INSTALLATION INSTRUCTIONS
AND
OWNER'S MANUAL
CAST IRON
DIRECT VENT FIREPLACE
MODEL
CIDV-30-7
EFFECTIVE DATE
AUGUST, 2000
WARNING: If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
FOR YOUR SAFETY: What to do if you smell
gas:
• Do not touch any electrical switches
• Do not try to light any appliance.
• Do not use the phone in your building.
• Immediately call your gas supplier from a
neighbor's phone.
• Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call
the fire department.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause
injury or property damage. Refer to this manual.
For assistance or additional information consult
a qualified installer, service agency, or the gas
supplier.
AVERTISSEMENT: Quiconque ne respecte pas à
la lettre les instructions dans le présent manuel
risque de déclencher un incendie ou une explosion
entraíant des dommages matériels, des lésions
corporelles ou la perte de vies humaines.
POUR VOTRE SÉCURITÉ: Que faire si vous
sentez une odeur de gaz:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous
servir des téléphones se trouvant dans le
bâtiment où vous vous trouvez.
• Évacuez la pièce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service dos incendies.
AVERTISSEMENT: Une installation, un réglage,
une modification, un entretien ou une maintenance
incorrects peuvent entraîner des dommages
matériels, des lésions corporelles ou la perte de vies
humaines. Consulter le manuel des usagers fourn
avec ce générateur d'air chaud.
Page 1R-5086
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card
supplied with appliance.
3. Installer should show owner how to start and operate appliance
and thermostat.
WARNING: Any change to this appliance or its control can
be dangerous. This is a heating appliance and any panel,
door or guard removed for servicing an appliance must be
replaced prior to operating the appliance.
General Information
This appliance is design certified in accordance with American National
Standard/CSA Standard ANSI Z21.88-1998/CSA 2.33-M98 by the
American Gas Association and Canadian Gas Association as a Direct
Vent Fireplace and should be installed according to these instructions.
The efficiency rating of this appliance is a product thermal efficiency
rating determined under continuous operating conditions and was
determined independently of any installed system.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not shown on
the rating plate is the responsibility of the person and company
making the change.
Notice During initial firing of this unit, its paint will bake out and
smoke will occur. To prevent triggering of smoke alarms, ventilate
the room in which the unit is installed.
WARNING: Do not operate appliance with the glass front
removed, cracked or broken. Replacement of the glass should
be done by a licensed or qualified service person.
WARNING: If not installed, operated and maintained in
accordance with the manufacturer's instructions, this product
could expose you to substances in fuel or from fuel combustion
which can cause death or serious illness.
Appliance must not be connected to a chimney flue that is servicing a
separate solid-fuel burning appliance.
Attention: All vent runs must have a minimum VERTICAL rise of
two feet. If the vent run is directly behind the appliance, you must
attach Simpson Dura-Vent 36" snorkel, part number SD-981 on the
exterior of the building. See Venting Requirements, page 11.
Specifications
Model CIDV-30
Input BTU/HR (KW/H) Max (LP/NAT) 30,000 (8.7)
BTU/HR (KW/H) Min. LP 22,000 (6.4)
BTU/HR (KW/H) Min. Nat. 19,500 (5.7)
Height 27 3/4" (70.5cm)
Width 25 1/2" (64.8cm)
Depth 23" (58.4cm)
Gas Inlet (Pipe) 1/2" (13mm)
Floor to top of collar on vertical 27 5/8" (70.2cm)
position of Vent Elbow
Floor to center of collar on horizontal 24 3/32" (61.2cm)
position of Vent Elbow
Floor to Center of 90° elbow with a 55 1/2" (141cm)
24" length of pipe (see Figure 5)
Stove Casting (Must be ordered with Firebox.)
CIFB-1 Flat Black
CIPB-1 Porcelain Black
CIPG-1 Porcelain Green
CIPS-1 Porcelain Sand
CIPN-1 Porcelain Navy
CIPR-1 Porcelain Red
Accessories
GWSG-T 750 Millivolt Wall Thermostat
DVKH-1 Direct Vent Kit for Horizontal Run
(Includes DVKA-1 Adapter)
DVKV-1 Direct Vent Kit for Vertical Run
(Includes DVKA-1 Adapter)
DVKA-1 Direct Vent Kit Adapter
FRBC-1 Battery Operated Remote Control
FRBTC-1 Battery Operated Remote Control w/Thermostat
FREC-1 Electric Remote Control
FWS-1 Wall Switch
CIB-2 Automatic Blower
Stone Inlay Replaces Standard Grille Top
CII-2 Stone Inlay Empress Green
CII-3 Stone Inlay Hunan Jade
CII-4 Stone Inlay Gray Botticino
CII-5 Stone Inlay Azul
CII-6 Stone Inlay Salome
CII-7 Stone Inlay Black Swan
THIS IS A HEATING APPLIANCE
• Due to high temperatures the appliance should be located out
of traffic and away from furniture and draperies.
• Children and adults should be alerted to the hazards of high
surface temperatures and should stay away to avoid burns or
clothing ignition.
• Young children should be carefully supervised when they are
in the same room as the appliance.
• Clothing or other flammable material should not be placed on
or near the appliance.
• Surveiller les enfants. Garder les vêtements, les meubles, l'essence
ou autres liquides à vapeur inflammables lin de l'appareil.
• Any safety screen or guard removed for servicing an appliance
must be replaced prior to operating the appliance.
• The glass front or any part removed for servicing the appliance
must be replaced prior to operating the appliance. Work should
be done by a qualified service person
• Keep burner and control compartment clean.
• Vent cap hot while furnace is in operation.
• Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected before use and at least annually by a qualified service person.
More frequent cleaning may be required due to excessive lint
from carpeting, bedding materials, etc. It is imperative that
control compartments, burners and circulating air passageways of the appliance be kept clean.
Page 2 R-5086
• S'assurer que le brûleur et le compartiment des commandes sont
propres. Voir les instructions d'installation et d'utilisation qui
accompagnent l'appareil.
• DO NOT put anything around the furnace that will obstruct
the flow of combustion and ventilation air.
• DO keep the appliance area clear and free from combustible
material, gasoline and other flammable vapors and liquids.
• DO examine venting system periodically and replace damaged parts.
• CAUTION: The glass used in your heater is a special high
temperature ceramic glass. If the glass is cracked or damaged in
any way, it should be replaced only with a complete glass frame
assembly from Empire. See parts list on Page 26 for ordering.
• DO make a periodic visual check of pilot and burner. Clean
and replace damaged parts.
• DO NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
• Ne pas se servir de cet appareil s'il a été plongé dans l'eau,
complètement ou en partie. Appeler un technicien qualifié pour
inspecter l'appareil et remplacer toute partie du système de
contrôle et toute commande qui ont été plongés dans l'eau.
• Under no circumstances should any solid fuels (wood, coal, paper
or cardboard, etc.) be used in this appliance.
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions which can protect both you and your family from an
accident. Read them carefully now, then review them point
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
by point with the members of your household. Someday
when there may not be a minute to lose, everyone's safety will
depend on knowing exactly what to do. If, after reading the
following information, you feel you still need more information, please contact your gas supplier.
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell
the odor of the chemical stench put into the gas. You must
find out if you can smell the odorant in propane. Smoking can
decrease your ability to smell. Being around an odor for a time
can affect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not
smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under
some circumstances. For example, if there is an underground
leak, the movement of the gas through soil can filter the odorant.
Odorants in LP-Gas also are subject to oxidation. This fading
firefighters declare them to be safe.
• Use your neighbor's phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and firefighters check for
escaped gas. Have them air out the area before you return.
Properly trained LP-Gas service people should repair the
leak, then check and relight the gas appliance for you.
can occur if there is rust inside the storage tank or in iron gas
pipes.
The odorant in escaped gas can adsorb or absorb onto or into
walls, masonry and other materials and fabrics in a room. That
will take some of the odorant out of the gas, reducing its odor
intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest
gas odor. If you detect any odor, treat it as a serious leak.
Immediately go into action as instructed earlier.
SOME POINTS TO REMEMBER
• Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-Gas has a weak or abnormal odor, call your LPGas Dealer.
• If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-Gas
system. If you are qualified, consciously think about the odor
of LP-Gas prior to and while lighting pilot lights or performing service or making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
to set too long before refilling. Cylinders and tanks which
have been out of service for a time may develop internal rust
which will cause odor fade. If such conditions are suspected
to exist, a periodic sniff test of the gas is advisable. If you
have any question about the gas odor, call your LP-gas
dealer. A periodic sniff test of the LP-gas is a good safety
measure under any condition.
• If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the
same immediate action recommended above for the occasion
when you do detect the odorized LP-Gas.
• If you experience a complete "gas out," (the container is
under no vapor pressure), turn the tank valve off immediately. If the container valve is left on, the container may draw
in some air through openings such as pilot light orifices. If
this occurs, some new internal rusting could occur. If the
valve is left open, then treat the container as a new tank.
Always be sure your container is under vapor pressure by
turning it off at the container before it goes completely empty
or having it refilled before it is completely empty.
Page 3R-5086
Installation in Residential Garages
Gas utilization equipment in residential garages shall be installed so that
all burners and burner ignition devices are located not less than 18"
(457mm) above the floor.
Such equipment shall be located, or protected, so it is not subject to
physical damage by a moving vehicle.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or
accessories and repair and servicing of equipment shall be performed only
by a qualified agency. The term "qualified agency" means any individual,
firm, corporation or company which either in person or through a
representative is engaged in and is responsible for (a) the installation or
replacement of gas piping or (b) the connection, installation, repair or
servicing of equipment, who is experienced in such work, familiar with
all precautions required and has complied with all the requirements of the
authority having jurisdiction.
The installation must conform with local codes, or, in the absence of local
codes, with the National Fuel Gas Code, ANSI Z223.1*/Canadian
Installation Code, CAN/CGA B149.
*Available from the American National Standards Institute, Inc., 11 West 42nd St., New York,
NY 10036.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence
de tels règlements, selon les Codes d'installation CAN/CGA-B149.
Introduction
This model is a direct vent gas appliance and is designed to operate with
all combustion air being siphoned from the outside of the building and all
exhaust gases expelled to the outside of the building.
Warning: This unit is not for use with solid fuel.
Pre-Installation Preparation
This direct vent gas fireplace and its components are tested and safe when
installed in accordance with this Installation Manual. Report to your
dealer any parts damaged in shipment, specifically check glass condition.
Do not install unit with damaged, incomplete, or substitute parts. Read all
instructions before starting installation and follow these instructions
carefully during installation to insure maximum benefit and safety.
Failure to follow them will void your warranty and may present a fire
hazard.
The Empire Comfort System, Inc. warranty will be voided by, and Empire
Comfort System, Inc. disclaims any responsibility for the following
actions:
• Installation of any damaged fireplace or vent system component.
• Modification of the fireplace or direct vent system.
• Installation other than as instructed by Empire Comfort System, Inc.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not manufactured or
approved by Empire Comfort System, Inc.
High Altitude Installation
When installing this unit at an elevation above 2000 feet (in the United
States) it may be necessary to decrease the input rating by changing the
existing burner orifice to a smaller size. Generally, input should be
reduced 4 percent for each 1000 feet above sea level. However, if the
heating value of the gas has been reduced, this general rule may not apply.
Check with local gas utility for proper orifice size identification.
APPLIES TO CANADIAN MODELS ONLY
Altitude: 0-4,500 feet (0-1370 m) without orifice change.
For high altitude installations consult the local gas distributor or the
authority having jurisdiction for proper rating methods. If the installer
must convert the unit to adjust for varying altitudes, the information
sticker (illustrated below) must be filled out by the installer and adhered
to the appliance at the time of conversion.
THE CONVERSION SHALL BE CARRIED OUT BY A
MANUFACTURER'S AUTHORIZED REPRESENTATIVE IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFAC-
Page 4 R-5086
TURER, PROVINCIAL OR TERRITORIAL AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN/CGA-B141.1 OR CAN/CGA-B141.2 INSTALLATION CODES.
LA CONVERSION DOIT ÊTRE EFFECTUÉE CONFORMÉMENT
AUX RÉGLEMENTATION PROVINCIAUX EN CAUSE ET AUX
EXIGENCES DES CODES D'INSTALLATION CAN/CGA-B149.
This appliance has been converted for use at an altitude of
Orifice size Manifold Pressure
Input (Btu/h) Fuel Type
Date of Conversion Converted by
Cet appareil a été converti au
Injecteur Pression à la tubulure d'alimentation
Déoit calorifique
Gas Supply (Figure 1)
Check all local codes for requirements, especially for the size and type of
gas supply line required.
Recommended Gas Pipe Diameter
Pipe Length Schedule 40 Pipe Tubing, Type L
(Feet) Inside Diameter Outside Diameter
Nat. L.P. Nat. L.P.
0-10 1/2" 3/8" 1/2" 3/8"
1.3 cm 1.0 cm 1.3 cm 1.0 cm
10-40 1/2" 1/2" 5/8" 1/2"
1.3 cm 1.3 cm 1.6 cm 1.3 cm
40-100 1/2" 1/2" 3/4" 1/2"
1.3 cm 1.3 cm 1.9 cm 1.3 cm
100-150 3/4" 1/2" 7/8" 3/4"
1.9 cm 1.3 cm 2.2 cm 1.9 cm
Note: Never use plastic pipe. Check to confirm whether your local codes
allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is always
best to consult your local authority and installation code.
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority having
jurisdiction.
Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/CGAB149 (.1 or .2) installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate, contact
your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant to the
action of liquefied petroleum gases. The gas lines must be checked for
leaks by the installer. This should be done with a soap solution watching
for bubbles on all exposed connections, and if unexposed, a pressure test
should be made.
Never use an exposed flame to check for leaks. Appliance must be
disconnected from piping at inlet of control valve and pipe capped or
plugged for pressure test. Never pressure test with appliance
connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas line
upstream of the gas control to aid in servicing. It is required by the
National Fuel Gas Code that a drip line be installed near the gas inlet. This
should consist of a vertical length of pipe tee connected into the gas line
that is capped on the bottom in which condensation and foreign particles
may collect.
Figure 1
Method of Installing a Tee Fitting Sediment Trap
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.
plugged tapping, accessible for test gauge connection, must be placed
immediately upstream of the gas supply connection to the appliance.
2. The appliance and its appliance main gas valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping system by
closing its equipment shutoff valve during any pressure testing of the
gas supply piping system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
Attention! If one of the procedures results in pressures in excess of 1/2
psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result in a
hazardous condition.
Checking Manifold Pressure
Both Propane and Natural gas valves have a built-in pressure regulator in
the gas valve. Natural gas models will have a manifold pressure of
approximately 3.5" w.c. (.871kPa) for maximum input or 1.7" w.c.
(.423kPa) for minimum input at the valve outlet with the inlet pressure to
the valve from a minimum of 5.0" w.c. (1.245kPa) for the purpose of input
adjustment to a maximum of 10.5" (2.615kPa) w.c. Propane gas models
will have a manifold pressure approximately 10.0"w.c. (2.49kPa) for
maximum input or 5.9" w.c. (1.469kPa) for minimum input at the valve
outlet with the inlet pressure to the valve from a minimum of 11.0" w.c.
(2.739kPa) for the purpose of input adjustment to a maximum of 13.0"
w.c. (3.237kPa).
A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge connection,
is located on the outlet side of the gas control.
Installation on Rugs and Tile
If this appliance is to be installed directly on carpeting, tile, or other
combustible material, other than wood flooring, the appliance shall be
installed on a metal or wood panel extending the full width and depth of
the appliance.
The base referred to above does not mean the fire-proof base as used on
wood stoves. The protection is primarily for rugs that may be extremely
thick and light-color tile that can discolor.
Clearances (Figures 2, 3, 4 and 5)
In selecting a location for installation, it is necessary to provide adequate
accessibility clearances for servicing and proper operation.
Locating and Venting the Direct Vent Fireplace
Clearances: When facing the front of the direct vent fireplace the
minimum clearances to combustible construction (material) are the
following:
Top of appliance (ceiling) 36 (inches)
Rear Wall 2 (inches)
Side Wall 6 (inches)
Heater Corners (45° angle) to Wall 4 (inches)
Floor 0 (inches)
Figure 2
Figure 3
Page 5R-5086
Appliance Hardware Package (Figure 6)
Figure 6
Appliance Hardware Package Parts List
Part Part Quantity
Description Number Supplied
1/4-20 x 1" Phillips Head Bolt R-3188 4
1/4-20 x 3/8" Phillips Head Bolt R-3646 16
1/4-20 x 1/2" Leveling Bolt R-3747 4
No. 10 x 1/2" R-2737 8
Hex Washer Head Screw
1/4-20 Washer Head Nut R-3185 4
Leg Pad "A" (see Figure 7) CI-008 2
Leg Pad "B" (see Figure 7) CI-009 2
1-1/4" x 1/2" Retaining Tab CI-007 4
(see Figure 10)
1/4 x 9/32 Washer (Not Shown) R-1150 8
Assembly of Cast Iron (Outer Casing) Stove Casting
(Figures 7, 8, 9, 10, 11 and 12)
Attention: Included in the hardware package are (8) 1/4" inside diam-
eter washers. A 1/4" washer may be used with a 1/4-20 x 3/8" bolt when
assembling the stove casting parts. If a bolt hole is not tapped deep
enough for a tight fit between stove casting parts, the 1/4" washer can
be used as a shim to provide a tight fit.
The 1/4" washers are not required for assembly of the stove casting if all
the bolt holes are tapped to a proper depth.
Additonal 1/4" washers are to be purchased locally.
1. Place porcelain casting pieces on a non-abrasive surface in order
Page 6 R-5086
Figure 7
to protect the porcelain finish. The exterior of the porcelain
casting pieces should be facing the non-abrasive surface.
2. The assembly of the casting is accomplished in 6 stages:
A. Attaching legs to the sides (Figure 7).
B. Attaching rear cover to sides (Figure 8).
C. Removing protective packaging from casing front and window
(Figure 9).
D. Assembly of front by attaching retaining tabs and placing front
on unit (Figure 10).
E. Inserting firebox into partially completed assembly (Figure 11
and Figure 12).
F. Placing top on unit.
Detailed Instructions Follow
3. Refer to Figure 7, the leg pads will have the letter "A" and "B"
stamped into the metal. Place leg pad "A" and leg pad "B" at the
bottom of each casing side. Leg pad "A" attaches to the front of the
casing side, right and to the rear of the casing side, left. Leg pad "B"
attaches to the rear of the casing side, right and to the front of the
casing side, left. Position the 3/4" flange on the leg pad against the
(2) locator dimples on the casing side. The 3/4" flange must be
facing upward, toward the top louver openings on the casing side.
Attach the two rear leg pads to the casing sides with (2) 3/8" bolts.
Attach but do not completely tighten the two front leg pads to the
casing sides with (2) 3/8" bolts. Attention: The front leg pads can
be adjusted to provide a snug fit between the casing front and the
casing sides.
4. Attach (4) leveling bolts to the bottom of the (4) legs.
5. Align the 3/8" hole at the top of the leg with the 3/8" hole in the leg
pad. Attention: For proper positioning of the leg to the leg pad the
(2) 1-1/2" top edges of the leg must be placed flush and parallel to
the (2) edges on the leg pad. Attach leg to leg pad by inserting (1)
1" bolt through the leg pad and into the leg, secure bolt with 1/4"
nut.
6. Insert (2) 3/8" bolts into the (2) holes on the edges of the casing
sides. The bolts should only be threaded half-way into the holes in
order to allow for clearance when the casing back is attached to the
casing sides.
7. Refer to Figure 8, attach casing support to rear cover with (4) 10 x 1/2"
screws. The rear cover has (4) keyholes for attachment to the casing
sides. Stand the casing sides on the floor with the (2) bolts attached halfway into the edges of the rear cover positioned at the rear. The large
diameter holes in the keyholes of the rear cover will be toward the floor.
Working with one casing side at a time, place the large diameter holes
in the keyholes over and behind both of the bolts at the same time. Push
downward on the rear cover to lock the keyholes into position behind the
bolts. Finish tightening both bolts to secure rear cover to casing side.
Repeat this procedure to secure rear cover to the second casing side.
Figure 8
Page 7R-5086
8. Position the completed portion of the casing in the approximate
location for installation as the completed assembly will be heavy.
9. Refer to Figure 9, removing protective packing foam from casing
front and window. Remove the (1) 3/4" bolt and (1) 1/4" washer
from top of window. Remove (1) 3/8" bolt and 1 - 5/8" x 3/4"
retaining tab from bottom of window. Remove the window from
casing front. Remove the protective sheet of foam from the casing
front.
Place the window into the casing front. Attach the top of the
window to the casing front with (1) 1/4" washer and (1) 3/4" bolt.
Place the 1 -5/8" x 3/4" retaining tab into the locator notch on the
bottom of the casing front. Attach the bottom of the window to the
casing front by inserting (1) 3/8" bolt through retaining tab and into
locator notch.
10. Attach the (4) 1-1/4" x 1/2" retaining tabs to the casing front with
(4) 3/8" bolts. The retaining tabs should be positioned downward.
11. Refer to Figure 10, attach casing front to outer casing by using the
(4) retaining tabs on the casing front. The (2) top, retaining tabs on
the casing front will be placed behind the (2) top, locator tabs on the
front of the casing sides. The (2) bottom, retaining tabs will be
inserted into the (2) 9/16" slots on the front, leg pads. Place the top,
retaining tabs behind the top, locator tabs as you pivot inward the
bottom of the casing front in order to insert the bottom, retaining
tabs into the slots.
Figure 10
12. The following procedure will provide a snug fit between the casing
front and the casing sides. Grasp the right, front leg, push inward on
the leg in order to provide a snug fit between the casing front and the
casing side. Continue to hold the right, front leg as you completely
tighten the (2) 3/8" bolts that attach the leg pad to the right, casing
side. Repeat procedure for left, front leg to achieve a snug fit between
the casing front and the casing side.
13. Remove the casing front from the outer casing.
14. Refer to Figures 11 and 12, the appliance firebox can now be inserted
into the outer casing. Center the firebox in the outer casing. Atten-
tion: Remove (1) Phillips-head screw in the top of the valve cover.
The screw is used to secure the valve cover in place during shipping.
The (1) Phillips-head screw can be discarded.
Page 8 R-5086
15. Attach casing front to outer casing as described in Step 11.
16. Place the casing top onto the outer casing. The casing top nests into
the outer casing.
17. Insert center grille, left grille and right grille into casing top.
Figure 11
Page 9R-5086
Delayed Ignition Reset Switch Assembly (Figure 14)
Attach black wire from REMOTE/OFF/ON switch to the front 1/4" male
tab on the reset switch. Attachment of black wire onto the reset switch is
done in conjunction with the preceding steps for Installation of Wire
Channel Assembly. Black wire on the back of the reset switch is attached
to the TH/TP terminal on gas valve (this connection is factory installed).
The reset switch can be activated if the main burner has a delayed ignition.
The right, relief door is connected by a metal wire to a cotter pin that is
inserted into the reset switch. When a delayed ignition occurs the right,
relief door pivots upward, the metal wire pulls the cotter pin out of the
reset switch and the main burner is shut OFF.
Whenever the delayed ignition reset switch is activated you must
contact a qualified service person to determine the cause for the
delayed ignition reset switch to be activated.
Under no circumstances should combustible materials (including siding)
be closer than 2" from the top of the 6 5/8" pipe or closer than 1" on the
side and bottom.
Cutting the Hole (Figure 15)
After the appliance has been positioned in its permanent location, the hole
through the exterior wall of the house can be cut. This hole needs to be 10"
high x 10" wide square with its center line determined by the amount of
vertical arise and horizontal run of the termination. When locating the
hole it must be noted that the bottom of the cap must be 12" above the
ground level, and top of the cap must be no less than 18" below a
combustible projection, and no closer than 9" to any wall running parallel
to vent termination.
Figure 14
Replacement of cotter pin into delayed ignition reset switch assembly by
a qualified service person.
1. Lower valve cover.
2. The reset switch is located behind the right side of the valve cover.
3. Verify the metal cable with attached cotter pin has free movement.
4. Depress the metal lever arm located on the front of the reset switch.
5. With the metal lever arm depressed, insert cotter pin into the clearance
hole on the right side of the bracket and into the clearance hole on the
left side of the bracket.
Attention: The tip of the cotter pin must remain flat. The tip of
the cotter pin must never be bent-over. If the tip of the cotter pin
is bent-over it could prevent the delayed ignition reset switch
from functioning during a delayed ignition.
6. Replacement of cotter pin into delayed ignition reset switch assembly
is completed.
Reassembly and Resealing Gas Accumulation Relief System
(Relief Doors) and Combustion Chamber
Whenever the relief doors are pivoted open by a delayed ignition in the
main burner, the relief door gaskets and combustion chamber must be
examined by a qualified service person for damage. All damaged gaskets
on the relief doors and combustion chamber must be replaced by a
qualified service person. If damage occurs to the combustion chamber, it
must be replaced by a qualified service person. Contact Empire Comfort
Systems, Inc. for replacement parts.
Sidewall Venting Installation
The maximum vertical and horizontal distances for one (1) 90° elbow are
25 feet and 12 feet, respectively. Vertical dimensions are based on top of
fireplace to centerline of pipe. Horizontal dimensions are based on
centerline of pipe to termination.
CAUTION: Total vertical run MUST BE completed before starting
horizontal run. Horizontal chimney run must slope upward (away
from fireplace)1/4" per foot and vent termination must be level.
Page 10 R-5086
Venting Graph (Dimensions in Feet) (Figure 16)
1. Determine the height of the center of the termination. Using this
dimension on the Venting Graph, locate the point it intersects with the
slanted graph line, or the right edge of the graph.
2. From the point of this intersection, draw a vertical line to the bottom
of the graph.
3. Adjust the indicated maximum dimension for additional elbows if
necessary.
4. Position the unit so that maximum horizontal run is not exceeded.
Venting Must Be Within Shaded Area
To Use the Vent Graph
EXAMPLE A:
If the vertical rise from the appliance outlet is 21 feet, the horizontal run
to the outer wall flange of the vent termination must not exceed 4 feet with
(1) 90° elbow.
EXAMPLE B:
If the vertical rise from the appliance outlet is 14 feet, the horizontal run
to the outer wall flange of the vent tremination must not exceed 11 feet
with (1) 90° elbow.
SPECIAL NOTE: For each 45 degree elbow installed in the horizontal
run, the length of the horizontal run MUST be reduced by 18 inches
(45cm). This does not apply if the 45 degree elbows are installed on the
vertical rise of the vent system.
Example: According to the chart the maximum horizontal run is 12 feet
and if two 45 degree elbows are required in the horizontal run it must be
reduced to 9 feet.
The maximum number of 45 degree elbows permitted per side wall
installation is two. These elbows can be installed in either the vertical rise
or horizontal run.
Figure 16
Venting Requirements (Figure 17)
Minimum vertical rise from appliance outlet = 24 inches (610mm)
Attention: All vent runs must have a minimum VERTICAL rise of
two feet. If the vent run is directly behind the appliance, you must
attach Simpson Dura-Vent 36" snorkel, part number SD-981 on the
exterior of the building.
Maximum vertical rise from appliance outlet = 25 feet (7.62m), the
restrictor plate may be used above 10 feet.
Maximum horizontal run from appliance outlet = 12 feet (3.66m)
Maximum vertical rise and horizontal run is a combined total of 25 feet
(7.62m)
Maximum elbows = (2) 90°, for the second elbow subtract 5 feet from a
horizontal run.
Figure 17
Page 11R-5086
Installation of Restrictor Plate (Figure 18)
The restrictor plate is to be used only in a completely vertical vent
installation. The restrictor plate can be used when the vertical vent rise is
between 10 feet and 25 feet.
In a vertical vent rise the rear (yellow) flame on the main burner can be
reduced due to the drawing action from the flue exhaust pipe and the air
inlet pipe. A decrease in the height or the appearance of the yellow flame
may occur when the vertical vent rise is between 10 feet and 25 feet. To
enhance the yellow flame on the main burner, the restrictor plate can be
installed beneath the vent elbow on the appliance air drop.
Please use the following steps to install the restrictor plate.
1. If attached, remove the vent pipe from the vent elbow on the appliance.
2. Remove the vent elbow from the appliance air drop by removing (4)
1/2" hex-head screws from vent elbow.
3. Align clearance holes on restrictor plate with screw holes on appliance
air drop. The gasket on the restrictor plate should be positioned
upward when the restrictor plate is placed onto appliance air drop.
4. Align clearance holes on vent elbow with clearance holes on restrictor
plate and screw holes on appliance air drop.
5. Attach vent elbow and restrictor plate to appliance air drop. Fasten (4)
1/2" hex-head screws from Step 2 through clearance holes on vent
elbow and restrictor plate and into screw holes on appliance air drop.
Attention: Apply furnace cement to the top, exterior edge on the cast
iron flue outlet.
6. Installation of restrictor plate is completed.
Attention: See Page 26 to order restrictor plate, part number CI-235.
Service Notes
--------------------
Figure 18
APPLY FURNACE
CEMENT TO TOP,
EXTERIOR EDGE
ON CAST IRON
FLUE OUTLET
Page 12 R-5086
Termination Clearances (Figure 19)
Termination clearance for buildings with combustible and noncombustible exteriors.
Figure 19
Vertical Sidewall Installations
Important! Minimum clearance between vent pipes and combustible materials is one inch (1") (25mm) on, bottom and sides and (2") (51mm) on top.
Important! When vent termination exits through foundation less than 20" below siding outcrop, the vent pipe must flush up with the siding. SD985
termination cap must also be used.
Imformation on Various Venting Routes and Components
Important: It is always best to locate the appliance in such a way that minimizes the number of offsets and horizontal vent length.
Since it is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust, certain limitations
as to vent configurations apply and must be strictly adhered to.
The graph showing the relationship between vertical and horizontal side wall venting will help to determine the various vent lengths allowable.
The horizontal vent run refers to the total length of vent pipe from the vent elbow of the appliance to the face of the outer wall.
Page 13R-5086
Vent Clearances (Figure 20)
A = *Clearance above grade, veranda, porch, deck or balcony [*12
inches (30cm) minimum]
B = clearance to window or door that may be opened [*9 inches
(23cm) minimum for appliances < 50,000 Btuh (14.6kW)
C = clearance to permanently closed window [minimum 12 inches
(30cm) recommended to prevent condensation on window]
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (61cm) from the top of
the terminal
E = clearance to unventilated soffitt [24 inches 61cm) minimum]
F = clearance to outside corner [12 inches (30cm) minimum]
G = clearance to inside corner [9 inches (22.5cm) minimum]
H = *not to be installed above a meter/regulator assembly within 3
feet (90cm) horizontally from the center-line of the regulator
I = clearance to service regulator vent outlet [*6 feet (1.8m)
minimum]
Figure 20
J = clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other appliance [*12 inches (30cm)
minimum for appliances ≤ 100,000 Btuh (30 kW)
36 inches (90cm) minimum for appliances > 100,000 Btuh
(30kW)]
K = clearance to a mechanical air supply inlet [* 6 feet (1.8m)
minimum]
L= †clearance above paved sidewalk or a paved driveway located
on public property [*7 feet (2.1m) minimum]
M = clearance under veranda, porch, deck, or balcony [*12 inches
(30cm) minimum¥]
† a vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings*
¥ only permitted if veranda, porch, deck, or balcony, is fully open
on a minimum of 2 sides beneath the floor*
* as specified in CGA B149 Installations Codes or ANSI Z223.1.
Note: Local Codes or Regulations may require different
clearances.
Page 14 R-5086
Page 15R-5086
Figure 23
Installing Firestops (Figures 24, 25, 26 and 27)
Firestops are required for safety whenever the vent system passes
through an interior wall, an exterior wall, or a ceiling. These firestops act
as a firebreak heat shield and as a means to insure that minimum
clearances are maintained to the vent system.
Horizontal runs in the vent system which pass through either interior or
exterior walls, require the use of wall firestops on both sides of the wall
through which the vent passes.
Position the firestops on both sides of the 10 inch x 10 inch hole,
previously cut. Secure with nails or screws. Continue the vent run
through the firestops. (See Figure 24)
Position a plumb bob directly over the center of the vertical vent
component and mark the ceiling to establish the center point of the vent.
Drill a hole or drive a nail through this center point and check the floor
above for any obstructions such as wiring or plumbing runs. Reposition
the appliance and vent system, if necessary, to accommodate ceiling
joists and/or obstructions.
Cut a 10 inch x 10 inch hole through the ceiling, using the center point
previously marked. Frame the hole with framing lumber the same size
as the ceiling joists. (See Figure 25 ) If the area above the ceiling is NOT
an attic, position and secure the ceiling firestop (SD-963) on the ceiling
side of the previously cut and framed hole. (See Figure 26) If the area
above the ceiling IS an attic, position and secure the firestop on top of
the previously framed hole. (See Figure 27)
NOTE: Remove insulation from the framed area in the attic before
installing the firestop and/or vent stop and/or vent pipes.
Figure 25
Figure 26
Figure 24
Vertical runs of this system which pass through ceilings require the use
of ONE (1) ceiling firestop at the hole in each ceiling through which the
vent passes.
Page 16 R-5086
Figure 27
Horizontal Terminations (Figure 28)
Attach and secure the termination to the last section of horizontal
venting by rotating and interlocking the ends as previously described.
NOTE: Termination cap should pass through the wall firestop from
the exterior of the building. Adjust the termination cap to its
final exterior position on the building.
WARNING: Termination cap must be positioned so that the
arrow is pointing up.
Using the termination cap in the center of the square hole, attach the
termination cap with the four wood screws provided. Before attachment
of the termination, run a bead of silicone sealant rated above 250°F on
its outside edge too, so as to make a seal to that exterior wall.
NOTE: Wood screws can and should be replaced with appropriate
fasteners for use on stucco, brick, concrete or other types of
siding.
CAUTION: If exterior walls are finished with vinyl siding, it is
necessary to install the vinyl siding shield (SD-950).
Vinyl siding shield (SD-950) will be installed between the vent
termination and the exterior wall. (See Figure 28) This horizontal vent
termination bolts onto the flat portion of the vinyl siding standoff, so an
air space will exist between the wall and the termination cap.
Figure 28
Vertical Terminations (Figures 29, 30 and 31)
Locate and mark the center point of the venting pipe. Using a nail on the
underside of the roof and drive this nail through this center point. Make
the outline of the roof hole around this center point.
NOTE: Size of the roof hole dimensions depend on the pitch of the
roof. There must be a 1 inch clearance (25mm) to the vertical
pipe sections. This clearance is to all combustible material.
Cover the opening of the vent pipe and cut and frame the roof hole. Use
framing lumber the same size as the roof rafters and install the frame
securely. Flashing anchored to frame must withstand high winds. The
storm collar is placed over this joint to make a water-tight seal. Nonhardening sealant should be used to completely seal this flashing
installation.
Determining Minimum Vent Height Above the Roof.
WARNING: Major U.S. building codes specify minimum chimney
and/or vent height above the roof top. These minimum heights are
necessary in the interest of safety. These specifications are
summarized in Figure 29.
Page 17R-5086
Page 18 R-5086
Vertical runs of this vent systems must be supported every 4 feet above
the appliance flue outlet by wall brackets attached to the 6- 5/8 inch vent
pipe and secured with nails or screws to structural framing members.
Page 19R-5086
Replacement of Gasket on Glass Panes (Figure33)
1. Remove casing top from outer casing.
2. Remove casing front from outer casing.
3. Lower valve cover on firebox.
4. Release two door latches at bottom of firebox.
5. Grasp bottom of glass frame, pull forward until bottom of glass
frame is removed from glass frame guide and pull downward until
glass frame is removed from glass frame support top.
6. Place glass frame assembly on a non-abrasive surface. The exterior
of the glass frame assembly should be facing the non-abrasive
surface.
7. Remove the (6) screws on the glass frame assembly.
8. Remove the (2) 1" x 13-3/4" divider brackets from the glass frame
assembly.
9. Remove the gasket that is to be replaced on the glass pane. Clean
the glass pane before the new gasket is attached.
10. Remove the backing material from the gasket.
11. Starting in a corner of the glass pane, place the gasket over the edge
of the glass pane. The gasket should be equally divided between
the front and back of the glass. Continue to attach the gasket until
the four edges of the glass pane are gasketed.
12. When the glass panes are replaced into the glass frame assembly,
the corner of the glass pane where the gasket was started and ended
should be placed to the bottom of the glass frame assembly.
13. Replace and attach the (2) 1" x 13-3/4" divider brackets onto the
glass frame assembly with the (6) screws from Step 7.
14. Grasp bottom of glass frame, push upward and insert glass frame
into glass frame support top, push inward and insert glass frame
into glass frame guide.
15. Attach two door latches to bottom of firebox.
16. Replace casing front onto outer casing.
17. Replace casing top onto outer casing.
18. Replacement of gasket on glass panes is completed.
Page 20 R-5086
Main Burner Flame Pattern (Figure 36 and Figure 37)
Figure 36 shows a correct main burner flame pattern. Figure 37 shows an
incorrect main burner flame pattern.
Air Shutter Adjustment
An air shutter adjusting screw is located on the exterior, bottom of the
inner body. Screw air shutter adjusting screw IN to close air shutter top
(increase yellow flame). Screw air shutter adjusting screw OUT to open
air shutter top (decrease yellow flame).
Correct Main Burner Flame
Figure 36
If main burner flame pattern is incorrect, as shown in Figure 37
• See Troubleshooting, page 25.
Cleaning and Maintenance / Main Burner
Warning: Turn off heater and let cool before cleaning.
After use, cleaning of the main burner may be required for the proper
flame. The main burner may be cleaned by applying air pressure to the
ports on the main burner.
Cleaning the Log Set and Firebox
During the annual inspection and maintenance appointment, the service
person should clean dust, lint, and any light accumulation from the logs
and the firebox area. An extra-soft brush should be used on the logs as
they are extremely fragile; a vacuum cleaner may be used on the firebox.
If at any time the logs cannot be removed or installed without forcing,
the cause must be found. The logs must never be forced.
CAUTION: The ceramic logs are durable when handled and installed
properly. However, they are delicate and may be damaged easily if not
handled with care. Handling damage to the ceramic logs is not covered
by warranty.
DO NOT HANDLE LOGS WHILE THEY ARE HOT. ALLOW
PLENTY OF TIME FOR THE APPLIANCE TO COOL COMPLETELY
BEFORE HANDLING.
OPERATING INSTRUCTIONS
CIDV-30 ON/OFF/REMOTE Switch
CIDV-30 is equipped with an ON/OFF/REMOTE switch which is
located on the wiring chase. A wire harness is attached to the ON/OFF/
REMOTE switch. The red, black and green (wires) female push-ons
attach to the ON/OFF/REMOTE switch. At the opposite end of the wire
harness, the black and green (wires) female push-ons attach to the gas
valve. An additional green wire and the red wire, which are stripped and
bare, will attach to the 750 millivolt wall thermostat accessory, or, to one
of the other accessories that can be purchased for use with your log set.
Operation of ON/OFF/REMOTE Switch with no Accessories
To ignite main burner, turn the control knob on the gas valve from the
PILOT position to the ON position. Turn the ON/OFF/REMOTE switch
from the OFF position to the ON position. The additional green wire and
red wire, which are stripped and bare are not used.
Operation of ON/OFF/REMOTE Switch with Accessories
750 Millivolt Wall Thermostat, GWSG-T
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the wall thermostat. Turn the ON/OFF/
REMOTE switch on the wiring chase to the REMOTE position. Set the
wall thermostat to the desired temperature.
It is important to use wire of a gauge proper for the length of the wire:
RECOMMENDED WIRE GAUGES
Maximum Wire
Length Gauge
1' to 10' 18
10' to 25' 16
25' to 35' 14
Incorrect Main Burner Flame
Figure 37
Wall Switch, FWS-1
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the wall switch. Turn the ON/OFF/
REMOTE switch on the wiring chase to the REMOTE position. Pivot
the rocker switch on the FWS-1 to the ON position.
Battery Operated Remote Control, FRBC-1 and FRBTC-1
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the remote receiver that is a component
in the FRBC-1 and FRBTC-1. Turn the ON/OFF/REMOTE switch on
the wiring chase to the REMOTE position. Follow instructions in the
FRBC-1 and FRBTC-1 to complete installation.
Note: If batteries fail in FRBC-1 or FRBTC-1, and immediate heat is
desired, turn the ON/OFF/REMOTE switch on wiring chase from the
REMOTE position to the ON position.
Electric (120 volt) Operated Remote Control, FREC-1
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the wires on remote receiver that is a
component in the FREC-1. Turn the ON/OFF/REMOTE switch on the
wiring chase to the REMOTE position. Follow instructions in the
FREC-1 to complete installation.
Note: If electric (120 volt) fails in FREC-1, and immediate heat is
desired, turn the ON/OFF/REMOTE switch on wiring chase from the
REMOTE position to the ON position.
Page 21R-5086
Wiring of ON/OFF/REMOTE Switch with 750 Millivolt Wall
Thermostat Accessory and Another Accessory
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the 750 millivolt wall thermostat AND
to the remote receiver that is a component in the FRBC-1, FREC-1 OR
to the FWS-1, wall switch.
1. Connect (1) wire from the 750 millivolt wall thermostat and (1) wire
from appropriate accessory to the GREEN, stripped and bare wire
from the ON/OFF/REMOTE wire harness.
2. Connect (1) wire from the 750 millivolt wall thermostat and (1) wire
from appropriate accessory to the RED, stripped and bare wire from
the ON/OFF/REMOTE wire harness.
Note: When the appliance is in the MANUAL mode and the batteries
fail in the FRBC-1 or if the electric (120 volt) fails in the FREC-1, and
immediate heat is desired, turn the ON/OFF/REMOTE switch on
wiring chase from the REMOTE position to the ON position.
Manual Operation
1. Turn ON/OFF/REMOTE switch on wiring chase to REMOTE
position.
2. Turn wall thermostat OFF.
3. Turn accessory, FRBC-1, FREC-1 or FWS-1, ON. Appliance is now
in the manual mode. You must turn the appliance ON or OFF with
appropriate accessory.
Wall Thermostat Operation
1. Turn the ON/OFF/REMOTE switch on wiring chase to REMOTE
position.
2. Turn accessory, FRBC-1, FREC-1 or FWS-1, OFF.
3. Turn wall thermostat ON and set appropriate temperature. Wall
thermostat will cycle the appliance ON and OFF.
Installation of Remote Receiver (Figure 38)
1. Attach, from left to right, the slide-on cover plate onto the remote
receiver. ON will be to the top and OFF will be to the bottom on the
slide-on cover plate.
2. Push the receiver slide button onto the receiver slide switch. Reverse
installation of the slide button if it is off center.
3. Attach velcro loop on the left side of the valve cover support.
4. Attach velcro hook onto remote receiver. The word TOP on the
remote receiver should be to the top when installed onto valve cover
support.
5. Attach velcro hook on remote receiver onto velcro loop on valve
cover support.
Page 22 R-5086
Initial Lighting (Figure 40)
Upon completing the gas line or turning the gas valve "ON" after it has
been in the "OFF" position, a small amount of air will be in the lines.
When first lighting the appliance, it will take a few minutes for the lines
to purge themselves of this air. Once the purging is complete, the
appliance will light and operate satisfactorily.
Subsequent lightings of the appliance will not require such purging if the
gas valve is not turned to "OFF."
Standing Pilot Operation
1. Follow the SAFETY and LIGHTING INSTRUCTIONS for standing
pilot controls found in this manual and on labels found attached to
the appliance.
CAUTION: During the initial purging and subsequent lightings,
never allow the gas valve control knob to remain depressed in the
"pilot" position without pushing the piezo ignitor button at least
once every second.
2. During the heating season, leave the control valve knob in the "ON"
position. This will allow the pilot flame to remain lit. Turn the burner
flame on or off with the appliance ON/OFF rocker switch, wall
switch, remote control kits or 750 millivolt wall thermostat.
NOTE: The gas control valve allows you to increase or decrease the
height of the main burner flame. The control valve has a pressure
regulator with a knob as shown in Figure 40. Rotate the knob clockwise
to "HI" to increase the flame height and counterclockwise to "LO" to
decrease the flame height.
3. When the heating season is over, turn the on/off switch to "OFF" and
the control valve to "OFF". The system, including the pilot light, will
be shut down.
Page 23R-5086
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance (if applicable).
4. Lower valve cover.
5. Push in gas control knob slightly and turn clockwise
to "OFF".
6. Wait ten (10) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above. If you don't
smell gas, go to the next step.
7. Find pilot - The pilot is
attached to the main
burner behind the front
log.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to inspect the appliance and to replace any part
of the control system and any gas control which has
been under water.
8. Turn knob on gas control counterclockwise
to "PILOT."
9. Push in gas control knob all the way and hold in.
Repeatedly push the piezo ignitor button until
pilot is lit. Continue to hold the control knob in for
about one (1) minute after the pilot is lit. Release
knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 9.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to "OFF" and call your
service technician or gas supplier.
10. Turn gas control knob counterclockwise to
"ON".
11. Raise valve cover.
12. Turn on all electric power to the appliance (if applicable).
13. Set thermostat to desired setting.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
2. Turn off all electric power to appliance if service is to be
performed (if applicable).
3. Lower valve cover.
Page 24 R-5086
4. Push in gas control knob slightly and turn clockwise to "OFF". Do not force.
5. Raise valve cover.
STANDING PILOT-TROUBLE SHOOTING
With proper installation and maintenance, your new Direct Vent Fireplace should provide years of trouble-free service. If you do experience a
problem, refer to the Trouble Shooting Guide below. This guide will assist a qualified service person in the diagnosis of problems and the corrective
action to be taken.
1. Spark ignitor will not light pilot after repeated depressing of
piezo ignitor button.
a. Defective ignitor (no spark at electrode) - Check for spark at
electrode and pilot; if no spark and electrode wire is properly
connected, replace ignitor.
b. No gas or low gas pressure.
- Check remote shut off valves from fireplace. Usually there
is a valve near the main. There can be more than one (1)
valve between the fireplace and main.
- Low pressure can be caused by a variety of situations such
as a bent line, too narrow diameter of pipe, or low line
pressure. Consult with plumber of gas supplier.
c. No LP in tank.
- Check LP (propane) tank. Refill tank.
2. Pilot will not stay lit after carefully following lighting
instructions.
a. Defective thermocouple.
- Check that pilot flame impinges on thermocouple. Clean
and/or adjust pilot for maximum flame impingement.
- Ensure that the thermocouple connection at the gas valve
is fully inserted and tight (hand tight plus 1/4 turn) faulty
themopile if reading is below specified minimum.
- Disconnect the thermocouple from the valve, place one
millivolt meter lead wire on the tip of the thermocouple and
the other meter lead wire on the thermocouple copper lead.
Start the pilot and hold the valve knob in. If the millivolt
reading is less than 15 mv, replace the thermocouple.
b. Defective valve.
- If thermocouple is producing more than 15 millivolts,
replace faulty valve
3. Pilot burning, no gas to burner, valve knob "ON", on/off
switch "ON."
a. "On/Off" switch, wall switch, or wires defective.
- Check "on/off" switch and wires for proper connections.
Place jumper wires across terminal at switch - if burner
comes on, replace defective switch. If OK, place jumper
wires across switch wires at gas valve-if burner comes on,
wires are faulty or connections are bad.
b. Thermopile may not be generating sufficient milli-voltage.
- If the pilot flame is not close enough physically to the
thermopile, adjust the pilot flame.
- Be sure the wire connections from the thermopile at the gas
valve terminals are tight and the thermopile is fully inserted
into the pilot bracket.
- Check the thermopile with a millivolt meter. Take the
reading at TH-TP & TP terminals of the gas valve. The meter
should read 325 millivolts minimum, while holding the
valve knob depressed th the pilot position, with the pilot lit,
and the ON/OFF switch in the OFF position. Replace the
faulty thermopile if the reading is below the specified
minimum.
-With the pilot in the ON position, disconnect the thermopile
leads from the valve. Take a reading at the thermopile leads.
The reading should be 325 millivolts minimum. Replace the
thermopile if the reading is below the minimum.
c. Defective valve.
- Turn valve knob to "ON." Place ON/OFF switch to "ON."
Check with millivolt meter at thermopile terminals. Millivolt
meter should read greater than 100 M.V. If the reading is
okay and the burner does not come, replace the gas valve.
d. Plugged main burner orifice.
- Check main burner orifice for blockage, clean main burner
orifice.
4. Frequent pilot outage problem.
a. Pilot flame may be too high or too low, or blowing (high),
causing pilot safety to drop out.
- Clean and adjust flame for maximum flame impingement
on the thermocouple. Follow lighting instructions carefully.
5. The pilot and main burner extinguish while in operation.
a. No LP (Propane) in tank.
- Check LP (Propane) tank. Refill fuel tank.
b. Inner vent pipe leaking exhaust gases back into system.
- Check for leaks.
c. Glass too loose, gasket leaks in corners after usage.
- Be certain glass assembly is installed correctly and tighten
corner.
d. Horizontal vent improperly pitched.
- The horizontal vent cap should slope down only enough to
prevent any water from entering the unit. The maximum
downwarda slope is 1/4 inch.
e. Bad thermopile or thermocouple.
- Replace if necessary.
f. Improper vent cap installation.
- Check for proper installation and freedom from debris or
blockage.
6. Glass soots.
a. Flame impingement on logs.
- Adjust the log set so that the flame does not excessively
impinge on it.
b. Improper air shutter adjustment.
- Adjust the air shutter.
7. Flame lifts off main burner.
a. Insufficient oxygen being supplied.
- Check to make sure vent cap is installed properly and free
of debris. Make sure that vent system joints are tight and
have no leaks.
- Check to make sure that no material has been placed at the
burner base.
- Be sure glass is tightened properly on unit, particularly on
top corners.
Page 25R-5086
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
Index Part
No. Number Description
1 R-3436 REMOTE/OFF/ON SWITCH
2 CI-329 WIRE CHANNEL
3 CI-331 CHANNEL DIVIDER
4 CI-330 CASING SUPPORT
5 CI-307 REAR COVER
6 M-160 GASKET - VENT ELBOW
7 CI-332 AIR DROP ASSEMBLY
8 CI-364 RELIEF DOOR ASSEMBLY
9 CI-375 RELIEF DOOR BRACKET (2
REQUIRED)
10 CI-363 INNER TOP ASSEMBLY
11 CI-273 GLASS FRAME SUPPORT TOP
12 M-163 FLUE CONNECTOR TUBE GASKET (3
REQUIRED)
13 CI-274 SIDE SHIELD (2 REQUIRED)
14 CI-275 INNER BODY
15 CI-324 INTERNAL BAFFLE
16 CI-355 GLASS ASSEMBLY - SIDE (2
REQUIRED)
17 CI-356 GLASS ASSEMBLY - FRONT
18 CI-354 GLASS FRAME ASSEMBLY
19 R-2708 PIEZO IGNITOR
20 CI-143 VALVE COVER ASSEMBLY
21 CI-253 MAGNET ASSEMBLY (2 REQUIRED)
22 R-3318 GAS VALVE - NAT
22 R-3319 GAS VALVE - LPG
23 R-1259 3/8 NPT X 3/8 NPT STREET ELBOW
24 CI-016 MANIFOLD ASSEMBLY
25 P-86-38N ORIFICE-NAT
25 P-86-54L ORIFICE-LPG
26 * CI-008 LEG PAD-A (2 REQUIRED)
27 * CI-009 LEG PAD-B (2 REQUIRED)
28 CI-272 GLASS FRAME GUIDE
29 CI-362 INNER BOTTOM FACE ASSEMBLY
30 CI-145 DELAYED IGNITION RESET SWITCH
ASSEMBLY
31 R-4053 DOOR LATCH (2 REQUIRED)
Index Part
No. Number Description
32 CI-361 INNER BOTTOM ASSEMBLY
33 M-164 GASKET - MANIFOLD
34 M-157 GASKET - SEAL BRACKET
35 DVF-039 SEAL BRACKET
36 CI-257 AIR SHUTTER BODY
37 CI-023 BURNER BRACKET - RIGHT
38 R-3758 ADJUSTING SCREW
39 CI-025 AIR SHUTTER TOP
40 R-5278 BURNER
41 CI-022 BURNER BRACKET - LEFT
42 R-3473 THERMOCOUPLE
43 CI-018 PILOT TUBING
44 R-5285 THERMOPILE
45 R-3465 PILOT WITH ORIFICE (NAT ONLY)
45 R-3466 PILOT WITH ORIFICE (LPG ONLY)
46 CI-338 LOG SUPPORT ASSEMBLY
47 R-3642 FRONT LOG
48 R-3644 TOP LOG
49 R-3643 REAR LOG
NOT SHOWN R-5143 PILOT ASSEMBLY - NAT. WITH
THERMOPILE THERMOCOUPLE
NOT SHOWN R-5144 PILOT ASSEMBLY - LPG WITH
THERMOPILE THERMOCOUPLE
NOT SHOWN CI-350 CABLE ASSEMBLY (DELAYED
IGNITION RESET SWITCH)
NOT SHOWN R-3766 WIRE ASSEMBLY (DELAYED
IGNITION RESET SWITCH)
NOT SHOWN R-3765-A WIRE ASSEMBLY
NOT SHOWN R-4505 TUBE OF FURNACE CEMENT
NOT SHOWN * CI-007 RETAINING TAB (4 REQUIRED)
NOT SHOWN * R-3747 LEVELING BOLT (4 REQUIRED
NOT SHOWN CI-235 RESTRICTOR PLATE USED IN A
VERTICAL RISE BETWEEN 15' AND
25'
* PART IS INCLUDED IN THE HARDWARE PACKAGE AND IS
USED IN THE ASSEMBLY OF THE STOVE CASTING
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
How To Order Repair Parts...
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through
the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your
equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate
illustration and list. Be sure to give all this information . . .
Heater Model Number Part Description
Heater Serial Number Type of Gas (Propane or Natural)
Part Number
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Page 26 R-5086
19
29
30
Page 27R-5086
Page 28 R-5086
OPTIONAL BLOWER CIB-2
Direct Vent Fireplace CIDV-30
Installing Optional CIB-2 Blower
1. Loosen, but do not remove, (4) hex-head screws located on the
exterior, bottom of the appliance.
2. Position the blower assembly at the rear of the appliance. The
blower assembly has (4) keyholes for attachment to the exterior,
bottom of the appliance.
3. Place the large diameter holes in the keyholes over and behind the
(4) hex-head screws that were loosened in Step 1. Push inward on
the blower assembly to lock the keyholes into position behind the
screws. Tighten (4) hex-head screws to secure blower assembly to
exterior, bottom of the appliance.
4. Remove wire channel from channel divider by removing (2) 10 x
1/2" screws. Note: If optional blower is being installed during
initial installation of appliance, the wire channel will not be
attached to rear cover. (Refer to Installation of Wire Channel
Assembly, Page 9)
5. Remove channel divider from rear cover by removing (2) 10 x
1/2" screws.
6. Attach fan control to OFFSET, fan control bracket (Part 9B, Page
28) with (2) 6 x 1/4" screws provided in hardware package.
7. Attach fan control with bracket onto air drop with (2) 10 x 1/2"
screws provided in hardware package.
8. Route fan control wires through 1/2" extruded hole on channel
divider. Attach fan control wires to fan control.
9. Attach channel divider with (2) 10 x 1/2" screws from Step 5.
10. Route wires from fan control and ON/OFF/REMOTE switch
within wire channel.
11. Attach wire channel to channel divider with (2) 10 x 1/2" screws
from Step 4. (Refer to Installation of Wire Channel Assembly,
Page 9)
12. Insert AUTO/OFF/ON switch into rectangular notch on valve
bracket. Be sure to insert AUTO/OFF/ON switch with letters
(words) upright. (See wiring diagram)
13. Attach 1/4" push-on terminal from blue wire on the fan control
to the AUTO (top) tab on the switch.
14. Attach 1/4" push-on terminal from black wire to the OFF
(middle) tab on the switch.
15. Attach 1/4" push-on terminal from white wire on the fan
control to the ON (bottom) tab on the switch.
16. Installation of optional CIB-2 blower is completed.
Fan Control
The fan control is a non-adjustable automatic type The fan control will
require between 5 and 10 minutes of main burner operation before
the fan control "closes" and activates the blower. The blower will
continue to run between 5 and 10 minutes after the main burner shuts
off, before the fan control "opens" and deactivates the blower.
Wiring
The appliance, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical
Code, CSA C22.1, if an external electrical source is utilized. This
appliance is equipped with a three-prong [grounding] plug for
your protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this plug. For an
ungrounded receptacle, an adapter, which has two prongs and a wire
for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screws.
With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded.
CAUTION: Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
WARNING:
Unplugging of blower accessory will not stop the heater from
cycling. To shut heater off: Turn temperature dial or
thermostat to lowest setting. Turn knob on gas control to
"OFF", depressing slightly. Do not force.
Page 29R-5086
Cleaning
The blower wheel will collect lint and could require cleaning once
a year. If the air output decreases or the noise level increases, it
indicates a dirty wheel.
Blower Motor
The blower motor does not have oiling holes. Do not attempt to oil
blower motor.
PARTS LIST
Index Part
No. No. Description
1 R-1454 Brass Bushing (4 Required)
2 R-1499 Rubber Grommet (4 Required)
3 CI-002 Blower Housing
4 R-1517 Tinnerman Clip (4 Required)
5 R-2804-A Blower Assembly
6 CI-003 Blower Housing Cover
7 R-2099 Cord Set
8 R-3767-A Wire Harness
9A CI-004 Fan Control Bracket
(Use with CIBV-30, CIVF-25,
CIVF-25C Only)
9B CI-325 Fan Control Bracket
(Use with CIDV-30 Only)
10 R-2503 Fan Control
11 R-2805 Auto/Off/On Switch
12 CI-220 Fan Control Shield
(Use with CIVF-25 only)
13 R-1410 Bushing 7/8" D
Page 30 R-5086
Loading...