or
Security Characters seen at
the Security Image on the right.

Hint

Enter a phrase to help you
recall the password you have
entered in the event that you
forget your password.

Current Password

Use Virtual Keypad
(see below) to enter current password.

New Password &
Confirm New Password

Enter minimum 4 characters password.

Disable Password Security

This box must be checked

to

disable password.

V

irtual Keypad

Use your mouse to click on the buttons in the Virtual Keypad to enter
password or Security Characters seen at the Security Image.

For advanced settings, please refer to user’s manual in utility CD