Empire Comfort Systems BI28GP-5, BF28GP-5, BI28BM-5, BI28CN-5, BP28BM-5 Installation Instructions Manual

...

Download

Page 1

INSTALLATION INSTRUCTIONS

™

EMPIRE

Comfor t Systems

WARNING

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness.

Attention: Check local codes for venting requirements.

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.

POWER-VENT

HIGH-EFFICIENCY

FIREPLACE WITH

BAY WINDOW MANTIS MODELS

BF28(B,C,G)M(N,P)-5

BI28(B,C,G)M(N,P)-5

BP28(B,C,G)M(N,P)-5

FIREPLACE MANTIS MODELS

FF28BM(N,P)-3

FI28BM(N,P)-3

FW28BM(N,P)-3

WARNING: If the information in these instructions are not followed exactly, a re or explosion may result causing property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the

— Installation and service must be performed by a

qualied installer, service agency or the gas supplier.

re department.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to a

replace or stove, install an adjustable safety gate to keep

toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by state or local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use

with other gases, unless a certied kit is used.

Page 1

Page 2

TABLE OF CONTENTS

SECTION PAGE

Important Safety Information ............................................................................................................ 3

Safety Information for Users of LP-Gas............................................................................................ 4

Requirements for Massachusetts ..................................................................................................... 5

Introduction ....................................................................................................................................... 6

Specications and Accessories ........................................................................................................ 7

Installation and General Safety Information ..................................................................................... 8

Gas Supply ....................................................................................................................................... 9

Vent Clearances ............................................................................................................................. 10

Venting Requirements .................................................................................................................... 11

Vent Examples for Single Flue ....................................................................................................... 12

Direct Vent and Colinear Vent Examples...................................................................................13-14

Colinear Transition Vent Kit ............................................................................................................ 15

Vent Adaptor Kits ............................................................................................................................ 15

Rough Framing Dimensions ........................................................................................................... 16

Insert Into Masonry Fireplace ......................................................................................................... 17

Bay Window Mantis Clearance to Combustibles ............................................................................ 18

Fireplace Mantis Clearance to Combustibles ................................................................................. 19

Bay Window Mantis Specications ............................................................................................ 20-21

Fireplace Mantis Specications ................................................................................................. 22-23

Gas Connection Installation............................................................................................................ 24

Bay Window Mantis Log Set Installation Instructions ..................................................................... 25

Fireplace Mantis Log Set Installation Instructions .......................................................................... 26

Wiring .............................................................................................................................................27

Start Up Check List......................................................................................................................... 28

Lighting Instructions........................................................................................................................ 29

Start Up and Adjustments ..........................................................................................................30-31

FRBTC Remote Instructions......................................................................................................32-37

Automatic Humidier Operation...................................................................................................... 38

Optional Controls ............................................................................................................................ 39

Maintenance & Service..............................................................................................................40-41

Bay Window Mantis Parts List ................................................................................................... 42-43

Bay Window Mantis Parts View ................................................................................................. 44-45

Fireplace Mantis Parts List ........................................................................................................46-47

Fireplace Mantis Parts View ........................................................................................................... 48

Master Parts Distributor List ........................................................................................................... 49

How To Order Repair Parts ............................................................................................................49

Warranty Terms .............................................................................................................................. 50

Appliance Service History............................................................................................................... 51

28743-0-0711Page 2

Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

Safety markings are frequently used in this manual to designate a degree or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation that if not avoided, could re-

sult in personal injury or death.

CAUTION indicates a potentially hazardous situation that if not avoided, may result

in minor or moderate injury or property damage.

WARNING

This appliance must be installed and repaired by

a qualied service person who is familiar with the

proper installation and operation of the Mantis Pow-

er-Vent High Efciency Fireplace. Installers who are

not familiar with the installation of the Mantis and have questions, should contact Empire Comfort Systems, Inc. prior to installing the appliance to avoid creating a hazardous operating condition.

• Due to high temperatures the appliance should be

located out of trafc and away from furniture and

draperies.

• Children and adults should be alerted to the haz-

ards of high surface temperatures and should stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to a replace or stove, install an adjustable safety gate to keep away toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ammable material should not

be placed on or near the appliance.

• Any safety screen or guard removed for servicing an

appliance, must be replaced prior to operating the appliance.

• Keep burner and control compartment clean.

• For manufactured home (USA only) or mobile home

or residential installation convertible for use with natural gas and liqueed petroleum gases when provision is made for the simple conversion from one gas to the other.

WARNING

Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be inspected before use and at least annually by a

qualied service person. More frequent cleaning may

be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

• DO NOT put anything around the heater that will obstruct the ow of combustion and ventilation

air.

• DO keep the appliance area clear and free from combustible material, gasoline and other ammable

vapors and liquids.

• Do examine venting system periodically and replace damaged parts.

• Do make a periodic visual check of burner. Clean

and replace damaged parts.

• DO NOT use this heater if any part has been under water. Immediately call a qualied service techni-

cian to inspect the heater and to replace any part of the control system and any gas control which has been under water.

• DO NOT operate this appliance without the front

panel installed.

Note to the Installer

1. The installer must leave instruction manual with owner after installation.

2. The installer must have the owner ll out and mail registration card supplied with the heater.

3. The installer should show the owner how to start and operate heater and thermostat.

4. The installer must locate unit near a grounded wall

receptacle for 115VAC power and must provide gas

supply and vent the unit properly for safe operation.

28743-0-0711 Page 3

Page 4

SAFETY INFORMATION FOR USERS OF LP-GAS

LP-Gas (Propane) is a ammable gas which can cause res and

explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review them point by point with the members

of your household. Someday, there may not be a minute to lose, everyone’s safety will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more information, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

• Do not operate electric switches, light matches, use your

phone. Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• LP-Gas is heavier than air and may settle in low areas such

as basements. When you have reason to suspect a gas leak, keep out of basements and other low areas. Stay out until

reghters declare them to be safe.

• Use your neighbor’s phone and call a trained LP-Gas service person and the re department. Even though you may not

continue to smell gas, do not turn on the gas again. Do not re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and reghters check for escaped gas. Have them air out the area before you return. Properly

trained LP-Gas service people should repair the leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must nd out if you

can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.

The odorant in LP-gas is colorless, and it can fade under some circumstances. For example, if there is an underground leak, the

movement of the gas through soil can lter the odorant. Odorants in LP-Gas also are subject to oxidation. This fading can occur if

there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.

LP-Gas may stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there

may be more odor at lower levels. Always be sensitive to the

slightest gas odor. If you detect any odor, treat it as a serious leak. Immediately go into action as instructed earlier.

• Learn to recognize the odor of LP-gas. Your local LP-Gas

Dealer can give you a “Scratch and Sniff” pamphlet. Use it

to nd out what the propane odor smells like. If you suspect

that your LP-Gas has a weak or abnormal odor, call your LP-Gas Dealer.

• If you are not qualied, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gas system. If you are qualied, consciously think about the odor

of LP-Gas prior to and while lighting pilot lights or performing

service or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the LP-Gas odor. Do not try to light

pilot lights, perform service, or make adjustments in an area

where the conditions are such that you may not detect the odor if there has been a leak of LP-Gas.

• Odor fade, due to oxidation by rust or adsorption on walls

of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or

cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are lled and allowed to set too long before relling. Cylinders and tanks which

have been out of service for a time may develop internal rust which will cause odor fade. If such conditions are sus-

SOME POINTS TO REMEMBER

pected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-gas

dealer. A periodic sniff test of the LP-gas is a good safety

measure under any condition.

• If, at any time, you do not smell the LP-Gas odorant and

you think you should, assume you have a leak. Then take the same immediate action recommended above for the

occasion when you do detect the odorized LP-Gas.

• If you experience a complete “gas out,” (the container

is under no vapor pressure), turn the tank valve off immediately. If the container valve is left on, the container may draw in some air through openings such as pilot light orices. If this occurs, some new internal rusting could occur. If the valve is left open, then treat the container as

a new tank. Always be sure your container is under vapor

pressure by turning it off at the container before it goes completely empty or having it relled before it is completely empty.

28743-0-0711Page 4

Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed

in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination

is less than seven (7) feet above nished grade in the area of

the venting, including but not limited to decks and porches, the

following requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gastter shall

observe that a hard wired carbon monoxide detector with an

alarm and battery back-up is installed on the oor level where

the gas equipment is to be installed. In addition, the installing

plumber or gastter shall observe that a battery operated

or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or

structure served by the side wall horizontal vented gas fueled

equipment. It shall be the responsibility of the property owner

to secure the services of qualied licensed professionals for

the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and

battery back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with the

above provisions shall comply with NFPA 720 and be ANSI/ UL 2034 listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be

permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line

with the exhaust vent terminal for the horizontally vented

gas fueled heating appliance or equipment. The sign shall

read, in print size no less than one-half (1/2) inch in size,

“GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not

approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from

248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the most

current edition of NFPA 54 as adopted by the Board;

and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the ue gases, but identies

“special venting systems”, the following requirements

shall be satised by the manufacturer:

1. The referenced “special venting system” instructions

shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for

that system shall include a parts list and detailed installation instruction.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instructions

shall remain with the appliance or equipment at the completion of the installation.

28743-0-0711 Page 5

Sate of Massachusetts: The installation must be made

by a licensed plumber or gas tter in the Commonwealth of

Massachusetts.

Page 6

INTRODUCTION

WARNING

The safety information listed below must be followed during the installation, service, and operation of this product. Failure to following the safety recommendations could result in possible damage to the equipment, serious personal injury, or death.

Additional code information listed below is for reference purposes only and does not necessarily have jurisdiction over local or state codes. Always consult with local authorities before installing any gas appliance.

Combustion and Ventilation Air

U.S.: National Fuel Gas Code NFPA 54/ANSI Z223.1(NFGC), Air

for Combustion and Ventilation.

Electrical Connections

U.S.: National Electrical Code (NEC) ANSI/NFPA 70

Gas Piping and Gas Pipe Pressure Testing

U.S.: NFGC and National Plumbing Codes

General Installations

U.S.: Current edition of the NFGC and NFPA 90B. For copies contact the National Fire Protection Association Inc., Batterymarch Park, Quincy, MA 02269 or American Gas Association, 400 N. Capitol, N.W., Washington DC 20001 or www.NFPA.org.

Safety

U.S.: NFGC NFPA 5/ANSI Z223.1

28743-0-0711Page 6

Page 7

SPECIFICATIONS & ACCESSORIES

Fireplace Mantis Models F(F,I,W)28BM(N,P)

Input BTU/HR (KW/H) 15,000 Rear - 13,000 Front

Height 24-9/16”

Width 28”

Depth 17-3/16”

Gas Inlet (Pipe) 3/8” Flair

Electrical - The unit comes equipped with a 5 foot (1.5 m) 3

pronged cord, for connection to an approved

115 VAC, 60 Hz, 5A (maximum) wall receptacle.

Vent Pipe: - 1-1/2 inch diameter schedule 40 PVC pipe, 40 feet

maximum equivalent length.

ACCESSORIES

Part Number Description

TRW Wall Thermostat - Wireless Remote

FRBTP Battery Operated Remote with Programmable Thermostat

PVCA Colinear Adapter

PVCT Colinear Transition Kit

PVVK-CFA Flex Vent Kit

PVVK-SH Single Flue Horizontal Vent Kit

PVVK-SV Single Flue Vertical Vent Kit

PVVTC Vertical Termination Cap - 1-1/2”

PVVK24H Coaxial Horizontal Direct Vent Kit (24”)

PVVK48H Coaxial Horizontal Direct Vent Kit (48”)

Bay Window Mantis

CIFPB-1C Corner Floor Pad Kit

CIPFP-1 Floor Pad Kit

PV-2H Slim Top Cover Kit

PV-4H Short Top Cover Kit

PVE-1 Metal Surround Kit, 35”

PVE-2 Metal Surround Kit, 38”

PVPK Pedestal Kit

PVSH Rear Shroud

Fireplace Mantis

FWK28(BL,CM,HP,SS) In-Wall Surround Kit, Picture Frame

FGK28(BL,SS) In-Wall Surround Kit, Louverless

FIK28(BL,CM,HP,SS) Insert Package

FFK28(BL,CM,HP,SS) Fireplace Mantel Surround Kit

Bay Window Mantis Models B(F,I,P)28(B,C,G)M(N,P)

Input BTU/HR (KW/H) 19,000 Rear - 9,000 Front

Height 25-1/4”

Width 28”

Depth 17-5/8”

Gas Inlet (Pipe) 3/8” Flair

Electrical - The unit comes equipped with a 5 foot (1.5 m)

3 pronged cord, for connection to an approved

115 VAC, 60 Hz , 5A (maximum) wall receptacle.

Vent Pipe: - 1-1/2 inch diameter schedule 40 PVC pipe, 40 feet

maximum equivalent length.

Common

28743-0-0711 Page 7

Page 8

INSTALLATION AND GENERAL SAFETY INFORMATION

General Information

This series is designed certied in accordance with American National Standard/CSA Standard Z21.88 as a Gas Fireplace Heater

to be installed according to these instructions.

Any alteration of the original design, installed other than as shown in these instructions will be the responsibility of the person and company making the changes, and will void the warranty. This product may not be used with any type of gas other than what is shown on the rating plate.

Important

All Correspondence should refer to complete Model Number, Serial Number and type of gas.

Installation

Installation, replacement, gas piping, gas utilization equipment or

accessories, and the repair and service of this equipment must

be performed by a qualied agency. The term “qualied agency” means any individual, rm, corporation or company which either in

person or through a representative is engaged in and is responsible for (a) the installation or replacement of gas piping or (b) the connection, installation, repair or servicing of equipment, who is experienced in such work, familiar with all precautions required and has complied with all the requirements of the authority having

jurisdiction.

• This installation must conform with local codes, or in the

absence of local codes, the National Fuel Gas Code,

NFPA 54/ANSI Z223.1.

• This appliance, when installed, must be electrically grounded

in accordance with local codes or. In the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70.

• Provide adequate clearances around the heater for servicing

and ensure there are no obstructions to the combustion air intake situated at the back of the heater. Refer to Pages 16 to

19.

• The Mantis Power-Vent High-Efciency Fireplace must be installed on a at, solid continuous surface (i.e. wood, metal,

concrete). Rough or uneven surfaces can cause vibration or humming in the heater.

• This appliance does need to be installed in such a way where

the heater can be removed for servicing the heat exchanger

and the ue that are located in the rear section of the heater.

• This appliance is equipped with a three-prong [grounding]

plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded receptacle, purchase an

adapter with two prongs and a wire for grounding.

Note: Under no circumstances should the appliance be installed

under conditions that would not allow for easy removal of the appliance to carry out routine inspection and service to the appliance.

Note: Where a mantel surround is being used on insert installa-

tions and zero clearance replace installations, the combustion air intake slot located in the top mantel surround must not be obstructed. This will allow combustion air to enter through the slot to the combustion air inlet located at the back of the heater.

Note: During initial ring of this unit, residual oil from the

heat exchanger may bake off and smoke may occur. Provide adequate ventilation to the area where the heater is installed to prevent triggering of smoke alarms. Refer to page 31 for more detail.

A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280, or when such a stan-

dard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS Z225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.0.

Installation on Combustible Flooring

If this appliance is to be installed directly on carpeting, tile, or other

combustible material, other than wood ooring, the appliance shall

be installed on a metal or wood panel extending the full width and depth of the appliance.

The base referred to above does not mean the re-proof base as

used on wood stoves. The protection is primarily for rugs that may be extremely thick and light-color tile that can discolor.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than 18 inches (457 mm) above the oor. The equipment shall be located, or protected, so it is not subject to physical damage by

vehicles.

Operation of Heater During Construction

The heater shall not be used during construction.

WARNING

Do not operate appliance with the glass front removed, or if it is cracked or broken. Replacement of the glass shall be performed by a licensed or quali-

ed service person

28743-0-0711Page 8

Page 9

GAS SUPPLY

All gas piping must be installed in compliance with local codes and

utility regulations. In the absence of local codes the installation

must comply with NFCG NFPA 54/ANSI Z223.1.

Note: Never use plastic pipe. Check to conrm whether your local codes allow copper tubing or galvanized.

Where permitted, exible gas connectors must be certied to the following standards: — ANS Z21.24 Appliance Connectors of Corrugated Metal Tub-

ing and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the author-

ity having jurisdiction. The state of Massachusetts requires that a exible appliance connector cannot exceed three feet in length.

A drip leg should be installed in the vertical gas supply pipe run to

the unit.

Manual Shut-off Valve

Some local regulations require the installation of a manual shut-off

valve and ground joint union external to the appliance. The shutoff should be accessible for service and/or emergency use. Consult the

local utility or gas supplier for additional requirements regarding the placement of the manual shut off valve. Compounds used on

threaded joints of gas piping shall be resistant to the action of liqueed petroleum gases.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8 inch N.P.T.

plugged tapping, accessible for test gauge connection, must be placed immediately upstream of the gas supply connection to the appliance.

2. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pres-

sure testing of that system at test pressures in excess of 1/2

psig.

3. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe

Inside Diameter

In Inches

Nat. L.P. Nat. L.P.

0-10 feet 1/2 3/8 1/2 3/8

10-40 feet 1/2 1/2 5/8 1/2

40-100 feet 1/2 1/2 3/4 1/2

100-150 feet 3/4 1/2 7/8 3/4

Tubing, Type L

Outside Diameter

In Inches

Leak Testing

WARNING - FIRE OR EXPLOSION HAZARD

Never test for leaks with an open ame. Check all

connections using a commercially available soap solution. A re or explosion may result causing property damage, personal injury or loss of life. Failure to follow the safety warnings exactly could result in serious injury, death or property damage.

After gas piping to the heater is complete, all connections must be

tested for gas leaks. This includes pipe connections at the main

gas valve, emergency shutoff valve and exible gas connectors (if

applicable). The soap and water solution can be applied on each

joint or union using a small paintbrush. If any bubbling is observed,

the connection is not sealed adequately and must be retightened. Repeat the tightening and soap check process until the bubbling ceases.

Important Note: When pressure testing the gas supply lines at pressures greater than ½ psig (14 in. w.c.), the gas supply piping system must be disconnected from the appliance to prevent damage to the gas control valve. If the test pressure is less than or equal to ½ psig (14 in. w.c.), close the manual shut-off valve.

28743-0-0711 Page 9

Page 10

VENT CLEARANCES

US Installation

A = Clearance above any grade,

B = Clearance to window or door

C = Clearance to permanently

D = Vertical clearance to venti-

E = Clearance to unventilated

F = Clearance of outside corner *

G = Clearance of inside corner *

H = Clearance to each side of

I = Clearance to service regulator

veranda, porch or balcony

that may be opened

closed windows

lated soft located above the terminal within a horizontal

distance of 2 ft (61 mm) from the center line of the terminal

soft

center line extended above

meter/regulator assembly

vent outlet

12 in (30 cm)

6 in (15 cm) for appliances ≤ 10,000 Btu/h (3 kW), 9 in (23

cm) for appliances > 10,000

Btu/h (3 kW) and ≤ 50,000 Btu/h (15 kW), 12 in (30 cm) for appliances > 50,000 Btu/h

(15 kW)

Figure 1

J = Clearance to non-mechanical

air supply inlet to building or the combustion air inlet to any other appliance

K = Clearance to a mechanical air

supply inlet

L = Clearance above paved

sidewalk or paved driveway located on public property †

M = Clearance under veranda,

porch deck, or balcony ¥

In accordance with the current ANSI Z223.1/NFPA 54, National

Fuel Gas Code

† A vent shall not terminate directly above a sidewalk or paved

driveway that is located between two single family dwellings and serves both dwellings.

¥ Permitted only if veranda, porch, deck or balcony is fully open

on a minimum of two sides beneath the oor.

* For clearances not specied in ANSI Z223.1/NFPA 54 or CSA

B149.1, refer to local codes.

6 in (15 cm) for appliances ≤ 10,000 Btu/h (3 kW), 9 in (23

cm) for appliances > 10,000

Btu/h (3 kW) and ≤ 50,000 Btu/h (15 kW), 12 in (30 cm) for appliances > 50,000 Btu/h

(15 kW)

3 ft (91 cm) above if within 10

ft (3 m) horizontally

28743-0-0711Page 10

Page 11

VENTING REQUIREMENTS

12” MIN TO GRADE.

(RECOMMENDED 12” MIN

TO MAX EXPECTEDSNOWLEVEL)

TYPICAL BOTH PIPES

6” Min

3” Min

24” Max

WARNING

This appliance must not be vented with any other appliances, even if that appliance is of the condensing type. Common venting can result in severe corrosion of other appliances or their venting and can allow combustion gases to escape through such applianc-

es or vents. Do not vent the heater into a replace

chimney or building chase.

WARNING

Upon completion of the installation, carefully in-

spect the entire ue system to assure it is properly

sealed. DO NOT use any vent material other than

what is specied in this manual. Leaks in the ue

system can result in serious personal injury or death due to exposure of ue products, including carbon monoxide.

The Mantis is classied as a “Category IV” appliance, which requires special venting materials and installation procedures. Installations can be Conventional (1-pipe) and Direct Vent (2-pipe). Venting must be completed with 1-1/2 inch diameter pipe. In selecting a location for installation, it is necessary to provide adequate clearances for servicing and proper installation.

All vent and combustion air pipes and ttings must be Schedule 40 PVC and meet the ANSI/ASTM Standard D1785. Cement must conform to ASTM Standard D2564.

The minimum distance from the center of the vent cap to the near-

est outside corner or obstruction is 12 inches. The ue outlet must be at least 12 inches from any opening which ue gases could enter the building. See Figure 1. The ue outlet must be a minimum

distance of 6 feet from any pressure regulator.

The bottom of the exhaust vent terminal and the air intake shall be located at least 12 inches above grade and must be vented outside. It is recommended the exhaust and intake be located 12 inches from the maximum snow level.

The ue pipe must be supported on horizontal vent runs. The ue pipe needs to be supported every 3 feet. All horizontal runs of the ue must be pitched ¼ inch per foot either towards the heater or

away from the heater. The minimum vent length protruding from outside the wall is 6 inches. For two-pipe installation, a minimum distance of 3 inches and maximum distance of 24 inches must be maintained between the pipes. See Figure 2.

Single ue (one-pipe) installations must have a minimum clearance of 2 inches on the back of the heater for combustion air.

Vent Freezing Protection

When the vent pipe is exposed to temperatures below freezing

(i.e. when it passes through unheated spaces, chimneys, etc.) The

pipe must be insulated with 1/2 inch thick sponge rubber insulation, Armaex-type insulation or equivalent. Insulating pipe is im-

portant to avoid condensate icing.

For proper operation, the ue exhaust must extend 6 inches from

the outside wall before applying an elbow.

Maximum Vent Length is 40 feet. The minimum vent length is 12 inches. Each 90° elbow used in the vent system will be

the equivalent to 3 feet, and each 45° elbow is equivalent to

1.5 feet, which should be added to the overall vent length. See

Table 1.

It is recommended that the Mantis Power-Vent High-Efciency

Fireplace be located on an exterior wall for ease of venting. The

ue exhaust pipe and inlet air pipe should be located between wall studs. The required opening for venting is 1-7/8 inch in diameter for 1-1/2 inch PVC pipe.

Table 1 - Equivalent Vent Length Example

EVL = Equivalent Vent Length

EVL must be greater than or equal to 1’ and less than or equal to 40’

EVL = 90º elbow + 4’ straight pipe + 45º elbow + 2’ straight pipe + 45º elbow + 3’ straight pipe = 15’

EVL = 3’

(90º elbow)

+ 4’

(straight pipe)

+ 1.5’

(45º elbow)

Note: If vent length requirements are not followed, the unit will not operate properly.

Figure 2

+ 2’

(straight pipe)

+ 1.5’

(45º elbow)

+ 3’

(straight pipe)

= 15’

28743-0-0711 Page 11

Page 12

VENT EXAMPLES FOR SINGLE FLUE

2’

5’

27’

VENT TERMINAL 90° ELBOW (NOT COUNTED)

90° ELBOW

3’

FIRST 90° ELBOW DOES NOT GET COUNTED WHEN WITHIN 6” OFF BACK OF HEATER

Figure 3 displays a single ue (one-pipe) installation. Because the distance from the heater to the rst elbow is more than 6 inches, the rst 90° elbow does need to be considered into the total vent

length. The equivalent length of the second 90° elbow also needs to be added to the total length, but the third elbow does not since

it is the ue terminal. The total horizontal vent length of the ue

system is 7 feet, and the total vertical length is 27 feet. The two 90°

H = 5’ + 2’ = 7’ V = 27’ (2) - 90° = 6’ Total = 40’

elbows are equivalent to 6 feet, bringing the total to 40 feet.

Figure 4 is an example of how the heater can be vented if the ue outlet is below the level of the oor.

Figure 4

Minimum Exterior Grade Dimension - Single Flue, Horizontal

Venting Below Floor

Figure 3

Single Flue - Horizontal Tall Vent Run

Example Calculation Max Vent Run 40 feet

28743-0-0711Page 12

Page 13

DIRECT VENT AND COLINEAR VENT EXAMPLES

12” MIN TO GRADE

(RECOMMENDED 12” MIN.

TO MAX EXPECT SNOW LEVEL)

6” MIN.

9” MIN.

3” MIN.

2” MIN.

3” MIN.

12” MIN. TO ROOF (RECOMMENDED 12”

MIN TO MAX. EXPECTED

SNOW LEVEL)

PTRAP

90° ELBOW

3’

COLINEAR ADAPTER

5’

10’

FIRST 90° ELBOW DOES NOT GET COUNTED WHEN WITHIN 6” FROM THE BACK OF HEATER

H=5’+6’=11’ V=10’ +10’ =20’ (3) 90°=9’

=40’TOTA L

6’

90° ELBOW

3’

10’

6” MIN.

12” MAX.

SUPPORT

OUTSIDE

WALL

1/2” ARMAFLEX INSULATION OR EQUIVALENT (IF REQUIRED)

12” ABOVE

MAXIMUM

EXPECTED

SNOW LEVEL

Figure 5 displays a two-pipe installation. Because the distance

from the heater to the rst elbow is more than 6 inches, the rst 90°

elbow does need to be considered into the total vent length. The equivalent length of the second 90° elbow also needs to be added to the total length. The third elbow also needs to be included. The equivalent length of the PTrap does not need to be added since it is the termination. The total horizontal vent length of the ue system is 11 feet, and the total vertical length is 20 feet. The three 90° elbows are equivalent to 9 feet, bringing the total to 40 feet.

Note: Exhaust must be a minimum of 3 inches above air intake inlet.

Note: The exhaust must be a minimum of 3 inches above the inlet

air pipe. The ue must be at least 12 inches from the roof line, and

it is recommended to be at least 12 inches above the maximum expected snow level as indicated in Figures 5 through 8.

Calculation example of vent run maximum 40 feet

Figure 5

28743-0-0711 Page 13

Figure 6

Figure 7

Page 14

DIRECT VENT AND COLINEAR VENT EXAMPLES

COLINEAR ADAPTER

12” MINIMUM TO GRADE

RECOMMENDED 12” MINIMUM TO

MAXIMUM EXPECTED SNOW LEVEL

REAR SHROUD

SINGLE FLUE ADAPTER

FLASHING

REQUIRED

REQUIRED HEIGHT IS 12”

MINIMUM. IT IS RECOMMENDED

TO BE 12” ABOVE THE

EXPECTED SNOW LEVEL.

AIR INTAKE

PTRAP,290 EBLOWS

(SUPPLIED BY INSTALLER).

PTRAP TO FACE AWAY FROM ROOF.

3” -24”

PVC CEMENT

Figure 8

In direct vent applications, a minimum distance between the two

pipes is 3 inches and the maximum distance is 24 inches. The ue

exhaust and air inlet can be terminated with either a PTrap or two 90° elbows as shown in Figures 9,12 and 13. The Vertical Termination Cap (Part number PVVTC) can also be used.

Figure 10 - PVVTC Vertical Termination Cap

Figure 11

Vertical termination cap used with 1-1/2 inch PVC

pipe installation.

Cap also used with colinear transition plate.

Figure 9

28743-0-0711Page 14

Page 15

COLINEAR TRANSITION VENT KIT

AIR INTAKE PTRAP OR290° ELBOWS SUPPLIED BY INSTALLER

TRANSITION PLATE

PVC CEMENT

OUTDOOR SEALER REQUIRED

OPTIONAL

TERMINATION CAP

3” MIN.

REQUIRED HEIGHT IS 12” MINIMUM. IT IS RECOMMENDED TO BE 12” ABOVE THE MAXIMUM EXPECTED SNOW LEVEL.

AIR INTAKE PTRAP OR290° ELBOWS SUPPLIED BY INSTALLER

TRANSITION PLATE

PVC CEMENT

OUTDOOR SEALER REQUIRED

3” MIN.

EXHAUST PTRAP OR 2 90° ELBOWS SUPPLIED BY INSTALLER

REQUIRED HEIGHT IS 12” MINIMUM. IT IS RECOMMENDED TO BE 12” ABOVE THE MAXIMUM EXPECTED SNOW LEVEL.

FLUE ADAPTOR

PLASTIC GASKET

INSTALL FOAM GASKET

THREADED CONNECTOR

The Colinear Transition Kit (Part number PVCT) is available and

can be used to secure the ue and inlet pipes from the Mantis.

When venting vertically, the exhaust pipe termination must be a minimum of 3 inches above the air inlet.

Figure 12

The ue can be terminated with a PTrap or two 90° elbows. The

Vertical Termination Cap (Part number PVVTC) can also be used

to terminate the ue pipe when using the Colinear Transition Kit.

Figure 13

Installation of the Colinear Transition Plate

1. Attach the plate to chimney chase, at roof, or outside wall

with four (4) screws. Use outdoor sealant to seal the transition plate to the surface.

2. Both inlet air pipe and ue exhaust pipe must be 12 inches

from the roof line, and it is recommended to be 12 inches

above the maximum snow line. Also refer to local codes. See

Figures 12 and 13.

VENT ADAPTOR KITS

The Vent Adaptor Kits provide a transition from the appliance to the ue and inlet pipes. Colinear Adaptor (part number PVCA) provides a transition for the inlet air. When using the ue adapter, use

3. Attach the ue and inlet air pipes to the transition plate. Use

the appropriate primer and cement to permanently bond the

joints and the pipes to the transition plate.

the appropriate primer and cement to permanently bond the joints

and the pipes. The inlet air pipe does not need to be cemented.

Figure 14

28743-0-0711 Page 15

Figure 15

Page 16

ROUGH FRAMING DIMENSIONS

ACCESS

PANELS

ACCESS PANELS

Figure 16

Single Vent

A 8-1/2” minimum* 8-1/2” minimum* 7-3/4” minimum 12-3/4” minimum

Bay Window Mantis with

PV-4H

Short Top Cover Kit

* When using a 90° elbow on the ue exhaust.

Single Vent

A 13-1/2” minimum* 13-1/2” minimum* 12-5/8” minimum 17-7/8” minimum

Bay Window Mantis with

PV-2H

Slim Top Cover Kit

* When using a 90° elbow on the ue exhaust.

Figure 17

Direct Vent and

Colinear Vent

Coaxial Vent Flex Vent

25-1/4” minimum

27” maximum when using PVE-1 or PVE-2 Surround Kits

28-1/2” minimum, 33” minimum recommended for service

34-1/2” maximum when using PVE-1 Surround Kit

37” maximum when using PVE-2 Surround Kit

Direct Vent and

Colinear Vent

Coaxial Vent Flex Vent

25-1/4” minimum

27” maximum when using PVE-1 or PVE-2 Surround Kits

28-1/2” minimum, 33” minimum recommended for service

34-1/2” maximum when using PVE-1 Surround Kit

37” maximum when using PVE-2 Surround Kit

A 19-1/2” minimum* 19-1/2” minimum* 18-1/2” minimum 23-3/4” minimum

Fireplace Mantis

* When using a 90° elbow on the ue exhaust.

Single Vent

Direct Vent and

Colinear Vent

Coaxial Vent Flex Vent

25” minimum

27-3/4” maximum when using FGK28 Surround Kit

28-1/2” maximum when using FFK28 Surround Kit

29-1/2” maximum when using FIK28 Surround Kit

32” maximum when using FWK28 Surround Kit

28-1/2” minimum, 31” recommended for service

33” maximum when using FGK28 Surround Kit

34” maximum when using FFK28 Surround Kit

37” maximum when using FIK28 Surround Kit

34” maximum when using FWK28 Surround Kit

28743-0-0711Page 16

Page 17

INSERT INTO MASONRY FIREPLACE

Figure 18

Bay Window Mantis with PV-4H

Short Top Cover Kit

* When using a 90° elbow on the ue exhaust.

Bay Window Mantis with PV-4H

Slim Top Cover Kit

* When using a 90° elbow on the ue exhaust.

Single Vent

A 8-1/2” minimum* 8-1/2” minimum* 12-3/4” minimum

A 13-1/2” minimum* 13-1/2” minimum* 17-7/8” minimum

27” maximum when using PVE-1 or PVE-2 Surround Kits

28-1/2” minimum, 33” minimum recommended for service

34-1/2” maximum when using PVE-1 Surround Kit

37” maximum when using PVE-2 Surround Kit

Single Vent

27” maximum when using PVE-1 or PVE-2 Surround Kits

28-1/2” minimum, 33” minimum recommended for service

34-1/2” maximum when using PVE-1 Surround Kit

37” maximum when using PVE-2 Surround Kit

Direct Vent and

Colinear Vent

25-1/4” minimum

Direct Vent and

Colinear Vent

25-1/4” minimum

Flex Vent

Fireplace Mantis

* When using a 90° elbow on the ue exhaust.

28743-0-0711 Page 17

Single Vent

A 19-1/2” minimum* 19-1/2” minimum* 23-3/4” minimum

27-3/4” maximum when using FGK28 Surround Kit

28-1/2” maximum when using FFK28 Surround Kit

29-1/2” maximum when using FIK28 Surround Kit

32” maximum when using FWK28 Surround Kit

28-1/2” minimum, 31” recommended for service

33” maximum when using FGK28 Surround Kit

34” maximum when using FFK28 Surround Kit

37” maximum when using FIK28 Surround Kit

34” maximum when using FWK28 Surround Kit

Direct Vent and

Colinear Vent

25” minimum

Flex Vent

Page 18

BAY WINDOW MANTIS CLEARANCE TO COMBUSTIBLES

ACCESS PANEL

12”

18”

24”

8”

6”

4”

COMBUSTIBLE TRIM AND MANTELS

ALLOWED IN SHADED AREA

40”

CEILING

Figure 19

Freestanding Clearances

A Rear Wall to Heater 2” (1-1/4” for coaxial venting)

B Side Wall to Heater 0” (4” recommended for door clearance)

C Corner Installation 0”

Coaxial Venting Installation Shown

Single Flue requires surround for combustion air.

Figure 21

Figure 20

Note: The Mantis Power-Vent High-Efciency Fireplace has been tested and approved for zero clearance to combustible materials. It

is recommended that clearances as listed above should be maintained to allow for removal of the product for servicing.

Mantel and Ceiling Clearances

Figure 22

28743-0-0711Page 18

Page 19

FIREPLACE MANTIS CLEARANCE TO COMBUSTIBLES

6-1/4”

MIN

ACCESS PANEL

12”

18”

24”

8”

6”

4”

COMBUSTIBLE TRIM AND MANTELS

ALLOWED IN SHADED AREA

44-3/4”

CEILING

4-3/4”

ACCESS PANEL

Figure 23 Figure 25

Figure 24

Insert Clearances

A Rear Wall to Heater 2” (1-1/4” for coaxial venting)

B Side Wall to Heater 0”

C Corner Installation 0”

Note: The Mantis Power-Vent High-Efciency Fireplace has been tested and approved for zero clearance to combustible materials. It

is recommended that clearances as listed above should be maintained to allow for removal of the product for servicing.

28743-0-0711 Page 19

Mantel and Ceiling Clearances

Figure 26

Page 20

BAY WINDOW MANTIS SPECIFICATIONS

28”

33-3/4”

8-5/8”

17-5/8”

12-1/4”

OPTIONAL PEDESTAL

(MUST BE INSTALLED ON

HEATER PRIOR TO APPLIANCE

INSTALLATION)

28”

25-1/4”

27-3/4”

FLUE OUTLET

16-15/16”

17-5/8”

3-9/16” (9.0cm)

6”

17-13/16”

6-1/2”

PVE-1 or PVE-2

(SURROUND)

PVVK-CFA

FLEX VENT

PVVK-SH

VENT ADAPTOR

11-3/32”

12-3/4”

6-1/2”

PV-4H

(SHORTTOP

COVER KIT)

PV-2H

(SLIM TOP

COVER KIT)

Heater with Pedestal and Single Flue Adaptor

Figure 27

Heater with Slim and Short Top Cover Kits and Flex Kits.

Heater without pedestal

Figure 28

Figure 29

28743-0-0711Page 20

Page 21

35-7/16”

38”

LOUVER

29-3/4”

5-15/16”

23-13/16”

10-1/8”

6-13/16”

PV-4H

(SHORTTOP

COVER KIT)

3-9/16”

16-15/16”

BAY WINDOW MANTIS SPECIFICATIONS - (continued)

35-7/16”

OR 38”

LOUVER

29-3/4”

5-15/16”

23-13/16”

PV-2H

(SLIM TOP

COVER KIT)

11-5/16”

3”

3-9/16”

6”

FLUE OUTLET

AIR INLET

ELECTRIC

CORD

13/16”

1”

7-5/16”

2-13/16”

1-7/16”

3-9/16”

1-1/2”

6-1/8”

FLEX HOSE OPENING

Fireplace Insert with Mantel Surround with PV-2H Slim Top Cover Kit

Figure 30

Fireplace Insert with Mantel Surround with PV-4H Short Top Cover Kit

28743-0-0711 Page 21

Figure 31

Rear View

Figure 32

Page 22

35”

33-7/16”

35”

29-3/8”

PVVK-CFA

FLEX VENT KIT

23-1/2”

24-3/4”

MIN.

6-1/2”

FIREPLACE MANTIS SPECIFICATIONS

17-3/16”

3-9/16”

FLUE OUTLET

24-3/4” MIN

Figure 33

Heater with Flex Vent

Figure 34

Figure 35

Heater In Wall - 35 Inch Picture Frame Surround

FWK28(BL,CM,HP,SS) - Contains surround, hood, and lower

front

Figure 36

Heater - 35 Inch Surround Kit

FFK28(BL,CM,HP,SS) - Contains surround, hood, & lower front

28743-0-0711Page 22

Page 23

FIREPLACE MANTIS SPECIFICATIONS

38”

30-7/8”

FLUE

OUTLET

AIR INLET

ELECTRIC

CORD

FLEX HOSE OPENING

1-1/8”

7-5/16”

4-3/16”

2-5/8”

6-1/8”

3-9/16”

13/16”

1”

28”

4”

8”

Figure 37

Heater - 38 Inch Surround

FIK28(BL,CM,HP,SS) - Contains surround, hood, & lower front

Figure 39

Clearance for Access Panel In-Wall Units

See Gas Connection Instructions.

28743-0-0711 Page 23

Figure 38

Page 24

GAS CONNECTION INSTALLATION

PUSH IN PLUG

ACCESS PLATE

FLEXIBLE GAS LINE

CAUTION

The gas supply line to the heater must be installed under conditions which will allow for easy removal of the heater from its location for servicing of the heat-

er. For replace insert installation, incorporate a loop into the exible gas line.

Under no circumstances should the gas supply line to the appliance be installed in a way that would prevent the appliance from being serviced or inspected.

GAS SUPPLY LINE TO HEATER

1. Pull the factory installed exible gas line through the hole in

the back panel. See Figures 40 and 41.

2. Connect the gas supply line to exible gas hose. Ensure that exible gas hose is not kinked after tting gas supply line. Any excess exible line can be pushed back into the heater.

3. Place rubber grommet that is supplied in hardware packet

over the exible gas line and secure in the hole in the back of

the appliance.

Figure 40 - Fireplace Mantis

Gas Connection - In-Wall Units - Fireplace Mantis ONLY

1. Remove the access plate on the left side of the cabinet by removing three screws as shown in Figure 42. Put the screws aside.

2. Push the factory supplied exible gas line through the access

hole on the side.

3. Remove the knockout from the access plate and insert the

exible gas line through the hole.

4. Secure the access plate to the cabinet with three screws removed in Step 1.

5. A plastic push in plug is supplied in the hardware package, insert the plug into the 1-3/8 inch hole in the back of the unit.

6. Insert the rubber grommet into the hole in the access plate to

protect the exible gas line.

Figure 41 - Bay Window Mantis

Figure 42

Gas Connection, Fireplace Mantis In-Wall Units

28743-0-0711Page 24

Page 25

BAY WINDOW MANTIS LOG SET INSTALLATION INSTRUCTIONS

PLATE - LOG SUPPORT

FRONT HOT SURFACE IGNITOR

REAR HOT SURFACE IGNITOR REAR FLAME SENSOR

FRONT FLAME SENSOR

REAR BURNER

FRONT BURNER

REAR LEFT LOG (A)

TOP RIGHT LOG (G)

FRONT RIGHT LOG (E)

CENTER LOG (D)

FRONT LEFT LOG (C)

TOP LEFT LOG (F)

REAR RIGHT LOG (B)

Log Installation

Positioning of the logs is critical to the safe and clean operation of this heater. If the logs are not placed in the proper position, the appliance can soot, and create an unsafe operating condition.

CAUTION

Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling the logs, wash your hands gently with soap and water.

1. To access the log set parcel, lift off the top panel.

2. Pivot the left and right panels open.

3. Unhook the main door latches located on the right and left side of the heater, then remove the door.

4. Connect the Rear Left Log (A) and the Rear Right Log (B).

Place the logs behind the rear burner. The logs should be all

the way to the back of the rebox. See Figure 43.

5. Place the Front Left Log (C) into the groove on (A) Log, and locate into the left corner of rebox. See Figure 44.

6. Place the Middle Log (D) over the ame sensors that are located in the middle of the rebox. The Middle Log (D) should be positioned as far to the right side of the rebox as pos-

sible.

7. Locate the Front Right Log (E) in the right front corner of rebox. The Front Right Log (E) should t snug into the corner.

8. Place the Top Left Log (F) onto the pin on (A) Log. The “legs”

of (F) Log will rest on (D) Log. See Figure 45.

9. Place the Top Right Log (G) onto the pin on (B) Log. The “legs” of (G) Log will rest on (E) Log.

10. Place the door assembly on the heater and secure with the main door latches that are located on right and left sides of the heater.

11. Close the left and right panels.

12. The installation of the log set is complete.

13. Verify that the logs are not in contact with the ame sensor. Interference with the ame sensor will effect the operation.

Log Placement

Figure 44

Log Placement

Figure 45

Log Placement

Figure 43

28743-0-0711 Page 25

Firebox Layout

Figure 46

Log Assembly

Figure 47

Page 26

FIREPLACE MANTIS LOG SET INSTALLATION INSTRUCTIONS

REAR LOG SUPPORT

FRONT LOG SUPPORT

FIREBOX BOTTOM

REAR HOT SURFACE IGNITOR

REAR FLAME SENSOR

REAR BURNER

RIGHT REAR

LOG SUPPORT

SHELF

FRONT BURNER

FRONT FLAME SENSOR

FRONT HOT SURFACE IGNITOR

LEFT REAR

LOG SUPPORT

SHELF

Rear Log

Left Log

Right Log

Middle Log

Front Left Log

Front Right Log

Left Top Log

Right Top Log

Log Installation

CAUTION

Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling the logs, wash your hands gently with soap and water.

Log Placement

1. Place the Rear Log (A) onto the rear log support. The notch in the Rear Log ts over the rear igniter. The Rear Log (A) should be all the way to the back of the rebox and as far to

the left side as possible. See Figure 48.

2. Place Left Log (B) on the left rear log support shelf. The charred portion of the log must face inward. See Figure 48.

3. Place the Middle Log (D) on front log support between the front and back burners.

4. Place the Front Right Log (F) on the right side of rebox bottom. The notch in the bottom of Front Right Log ts over the front ame sensor. The log should be positioned fully forward.

See Figure 48.

5. Place the Front Left Log (E) on left side of the rebox bottom. The notch in bottom of Front Left Log ts over front Igniter.

The log should be positioned full forward.See Figure 49.

6. Place the Right Log (C) on the right rear log support shelf. The

top of log rests on Rear Log (A) and bottom of log rests on

Firebox bottom. The charred portion of log must face inward. See Figure 49.

7. Place the Left Top Long Log (G) on the pin on Left Log (B).

The upper left leg of Left Top Log will rest on Rear Log (A).

The upper right leg of Left Top Log will rest on Middle Log (D).

8. Place the Right Top Long Log (H) on the pin on the Right Log (C). The bottom left leg of Right Top Log (H) will rest in the

indentation on the right side of the Middle Log (D). The bottom

right leg of the Right Top Log (H) will rest in the indentation in

the Front Right Log (F).

9. Verify that the logs are not in contact with the ame sensor. Interference with the ame sensor will effect the operation.

Log Placement

Figure 48

Log Placement

Figure 49

Log Assembly

Figure 50

Firebox Layout

Figure 51

28743-0-0711Page 26

Page 27

WIRING

RECEIVER

WHITE

PURPLE

YELLOW

INDICATOR

SWITCH

+ -

WHITE

BLACK

L. BRN. THERM (3)

R. BRN. THERM (4)

14 WAY RIBBON TO CONTROL MODULE

PURPLE

YELLOW

WHITE

BLUE

TRANSFORMER

RED

BLACK

WARNING

Potential risk of re, electric shock, and personal injury. Take precautions to reduce such risks.

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

This appliance is equipped with a three-prong [grounding]

prongs and a wire for grounding, can be purchased.

Proper line voltage polarity must be maintained in order for the control system to operate correctly. Verify the incoming neutral line is connected to the white wire and the incoming “hot” line is connected to the black wire. The heater will not operate properly unless the polarity and ground are correct.

Instructions for connecting controllers can be found on page 39.

28743-0-0711 Page 27

Figure 52

Figure 53

Page 28

START UP CHECK LIST

WARNING

BEFORE OPERATING THIS APPLIANCE, CAREFULLY READ THE FOLLOWING.

1. Verify the gas line service does not exceed 10.5 in. w.c. and is not below 5.0 in. w.c. for natural gas, nor exceeds

13.0 in. w.c. or is below 11.0 in. w.c. for LP gas.

2. Check and inspect the appliance for gas leaks. In the event of gas leaks, cut off the gas supply to the heater immediately and call your gas supplier. Verify the gas line has been purged.

3. Verify that all exhaust and inlet air pipes are unobstructed and

properly joined.

4. Visually verify the burners are free of dust and debris. See Figures 46 and 51.

5. Check and verify that logs are place correctly. See pages 25 to 26. The logs must be in the correct position or the heater will not operate correctly.

DO NOT light heater without the logs installed, the heater will not operate properly.

6. Verify that all panels are secured in place and that the glass assembly door has been locked in position.

7. Verify the two burner switches are in the OFF position before

applying power and the main power switch.

8. After verifying and checking all the above points, proceed to

lighting instructions. Refer to Page 29.

9. Verify that the polarity of the connections are correct and the line voltage power leads are secure.

Note: If using a surround, verify it is installed per the instructions included with the kit.

28743-0-0711Page 28

Page 29

LIGHTING INSTRUCTIONS

OFF

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

A. BEFORE LIGHTING smell all around the appliance

area for gas. Be sure to smell next to the oor be-

cause some gas is heavier than air and will settle on

the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instructions.

• If you can not reach your gas supplier, call the re

department.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this la-

bel.

2. Set the thermostat, if used, to the lowest setting.

3. Turn off all electric power to the appliance. Turn off

electrical control switches to “O.”

4. This appliance is equipped with an ignition device that automatically lights the burner. Do not try to light the burner by hand.

5. Remove the front access panel below the glass door by pulling both sides forward simultaneously.

6. Turn gas line valve to “ON.”

7. Wait ve (5) minutes to clear out any gas. Then smell for gas, including near the oor. If you smell gas, STOP! Follow “A” in the safety information above. If you do

not smell gas, go to the next step.

B. Use the on-the-wall switch or remote con-

trol switch to turn the gas control on/off. Any attempted repairs or adjustments should be performed by a qualied service technician. Applying force or attempted repair may result in a re

or explosion.

C. Do not use this appliance if any part has been under

water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

8. Turn on electric power to the appliance. Turn on electric control switches to “ ”.

9. Replace the front access panel, press both sides of the panel until both lock position.

10. Set thermostat to desired setting (if available).

11. If the appliance will not operate, follow the instructions

“TO TURN OFF GAS TO APPLIANCE,” and call your

service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. STOP! Read the safety information above.

2. Set the thermostat, if used, to the lowest setting.

3. Turn off electric power to the appliance.

28743-0-0711 Page 29

4. Remove front access panel.

5. Turn gas line valve to “OFF.”

6. Replace front access panel.

Page 30

START UP AND ADJUSTMENTS

RECEIVER LOCATION

ADJ. LEARN

REMOTE ONOFF

FRONT BURNER SWITCH

REAR BURNER SWITCH

ECONOMY DISPLAY BUTTON

= OFF =ON

A. With main electrical power to the heater turned off, install 4

AA sized 1.5V batteries into the remote receiver. The remote

receiver is located inside the heater, mounted to the top of the blower housing and secured with hook and loop tape. See Figure 54. Set up receiver and remote per instructions on pages 32 - 37.

Figure 54

B. Turn on the main electrical power to the heater and turn the

main burner switch to the ON position. See Figure 55. Verify

power is on by checking if there is power to the circuit board. If the unit has power, the power light will be illuminated.

Sequence of Operations – Front and Back Burners

1. The Display Panel will be energized, and the lights for the front burner and back burner will ash.

2. The inducer will activate immediately and will prove the pressure switch within 16 seconds. This will initiate the ignition sequence.

3. The rear igniter (HSI) will energize and start to glow red.

4. Within 3 to 5 seconds, the gas valve will open and ignite the

rear burner. The ame sensor will verify the ame is present

within 2 to 5 seconds.

5. The igniter for the front burner will energize 5 to 7 seconds after the ame is established on the rear burner.

6. The gas valve will open to ignite the front burner within 3 to

5 seconds. The ame sensor will verify the ame is present

within 2 to 5 seconds.

7. As the Mantis warms up, the circulating blower will activate,

starting on Low speed. The Low Blower L.E.D. will light when the blower turns on.

8. As the Mantis continues to operate, the speed of the circulating blower will increase, and the L.E.D. for Medium and High

will appear.

Figure 55

C. Turn on the main gas supply. D. Turn both burner switches on to ignite both the front and rear

burners. Burner switches must remain in the ON position for

the remote to function. See Figure 56.

E. The Display Panel board should be energized, and the power

light will be illuminated.

Figure 56

CAUTION

When switching from one burner to the other burner,

be sure to rst turn “ON” the desired burner before

turning “OFF” the burner that is operating. Failure to follow this sequence may result in the heater needing to be reset. See page 40 - Resetting the Heater.

28743-0-0711Page 30

Page 31

START UP AND ADJUSTMENTS

Sequence of Operations – One Burner Only

1. The Display Panel will be energized, and the light for either the front burner or back burner will ash, corresponding to

which burner switch is activated.

2. The inducer will activate immediately and will prove the pressure switch within 16 seconds. This will initiate the ignition sequence.

3. The igniter (HSI) will energize and start to glow red.

4. Within 3 to 5 seconds, the gas valve will open and ignite the

burner. The ame sensor will verify the ame is present within

2 to 5 seconds.

5. The igniter for the front burner will energize 5 to 7 seconds after the ame is established on the burner.

6. As the Mantis warms up, the circulating blower will activate,

starting on Low speed. The Low Blower L.E.D. will light when the blower turns on.

7. As the Mantis continues to operate, the speed of the circulating blower may increase.

High Altitude

The Mantis can be installed to altitudes up to 10,000 feet in the U.S., and up to 4,500 feet in Canada. The installation must meet

the requirements of the National Fuel Gas Code or local jurisdictions. A high altitude kit is needed for installation above 2,000 feet. See the instructions provided with the Mantis High Altitude Kit for

derate instructions.

Humidier Operation

When the heater has been running, the humidier L.E.D. (Figure 57) may turn on to signal that the pump has been acti-

vated. Refer to Page 38 - Automatic Humidier Operation.

Paint Curing - First Firing

The Mantis Power-Vent High-Efciency Fireplace has been painted with the high quality heat resistant silicon paint. To ensure that the paint is properly cured, allow the heater to operate with both

burners on, for approximately 1 hour. During the initial ring of the

appliance, it is common for smoke to appear.

CAUTION

DO NOT touch the surface of the heater. The paint will soften during the initial operation, and will harden over time. Once the paint is cured, it will not soften again.

Figure 57

Shut Down Instructions

To turn the heater off, simply push “OFF” on the remote or switch the burner switch(es) to the “OFF” position. See Figure 56. DO NOT cut the main electrical power to the heater.

The circulating blower will continue to operate after the burners are turned off. The blower will stop automatically once the heater has cooled down.

Checking Manifold Pressure

Both Propane and Natural gas valves have a built-in pressure regulator in the gas valve. Natural gas models will have a manifold pressure of approximately 4.0 in. w.c. at the valve outlet, with the inlet pressure to the valve at 5.0 in. w.c. to 10.5 in. w.c. Propane gas models will have a manifold pressure approximately 7.0 in. w.c. at the valve outlet, with the inlet pressure to the valve from

11.0 in. w.c. to 13.0 in. w.c.

A 1/8 inch N.P.T. plugged tapping, accessible for test gauge connection, is located on the outlet side of the gas control.

Blower Operation

The circulating air blower will automatically engage and increase in speed depending on the operation of the burners. See Figure

56. In most circumstances, the circulating blower will start 3 to 5

minutes after ignition of the burners.

Once the heater is turned off or the call for heat has been satised,

the circulating blower will continue to run. The blower will automatically turn off once the heater has cooled down.

• To prevent triggering of smoke alarms, supply proper ventila-

tion to the room where the unit is installed.

• During initial ring of logs, an odor will occur as the logs are

curing. It is also common for the burner to burn with a yellow

ame.

• DO NOT clean the heater with any caustic or abrasive clean-

ing solutions. This will damage the surface.

• Any damage to the painted surfaces should be repaired only with authorized paint available from your Mantis Dealer.

28743-0-0711 Page 31

Page 32

FRBTC REMOTE INSTRUCTIONS

INTRODUCTION

This remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. This all battery system operates independently of household current. The system operates on radio frequencies with a non-directional signals. The SYSTEM’s operating range is approximately 20 feet range. The system operates on one of 1,048,576 security codes that are programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY SECTION under TRANSMITTER section and THERMO SAFETY SECTION

under REMOTE RECEIVER section. These signal/temperature safety features shut down the replace system when a

potentially unsafe condition exists.

This remote control SYSTEM offers the user a battery-operated remote control that operates most millivolt gas valves used in some heater rated gas logs, gas

replaces and other gas heating appliances.

The transmitter operates on (2) 1.5V AAA batteries.

It is recommended that ALKALINE batteries always be used for longer battery

life and maximum operational performance.

Before using the transmitter, install the (2) AAA transmitter batteries into the

battery compartment. (Use caution that batteries are installed in the proper direction)

KEY SETTINGS

• ON - Operates unit to on position, Manually ON.

• OFF - Operates unit to off position, Manually OFF.

• MODE - Changes unit from manual mode to thermo mode.

• SET - Sets temperature in thermo mode.

1. DISPLAY Indicates CURRENT room temperature .

2. °F OR °C Indicates degrees Fahrenheit or Celsius.

3. FLAME Indicates burner/valve in operation.

4. ROOM Indicates remote is in THERMO operation.

5. TEMP Appears during manual operation.

6. SET Appears during time the of setting the desired tem-

perature in the thermo operation.

28743-0-0711Page 32

Page 33

FRBTC REMOTE INSTRUCTIONS

SETTING °F / °C SCALE The factory setting for temperature is °F. To change this setting to °C,

rst

• Press the ON key and the OFF key on the transmitter at the

same time this will change from °F to °C. Follow this same procedure to change from °C back to °F.

MANUAL FUNCTION

To operate the system in the manual “MODE” does the following.

ON OPERATION

Press the ON key the appliance ame will come on. During this time the LCD screen will show ON, after 3 seconds the LCD screen will

default to display room temperature and the word TEMP will show.

(Flame icon will appear on LCD screen in on mode) OFF OPERATION

Press the OFF key the appliance ame will shut off. During this time the LCD screen will show OF, after 3 seconds the LCD screen will

default to display room temperature and the word “TEMP” will also show on the screen.

THERMOSTAT FUNCTION

SETTING DESIRED ROOM TEMPERATURE

This remote control system can be thermostatically controlled when

the transmitter is in the THERMO mode (The word ROOM must be displayed on the screen). To set the THERMO MODE and DE-

SIRED room temperature, Press the MODE key until the LCD screen shows the word ROOM, then the remote is in the thermostatic mode. Press and hold the SET key until the desired set temperature is reached. (By pressing and holding the set key the LCD screen set numbers will increase from 45° to 99° then restart over at 45°) Next release the SET key. The LCD screen will display the set temperature

for 3 seconds and the LCD screen will ash the set temperature for 3

seconds, then the LCD screen will default to display the room temperature.

TO CHANGE THE SET TEMPERATURE

Press and hold the SET key until the desired set temperature is reached. (By pressing and holding the set key the LCD screen set numbers will increase from 45° to 99° then restart over at 45° ) Next release the SET key. The LCD screen will display the set temperature

for 3 seconds, then will ash the set temperature for 3 seconds, then

the LCD screen will default to display the room temperature. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation.

NOTE: The highest SET temperature is 99° Fahrenheit (32° Cel- sius) and the lowest temperature is (45° Fahrenheit (6° Celsius).

28743-0-0711 Page 33

Page 34

FRBTC REMOTE INSTRUCTIONS

OPERATIONAL NOTES:

The Thermo Feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE. This variation is called the “SWING” or TEMPERATURE DIFFERENTIAL. The normal operating cycle of an appliance may be 2-4 times per hour depending on how well the room or home is

insulated from the cold or drafts. The factory setting for the “swing number” is 2. This represents a temperature variation of +/- 2°F (1°C) between SET temperature and ROOM temperature, which determines when the replace will be activated. This function is pre-set at the factory.

The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen to show while the signal is

being sent. Upon initial use, there may be a delay of three seconds before the remote receiver will respond to the transmitter. This is part of the system’s design.

REMOTE RECEIVER

IMPORTANT

THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE

AMBIENT TEMPERATURES DO NOT EXCEED 130° F.

The remote receiver operates on 4 AA-size 1.5V batteries. It is recommended that ALKALINE batteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential for proper

operation of the remote receiver. The remote receiver houses the microprocessor that responds to commands from the transmitter to control system op-

eration. It emits one beep when it receives an ON or OFF command manually, but no beep when cycling on and off automatically in THERMO mode. The remote receiver has a 3-position slide switch for selecting the MODE of operation: ON/ REMOTE/OFF

• With the slide switch in the ON position (toward the LEARN button), the system will remain on until the slide switch is placed in the OFF or REMOTE position.

• With the slide switch in the REMOTE position (centered), the system will

only operate if the remote receiver receives commands from the transmitter.

• With the slide switch in the OFF position (away from the LEARN button),

the system is off.

• It is suggested that the slide switch be placed in the off position if

you will be away from your home for an extended period of time. If the remote receiver is mounted out of children’s reach, placing the slide switch in the OFF position also functions as a safety “lock-out” by both turning the system off and rendering the remote receiver inoperative.

28743-0-0711Page 34

Page 35

FRBTC REMOTE INSTRUCTIONS

CP (CHILDPROOF) FEATURE

This ECS remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to “LOCK-OUT” operation of the appliance, from the TRANSMITTER.

SETTING “LOCK-OUT” –(CP)

• To activate the “LOCK-OUT” feature, press and hold the ON button and the MODE button at the same time for 5 seconds. The letters

CP will appear in the TEMP frame on the LCD screen.

• To disengage the “LOCK-OUT”, press and hold the ON button and the MODE button at the same time for 5 seconds and the letters

CP will disappear from the LCD screen and the transmitter will return to its normal operating condition.

• To verify that transmitter is in the CP lock-out mode press any key and the LCD screen will show “CP”

NOTE: If the appliance is already operating in the ON or THERMO MODES, engaging the “LOCK-OUT” will not cancel the operating MODE. Engaging the “LOCK-OUT” prevents only the manual operation of the TRANSMITTER. If in the auto modes, the THERMO operation will continue to operate normally. To totally “LOCK-OUT” the operation of the TRANSMITTER’S operating signals; the transmitter’s MODE must be set to OFF.

THERMO UPDATING FEATURE –TRANSMITTER – (T/S –TX)

This ECS remote control has a THERMO UPDATING Feature built into its software. The THERMO UPDATING Feature operates in the following manner, but only in the THERMO MODES:

The transmitter normally reads the ROOM temperature every 2 minutes checking the ROOM temperature against the SET temperature and then sends a signal to the receiver.

COMMUNICATION – SAFETY – TRANSMITTER – (C/S – TX)

This ECS remote control has a COMMUNICATION –SAFETY function built into its software. It provides an extra margin of safety when the TRANSMITTER is out of the normal 20 foot operating range of the receiver.

The COMMUNICATION – SAFETY feature operates in the following manner, in all OPERATING MODES – ON/ ON THERMO.

At all times and in all OPERATING MODES, the transmitter sends an RF signal every fteen (15) minutes, to the receiver, indicating that the transmitter is within the normal operating range of 20 feet. Should the receiver NOT receive a transmitter signal every 15 minutes, the IC software, in the RECEIVER, will begin a 2-HOUR (120-minute) countdown timing function. If during this 2-hour period, the receiver

does not receive a signal from the transmitter, the receiver will shut down the appliance being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps” for a period of 10 seconds. Then after 10 seconds of rapid beeping, the RECEIVER will continue

to emit a single “beep” every 4 seconds until a transmitter ON or MODE Button is pressed to reset the receiver. The intermittent 4-second

beeping will go on for as long as the receiver’s batteries last which could be in excess of one year.

To “reset” the RECEIVER and operate the appliance, you must press the ON or MODE button on the transmitter. By turning the system

to ON, the COMMUNICATION -SAFETY operation is overridden and the system will return to normal operation depending on the MODE selected at the transmitter. The COMMUNICATION – SAFETY feature will reactivate should the transmitter be taken out of the normal

operating range or should the transmitter’s batteries fail or be removed.

28743-0-0711 Page 35

Page 36

FRBTC REMOTE INSTRUCTIONS

THERMO- SAFETY FEATURE – RECEIVER (T/S –RX)

This ECS remote control has a THERMO- SAFETY feature that is built into the system’s RECEIVER. This feature is temperature- activated and provides an extra margin of safety when the RECEIVER is operating where ambient temperatures exceed 130°F degrees inside the receiver case.

The THERMO-SAFETY feature, in the RECEIVER, operates in the following manner, when the appliance is in operation.

The receiver is thermally protected from extreme heat conditions. Heat can have negative effect on the operation of the

receiver’s microprocessors.

For REMOTE RECEIVERS that operate on BATTERY POWER, these heat conditions can cause batteries to discharge

when temperatures exceed 115°F. Studies show that alkaline batteries, when exposed to a constant temperature of 115°F, can lose up to 50% of their operating power. When the battery cools down, it will partially recharge itself, but constant heating and cooling will reduce the battery’s normal life expectancy.

When the ambient temperature at the THERMISTOR, inside the receiver case, reaches 130°F, the THERMISTOR will auto- matically shut the appliance down and the RECEIVER will begin emitting a series of 2 “beeps”, every 4 seconds. When the ambient temperature, at the RECEIVER, drops between 120°F and 130°F, the user can reactivate the appliance by pushing the MODE button on the transmitter. The word ON must display on the LCD screen. When the MODE button is pressed to ON, the THERMISTOR “resets” itself and the replace will begin operating again. However, the “beeping” will continue, if the ambient temperature remains between 120°F and 130°F. This “beeping” alerts the user that the RECEIVER should be repositioned so the ambient temperature drops below 120°F.

When the temperature drops below 120°F, the “beeping” will cease, providing the user has “reset” the THERMISTOR by

pushing the MODE button to ON to operate the appliance, either manually or thermally. Allow sufcient time for the receiver to cool below 120°F, and then press MODE button to stop beeping.

MATCHING SECURITY CODES

Each transmitter can use one of 1,048,576 unique security codes. It may be necessary to program the remote receiver

to LEARN the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is

purchased from your dealer or the factory. When matching security codes, be sure slide button on the receiver is in the RE-

MOTE position; the code will NOT “LEARN” if the slide switch is in the OFF position. Program the remote receiver to LEARN a new security code by pushing in the LEARN button on the top of the remote receiver and then pressing any button on the transmitter. A change in the beeping pattern, at the receiver, indicates the transmitter’s code has been programmed into the

receiver. When an existing receiver is matched to a new transmitter, the new security code will overwrite the old one.

The microprocessor that controls the security code matching procedure is controlled by a timing function. If you are unsuccessful in matching the security code on the rst attempt, wait 1 - 2 minutes before trying again--this delay allows the microprocessor to reset its timer circuitry--and try up to two or three more times.

TRANSMITTER WALL CLIP

The transmitter can be hung on a wall using the clip provided. If the clip is installed

on a solid wood wall, drill 1/8” pilot holes and install with the screws provided. If it is installed on a plaster/wallboard wall, rst drill two 1/4” holes into the wall. Then use a hammer to tap in the two plastic wall anchors ush with the wall; then install the

screws provided.

28743-0-0711Page 36

Page 37

FRBTC REMOTE INSTRUCTIONS

BATTERY LIFE

Life expectancy of the alkaline batteries in the transmitter should be at least 12 months. Check and replace all batteries annually. When the transmitter no longer operates the remote receiver from a distance it did previously (i.e., the transmitter’s range has decreased) or the remote receiver doe not function at all, the batteries should be checked. It is important that the remote receiver batteries are fully charged and provides continuous output voltage of a least 5.3 volts. The length of the wire between the remote receiver and gas valve directly affects the operating performance of the remote system. The longer the wire, the more battery power is required to deliver signals between the remote receiver and the gas valve. Recommended length is no longer than 20 feet. The transmitter should operate with as little as 5.0 volts battery power.

TROUBLE SHOOTING

If you encounter problems with your replace system, the problem may be with the replace itself or it could be with the ECS remote. Review the replace manufacturer’s operation manual to make sure all connections are properly made. Then check the operation of the ECS remote in the following manner:

• Make sure the batteries are correctly installed in the RECEIVER. One reversed battery will keep receiver from operating

properly.

• Check battery in Transmitter to make sure contacts are touching (+) and (-) ends of battery. Bend metal contacts in for tighter t.

• Be sure RECEIVER and Transmitter are within 20’-25’ operating range.

• Keep RECEIVER from temperatures exceeding 130° F. Battery life shortened when ambient temperatures are above

130° F.

• If RECEIVER is installed in tightly enclosed metal surround, the operating distance will be shortened.

RECEIVER ADJUSTMENT – RECOMMENDED ADJUSTMENT

NOTE: The slide button, White or Black, covers the ADJ access hole

when installed.

A. To adjust at the receiver, use a small slotted screwdriver. Turn the adjust-

ment screw counter-clockwise about 5 degrees or a maximum of 1/8 turn.

This should correct the distance problem.

B. If that does not correct the problem, return adjustment screw to original

position and then turn adjustment screw clockwise.

This adjustment is like tuning your radio. If you keep turning the adjustment

screw, in either direction, you will go past the proper setting (tuning).

SPECIFICATIONS

BATTERIES: Transmitter 12V (A23) Remote Receiver 6V - 4ea. AA1.5 Alkaline FCC ID No.’s: transmitter - K9L1002TX; receiver - K9L3001RX Operating Frequency: 303.875MHZ Canadian ISC ID No.’s: transmitter - 2439 102 728; receiver - 2439 102 728A

28743-0-0711 Page 37

Page 38

AUTOMATIC HUMIDIFIER OPERATION

The Mantis Power-Vent High-Efciency Fireplace has an automatic humidier designed into the heater. As the heater operates,

condensate is created and is collected in a tank inside the heater. The condensate pump will take the condensate that is collected and pump it to a stainless steel tray where it evaporates into the

airstream. Humidity is then restored into the space.

Note: When the automatic humidier is engaged and is transfer- ring the condensate, there may be a noticeable hissing sound. This is normal, and the sound should persist for less than 30 seconds.

The amount of condensate created will vary based on several factors including but not limited to location of heater, air temperature,

length of venting, and whether the vent pipe is horizontal or vertical. The humidier will operate intermittently while the heater is

operating.

While the condensate pump is transferring the condensate from

the tank to the tray, the humidier L.E.D. light will ash during pump operation. See Page 31, Figure 57. Once the condensate is trans-

ferred, the light will turn off.

Figure 58

28743-0-0711Page 38

Page 39

FRONT BURNER SWITCH

REAR BURNER SWITCH

ECONOMY DISPLAY BUTTON

= OFF =ON

REMOTE

CONTROL

RECEIVER

14 WAY RIBBON TO CONTROL MODULE

BLUE

TRANSFORMER

RED

BLACK

OPTIONAL CONTROLS

Economy Mode (Red Button Operation)

To utilize this feature, a programmable control or thermostat must be connected to the heater. A red button is located next to the

burner switches on the front control panel. See Figure 59. This is called the economy mode.

Figure 59

To use this feature, both burner switches need to be in the “ON”

position, and the red button must be pressed so it is illuminated. This will ignite the front burner. The front burner will remain on when the red button is illuminated, and the back burner will cycle with the thermostat. The red button acts only as an override for the front burner.

To Deactivate

Press the red button so it is not illuminated, then the heater will return to normal operation.

Battery Operated Controls

This unit is equipped with a factory installed wireless remote.

All Remote Controls are all battery operated devices.

Optional Battery Operated Control

FRBTP Battery Operated Remote with Programmable Ther-

mostat

TRW Battery Operated Wireless Remote Wall Thermostat

These optional controls will work with the factory installed receiver.

CAUTION

Before connecting any controller, disconnect power to the appliance.

Figure 60

Adjust the remote from the instructions provided with the remote

control.

Note: If the heater will not be used for long periods of time, turn the burner switches to the “OFF” position and turn the power off at the power source.

28743-0-0711 Page 39

Page 40

MAINTENANCE & SERVICE

The Mantis should be inspected and serviced annually by a quali-

ed service person. This will ensure that the appliance is operating safely and efciently. Should you suspect any abnormal opera-

tion, contact a service person that has been trained to service this product.

Cleaning the Glass Door

After the initial paint curing, a slight lm may form on the glass. It is recommended to clean the glass with gas replace glass cleaner.

The glass will need to be cleaned periodically during the year. Use care when removing and cleaning the glass. In the event the glass needs replaced, contact a qualied service person. Only glass approved by Empire Comfort Systems Inc. may be used, any substitute glasses will void the warranty.

CAUTION

Do not attempt to clean the glass when it is hot. Do not strike or hit the glass.

WARNING

Do not operate this appliance without the glass door in place. Do not operate if the glass front is broken or damaged. Do not use the glass door if the gasket is missing or is damaged.

Resetting the Heater

To reset the heater, rst turn both burner switches to the OFF position. Verify the red button next to the burners is not illuminated. If

a Remote Control is tted, turn the remote to the “OFF” position.

Turn the power off at the power source for 5 minutes.

Turn the power back on, and verify the L.E.D. lights on the Control Panel Circuit Plate are illuminated. The burners should ignite in approximately 60 seconds. The circulating blower will start in 3 to 5 minutes. The blower may continue to operate after the burners are turned off.

WARNING

Potential risk of re, electric shock, and personal injury.

Take precautions to reduce such risks

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

If equipped, the Mantis can also be reset by switching the main

power switch to the “OFF” position for 5 minutes. See Figure 61.

CAUTION

Be certain the glass is cool before handling.

BAY WINDOW MANTIS MODELS Removing the Glass Door

1. Remove the top of the cabinet.

2. Open the panels on the left and right sides. The panels pivot

in place.

3. Release the two door latches on both the left and right sides

of the rebox.

4. Carefully grab the glass frame and pull towards you. Do not damage or remove the gasket from the door.

FIREPLACE MANTIS MODELS Removing the Glass Door

1. Remove the lower louvered panel by lifting up then pulling out.

2. Release the two hinge clips on underside of rebox.

3. Angle the bottom of glass assembly approximately 60 degrees out from rebox. Gently pull glass assembly away from rebox. Do not damage or remove the gasket from the door.

Figure 61

28743-0-0711Page 40

Page 41

MAINTENANCE & SERVICE

Over Temperature Limit Switch

The Mantis Power-Vent High-Efciency Fireplace is protected

against overheating with a high temperature switch, which protects the heat exchanger, plastic sump and inducer.

If the over temperature limit activates, the gas supply will shut off

and both the inducer and circulating air blower will run. Once the

heater cools down, the limit will reset and the heater will operate normally.

Circulating Air Blower

The circulating air blower should be checked and cleaned annu-

ally by a qualied service person to ensure that your appliance is operating efciently. Any dirt or lint can affect the operation of the

blower.

RECOMMENDED MAINTENANCE

MAINTENANCE ITEM

Verify the area is free from combustible materials. X X

Verify the combustion and ventilation air is not restricted. X

Verify the ue and inlet pipes do not have any cracks or holes. X

Verify burner ame. X

Clean the blower compartment X

Clean the burners. X

Verify the condensate system is clean and leak free. X

Heat Exchanger

The heat exchanger is located on the backside of the heater. The heat exchanger should be inspected and cleaned annually by a

qualied service person.

Replacement Logs

If for any reason a log should need replacement, contact your Mantis dealer for correct replacement logs. Replacement logs must be installed and positioned as outlined on Pages 25 to 26.

CAUTION

Proper positioning of the logs is critical to the safe and clean operation of this heater. Sooting and other problems

may result if the logs are not properly and rmly positioned

in the appliance.

FREQUENCY OF MAINTENANCE

MONTHLY

BY HOMEOWNER

ANNUALLY

BY SERVICE PERSON

If service is needed to the condensate pump, the wires must be attached in the same order they were removed. If the pump is replaced, follow the wire connection instruction label on the pump cover.

Figure 62

28743-0-0711 Page 41

Page 42

BAY WINDOW MANTIS PARTS LIST

WARNING

Use only manufacturer’s replacement parts. Use of any other parts could cause injury or death.

INDEX

NO.

1 27072 REAR PANEL ASSEMBLY

2 21654 BRACKET, PIPE ASSEMBLY

3 24831 REAR HEAT SHIELD ASSEMBLY

4A 21664

4B 22933 SLIM TOP ASSEMBLY

4C 22934 SHORT TOP ASSEMBLY

5 R8854 BALL STUD

6 22693 TOP HEAT SHIELD ASSEMBLY

7 21637 FIREBOX ASSEMBLY

8 26089

9 R10337 GASKET, END PLATE

10 R9987 FLEX LINE - 24”

11 26087

12 22863

13 R10299 SWITCH, BIMETALIC

14 R8795 GASKET, SUMP

15 26090 FIN TUBE ASSEMBLY

16 R8811 GASKET, INLET HEADER

17 R10966 TUBING (SUMP TO PUMP)

18 21652

19 21627 SHIELD, REAR INNER

20 25227 ELECTRIC PARTS PLACE

21 21667 LEFT SIDE DOOR ASSEMBLY

22 22642 TUBE, CONDENSATE

23 21647

24 21605 COVER, INLET AIR DUCT

25 22780 INLET AIR DUCT ASSEMBLY

26 R10491 GASKET, INLET AIR DUCT

PART

NO.

DESCRIPTION

TOP COVER ASSEMBLY (INCLUDES #5)

HEAT EXCHANGER TUBE ASSEMBLY

SUMP ASSEMBLY

(INCLUDES #12 & #14)

BLOWER ASSEMBLY

(INCLUDES #14)

TUBING (SUMP TO PRESSURE SWITCH)

CONNECTOR TUBING ASSEMBLY (PUMP TO CONDENSATE TUBE)

INDEX

NO.

27 21641

28 R4053 CLAMP, DOOR (4 USED ON UNIT)

29 22773 THERMISTER ASSEMBLY

30 R10488 3/8 ELBOW, 90

32 26789 BOTTOM PAN ASSEMBLY

33 26123 INLET HEADER

34 21665 RIGHT SIDE DOOR ASSEMBLY

35 21651

36 R8835 FITTING, BARBED HOSE

37 22865

38 21611 BRACKET, IGNITOR

39 R8807 FLAME SENSOR

40 26800 LOG PLATE ASSEMBLY

41 26787

41 22753

42 26801

42 22658

43 R9831

44 R8790 BUSHING, BURNER

45 P208 REAR ORIFICE, LPG

45 P288 REAR ORIFICE, NAT

46 P208 FRONT ORIFICE, NAT

46 P307 FRONT ORIFICE, LPG

47 R10796 HOLDER, ORIFICE

48 R7572 JAMB NUT

49 27071 GAS LINE - REAR

PART

NO.

DESCRIPTION

BRACKET ASSEMBLY THERMISTER

(SPRING CLIP INCLUDED)

TUBING (FIREBOX TO PRESSURE SWITCH)

IGNITOR, HOT SURFACE ASSEMBLY

SMALL BURNER ASSEMBLY LP (INCLUDES R10675 AND #44)

SMALL BURNER ASSEMBLY NAT (INCLUDES #43 AND #44)

LARGE BURNER ASSEMBLY - LP (INCLUDES #44 AND R10676)

LARGE BURNER ASSEMBLY - NAT (INCLUDES #44 AND R10675)

BUSHING, AIR SHUTTER (NAT ONLY)

28743-0-0711Page 42

Page 43

BAY WINDOW MANTIS PARTS LIST

WARNING

Use only manufacturer’s replacement parts. Use of any other parts could cause injury or death.

INDEX

NO.

50 26128 GAS LINE - FRONT

51 M174 GASKET

52 11269 GAS LINE BRACKET

53 R8886 COMPRESSION FITTING

54 R8812 VALVE, NAT

54 R8869 VALVE, LPG

55 R8898 PIPE NIPPLE

56 R8825 SOLENOID

57 R3312 CONNECTOR, MALE 3/8 X 3/8

59 R10072 SHUT-OFF VALVE

60 21643 FIREBOX BASE ASSEMBLY

61 R10775 CONTROL BOX ASSEMBLY

62 R8889 TRANSFORMER 12-24V

63 R8804 TRANSFORMER 24V

64 25325 CONDENSATE PUMP COVER

67 27004 CIRCULATING BLOWER ASSEMBLY

68 21663 DOOR ASSEMBLY, BLACK

68 22758 DOOR ASSEMBLY, CHROME

68 22759 DOOR ASSEMBLY, GOLD

69 26582 FRONT PANEL ASSEMBLY

70 R8840

71 R8809 SWITCH, DOUBLE ROCKER

72 R8904 CIRCUIT BOARD

73 25226 CIRCUIT BOARD PLATE

74 R10759 RIBBON CABLE

75 R11043 CIRCUIT BOARD WIRE HARNESS

76 R10182 WIRE HARNESS, 120V

77 R10183 WIRE HARNESS 12V

78 R10190 WIRE HARNESS 12V

79 26075 PUMP ASSEMBLY

PART

NO.

DESCRIPTION

WIRE HARNESS ASSEMBLY WITH ECONOMY SWITCH

INDEX

NO.

80 R10489 AIR PRESSURE SWITCH

81 R8881 CAPACITOR 3uF

82 R8880 CAPACITOR 4uF

84 R10485 LOG, LEFT REAR

85 R8822 LOG, TOP LEFT

86 R10487 LOG, TOP RIGHT

87 R10486 LOG, RIGHT

88 R8820 LOG, CENTER

89 R8819 LOG, FRONT LEFT

90 R8821 LOG, FRONT RIGHT

91 R2522 MAIN POWER SWITCH

92 R10610

93 26119 HEADER COVER - OUTLET

94 26123 HEADER COVER - INLET

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

PART

NO.

WIRE HARNESS, MAIN POWER SWITCH

R10675 BUSHING, AIR SHUTTER

R10676 BUSHING, AIR SHUTTER

FRBTC THERMOSTAT

DESCRIPTION

28743-0-0711 Page 43

Page 44

BAY WINDOW MANTIS PARTS VIEW

28743-0-0711Page 44

Page 45

BAY WINDOW MANTIS PARTS VIEW

28743-0-0711 Page 45

Page 46

FIREPLACE MANTIS PARTS LIST

WARNING

Use only manufacturer’s replacement parts. Use of any other parts could cause injury or death.

INDEX

NO.

1 25207 PANEL - TOP

2 21595 CONDENSATE TRAY

3 25223 LOUVER - TOP

4 25212 REAR BURNER TRAY

5 R9987 FLEX LINE

6 26081

7 25205 PANEL - LEFT SIDE

8 21605 INLET AIR DUCT COVER

9 21604 INLET AIR DUCT

10 R10491 INLET AIR DUCT GASKET

11 R8825 SOLENOID

12 R10072 GAS SHUT OFF VALVE

13 R8812 VALVE - NAT

14 26071 GLASS ASSEMBLY

15 25208 BOTTOM PAN

16 27004 CIRCULATING BLOWER ASSEMBLY

18 R10338 PRESSURE SWITCH

19 25227 ELECTRICAL PARTS PLATE

20 R10775 CONTROL BOX

21 R8889 TRANSFORMER 12-24V

22 R8881 CAPACITOR 3uF

23 R8880 CAPACITOR 4uF

24 R8804 TRANSFORMER - 24V

25 26075 PUMP ASSEMBLY

28 25226 CIRCUIT BOARD PLATE

29 R8809 DOUBLE ROCKER SWITCH

PART

NO.

DESCRIPTION

FRONT BURNER TRAY ASSEMBLY

INDEX

NO.

30 R8840

31 R8904 CIRCUIT BOARD

32 26083 FRONT BURNER ASSEMBLY

33 26082 BACK BURNER ASSEMBLY

34 R11012 ORIFICE HOLDER

35 22865

36 R10967

37 25210 AIR DUCT CHANNEL

38 25214 PANEL - RIGHT SIDE

39 25221 FIREBOX BASE

40 25222

41 R4053

42 25225

43 25215 BAFFLE

44 26080 FIREBOX ASSEMBLY

45 26087 SUMP ASSEMBLY

46 R8799 INDUCER ASSEMBLY

47 26089 FLEX PIPE ASSEMBLY

48 26090 FIN TUBE ASSEMBLY

49 R8811 INLET HEADER GASKET

50 25204 PANEL - BACK

51 R10796 ORIFICE HOLDER

PART

NO.

DESCRIPTION

WIRE HARNESS ASSEMBLY WITH ECONOMY SWITCH

HOT SURFACE IGNITOR (2 REQUIRED)

FLAME SENSOR (2 REQUIRED)

DOOR BRACKET (2 REQUIRED)

DOOR CLAMP (2 REQUIRED)

LATCH BRACKET (2 REQUIRED)

28743-0-0711Page 46

Page 47

FIREPLACE MANTIS PARTS LIST

WARNING

Use only manufacturer’s replacement parts. Use of any other parts could cause injury or death.

INDEX

NO.

52 R10182 WIRE HARNESS - 120V

53 R10190 WIRE HARNESS - 12V SMALL

54 R10183 WIRE HARNESS - 12V LARGE

55 R8814 THERMISTER

57 R8872 WIRE HARNESS

58 R10759 RIBBON CABLE

59 24831

60 22642 CONDENSATE PUMP TUBE

61 25325 CONDENSATE PUMP COVER

62 R10376 REAR LOG

63 R10381 LEFT LOG

64 R10380 RIGHT LOG

65 R10379 MIDDLE LOG

66 R10378 FRONT LEFT LOG

67 R10377 FRONT RIGHT LOG

68 R10383 LEFT TOP LOG

69 R10382 RIGHT TOP LOG

70 25216

71 R2522 MAIN POWER SWITCH

73 R10610

74 R8795 GASKET - SUMP

75 26119 HEADER COVER - OUTLET

76 26123 HEADER COVER - INLET

PART

NO.

R10077 LOG SET (INCLUDES 62 - 69)

DESCRIPTION

REAR HEAT SHIELD ASSEMBLY

BRACKET, STANDOFF (2 REQUIRED)

WIRE HARNESS, MAIN POWER SWITCH

INDEX

NO.

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

NOT

SHOWN

PART

NO.

R10093 ORIFICE #47 - NAT

R10094 ORIFICE #49 - NAT

R10095 ORIFICE #1.2MM - LP

R10096 ORIFICE #55 - LP

26117

R10299 SWITCH, BIMETALIC

FRBTC THERMOSTAT

R10966 TUBING (SUMP TO PUMP)

DESCRIPTION

AIR DUCT CHANNEL COVER PLATE

- NAT ONLY

28743-0-0711 Page 47

Page 48

FIREPLACE MANTIS PARTS VIEW

28743-0-0711Page 48

Page 49

MASTER PARTS DISTRIBUTOR LIST

To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.

com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit.

To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.

This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort. com.

Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.

Dey Distributing

1401 Willow Lake Boulevard

Vadnais Heights, MN 55101

Phone: 651-490-9191 Toll Free: 800-397-1339 Website: www.deydistributing.com Parts: Heater & Hearth

Victor Division of F. W. Webb Company

200 Locust Street

Hartford, CT 06114

Phone: 860-722-2433 Toll Free: 800-243-9360 Fax: 860-293-0479 Toll Free Fax: 800-274-2004 Websites: www.fwwebb.com & www.victormfg.com Parts: Heater & Hearth and Grills

HOW TO ORDER REPAIR PARTS

East Coast Energy Products

10 East Route 36 West Long Branch, NJ 07764

Phone: 732-870-8809 Toll Free: 800-755-8809 Fax: 732-870-8811 Website: www.eastcoastenergy.com Parts: Heater & Hearth and Grills

Parts Not Under Warranty

Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distributors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the

service person/dealer.

Warranty Parts

Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for warranty parts.

All parts listed in the Parts List have a Part Number. When ordering parts, rst obtain the Model Number and Serial Number from the

name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following illustration and part list. Be sure to give all this information . . .

Appliance Model Number Part Description

Appliance Serial Number Part Number

Type of Gas (Propane or Natural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipments contingent upon strikes, res and all causes beyond our control.

28743-0-0711 Page 49

Page 50

WARRANTY TERMS

Purchase Date:

Dealer Name/Phone:

Installer - Place Serial Number

Empire Comfort Systems Inc. warrants this hearth product to be free from

defects at the time of manufacture and for the periods specied below. Hearth products must be installed by a qualied technician and must be

maintained and operated safely, in accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is

not transferable. All warranty repairs must be accomplished by a qualied gas appliance technician.

Limited Ten-Year Heat Exchanger Warranty

Empire promises to the owner that if the heat exchanger (see parts list) fails because of defective workmanship or material within ten years from the date of purchase, Empire will repair, or at Empire’s option, replace the defective heat exchanger.

Sticker Here and Leave this

Manual with the Consumer.

Limited Five-Year Parts Warranty

Should any part fail because of defective workmanship or material within ve years from the date of purchase, Empire will

repair or replace it, at Empire’s option.

Limited Two-Year Labor Warranty

Within two years from the date of purchase, Empire will pay reasonable labor to have that defect repaired or replaced at

Empire’s option. All labor must be accomplished by a qualied gas appliance technician.

Duties Of The Owner

The appliance must be installed by a qualied installer and operated in accordance with the written instructions furnished

with the appliance. Ready access to the appliance for service is the responsibility of the owner. Travel, diagnostic costs and freight charges on warranted parts to and from the factory is the responsibility of the owner.

A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty period.

What Is Not Covered

This warranty does not cover damages that might result from the use, misuse, or improper installation of this appliance. This warranty does not cover claims that do not involve defective workmanship or materials.

This warranty does not cover unauthorized service or parts replacements will not be covered.

How To Get Service

To make a claim under this warranty, please have your receipt available and contact your installing dealer. Provide the

dealer with the model number, serial number, type of gas and purchase verication. The installing dealer is responsible for

providing service and will contact the factory to initiate any warranted parts replacements. Empire will make replacement parts available at the factory. Shipping expenses are not covered.

If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department, Empire Comfort Systems Inc., P.O. Box 529, Belleville, Illinois 62222, or send an e-mail to info@empirecomfort.com with “Consumer Relations” in the subject line.

Your Rights Under State Law

This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state.

28743-0-0711Page 50

Page 51

APPLIANCE SERVICE HISTORY

Date Dealer Name Service Technician Name Service Performed/Notes

28743-0-0711 Page 51

Page 52

EMPIRE

Comfor t Systems

Empire Comfort Systems Inc.

918 Freeburg Ave. Belleville, IL 62220

If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer.

www.empirecomfort.com

28743-0-0711Page 52

Empire Comfort Systems BI28GP-5, BF28GP-5, BI28BM-5, BI28CN-5, BP28BM-5 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual