Page 1
INSTALLATION INSTRUCTIONS
AND
OWNER’S MANUAL
VENTED
ROOM HEATER
MODELS
RH-50-6 RH-65-6
RH-50C-1 RH-65C-1
RH-50-6 Shown
WARNING: If the information in these instructions are not followed exactly, a fire or explosion
may result causing property damage, personal
injury or loss of life.
— Do not store or use gasoline or other flamma-
ble vapors and liquids in the vicinity of this or
any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installer: Leave this manual with the appli-
ance.
Consumer: Retain this manual for future refer-
ence.
WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or from fuel combustion which can
cause death or serious illness.
— Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Page 1
Page 2
TABLE OF CONTENTS
SECTION PAGE
Important Safety Information .................................................................................................3
Safety Information for Users of LP Gas .................................................................................4
Introduction ............................................................................................................................5
Specifications .........................................................................................................................5
Gas Supply .............................................................................................................................6
Clearances ..............................................................................................................................7
Venting ...................................................................................................................................7
Vent Safety Shutoff System ....................................................................................................8
Reversible Vertical or Horizontal Diverter .............................................................................8
Thermostat Operation .............................................................................................................8
Lighting Instructions ..............................................................................................................9
Pilot Flame Characteristics ...................................................................................................10
Main Burner Flame Characteristics ......................................................................................10
Maintenance .........................................................................................................................11
Troubleshooting ....................................................................................................................11
How to Order Repair Parts ...................................................................................................12
Parts List RH-50 & RH-65 ...................................................................................................12
Parts View RH-50 & RH-65 .................................................................................................13
Parts List RH-50C & RH-65C .............................................................................................14
Parts View RH-50C & RH-65C ...........................................................................................15
Optional Blower Installation Instructions ...................................................................... 16-17
Service Notes ........................................................................................................................18
12822-4-0806
Page 2
Page 3
IMPORTANT SAFETY INFORMATION
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.
• Due to high temperatures, the room heater should be located
out of traffic and away from furniture and draperies.
• Children and adults should be alerted to the hazards of
high surface temperature and should stay away to avoid
burns or clothing ignition.
• Young children should be carefully supervised when they
are in the same room as the room heater.
• Clothing or other flammable material should not be placed
on or near the room heater.
• Due to high surface temperatures, keep children, clothing
and furniture away.
• Keep burner and control compartment clean.
• Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The room heater should be inspected
before use and at least annually by a qualified service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It
is imperative that control compartments, burners and
circulating air passageways of the room heater be kept
clean.
• DO NOT put anything around the heater that will ob
struct the flow of combustion and ventilation air. See
clearances.
• DO keep the appliance area clear and free from combustible material, gasoline and other flammable vapors and
liquids.
• DO examine burners periodically. Clean and replace
damaged parts.
• DO NOT use this heater if any part has been under water.
Immediately call a qualified service technician to inspect
the heater and to replace any part of the control system
and any gas control which has been under water.
• WARNING: Any change to this room heater or its controls
can be dangerous. Any safety screen or guard removed
for servicing a room heater must be replaced prior to
operating the room heater.
-
Page 3
12822-4-0806
Page 4
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precau
tions which can protect both you and your family from an ac
cident. Read them carefully now, then review them point by
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That’s your signal to go into immediate action!
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building vehicle, trailer, or area. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must find out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors in
the area mask the gas odor. People may not smell the gas odor or
their minds are on something else. Thinking about smelling a gas
odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
in LP-gas also are subject to oxidation. This fading can occur if
point with the members of your household. Someday, when
there may not be a minute to lose, everyone’s safety will de
-
pend on knowing exactly what to do. If, after reading the fol
-
lowing information, you feel you still need more information,
please contact your gas supplier.
• Use your neighbor’s phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That
will take some of the odorant out of the gas, reducing its odor
intensity.
LP-gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immedi
ately go into action as instructed earlier.
-
-
-
SOME POINTS TO REMEMBER
• Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a “Scratch and Sniff” pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-gas has a weak or abnormal odor, call your LPgas dealer.
• If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-gas
system. If you are qualified, consciously think about the odor
of LP-gas prior to and while lighting pilot lights or performing
service or making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people should
be particularly alert and careful when new tanks or cylinders
are placed in service. Odor fade can occur in new tanks, or
reinstalled old tanks, if they are filled and allowed to set too
long before refilling. Cylinders and tanks which have been
out of service for a time may develop internal rust which will
cause odor fade. If such conditions are suspected to exist, a
periodic sniff test of the gas is advisable. If you have any
question about the gas odor, call your LP-gas dealer. A
periodic sniff test of the LP-gas is a good safety measure
under any condition.
• If, at any time, you do not smell the LP-gas odorant and you
think you should, assume you have a leak. Then take the same
immediate action recommended above for the occasion when
you do detect the odorized LP-gas.
• If you experience a complete “gas out,” (the container is under no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air though openings such as pilot light orifices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having it
refilled before it is completely empty.
12822-4-0806
Page 4
Page 5
INTRODUCTION
Introduction
Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of a
vented room heater.
Instructions to Installer
1. Installer must leave instruction manual with owner after instal
lation.
2. Installer must have owner fill out and mail warranty card sup
plied with heater.
3. Installer should show owner how to start and operate heater
and thermostat.
General Information
This series is design certified in accordance with American National
Standard/CSA Standard Z21.86 and CSA 2.32 by the Canadian Stan
dards Association, as a Vented Room Heater and must be installed
according to these instructions.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not shown
on the rating plate is the responsibility of the person and com
pany making the change.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
Notice: During initial firing of this unit, its paint will bake out and
smoke will occur. To prevent triggering of smoke alarms, ventilate
the room in which the unit is installed.
Installation on Rugs and Tile
If this appliance is to be installed directly on carpeting, tile, or other
combustible material, other than wood flooring, the appliance shall
be installed on a metal or wood panel extending the full width and
depth of the appliance.
The base referred to above does not mean the fire-proof base as
used on wood stoves. The protection is primarily for rugs that may
be extremely thick and light-color tile that can discolor.
Floor pad is available from Empire Comfort Systems, Inc., Part
Number RH-425.
-
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equip
-
ment or accessories and repair and servicing of equipment shall be
performed only by a qualified agency. The term “qualified agency”
means any individual, firm, corporation, or company which whether
in person or through a representative is engaged in and is respon
sible for (1) the installation or replacement of gas piping or (b) the
connection, installation, repair or servicing of equipment, who is
experienced in such work, familiar with all precautions required
and has complied with all the requirements of the authority having
jurisdiction.
State of Massachusetts: The installation must by made by
a licensed plumber or gas fitter in the Commonwealth of
-
Massachusetts
The installation must conform with local codes, or in the absence
of local codes, with the National Fuel Gas Code, ANSI Z223.1*/
Canadian Installation Code, CAN/CGA B149.
*Available from the American National Standards Institute, Inc., 11 West 42nd St.,
New York, N.Y. 10036
High Altitudes
For altitudes/elevations above 2,000 feet (610m), input ratings should
be reduced at the rate of 4 percent for each 1,000 feet (305m) above
sea level. Canadian High Altitudes for locations having an eleva
tion above mean sea level between 2,000 feet (610m) and 4,500 feet
(1370m), the manifold pressure is to be decreased from 4.0” w.c.
(.996kPa) to 3.2” w.c. (.797kPa) for Natural Gas and from 10.0”
w.c. (2.49kPa) to 8.0” w.c. (1.99kPa) for Propane Gas.
-
-
-
SPECIFICATIONS
Models RH-50B RH-65B RH-50C RH-65C RH-50CB RH-65CB
Input BTU/HR (KW/H) 50,000 (14.6) 65,000 (19) 50,000 (14.6) 65,000 (19) 50,000 (14.6) 65,000 (19)
Height 29 9/16” (751mm) 29 9/16” (751mm) 29 9/16” (751mm) 29 9/16” (751mm) 29 9/16” (751mm) 29 9/16” (751mm)
Width
Depth including diverter 23 3/16” (589mm) 27 11/16” (704mm) 23 3/16” (589mm) 27 11/16” (704mm) 23 3/16” (589mm) 27 11/16” (704mm)
Gas Inlet 1/2” (13mm) 1/2” (13mm) 1/2” (13mm) 1/2” (13mm 1/2” (13mm) 1/2” (13mm)
Size Draft Diverter Collar 5” (127mm) 5” (127mm) 5” (127mm) 5” (127mm) 5” (127mm) 5” (127mm)
Floor to top of collar on vertical
position of Draft Diverter
Floor to center of collar on
horizontal position of Draft Diverter
Accessories
Blower Package Included Included FRB-3 FRB-3 Included Included
Radiant Package RAD-8 RAD-8 N/A N/A N/A N/A
Floor Pad RH-425 RH-425 RH-425 RH-425 RH-425 RH-425
Ceramic Log RHL-1 RHL-1 N/A N/A N/A N/A
Page 5
34” (864mm) 34” (864mm) 34” (864mm) 34” (864mm) 34” (864mm) 34” (864mm)
27 5/32” (690mm) 27 5/32” (690mm) 27 5/32” (690mm) 27 5/32” (690mm) 27 5/32” (690mm) 27 5/32” (690mm)
22 9/16” (573mm) 22 9/16” (573mm) 22 9/16” (573mm) 22 9/16” (573mm) 22 9/16” (573mm) 22 9/16” (573mm)
12822-4-0806
Page 6
GAS SUPPLY
Recommended Gas Pipe Diameter
Pipe Length
(Feet)
0-10 1/2”
10-40 1/2”
40-100 1/2”
100-150 3/4”
Note: Never use plastic pipe. Check to confirm whether your local codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
The use of the following gas connectors is recommended:
– ANS Z21.24 Appliance Connectors of Corrugated Metal Tub
ing and Fittings
– ANS Z21.45 Assembled Flexible Appliance Connectors of
Other Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The state of Massachusetts requires that a flex
ible appliance connector cannot exceed three feet in length.
Schedule 40 Pipe
Inside Diameter
Nat. LP Nat. LP
3/8”
1.3cm
1.3cm
1.3cm
1.9cm
1.0cm
1/2”
1.3cm
1/2”
1.3cm
1/2”
1.3cm
Tubing, Type L
Outside Diameter
1/2”
1.3cm
5/8”
1.6cm
3/4”
1.9cm
7/8”
2.2cm
3/8”
1.0cm
1/2”
1.3cm
1/2”
1.3cm
3/4”
1.9cm
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required by
the National Fuel Gas Code that a drip line be installed near the gas
inlet. This should consist of a vertical length of pipe tee connected
into the gas line that is capped on the bottom in which condensation
and foreign particles may collect.
Figure 2
-
-
Figure 1
Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/
CGA-B149 (.1 or .2) installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate, contact
your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
12822-4-0806
Method of Installing a Tee Fitting Sediment Trap
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8” (3mm) N.P.T.
plugged tapping, accessible for test gauge connection, must be
placed immediately upstream of the gas supply connection to
the appliance.
2. The appliance and its individual shutoff valve must be discon
nected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 psig
(3.5 kPa)
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 (kPa).
Attention! If one of the above procedures results in pressures in
excess of 1/2 psig (14” w.c.) (3.5 kPa) on the appliance gas valve,
it will result in a hazardous condition.
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure
regulator in the gas valve. Natural gas models will have a manifold
pressure of approximately 4.0” w.c. (.996kPa) at the valve outlet
with the inlet pressure to the valve from a minimum of 5.0” w.c.
(1.245kPa) for the purpose of input adjustment to a maximum of
10.5” w.c. (2.61kPa). Propane gas models will have a manifold
pressure approximately 10.0” w.c. (2.49kPa) at the valve outlet
with the inlet pressure to the valve from a minimum of 11.0” w.c.
(2.739kPa) for the purpose of input adjustment to a maximum of
13.0” w.c. (3.23kPa).
A 1/8” (3mm) N.P.T. plugged tapping, accessible for test gauge
connection, is located on the outlet side of the gas control.
Page 6
-
Page 7
CLEARANCES
(3m)
(3m)
(.6m
)
(.9m)
Clearances: When facing the front of the room heater the minimum clearances to combustible construction (material) are the
following:
Left side - 6 inches (152mm)
Right side - 6 inches (152mm)
Recommend 18 inches (457mm) on left side for servicing
VENTING
1. Flue pipe must be as large as the flue collar on the draft diverter.
2. Maintain an upward slope of at least 1/4 inch (6mm) per foot
of horizontal run.
3. Run flue pipe as directly as possible with a minimum of el
bows.
4. Flue pipe should extend through the wall of a chimney to be
flush with inner wall.
5. Flue pipe must be adequately supported by metal strips.
6. Single wall vent pipe may be attached directly to the draft hood
of the room heater when clearance of 2 1/2 inches (64mm)
is maintained between the single wall vent pipe and the com
bustible wall of the room in which the room heater is located.
Use double wall vent pipe for 1 inch (25mm) clearance to
combustibles.
7. For flue pipe running through walls and roof, use B-1 [1 inch
(25mm) clearance to combustibles] vent pipe.
8. Chimneys should extend at least 2 feet (.6m) above the roof and
above any object or nearby building within 10 feet (3m).
9. Open tees should not be used in the flue pipe.
10. Appliance must not be connected to a chimney flue that is
servicing a separate solid-fuel burning appliance.
For proper venting, do not attach a 90o elbow directly to draft diverter. If possible, attach 2 feet (.6m) of straight vent pipe before
an elbow is used. Use of 45o elbows is recommended.
Uninsulated single-wall metal pipe shall not be used outdoors
in cold climates for venting gas utilization equipment.
Ventilation and Combustion Air
Room heaters shall be installed in a location in which the facilities
for ventilation permit satisfactory combustion of gas and proper
venting under normal conditions. In buildings of conventional
frame, brick or stone construction without tight storm windows and
doors, infiltration is normally adequate to provide for combustion
and draft hood dilution.
Where appliances are installed in a confined space within a building,
the building being of unusually tight construction, air for combustion
and ventilation must be obtained directly from outdoors or from
such spaces that freely communicate with the outdoors. Under these
conditions, the confined space shall be provided with two permanent
openings, one near the top of the enclosure and one near the bottom;
each opening shall have a free area of not less than one square inch
(6.5cm2) per 1,000 BTU’s (.3KW) of total input. The draft hood
must be in the same atmospheric pressure zone as the combustion
air inlet to the appliance.
Do not install in alcove or closet.
No horizontal projection above heater permitted within 55 inches
(140 cm).
Ceiling 55 inches (140cm)
Draft hood to rear wall 2 inches (51 mm)
Open in front to provide service, access, and clearance to construction.
Liner and Insulated Liner
When you install a vented room heater into a masonry chimney you
must follow these steps.
-
1. The chimney must be lined and sized properly. Most masonry
chimneys are over sized and absorb too much heat to be con
sidered a proper vent. If you have any doubts line the chimney
with the right size liner. If it’s unlined you must line it.
2. Use an insulated liner when the chimney is on the outside,
-
three sides exposed to the weather, and there is no clay liner
in the chimney. The insulation will help keep the flue gases
warmer.
Insulated Vent Enclosure
Vented room heaters installed with the vent going directly to the
outside and above the eaves can cause poor venting. The cold pipe
will have a delay in proper venting and cause the room heater to
shut “off” by the vent safety switch. To prevent delayed venting
as well as condensation of flue products an insulated enclosure is
recommended.
Use type B 5” (127mm) diameter vent pipe and maintain at least a
one inch (25mm) clearance to combustibles.
Use metal thimble to protect vent pipe as it passes through com
bustibles.
-
-
Page 7
Figure 3
12822-4-0806
Page 8
VENT SAFETY SHUTOFF SYSTEM
This heater must be properly connected to a venting system. This
heater is equipped with a vent safety shutoff system.
Warning:
Operation of this heater, when not connected to a
properly installed and maintained venting system or
tampering with the vent safety shutoff system, can result in
carbon monoxide (CO) poisoning and possible death.
This appliance needs fresh air for safe operation and must be
installed so there are provisions for adequate combustion and
ventilation air.
This room heater is equipped with a vent safety switch. The vent
safety switch will cause gas flow to the pilot to “shut off” due to
improper venting or a blocked flue.
If the vent safety switch continues to “shut off” the gas flow to
the pilot, a qualified service person must be contacted to inspect
for improper venting, blockage in the vent pipe or the vent safety
switch for being defective.
REVERSIBLE VERTICAL OR HORIZONTAL DRAFT DIVERTER
This room heater has a reversible draft diverter. The draft diverter
is installed in the vertical position at the factory. Please use the
following steps to change the draft diverter from the vertical
positing to the horizontal position.
1. Remove L280 vent safety switch from the draft diverter.
2. Inside your yellow instruction envelope will be a 1 1/2” x 2
1/4” (38mm x 51mm) vent safety switch hole cover plate and
two (2) 1/2” screws for attachment of vent safety switch hole
cover plate to the draft diverter. Attach vent safety switch hole
cover plate over hole on the draft diverter from which the L280
vent safety switch was removed.
3. Remove two (2) screws at bottom of draft diverter and lift
upward to remove draft diverter from the draft diverter plate.
Rotate draft diverter into the horizontal position and slide back
into the draft diverter plate. Attach two (2) screws into bottom
of the drafter diverter.
4. Remove vent safety switch hole knockout and two (2) knockouts
for screws on opposite side of draft diverter.
5. Attach L280 vent safety switch to the draft diverter.
6. Repositioning of the draft diverter is completed.
DRAFT DIVERTER CAN BE EITHER A VERTICAL VENT
OR HORIZONTAL VENT
Figure 4
THERMOSTAT OPERATION
To turn on burner, rotate dial knob toward setting number 7. To
shut down burner, rotate dial knob toward setting number 1.
The dial numbers 1 to 7 correspond to 50o to 90oF (10o to 32oC).
This temperature at the bulb thermostat, not the room temperature. The owner is advised to determine the particular heat setting
that is desired for comfort, as heating requirements are different
for every owner.
12822-4-0806
Attention: If no heat is desired, turn the gas control knob to the
PILOT position.
Page 8
Page 9
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone, Follow the gas supplier’s instructions.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Set thermostat to lowest setting.
3. Turn off all electric power to the appliance (if applicable).
4. Remove access panel (front panel).
5. Push in gas control knob slightly and turn clockwise
to “OFF.” Do not force.
6. Wait ten (10) minutes to clear out any gas. Then, smell for
gas, including near the floor. If you smell gas, STOP! Follow
“B” in the safety information above on this label. If you do
not smell gas, go to the next step.
7. Find pilot - the pilot is attached to front of burner.
8. Turn gas control knob counterclockwise
to “IGN.”
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don’t try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
9. Depress and turn gas control knob counterclockwise
to “PILOT.” A spark is produced when gas control
knob is turned between “IGN” and “PILOT.” Repeatedly
depress and turn gas control knob between “IGN” and “PI
LOT” until pilot is ignited. Continue to hold the control knob
in for about one (1) minute after pilot is lit. Release knob and
it will pop back up. If it goes out, repeat steps 5 through 9.
• If knob does not pop up when released, stop and im
mediately call your service technician or gas supplier.
•If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician or
gas supplier.
10. Attention! Gas control has INTERLOCK latching device.
When the pilot is initially lit and the safety magnet is energized
(pilot stays on) the INTERLOCK latching device becomes
operative. If the gas control is turned to the “OFF” position
or gas flow to the appliance is shut off, the pilot cannot be re
lighted until the safety magnet is de-energized (approximately
60 seconds). There will be an audible “click” when the safety
magnet in the gas control is de-energized. Pilot can now be
relighted. Repeat steps 5 through 9.
11. Turn the gas control knob counterclockwise
to “ON.”
12. Turn on all electric power to the appliance (if applicable).
13. Replace access panel (front panel). Set thermostat to desired
setting.
-
-
-
TO TURN OFF GAS APPLIANCE
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance (if applicable), if
service is to be performed.
Page 9
3. Push in gas control knob slightly and turn clockwise
to “OFF.” Do not force.
12822-4-0806
Page 10
PILOT FLAME CHARACTERISTICS
( 5 m m
)
The correct flame will be almost horizontal, blue and will extend
past the thermocouple 1/4” (6mm). The flame will surround the
thermocouple just below the tip.
On Propane (LP-gas) slight yellow might occur where the pilot
flame and the burner flame meet.
Natural gas pilots require adjusting when the inlet pressure is
above 5” w.c. (1.25kPa). Remove pilot adjustment cover. Turn
adjustment screw clockwise to reduce flame.
Propane (LP-gas) will not require adjusting.
Figure 5
MAIN BURNER FLAME CHARACTERISTICS
There will be a short blue inner flame with a larger, lighter blue secondary flame. The burner flame may have yellow tips when hot.
Dust in the combustion air will produce and orange or red flame. Do not mistake the orange or red flame for an improper yellow flame.
The flame will be proper if the factory-set pressure and orifice are used. After use, cleaning may be required for the proper flame.
On Propane gas, if a whistling noise (resonation) occurs
a. Screw the air adjustment bolt into the burner throat to eliminate the whistling noise (resonation).
b. Size main burner orifice with a drill bit. For RH-50(C) use #47 drill bit. For RH-65(C) use 2.3mm drill bit.
Primary Air Adjustment see page 11.
12822-4-0806
Figure 6
Page 10
Page 11
MAINTENANCE
Cleaning Pilot Burner
After use, cleaning of the pilot burner may be required for the
proper flame. The pilot orifice can be cleaned with high pressure
air or by placing under running water. Pilot orifice must be dry
before replacement. Use a pipe cleaner to clean inside the pilot
after the pilot orifice has been removed.
Removing Pilot Orifice
1. Disconnect the pilot supply line at the pilot burner
2. Remove pilot orifice from pilot burner. It may be necessary to
tap on pilot burner in order to remove the pilot orifice.
Cleaning Main Burner
Remove the burner and apply water pressure inside the throat of the
burner and down into the ports; follow with air pressure.
Removing Main Burner
1. Remove casing front.
2. Disconnect pilot bracket from the burner.
3. Remove brass nut from burner.
4. Disconnect burner from chamber leg flange.
5. Remove burner from bottom of combustion chamber.
Cleaning Combustion Chamber
A qualified serviceman should remove the chamber and apply air
pressure to the inside in order to clear all passageways.
Primary Air Adjustment
1. A primary air adjustment bolt is located on left, front of burner throat.
The bolt can be screwed into burner throat to REDUCE primary
air or unscrewed from burner throat to INCREASE primary air.
To r e du c e y el l ow fl a m e on m ai n b u rn e r,
unscrew bolt from burner throat. Also, refer to Step 2.
To reduce resonation (whistling) noise or extinction (popping)
noise, screw bolt into burner throat.
2. An air shutter bracket is attached to top of burner throat.
The air shutter bracket lays flat across top of burner throat.
If yellow flames can not be removed from main burner by
using primary air adjustment bolt, the air shutter bracket can
be pivoted upward to allow additional primary air to enter
burner throat.
On Propane gas, if a whistling noise (resonation) occurs, screw
the air adjustment bolt into the burner throat to eliminate the
whistling noise (resonation).
TROUBLESHOOTING
1. Impossible to light pilot
a. If using piezo ignitor, check electrode location.
b. Remove nut at orifice and check for gas.
c. If gas available, check for blocked orifice or pilot.
2. Pilot outage
a. Proper size of pilot flame.
b. Defective or weak thermocouple.
3. Pilot flames but goes out
a. Pilot flame not covering the thermocouple properly when
knob is released.
b. Defective thermocouple.
c. Defective magnet in the safety section of valve.
4. Poor thermostatic control
a. Thermostat needs calibrating.
b. Defective thermostat section.
5. Noisy blower
a. Tighten blower screws.
b. Check blower wheel in the open for balance.
6. Yellow main burner flame
a. Remove main burner to check for obstructions in throat,
ports and orifices.
b. Install new main burner orifice and pilot orifice
c. Check gas valve for leaking.
d. Open the air bolt on the main burner in order to increase the
amount of primary air.
7. Yellow pilot flame
a. Small yellow tip not objectionable.
b. Remove pilot orifice. Check and clean.
8. Pilot and main burner go out after burning a few minutes
a. Improper venting of flue products. Relight and check for
improper venting.
b. If vented properly, check vent safety switch, replace if
defective.
9. Burner back-flashes or ‘pops’ and burns and main burner
orifice.
a. Examine burner for defects.
10. Inoperative blower
a. Check fan control by shorting across terminals.
b. Check for blower wheel bind by removing wheel and operat
ing motor.
c. Check for frozen bearings due to lack of oil.
-
Page 11
12822-4-0806
Page 12
HOW TO ORDER REPAIR PARTS
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts
through the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your
equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate
illustration and list. Be sure to give all this information...
Furnace Model Number Part Description
Furnace Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529
PARTS LIST RH-50 & RH-65
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
INDEX
1 11723 Diverter Assembly 25 P-267 Manifold Assembly (RH-50-6)
2 RH-802 Down Draft Shield (RH-50-6 NAT &
2 RH-851 Down Draft Shield (RH-65-6 LPG) 26 P86-3.7mm Main Burner Orifice (RH-65-6 Nat)
3 11724 Draft Diverter Plate 26 P86-3.1mm Main Burner Orifice (RH-50-6 Nat)
4 11719 Casing Top (RH-50-6) 26 P86-2.3mm Main Burner Orifice (RH-65-6 LPG)
4 11720 Casing Top (RH-65-6) 26 P86-47 Main Burner Orifice (RH-50-6 LPG)
5 11707 Louver (RH-50-6, 3 required)
6 11745 Casing Back 28 R-6101 Gas Valve (Nat)
7 RH-652 Combustion Chamber Assembly (RH-50-6) 28 R-6102 Gas Valve (LPG)
7 RH-626 Combustion Chamber Assembly (RH-65-6) 29 11743 Control Rod
8 RH-654 Chamber Shield - Right (RH-50-6) 30 11700 Control Rod Bracket
8 RH-655 Chamber Shield - Right (RH-65-6) 31 R-6096 Knob & Adaptor Set
9 11721 Casing Side (RH-50-6) 32 11728 Motor Mounting Plate
9 11722 Casing Side (RH-65-6) 33 R-587 Motor Cushion
10 RH-060 Radian Glass with Rope Gasket 34 R-2605 Motor
11
12 11727 Blower Housing and Chute Assembly 35 11721 Casing Side (RH-50-6)
13 RH-520 Glass Frame Assembly 36 RH-653 Chamber Shield - Left
14 RH-138 Blower Cushion 37 R-2099 Cord Set
15 RH-618 Inner Front 38 RH-656 Chamber Shield - Rear
16 11725 Casing Bottom Assembly (RH-50-6) 39 R-2091 Wire Assembly
16 11726 Casing Bottom Assembly (RH-65-6) 40 R-1468 Strain Relief Bushing
17 RH-853 Burner 41 R-896 Bushing
18 11717 Casing Front with Heat Shield (USA) 42 R-1156 Fan Control Switch
18 15674 Casing Front with Heat Shield (Canada) 43 RH-863 Switch Box Assembly
19 R-776 Thermocouple 44 DV-807 Switch Box Cover
20 RH-620 Pouch 45 R-8195 ECO Wire Assembly
21 R-775L Pilot Burner with Orifice (LPG) 46 R-2706 Eco Switch
21 R-775N Pilot Burner with Orifice (Nat) Not Shown 742148 Pilot Orifice .011 (Nat)
22 R-6126 Electrode and Wire Assembly Not Shown 742250 Pilot Orifice .008 (LPG)
23 11712 Pilot Tubing (RH-50-6) Not Shown RH-527 Glass and Frame Assembly (Includes 10 and 13)
23 11713 Pilot Tubing (RH-65-6) Not Shown R-1630 ECO Adapter
24 RH-457 Air Shutter Bracket Not Shown UH-441 Vent Safety Switch/ECO Hole Cover Plate
PART
NO.
NUMBER
R-369 Blower Wheel 35 11722 Casing Side (RH-65-6)
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
DESCRIPTION INDEX
NO.
25 P-268 Manifold Assembly (RH-65-6)
LPG-RH-65-6 NAT)
27 11746 Valve Bracket
(RH-65-6, 4 required)
PART
NUMBER
DESCRIPTION
12822-4-0806
Page 12
Page 13
PARTS VIEW RH-50 & RH-65
Page 13
12822-4-0806
Page 14
PARTS LIST RH-50C & RH-65C
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
INDEX
NO.
1 11723 Diverter Assembly 18 R-6126 Electrode and Wire Assembly
2 RH-802 Down Draft Shield (RH-50C-1 NAT & LPG) 19 11712 Pilot Tubing (RH-50C-1)
2 RH-851 Down Draft Shield (RH-65C-1 NAT & LPT) 19 11713 Pilot Tubing (RH-65C-1)
3 11724 Draft Diverter Plate 20 RH-457 Air Shutter Bracket
4 11719 Casing Top (RH-50C-1) 21 P-267 Manifold Assembly (RH-50C-CB-1)
4 11720 Casing Top RH-65C-1) 21 P-268 Manifold Assembly (RH-65C-1)
5 11707 Louver (RH-50C-1, 3 Required) (RH-65C-1, 4
6 11745 Casing Back 22 P86-3.1mm Main Burner Orifice (RH-50C-1 NAT)
7 11741 Combustion Chamber Assembly (RH-50C-1) 22 P86-2.3mm Main Burner Orifice (RH-65C-1 LPG)
7 11742 Combustion Chamber Assembly (RH-65C-1) 22 P86-47 Main Burner Orifice (RH-50C-1 LPG)
8 RH-654 Chamber Shield - Right (RH-50C-1) 23 11746 Valve Bracket
8 RH-655 Chamber Shield - Right (RH-65C-1) 24 R-6101 Gas Valve (NAT)
9 11721 Casing Side (RH-50C-1) 24 R-6102 Gas Valve (LPG)
9 11722 Casing Side (RH-65C-1) 25 11743 Control Rod
10 RH-618 Inner Front 26 11700 Control Rod Bracket
11
11
12 RH-624 Rear Shield 28 11721 Casing Side (RH-50C-1)
13 11725 Casing Bottom Assembly (RH-50C-1) 29 RH-653 Chamber Shield - Left
13 11726 Casing Bottom Assembly (RH-65C-1) 30 RH-656 Chamber Shield - Rear
14 RH-853 Burner 31 R-8195 ECO Wire Assembly
15 11755 Casing Front Assembly (USA) 32 R-2706 Eco Switch
15 15675 Casing Front Assembly (Canada) Not Shown 742148 Pilot Orifice .011 (NAT)
16 R-776 Thermocouple Not Shown 742250 Pilot Orifice 0.008 (LPG)
17 R-775L Pilot Burner with Orifice (LPG) Not Shown R-1630 ECO Adaptor
17 R-775N Pilot Burner with Orifice (NAT) Not Shown UH-441 Vent Safety Swtich/ECO Hole Cover
PART
NUMBER
RH-625 Bottom Reflector (RH-50C-1) 27 R-6096 Knob & Adaptor Set
RH-660 Bottom Reflector (RH-65C-1) 28 11722 Casing Side (RH-65C-1)
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
DESCRIPTION INDEX
NO.
22 P86-3.7mm Main Burner Orifice (RH-65C-1 NAT)
Required)
PART
NUMBER
DESCRIPTION
Plate
12822-4-0806
Page 14
Page 15
PARTS VIEW RH-50C & RH-65C
Page 15
12822-4-0806
Page 16
OPTIONAL BLOWER INSTALLATION INSTRUCTIONS
FRB-3 For Vented Room Heaters
Models
RH-50-(1, 2, 3, 4, 5, 6) RH-50C-1
RH-65-(1, 2, 3, 4, 5, 6) RH-65C-1
Figure 1
Installing Optional Blower
1. Remove rear shield (2 screws) and bottom reflector (4 screws).
(See Figure 1)
2. Align blower cushion with bottom assembly air discharge
opening. Foil face side of blower cushion should be placed
upward.
3. Align blower housing with blower cushion and use two #10
x 1/2” (13mm) hex-head screws to attach blower housing to
bottom assembly. (See Figure 2)
4. Save bottom reflector and rear shield (removed in Step 1) in
the even the blower housing is removed from room heater.
Attention! Bottom reflector and rear shield must be at
tached to bottom assembly whenever the blower housing
in removed from the room heater and the room heater is
in operation.
5. Remove switch box cover from the switch box by removing
the #8 x 1/4” (6mm) hex-head screw.
6. There are two screw holes on the lower back of the combus
tion chamber. Use only the left screw hole for mounting.
7. With the switch box perpendicular to the combustion chamber,
align the round clearance hole on the switch box with the left
screw hole on the combustion chamber (See Figure 3).
8. Attach switch box to the combustion chamber using the #10
x 1/2” (13mm) hex-head screw provided.
9. Attach switch box cover to the switch box by using the #8 x
1/4” (6mm) hex-head screw. (See Figure 4)
Figure 2
-
-
Figure 3
Figure 4
12822-4-0806
Page 16
Page 17
Attention: Wiring harness on blower is factory assembled and
installed. If wiring harness becomes disassembled, use the following steps to reassemble the wiring harness.
1. Attach (1) pin terminal from black (hot) wire, smooth insulation
on cord set to (1) socket terminal on fan control assembly.
2. Attach (1) pin terminal from black (neutral) wire, ribbed insu
lation on cord set to (1) socket terminal from white (neutral)
wire on motor.
3. Attach (1) pin terminal on fan control assembly to (1) socket
terminal from black (hot) wire on motor.
4. Attach green ground wire beneath one of the #10 x 1/2” (13mm)
screws on the blower housing.
Fan Control
The automatic fan control is located in the switch box. The switch
box is attached to the front of the blower assembly. The switch box
is adjacent to the combustion chamber. The fan control is a nonadjustable automatic type. The fan control will require between
5 and 10 minutes of main burner operation before the fan control
“closes” and activates the blower. The blower will continue to run
between 5 and 10 minutes after the main burner shuts off, before
the fan control “opens” and deactivates the blower.
Wiring
The appliance, when installed, must be electrically grounded in ac
cordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70 or Canadian Electrical
Code, CSA C22.1, if an external electrical source is utilized.
-
appliance is equipped with a three-prong [grounding] plug for
your protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this plug. For an
ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screws.
With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded. A 7/8”
(22mm) hole is provided in the junction box for use with a conduit
connector if local codes require this type of protection.
Wiring Diagram
-
This
Index
No.
Part
No.
Description
1 11727 Blower Housing and Chute Assembly
2 9120106 Fan Control Switch
3 RH-863 Switch Box
4 DV-807 Switch Box Cover
5 R-2091 Wire Assembly
6 642031 Blower Wheel
7 11728 Motor Mounting Plate
8 632016 Motor Cushion
9 R-2605 Motor
10 8720161 Strain Relief Bushing
11 R-2099 Cord Set
12 RH-138 Blower Cushion
If any of the original wire as supplied with the appliance must be
replaced, it must be replaced with type 125
o
C wire or its equiva-
lent.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and danger
-
ous operation. Verify proper operation after servicing.
Warning:
Unplugging of blower accessory will not stop the heater
from cycling. To shut heater off:
1. Turn temperature dial or thermostat to lowest setting.
2. Turn knob n gas control to “OFF,” depressing slightly.
Do not force.
Cleaning
The blower wheel will collect lint and could require cleaning once
a year. If the air output decreases or the noise level increases, it
indicates a dirty wheel. Complete removal of the wheel and scrub
bing it with a brush under flowing water is recommended.
Oiling
The blower motor has an oil hole located on each end of the motor.
Use #20 motor oil only. It is best to oil the motor several times during
the heating season using 2 or 3 drops each time. If the motor fails
to start and hums, it could be a tight bearing due to lack of oil. This
may be corrected by pouring kerosene in the oil holes, allowing to
stand for a few hours and then oiling properly.
-
Page 17
12822-4-0806
Page 18
SERVICE NOTES
12822-4-0806
Page 18
Page 19
SERVICE NOTES
Page 19
12822-4-0806
Page 20
SERVICE NOTES
12822-4-0806
Empire Comfort Systems, Inc.
918 Freeburg Ave. Belleville, IL 62220
PH: 618-233-7420 or 800-851-3153
FAX: 618-233-7097 or 800-443-8648
info@empirecomfort.com
www.empirecomfort.com
Page 20
Loading...