Page 1
INSTALLATION INSTRUCTIONS
AND
OWNER'S MANUAL
UNVENTED
ROOM HEATER
MODELS
BF-10-2 BF-20-2 BF-30-2
EFFECTIVE DATE
Installer: Leave this manual with the appli-
ance.
Consumer: Retain this manual for future refer-
ence.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion
may result causing property damage, personal
injury or loss of life.
— Do not store or use gasoline or other flamma-
ble vapors and liquids in the vicinity of this or
any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
AUGUST 2006
This appliance may be installed in an aftermarket, permanently located, manufactured
(mobile) home, where not prohibited by local
codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases.
This is an unvented gas-fired heater. It uses air
(oxygen) from the room in which it is installed.
Provisions for adequate combustion and ventilation air must be provided. Refer to page 6.
WARNING: If not installed, operated and
maintained in accordance with the manufactur
er's instructions, this product could expose you
to substances in fuel or from fuel combustion
which can cause death or serious illness.
WATER VAPOR: A BY-PRODUCT OF
UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately
one (1) ounce (30ml) of water for every 1,000
Btu (.3KW's) of gas input per hour. Refer to
page 6.
-
16943-5-0806 Page 1
Page 2
TABLE OF CONTENTS
SECTION PAGE
Important Safety Information ......................................................................................................................3
Safety Information for Users of LP Gas ......................................................................................................
Introduction ..................................................................................................................................................5
Specifications ...............................................................................................................................................
Water Vapor: A By-Product of Unvented Room Heaters .............................................................................
Provisions for Adequate Combustion and Ventilation Air ...........................................................................
Gas Supply ...................................................................................................................................................7
Clearances ...................................................................................................................................................8
Optional Floor Stand Installation .................................................................................................................8
Wall Mount Installation ...............................................................................................................................
Lighting Instructions .................................................................................................................................10
Main Burner Flame Characteristics ..........................................................................................................11
Pilot Flame Characteristics .......................................................................................................................12
Thermostat Operation ................................................................................................................................12
Appliance Maintenance .............................................................................................................................13
4
5
6
6
9
Troubleshooting .........................................................................................................................................
Parts List ...................................................................................................................................................15
How to Order Repair Parts .........................................................................................................................15
Parts View ..................................................................................................................................................
Optional Blower Installation Instructions ........................................................................................... 17-18
Service Notes .............................................................................................................................................19
14
16
Page 2 16943-5-0806
Page 3
IMPORTANT SAFETY INFORMATION
THIS IS A HEATING APPLIANCE
DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.
• An unvented room heater having an input rating of
more than 6,000 Btu per hour shall not be installed in a
bathroom.
• An unvented room heater having an input rating of more
than 10,000 Btu per hour shall not be installed in a bedroom
or bathroom.
• Due to high temperatures, the appliance should be located
out of traffic and away from furniture and draperies.
• Children and adults should be alerted to the hazard of
high surface temperature and should stay away to avoid
burns or clothing ignition.
• Young children should be carefully supervised when they
are in the same room with the appliance.
• Do not place clothing or other flammable material on or
near the appliance.
• Due to high surface temperatures, keep children, clothing
and furniture away.
• WARNING: Do not use a blower insert, heat exchanger
insert or other accessory not approved for use with
heater.
• Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected
before use and at least annually by a professional service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials, etc. It
is imperative that control compartments, burners and
circulating air passageways of the appliance be kept
clean.
• DO NOT use this room heater if any part has been under
water. Immediately call a qualified service technician
to inspect the room heater and to replace any part of the
control system and any gas control which has been under
water.
• Keep appliance area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
• WARNING: ANY CHANGE TO THIS HEATER OR ITS
CONTROLS CAN BE DANGEROUS.
Any safety screen or guard removed for servicing an
appliance must be replaced prior to operating the heater.
• WARNING: Failure to keep the primary air opening(s)
of the burner(s) clean may result in sooting and property
damage.
WARNING
When used without adequate combustion and ventilation air,
heater may give off CARBON MONOXIDE, an odorless, poisonous gas.
Do not install heater until all necessary provisions are made
for combustion and ventilation air. Consult the written instructions provided with the heater for information concerning
combustion and ventilation air. In the absence of instructions,
refer to the National Fuel Gas Code, ANSI Z223.1, Section
5.3 or applicable local codes.
This heater is equipped with a PILOT LIGHT SAFETY SYSTEM designed to turn off the heater if not enough fresh air is
available.
DO NOT TAMPER WITH PILOT LIGHT SAFETY
SYSTEM!
If heater shuts off, do not relight until you provide fresh air.
If heater keeps shutting off, have it serviced. Keep burner and
control compartment clean.
CARBON MONOXIDE POISONING MAY LEAD TO
DEATH.
Early signs of carbon monoxide poisoning resemble the flu, with
headache, dizziness and/or nausea. If you have these signs, heater
may not be working properly. Get fresh air at once! Have heater
serviced.
Some people — pregnant women, persons with heart or lung dis
ease, anemia, those under the influence of alcohol , those at high
altitudes — are more affected by carbon monoxide than others.
The pilot light safety system senses the depletion of oxygen at
its location. If this heater is installed in a structure having a high
vertical dimension, the possibility exists that the oxygen supply
at the higher levels will be less than that at the heater. In this type
of application, a fan to circulate the structure air will minimize
this effect. The use of this fan will also improve the comfort level
in the structure. When a fan is used to circulate air, it should be
located so that the air flow is not directed at the burner.
-
16943-5-0806 Page 3
Page 4
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precau
tions which can protect both you and your family from an
accident. Read them carefully now, then review them point
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building, vehicle, trailer, or area.
Do that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must find out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors
in the area mask the gas odor. People may not smell the gas odor
or their minds are on something else. Thinking about smelling a
gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
by point with the members of your household. Someday
when there may not be a minute to lose, everyone's safety
will depend on knowing exactly what to do. If, after read
ing the following information, you feel you still need more
information, please contact your gas supplier.
• Use your neighbor's phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
-
SOME POINTS TO REMEMBER
• Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it
to find out what the propane odor smells like. If you suspect
that your LP-Gas has a weak or abnormal odor, call your
LP-Gas Dealer.
• If you are not qualified, do not light pilot lights, perform
service, or make adjustments to appliances on the LP-Gas
system. If you are qualified, consciously think about the
odor of LP-Gas prior to and while lighting pilot lights or
performing service or making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls
of new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or
cylinders are placed in service. Odor fade can occur in new
tanks, or reinstalled old tanks, if they are filled and allowed
to set too long before refilling. Cylinders and tanks which
have been out of service for a time may develop internal rust
which will cause odor fade. If such conditions are suspected
to exist, a periodic sniff test of the gas is advisable. If you
have any question about the gas odor, call your LP-gas dealer.
A periodic sniff test of the LP-gas is a good safety measure
under any condition.
• If, at any time, you do not smell the LP-Gas odorant and
you think you should, assume you have a leak. Then take
the same immediate action recommended above for the oc
casion when you do detect the odorized LP-Gas.
• If you experience a complete "gas out," (the container is un
der no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air through openings such as pilot light orifices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having
it refilled before it is completely empty.
-
-
Page 4 16943-5-0806
Page 5
INTRODUCTION
Instructions to Installer
1. Installer must leave instruction manual with owner after installation.
2. Installer must have owner fill out and mail warranty card supplied with unvented room heater.
3. Installer should show owner how to start and operate unvented
room heater.
Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of an
unvented room heater.
This appliance may be installed in an aftermarket* permanently
located, manufactured (mobile) home, where not prohibited by
state or local codes.
*Aftermarket: Completion of sale, not for purpose of resale, from
the manufacturer.
This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other
gases.
General Information
This BF-10, BF-20 and BF-30 are design certified in accordance with
American National Standards Institute Z21.11.2 by the Canadian
Standards Association as an Unvented Room Heater and should
be installed according to these instructions.
Any alteration of the original design, installed other than as shown
in these instructions or use with a type of gas not shown on the
rating plate is the responsibility of the person and company mak
ing the change.
WARNING: This appliance is equipped for (natural gas or
propane) gas. Field conversion is not permitted.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equip
ment or accessories and repair and servicing of equipment shall
be performed only by a qualified agency. The term "qualified
agency" means any individual, firm, corporation, or company that
either in person or through a representative is engaged in and is
responsible for (a) the installation, testing, or replacement of gas
piping or (b) the connection, installation, testing, repair, or servic
ing of equipment; that is experienced in such work; that is familiar
with all precautions required, and that has complied with all the
requirements of the authority having jurisdiction.
State of Massachusetts: The installation must be made by a
licensed plumber or gas fitter in the Commonwealth of Mas
sachusetts.
Sellers of unvented propane or natural gas-fired supplemental
room heaters shall provide to each purchaser a copy of 527
CMR 30 upon sale of the unit.
In the State of Massachusetts, unvented propane and natural
gas-fired space heaters shall be prohibited in bedrooms and
bathrooms.
The installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI Z223.1/
NFPA54.*
*Available from the American National Standards Institute, Inc., 11 West 42nd
St., New York, N.Y. 10036.
High Altitudes
For altitudes/elevations above 2,000 feet (610m), ratings should be
reduced at the rate of 4 percent for each 1,000 (305m) feet above
sea level. Contact the manufacturer or your gas company before
changing spud/orifice size.
Well Head Gas Installations
Some natural gas utilities use "well head" gas. This may affect
the Btu output of the unit. Contact the gas company for the heat
ing value. Contact the manufacturer or your gas company before
changing spud/orifice size.
-
-
-
-
SPECIFICATIONS
Specifications
Model BF-10 BF-20 BF-30
Input Btu/HR (KW/H)(LP)
Input Btu/HR (KW/H)(NAT)
Height 22" (559mm) 22" (559mm) 22" (559mm)
Width 18" (457mm) 18" (457mm) 24 1/8" (536mm)
Depth 6 1/2" (165mm) 6 1/2" (165mm) 6 1/2" (165mm)
Gas Inlet 3/8" (10mm) 3/8" (10mm) 3/8" (10mm)
Accessories
Blower SRB-18T SRB-18T SRB-30T
Floor Stand SRS-18* SRS-18 SRS-320
*SRS-18 floor stand can not be used in a bedroom installation.
BF-10 must be wall mounted in a bedroom installation.
The bedroom must be an unconfined space. ANSI Z223.1/NFPA 54 defines an unconfined space as "a space whose volume is not less
than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space."
16943-5-0806 Page 5
10,000 (2.9)
10,000 (2.9)
20,000 (5.8)
18,000 (5.3)
30,000 (8.8)
30,000 (8.8)
Page 6
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An unvented room
heater produces approximately one (1) ounce (30ml) of water for
every 1,000 Btu (.3KW's) of gas input per hour.
Unvented room heaters must be used as supplemental heat (a
room) rather than a primary heat source (an entire house). In most
supplemental heat applications, the water vapor does not create a
problem. In most applications, the water vapor enhances the low
humidity atmosphere experienced during cold weather.
The following steps will help insure that water vapor does not
become a problem.
1. Be sure the heater is sized properly for the application, including
ample combustion air and circulation air.
2. If high humidity is experienced, a dehumidifier may be used to
help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source
(an entire house).
PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR
This heater shall not be installed in a confined space or unusually
tight construction unless provisions are provided for adequate
combustion and ventilation air.
The National Fuel Gas Code, ANSI Z223.1 defines a confined space
as a space whose volume is less than 50 cubic feet per 1,000 Btu per
hour (4.8m
installed in that space and an unconfined space as a space whose
volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8m3
per kw) of the aggregate input rating of all appliances installed in
that space. Rooms communicating directly with the space in which
the appliances are installed, through openings not furnished with
doors, are considered a part of the unconfined space.
The following example is for determining the volume of a typical
area in which the BF-20 may be located and for determining if this
area fits the definition of an unconfined space.
The input of the BF-20 is 20,000 Btu per hour. Based on the 50
cubic feet per 1,000 Btu per hour formula, the minimum area that
is an unconfined space for installation of the BF-20 is 1,000 cubic
feet, 50 cubic feet x 20 = 1,000 cubic feet. To determine the cubic
feet of the area in which the BF-20 is to be installed, measure the
length, width and height of the area. Example: The area measures
16 feet in length, 8 feet in width and 8 feet in height, the area is
1,024 cubic feet. The BF-20 can be installed in this unconfined
space with no requirement to provide additional combustion and
ventilation air.
3
per kw) of the aggregate input rating of all appliances
Warning: If the area in which the heater may be operated is smaller
than that defined as an unconfined space or if the building is of
unusually tight construction, provide adequate combustion and
ventilation air by one of the methods described in the National Fuel
Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough
fresh air for combustion and ventilation. However, in buildings
of unusually tight construction, you must provide additional fresh
air.
Unusually tight construction is defined as construction where:
a. Walls and ceilings exposed to the outside atmosphere have
a continuous water vapor retarder with a rating of one perm
or less with openings gasketed or sealed, and
b. Weatherstripping has been added on openable windows and
doors, and
c. Caulking or sealants are applied to areas such as joints
around window and door frames, between sole plates and
floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical, and gas lines, and at
other openings.
If the heater is installed in a building of unusually tight construction,
adequate air for combustion, ventilation and dilution of flue gases
shall be provided in accordance with ANSI Z223.1/NFPA54.
Page 6 16943-5-0806
Page 7
VIEW FROM TOP OF HEATER
1 1
1/16” (43mm)
TO
WALL
3 9/16”
(90mm)
GAS INLET
IN BOTTOM
OF HEATER
GAS SUPPLY
The gas line can be routed either through the floor or wall. The gas line
opening should be made at this time. Location of the opening will be
determined by the position of floor joists and the valve and union used
for servicing.
Gas Supply
Check all local codes for requirements, especially for the size and type of
gas supply line required.
Recommended Gas Pipe Diameter
Pipe Length Schedule 40 Pipe
Inside Diameter
Tubing, Type L
Outside Diameter
Nat. L.P. Nat. L.P.
0-10 feet
0-3 meters
10-40 feet
4-12 meters
40-100 feet
13-30 meters
100-150 feet
31-46 meters
Note: Never use plastic pipe. Check to confirm whether your local codes
allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is always
best to consult your local authority and installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate, contact
your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant to the
action of liquefied petroleum gases. The gas lines must be checked for
leaks by the installer. This should be done with a soap solution watching
for bubbles on all exposed connections, and if unexposed, a pressure test
should be made.
Never use an exposed flame to check for leaks. Appliance must be
disconnected from piping at inlet of control valve and pipe capped
or plugged for pressure test. Never pressure test with appliance con
nected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas line
upstream of the gas control to aid in servicing. It is required by the Na
tional Fuel Gas Code that a drip line be installed near the gas inlet. This
1/2”
12.7mm
1/2”
12.7mm
1/2”
12.7mm
3/4”
19mm
3/8”
9.5mm
1/2”
12.7mm
1/2”
12.7mm
1/2”
12.7mm
Figure 1
1/2”
12.7mm
5/8”
15.9mm
3/4”
19mm
7/8”
22.2mm
3/8”
9.5mm
1/2”
12.7mm
1/2”
12.7mm
3/4”
19mm
should consist of a vertical length of pipe tee connected into the gas line
that is capped on the bottom in which condensation and foreign particles
may collect.
Figure 2
Method of Installing a Tee Fitting Sediment Trap (Figure 2)
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing and
Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority having
jurisdiction. The state of Massachusetts requires that a flexible appliance
connector cannot exceed three feet in length.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.
plugged tapping, accessible for test gauge connection, must be placed
immediately upstream of the gas supply connection to the appliance.
2. The appliance and its appliance main gas valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping system by
closing its equipment shutoff valve during any pressure testing of the
gas supply piping system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
Attention! If one of the above procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result
in a hazardous condition.
Checking Manifold Pressure
Natural gas will have a manifold pressure of approximately 3.5" w.c.
(.87kPa) at the pressure regulator outlet with the inlet pressure to the pres
sure regulator from a minimum of 5.0" w.c. (1.245kPa) for the purpose of
input adjustment to a maximum of 10.5" w.c. (2.615kPa). Propane/LP gas
will have a manifold pressure approximately 10.0" w.c. (2.49kPa) at the
pressure regulator outlet with the inlet pressure to the pressure regulator
from a minimum of 11.0" w.c. (2.739kPa) for the purpose of input adjustment to a maximum of 13.0" w.c. (3.237kPa).
A test gage connection is located downstream of the gas appliance pressure
regulator for measuring gas pressure. The connection is a 1/8 inch (3mm)
N.P.T. plugged tapping.
-
-
-
16943-5-0806 Page 7
Page 8
CLEARANCES
When facing the front of the appliance the following minimum clearances to combustible construction must be maintained.
Do not install in alcove or closet.
BF-10/BF-20 BF-30
Left side 5" (127mm) 8" (203mm)
Right side 5" (127mm) 8" (203mm)
Rear wall 0" (0mm) 0" (0mm)
Ceiling 36" (914mm) 36" (914mm)
Minimum vertical clearance from a projections above
the appliance (shelves, window sills, etc.)
Floor (top surface of carpeting, tile, etc.) 2" (51mm) 2" (51mm)
Provide adequate clearances around air openings.
Adequate accessibility clearances for purposes of servicing and proper operation must be provided.
36" (914mm) 36" (914mm)
BF-10 and BF-20
Figure 3
OPTIONAL FLOOR STAND INSTALLATION
SRS-18* and SRS-30 Floor Stand Installation
1. Align clearance holes on floor stand with screw holes on
bottom of heater, as shown in Figure 5.
2. Attach floor stand to heater with (4) screws provided with
floor stand.
3. Connect the gas line.
* SRS-18 floor stand can not be used in a bedroom
installation.
BF-10 must be wall mounted in a bedroom installation.
Installation on Rugs and Tile
If this appliance is installed directly on carpeting, tile or other
combustible material, other than wood flooring, the appliance shall
be installed on a metal or wood panel extending the full width and
depth of the appliance.
Attention: Optional SRS-18 and SRS-30 Floor Stand meets
requirement.
The base referred to in this section does not mean the fire-proof
base as used on wood stoves. The protection is for rugs that are
extremely thick and light colored tile.
BF-30
Figure 4
Figure 5
Page 8 16943-5-0806
Page 9
OUTLINE OF
OUTER CASING
MOUNTING HOLE LOCATIONS
VIEWED FROM FRONT OF HEATER
FLOOR
2” (51mm) MIN.
2 1/32” (52mm)
4 1/32”
(102mm) MIN.
18 7/8”
(479mm)
1 3/32”
(28mm)
24 1/8” (613mm)
20 1/8” (511mm)
2”
(51mm)
2”
(51mm)
22”
(559mm)
18” (457mm)
14” (356mm)
2”
(51mm)
2”
(51mm)
1 3/32”
(28mm)
18 7/8”
(479mm)
OUTLINE OF
OUTER CASING
4 1/32”
(102mm) MIN.
2 1/32” (52mm)
MOUNTING HOLE LOCATIONS
VIEWED FROM FRONT OF HEATER
FLOOR
2” (51mm) MIN.
22
”
(559mm)
WALL MOUNT INSTALLATION
Refer to Figures 6 and 7 for measurements in order to locate (4) mounting holes on wall. Figures 6 and 7 are the front views of the
heater.
1. Remove lower louver from casing assembly (2 screws).
2. Remove reflector from casing assembly (2 screws).
3. Remove upper louver from casing assembly (2 screws).
On Solid Wall
1. After locating mounting holes, attach (4) #10 x 1" (25mm) screws provided into the wall. Do not completely tighten screwheads
to the wall, leave a 1/8" (3mm) gap between screwheads and wall.
2. Mount heater onto the (4) screwheads and complete tightening screwheads into the wall.
Attention! Use the following steps to properly align the upper louver and the reflector with the heat shield.
a. When replacing upper louver, be sure the bottom lip of upper louver goes behind the heat shield.
b. When replacing reflector, be sure the top lip of reflector goes in front of the heat shield.
3. Connect the gas line.
BF-10 and BF-20
Figure 6
On Sheet Rock Wall
1. After locating mounting holes, drill (4) 5/16" (8mm) diameter
2. Insert (4) plastic expansion anchors provided into the
3. Tighten (4) #10 x 1" (25mm) screws provided into the plastic
holes into the wall.
holes.
expansion anchors. Do not completely tighten screwheads
to the plastic expansion anchors, leave a 1/8" (3mm) gap
between screwheads and plastic expansion anchors.
4. Mount heater onto the (4) screwheads and complete tightening
the screwheads to the plastic expansion anchors.
Attention! Use the following steps to properly align the upper
louver and the reflector with the heat shield.
a. When replacing upper louver, be sure the bottom lip of
upper louver goes behind the heat shield.
b. When replacing reflector, be sure the top lip of reflector
goes in front of the heat shield.
5. Connect the gas line.
16943-5-0806 Page 9
BF-30
Figure 7
Figure 8
Page 10
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result caus-
ing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set thermostat (gas control knob) to lowest setting.
3. Turn off all electric power to the appliance (if applicable).
4. Push in gas control knob slightly and turn clockwise
to "OFF". Do not force.
5. Wait ten (10) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow
"B" in the safety information above. If you don't smell gas,
go to the next step.
6. Find pilot - the pilot is
attached at the bottom of
the burner assembly .
7. Turn gas control knob
counterclockwise
8. Push in gas control knob all the way and hold in. Repeatedly
push the piezo ignitor button until pilot is lit (or use a match
to light pilot). Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release knob and it will
to "PILOT."
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it; call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
pop back up. Pilot should remain lit. If it goes out, repeat
steps 4 through 8.
• If knob does not pop up when released, stop and im
mediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician
or gas supplier.
9. Attention! Gas control has an INTERLOCK latching device.
When the pilot is initially lit and the safety magnet is ener
gized (pilot stays "ON") the INTERLOCK latching device
becomes operative. If the gas control is turned to the "OFF"
position or gas flow to the appliance is shut off, the pilot
cannot be relighted until the safety magnet is de-energized
(approximately 60 seconds). There will be an audible "click"
when the safety magnet in the gas control is de-energized.
Pilot can now be relighted. Repeat steps 4 through 8.
10. Turn gas control knob counterclockwise
to "HI".
11. Turn on all electric power to appliance (if applicable).
12. Set thermostat (gas control knob) to desired setting from "HI"
to "LO".
-
-
TO TURN OFF GAS TO APPLIANCE
1. Set thermostat (gas control knob) to lowest setting.
2. Turn off all electric power to appliance if service is to be
performed (if applicable).
Page 10 16943-5-0806
3. Push in gas control knob slightly and turn clockwise
to "OFF". Do not force.
Page 11
MAIN BURNER FLAME CHARACTERISTICS
Piezo Pilot Ignitor Instructions
Depressing the ignitor button completely causes a spark to occur
at the pilot.
To light the pilot, it is important that the electrode be 1/8" (3mm)
from the pilot. The spark must occur at the point the pilot flame
hits the thermocouple.
On a new installation with air in the gas line, it is suggested that a
match be used. The match will light the pilot faster than the piezo
under this condition.
There will be a short blue inner flame with a much larger, lighter
blue, secondary flame. The burner flame may have a small yellow
tip when hot. Dust in the combustion air will produce an orange or
red flame. Do not mistake the orange or red flame for an improper
yellow flame. Clean main burner by applying compressed air into
ports and throat of main burner.
Figure 9
Attention: BF-10, Natural or Propane gas has a front and rear air
shutter.
BF-20, Propane gas only has a front air shutter.
BF-30, Propane gas only has a front air shutter.
Air Shutter Adjustment (Figure 10)
The air shutter on main burner is factory set at a 3/32" opening. If
yellow flames occur on main burner loosen 1/4" screw on air shutter
in order to increase air shutter opening. The slot on air shutter allows
the air opening to be increased or decreased. Tighten 1/4" screw on
air shutter after air shutter adjustment has been completed.
Figure 10
Cleaning Main Burner Orifice and Main Burner
1. Turn OFF gas supply to the heater.
2. Turn OFF electric supply to the heater if optional blower,
SRB-18T or SRB-30T is installed in heater.
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Inspect interior of casing assembly for accumulation of dust,
lint or spider webs. If necessary, clean interior of casing
assembly with a vacuum cleaner or apply air pressure. Do
not damage any components within casing assembly when
you are cleaning.
6. Remove main burner orifice from orifice holder.
7. Apply air pressure through main burner orifice and orifice
holder to remove dust, lint or spider webs.
8. Apply air pressure into main burner to remove dust, lint or
spider webs.
9. As parts are being replaced in reverse order, check for gas
leaks at all gas connections before lower louver is replaced
onto casing assembly.
16943-5-0806 Page 11
Page 12
PILOT FLAME CHARACTERISTICS
The correct flame will be blue and will extend beyond the thermocouple. The flame will surround the thermocouple just below the
tip. A slight yellow flame may occur where the pilot flame and
main burner flame meet.
Figure 11
Oxygen Depletion Sensor Pilot (Figure 12)
When the pilot has a large yellow tip flame, clean the Oxygen
Depletion Sensor as follows:
1. Remove pilot from main burner assembly, see "Appliance
Maintenance", Page 13.
2. Apply air pressure through the holes in the pilot indicated by
the arrows in Figure 12. This will blow out foreign materials
such as dust, lint and spider webs.
Figure 12
Warning:
Never use needles, wires, or similar cylindrical objects to clean
the pilot to avoid damaging the calibrated ruby that controls
the gas flow.
THERMOSTAT OPERATION
To ignite main burner, rotate gas control knob counterclockwise
toward HI setting. To shut down main burner, rotate gas control
knob clockwise toward LO setting.
BF-10
The gas control has an input of 10,000 Btu/HR (2.9 KW/H).
The hydraulic thermostat bulb is located at the casing assembly
bottom.
BF-20
The gas control modulates from a minimum input of 8,500 Btu/HR
(2.5 KW/H) (LO setting) to a maximum input of 20,000 Btu/HR
(5.9 KW/H) for LP gas (HI setting) or 18,000 Btu/HR (5.3 KW/H)
for Natural Gas (HI setting). The hydraulic thermostat bulb which
is located at the casing assembly bottom adjusts the main burner
flame between minimum input and maximum input.
BF-30
The gas control modulates from a minimum input of 8,500 Btu/HR
(2.5 KW/H) (LO setting) to a maximum input of 30,000 Btu/HR
(8.8 KW/H) (HI setting). The hydraulic thermostat bulb which is
located at the casing assembly bottom adjusts the main burner flame
between minimum input and maximum input.
The LO and HI setting has temperature range of approximately 55°F
(12.78°C) to 90°F (32.22°C) , respectively. This is the temperature at
the hydraulic thermostat bulb not the room temperature. The owner
is advised to determine the particular heat setting that is desired for
comfort, as heating requirements are different for every owner.
Attention: If the owner does not want the main burner to ignite
and turns the gas control knob to the Lo setting, the main burner
will still ignite if the temperature at the hydraulic thermostat bulb
drops to 55°F (12.78°C).
If no heat is desired, turn the gas control knob to the PILOT
position.
Note: When the hydraulic thermostat bulb is "satisfied" the main
burner flame will shut "
"ON".
Page 12 16943-5-0806
OFF" with the pilot flame remaining
Page 13
APPLIANCE MAINTENANCE
Glass Removal, Cleaning and Glass Replacement
1. Remove chrome grill from reflector.
2. Slide glass upward to remove glass from chrome grill.
3. Clean glass with a non-abrasive household glass cleaner and
warm water. Gas fireplace glass cleaner can also be used.
4. Align glass with rails on chrome grill and slide glass downward
into chrome grill.
5. Attach chrome grill onto reflector.
Warning: Do not operate unvented room heater without glass/
chrome grill attached to reflector.
To Remove Pilot From Main Burner Assembly
1. Turn OFF gas supply to the heater.
2. Turn OFF electrical supply to the heater if optional blower,
SRB-18T or SRB-30T is installed in heater.
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Disconnect pilot tubing from pilot (see Figure 12, Page 12).
Grasp nut A with a wrench when removing nut B with a second
wrench.
6. Remove pilot from pilot bracket (2 nuts).
7. As parts are being replaced in reverse order, check for gas
leaks at all gas connections before lower louver is replaced
onto casing assembly.
To Remove Main Burner Orifice From
Main Burner Assembly
1. Turn off gas supply to the heater.
2. Turn off electrical supply to the heater if optional blower,
SRB-18T or SRB-30T is installed in heater.
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Disconnect supply tubing from orifice holder.
6. Remove orifice holder from venturi of main burner assem-
bly.
7. Remove main burner orifice from orifice holder.
8. As parts are being replaced in reverse order, check for gas
leaks at all gas connections before lower louver is replaced
onto casing assembly.
To Remove Gas Valve From Casing Assembly
1. Turn
2. Turn OFF electrical supply to the heater if optional blower,
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Remove upper louver from casing assembly (2 screws).
6. If installed, remove optional blower assembly (4 screws).
7. Disconnect inlet supply tubing, outlet supply tubing, pilot
8. If heater is attached to wall, disconnect gas supply line from
9. Remove heater from wall.
10. Remove gas valve bracket from casing assembly (4 screws to
11. Remove hydraulic thermostat bulb from thermostat bulb clip
12. Remove gas valve from gas valve bracket.
13. As parts are being replaced in reverse order, check for gas leaks
To Remove Main Burner From Casing Assembly
1. Turn
2. Turn OFF electrical supply to the heater if optional blower,
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Disconnect supply tubing from orifice holder.
6. Remove main burner assembly from casing assembly (2
7. Remove air shutter(s) from main burner. BF-10 Natural and
8. As parts are being replaced in reverse order, check for gas
OFF gas supply to the heater.
SRB-18T or SRB-30T is installed in heater.
supply tubing and thermocouple lead from gas valve.
inlet regulator.
be removed are located on casing assembly back).
located at casing assembly bottom.
at all gas connections before upper louver, reflector and lower
louver are replaced onto casing assembly.
OFF gas supply to the heater.
SRB-18T or SRB-30T is installed in heater.
screws).
LP has two (2) air shutters, BF-20 LP has one (1) air shutter
and BF-30 LP has one (1) air shutter. Attach air shutter(s) to
new main burner assembly.
leaks at all gas connections before lower louver is replaced
onto casing assembly.
16943-5-0806 Page 13
Page 14
TROUBLESHOOTING
SYMPTOMS - POSSIBLE CAUSES AND CORRECTIONS
1. Spark electrode does not produce spark.
a. Spark electrode broken - replace.
b. Ignitor wire may not be attached to spark electrode -
attach.
c. Ignitor wire damaged - replace.
d. Piezo ignitor defective - replace.
2. Spark electrode produces spark but pilot does not light.
a. No gas to heater - turn on gas.
b. PILOT position not properly aligned - turn gas control knob
to PILOT position and depress.
c. Pilot is blocked from spider web or dirt - clean pilot, see
Figure 12, Page 12.
3. Pilot flame does not stay "ON" when control knob is
released.
a. Control knob in PILOT position not completely depressed
or held in long enough.
b. INTERLOCK latching device is operative - see "Lighting
Instructions," Page 10, Step 9.
c. Thermocouple lead not tightened into gas control - tighten
thermocouple lead.
d. Pilot flame not surrounding thermocouple - clean pilot, see
Figure 12, Page 12.
e. Inlet gas pressure too low, contact gas supplier.
f. Thermocouple defective - replace pilot.
g. Gas control defective - replace.
4. Main burner does not ignite.
a. Main burner orifice is blocked - clean, see "Main Burner
Flame Characteristics," Page 11.
b. Inlet gas pressure too low, contact gas supplier.
5. Heater keeps shutting "OFF" during normal operation.
a. Pilot is blocked - clean pilot, see Figure 12, Page 12.
b. Inlet gas pressure too low, contact gas supplier
Page 14 16943-5-0806
Page 15
PARTS LIST
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
INDEX PART
NO. NO. DESCRIPTION
INDEX PART
NO. NO. DESCRIPTION
01 13347 CASING SIDE ASSEMBLY - LEFT (BF-10 )
01 13348 CASING SIDE ASSEMBLY - LEFT
(BF-20 BF-30)
02 SR-090 CASING BACK (BF-10 BF-20)
02 SR-041 CASING BACK (BF-30)
03 R-2313 PIEZO IGNITOR
04 11231 FAN CONTROL BRACKET (BF-10)
05 SR-008 CASING SIDE ASSEMBLY - RIGHT
06 R-1992 BULB CLIP
07 SR-076 CASING LOUVER-TOP (BF-10 BF-20)
07 SR-017 CASING LOUVER-TOP (BF-30)
08 SR-077 HEAT SHIELD (BF-10 BF-20)
08 SR-018 HEAT SHIELD (BF-30)
09 SR-075 REFLECTOR SHIELD REAR (BF-10 BF-20)
09 SR-016 REFLECTOR SHIELD REAR (BF-30)
10 10420 REAR SHIELD (BF-10 BF-20)
10 10420 REAR SHIELD (BF-30)
11 10417 REFLECTOR ASSEMBLY (BF-10 BF-20)
11 10475 REFLECTOR ASSEMBLY (BF-30)
12 10467 CASING LOUVER-BOTTOM ASSEMBLY
(BF-10 BF-20)
12 10469 CASING LOUVER-BOTTOM ASSEMBLY (BF-30)
13 R-4979 CHROME GRILL (BF-10 BF-20)
13 R-4980 CHROME GRILL (BF-30)
14 R-4993 GLASS (BF-10 BF-20)
14 R-4994 GLASS (BF-30)
15 R-2784 INLET REGULATOR - NAT
15 R-2480 INLET REGULATOR - LPG
16 10753 INLET REGULATOR BRACKET
17 12442 TUBING - GAS VALVE TO BURNER
(BF-10 BF-20)
17 12443 TUBING - GAS VALVE TO BURNER (BF-30)
18 12437 TUBING - INLET REGULATOR TO GAS VALVE
19 R-6563 GAS VALVE (NAT & LPG)
20 SR-113 VALVE BRACKET
21 10460 BURNER BRACKET - LEFT
22 10422 BURNER (BF-10 BF-20)
22 10481 BURNER (BF-30)
23 10424 AIR SHUTTER (BF-10 ONLY)
24 10461 BURNER BRACKET - RIGHT
25 P-214 MAIN BURNER ORIFICE (BF-10 NAT)
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
25 P-193 MAIN BURNER ORIFICE (BF-10 LPG)
25 P-252 MAIN BURNER ORIFICE (BF-20 NAT)
25 P-182 MAIN BURNER ORIFICE (BF-20 LPG)
25 P-211 MAIN BURNER ORIFICE (BF-30 NAT)
25 P-185 MAIN BURNER ORIFICE (BF-30 LPG)
26 P-212 ORIFICE HOLDER
27 10424 AIR SHUTTER (BF-10 NAT & LPG)
(BF-20 & BF-30 LPG ONLY)
28 10539 TUBING - GAS VALVE TO PILOT
(BF-10 BF-20)
28 10540 TUBING - GAS VALVE TO PILOT (BF-30)
29 R-6306 PILOT ASSEMBLY (NAT ONLY) (INCLUDES
30 & 31)
29 R-6308 PILOT ASSEMBLY (LPG ONLY)
(INCLUDES 30 & 31)
30 R-6310 PILOT THERMOCOUPLE
31 R-6309 SPARK IGNITOR
32 R-2390 IGNITOR WIRE
33 SR-120 OPTIONAL SRS-18 FLOOR STAND KIT
(BF-10 BF-20)
33 SR-115 OPTIONAL SRS-30 FLOOR STAND KIT
(BF-30)
34 SR-122 OPTIONAL SRB-18T BLOWER KIT(BF-10 BF-
20) (INCLUDES 34 THROUGH 41)
34 SR-116 OPTIONAL SRB-30T BLOWER KIT (BF-30)
(INCLUDES 34 THROUGH 41)
35 R-1454 BRASS BUSHING (4 REQUIRED)
36 R-1499 RUBBER GROMMET (4 REQUIRED)
37 SR-196 BLOWER PAN (BF-10 BF-20)
37 SR-198 BLOWER PAN (BF-30)
38 VF-068 CORD SET ASSEMBLY
39 R-1468 BUSHING - HEYCO #SR5KN4
40 R-2395 WIRE ASSEMBLY
41 R-2503 FAN CONTROL
42 R-2396 BLOWER (INCLUDES MOTOR, FAN, AND
FAN HOUSING)
NOT SHOWN SR-219 BLOWER HARDWARE PACKAGE
NOT SHOWN SR-216 HARDWARE PACKAGE
NOT SHOWN R-1976 MIN. RATE SCREW NAT 1.60
NOT SHOWN R-1977 MIN. RATE SCREW LP 1.00
HOW TO ORDER REPAIR PARTS
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor.
Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then
determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give
all this information.
Unvented Heater Model Number Part Description
Unvented Heater Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
16943-5-0806 Page 15
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62220-2623
Page 16
PARTS VIEW
Page 16 16943-5-0806
Page 17
HEAT SHIELD
FA
N
CONTROL
BRACKET
(BF-10
ONL
Y)
FA
N
CONTROL
GROUN
D W
IR
E S
CRE
W
CORD
SET HOLE
IN
CASING BAC
K
REFLECTOR AND LOUVERS ARE
REMOVED FROM CASING ASSEMBL
Y
OPTIONAL BLOWER INSTALLATION INSTRUCTIONS
SRB-18T and SRB-30T
for Unvented Room Heaters BF-10, BF-20 and BF-30
INSTALLING OPTIONAL BLOWER SRB-18T OR SRB-30T
If heater is installed onto the wall, in order to install the optional blower,
the heater must be removed from the wall. If heater is installed on SRS-18
or SRS-30 optional floor stand there is adequate access area available to
install the optional blower.
1. Turn "OFF" gas supply to the heater.
2. Remove lower louver from casing assembly (2 screws).
3. Remove reflector from casing assembly (2 screws).
4. Remove upper louver from casing assembly (2 screws).
5. Insert the fan control wires and the upper portion of the fan control
through the 3/4" (19mm) diameter hole on the bottom side of the
top heat shield. The fan control wires will enter into the top portion
of the heater and the fan control disc will be facing the main burner.
Attach fan control to the bottom side of the top heat shield with (2)
screws provided with the optional blower.
6. Route cord set through 9/16" (14mm) diameter hole on casing
assembly back. Insert approximately 3" (76mm) of cord set into
casing assembly back.
7. When you are facing the front of the heater, position the optional
blower assembly onto the top heat shield of the heater. The motor
wire harness should be facing into the top, right portion of the
heater.
8. Attach (1) pin terminal from black (hot) wire, smooth insulation on
cord set to (1) socket terminal on fan control wire harness.
9. Attach (1) pin terminal from black (neutral) wire, ribbed insulation
on cord set to (1) socket terminal from white (neutral) wire on motor
wire harness.
10. Attach (1) pin terminal on fan control wire harness to (1) socket
terminal from black (hot) wire on motor wire harness.
11. Attach the green ground wire from the motor wire harness and the
green ground wire from the cord set to the bottom right side of the
blower housing with (1) screw provided with the optional blower.
12. With the heater standing upright, position the air discharge opening
of the blower housing downward. Place the bottom flange of the
blower housing over the top edge of the top heat shield. Insert the
blower housing into the top portion of the heater by pivoting the
blower housing upward 90°. Attach the blower housing to the casing
assembly with (4) screws provided with the optional blower.
13. Grasp cord set at casing assembly back and pull excess cord set
through casing assembly back. Secure cord set in casing assembly
back with the strain relief provided with the optional blower.
14. Installati on of option al blower SR B-18T or SRB -30 T is
completed.
15. If heater was removed from the wall, in order to install SRB-18T or
SRB-30T optional blower, check for gas leaks at all gas connections
before lower louver is replaced onto casing assembly.
Attention! After optional blower has been installed use the following steps
to properly align the upper louver and the reflector with the heat shield.
A. When replacing upper louver, be sure the bottom lip of upper louver
goes behind the heat shield.
B. When replacing reflector, be sure the top lip of reflector goes in front
of the heat shield.
Excessive Blower Wheel Noise
ATTENTION! If your blower assembly develops a squeal, hum or grinding
noise, it indicates dirt or debris on shaft of blower wheel. Use the following
steps to clean shaft of blower wheel.
1. Remove red rubber grommet with brass bushing or black rubber
grommet with brass bushing from end of blower wheel shaft opposite
motor.
2. Clean blower wheel shaft with cotton cloth.
3. Place 1 or 2 drops of all purpose oil on END of blower wheel
shaft.
4. Replace red rubber grommet with brass bushing or black rubber
grommet with brass bushing onto end of blower wheel shaft. Attention:
The red rubber grommet with brass bushing or the black rubber
grommet with brass bushing must "snap-back" into position.
5. Cleaning of blower wheel shaft is completed.
16943-5-0806 Page 17
Page 18
OPTIONAL BLOWER INSTALLATION INSTRUCTIONS (continued)
Wiring
The appliance, when installed, must be electrically grounded in accordance
with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, if an external electrical source is utilized. This
appliance is equipped with a three-prong [grounding] plug for your protec
tion against shock hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or remove the grounding
prong from this plug. For an ungrounded receptacle, an adapter, which has
two prongs and a wire for grounding, can be purchased, plugged into the
ungrounded receptacle and its wire connected to the receptacle mounting
screw. With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded.
CAUTION: Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
-
Blower Motor
The blower motor does not have oiling holes. Do not attempt to oil the
blower motor.
Blower Wheel
The blower wheel will collect lint and could require periodic cleaning.
If the air output decreases or the noise level increases, it indicates a dirty
blower wheel.
To clean blower wheel:
1. Turn OFF gas supply to the heater.
2. Turn OFF electrical supply to the heater.
3. Remove lower louver from casing assembly (2 screws).
4. Remove reflector from casing assembly (2 screws).
5. Remove upper louver from casing assembly (2 screws).
6. Clean blower wheel with a vacuum cleaner.
7. As parts are being replaced in reverse order, check for gas leaks at
all gas connections before lower louver is replaced onto casing as
sembly.
WARNING:
Unplugging of blower accessory will not stop the heater from cycling.
To turn off gas to the unvented heater: Push in gas control knob
slightly and turn clockwise to "OFF." Do not force.
If any of the original wire as supplied with the appliance must be replaced,
it must be replaced with type 125°C wire or its equivalent.
. ...
-
PARTS LIST
INDEX PART
NO. NO. DESCRIPTION
1 R-2396 BLOWER (INCLUDES MOTOR, FAN, AND
FAN HOUSING)
2 R-2503 FAN CONTROL
3 R-2395 WIRE ASSEMBLY
4 R-1468 BUSHING - HEYCO #SR5KN4
5 VF-068 CORD SET ASSEMBLY
6 SR-196 BLOWER PAN (BF-10 BF-20)
6 SR-198 BLOWER PAN (BF-30)
7 R-1499 RUBBER GROMMET (4 REQUIRED)
8 R-1454 BRASS BUSHING (4 REQUIRED)
NOT SHOWN SR-219 BLOWER HARDWARE PACKAGE
Page 18 16943-5-0806
Page 19
SERVICE NOTES
16943-5-0806 Page 19
Page 20
Empire Comfort Systems, Inc.
918 Freeburg Ave. Belleville, IL 62220
PH: 618-233-7420 or 800-851-3153
FAX: 618-233-7097 or 800-443-8648
info@empirecomfort.com
www.empirecomfort.com
Page 20 16943-5-0806
Loading...