Page 1
3.28
(83.3)
2.75
(69.85)
.700 (17.78)
.770 (19.5)
PO BOX 4394
SANTA ROSA, CA
95402 USA
0230-0109rD
P (707) 525-9941
F (707) 575-7046
EMGPICKUPS.COM
S, SA, SLV
SV, SAV
POLES
EXPOSED
6/32 MOUNTING SCREWS
.412 (10.46) TYP
3.00
(76.2)
INSTALLATION INFORMATION
EMG MODELS: EMG-S, SA, SV, SAV, SLV
SPECIFICATIONS: MODEL:
S SA SV SAV SLV
Logo Color Silver Gold Gold Gold Gold
Magnet Type * C A A A A
Resonant Frequency (KHz) 4.05 3.70 2.41 4.41 3.33
Output Voltage (String) 1.00 1.00 1.00 1.00 1.00
Output Voltage (Strum) 3.00 3.00 3.00 3.00 3.00
Output Noise (60 Hz) -101 -101 -102 -101 -103
Output Impedance (Kohm) 10 10 10 10 10
Current @9V (Microamps) 80 80 80 80 80
Battery Life (Hours) 3000 3000 3000 3000 3000
Maximum Supply (Volts DC) 27 27 27 27 27
*Note: Magnet Type: A (Alnico) C (Ceramic)
Installation notes:
All EMG Pickups are compatible with each other. The connector system is an easy method of installation, avoiding the need to solder.
Older systems may need to be soldered, while the newer systems can be easily connected and modified. If you have an older EMG
Pickup you can install the new system along with it.
EMG accessories like the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System without the need for an extra battery.
Included with each pickup:
1 VOLUME CONTROL (25K)
1 TONE CONTROL (25K)
.235
(6)
ADJUSTMENT
SCREWS & SPRINGS
.490 (12.44)
PICKUP CABLE 15” (38cm)
.390
(10)
BATTERY
BUSS
.310
(8)
STEREO OUTPUT
JACK
2 PICKUP IN/ OUT
BATTERY BUSS
2 CONNECT CABLES 5.5” (14cm)
OUTPUT CABLE 6” (15cm)
BATTERY CABLE 7” (18cm)
B245
- 9V +
Warranty
All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.
© 2014 Copyright EMG INC. All Rights Reserved.
Page 2
Installation Instructions:
EMG Models: EMG-S, SA, SV, SAV, SLV
General Notes:
Every attempt has been made to make this a solderless installation.
There are some instances where this is not possible;
1) If your instrument uses the long panel output jack and you had passive pickups
you will need a new stereo output jack, the Switchcraft 152B is recommended.
Soldering to the new jack will be required, see diagram #4 below.
2) Some instruments may already have a battery holder installed and in that case
soldering may be required to the battery buss, see diagram #5 below.
3) Instruments with two pickups may need soldering to the selection
switch in some installations.
Diagram #1
Insert the plug onto the 3 pin header
of the pickup as shown above.
Note the orientation arrow.
If you are installing only one pickup use the instructions on this page.
If you are installing two pickups go to page 3 and begin there.
Installation (One Pickup Guitars):
1) Plug the pickup cable onto the EMG Pickup header as shown
in diagram #1 and route the cable to the control cavity.
If the cable is too long, wind up the excess and keep it
under the pickup if possible.
Master Volume control only
2) Refer to diagram #2. Plug both the Pickup cable and the output
cable onto the Volume control as shown, then go to step 4.
Master Volume and Tone control
3) Refer to diagram #3. Plug the Pickup cable onto the Volume
control as shown. Plug a coax cable from the Volume control
to the Tone control. Plug the output cable onto the tone
control as shown.
4) Connect the wires of the output cable to the output jack by
pushing the connectors on as shown.
WHITE wire to the TIP (T) contact,
BLACK wire to the SLEEVE (S) contact
BLACK Battery Negative wire to the RING (R) contact.
5) Using the battery buss, insert the RED wire of the pickup,
and the battery RED wire. Extra pins can be used for
EMG Accessories.
6) Put the battery in the insulating foam piece provided
and place it securely in the control cavity.
We suggest that you plug in the instrument and
test it before closing the control cavity.
FROM PICKUP
FROM PICKUP
Diagram #3
One Pickup
One Volume
One Tone
Diagram #2
One Pickup
One Volume
MASTER
VOLUME
- 9V +
VOLUME
B122rH
- 9V +
MASTER
VOLUME
VOLUME
B122rH
RED
RED
RED
RED
BATTERY
OUTPUT CABLE
BATTERY
BUSS
MASTER
TONE
B124rH
TONE
NEG (-)
BATTERY
BUSS
BATTERY
R
S
T
NEG (-)
R
S
Diagram #4
Soldering to the 152B Panel Jack:
If your instrument has a long Panel Jack like the one below
you will have to solder the output cable as shown.
Ground (Black) to the sleeve
Signal (White) to the Tip
Battery Negative (Black) to the Ring
- 9V +
RED to BATTERY BUSS
BATTERY
NEG (-)
RING
FROM TONE
SLEEVE
OR VOLUME
S Instructions Page 2
TIP
OUTPUT CABLE
Diagram #5
Soldering to the battery buss:
If your instrument has an older EMG Pickup you can solder the
pickup RED wire to the buss. Simply use some needle nose pliers,
pull out the V+ header and solder the RED Wire from the pickup(s)
to any of the pins and then re-insert the header into the housing.
1
2
Solder the RED wire from the Battery Holder and/or
pickups and re-insert the Header into the insulation cover
3
T
Page 3
Installation Instructions:
****Tips and Tricks**** Start your installation by:
1) Determine which type output jack your instrument has.
A Stereo 12B type is Included, but if you have a long panel jack
a SwitchCraft 152B Long Panel Jack will be required.
2) Remove the strings, remove any existing Pickups and controls
(remember the order and function of each control)
3) Determine a good spot for the Pickup Buss and make sure the
cable or wires from the selection switch will reach the Pickup Buss,
4) Install the EMG Volume and Tone Controls and tighten them in.
5) Then install the pickups keeping any excess cable under the pickup
rather than in the control cavity.
6) IMPORTANT: EMG Active pickups do not require a string ground wire!
DO NOT Reconnect the string ground, it is unnecessary.
EMG Models: EMG-S, SA, SV, SAV, SLV
Two Pickup Guitars with Selection switch:
Guitars with two pickups and a selection switch will use the EMG B245 Pickup Buss.
The Pickup Buss is a convenient way to wire your guitar without soldering.
There is a separate sheet attached to these instructions that describes the
Pickup Buss in detail.
In all installations it’s best to find a place to mount the Pickup Buss in the control
cavity before starting. Then, after the cables are routed use the velcro to mount it
securely.
2 Pickups / Toggle Select Switch / Master Volume and Tone
1) Install the Pickups and route the Pickup cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body.
Plug both Pickup cables onto the Pickup Buss (BLACK Shroud) as shown,
Refer to diagram #6a
Bridge Pickup to position 1
Neck Pickup to position 2.
3) Plug a coax cable from the Pickup Buss (position 3) to the Master Volume
control as shown in diagram #6b.
4) Plug a coax cable from the Master Volume to the Master Tone as shown.
5) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
6) Plug the output cable onto the Master Tone control and connect the output
wires to the output jack by pushing the connectors on as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
****Tips and Tricks**** Start your installation by:
1) Determine which type output jack your instrument has.
A Stereo 12B type is Included, but if you have a long panel jack
a SwitchCraft 152B Long Panel Jack will be required.
2) Remove the strings, remove any existing Pickups and controls
(remember the order and function of each control)
3) Determine a good spot for the Pickup Buss and make sure the
cable or wires from the selection switch will reach the Pickup Buss,
4) Install the EMG Volume and Tone Controls and tighten them in.
5) Then install the pickups keeping any excess cable under the pickup
rather than in the control cavity.
6) IMPORTANT: EMG Active pickups do not require a string ground wire!
DO NOT Reconnect the string ground, it is unnecessary.
7) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip.
Extra pins on the V+ Supply Buss are for EMG Accessories.
8) Put the battery in the insulating foam piece provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
Diagram #6a
TO SELECTION SWITCH
BRIDGE PICKUP INPUT
NECK PICKUP INPUT
OUTPUT
PLUG IN
LIKE THIS!
BRIDGE PICKUP
OUTPUT TO
MASTER VOLUME
Diagram #6b
2 Pickups
Toggle Style Select Switch
Master Volume & Master Tone
- 9V +
GROUND
NECK P/U
OUTPUT
RED
RED
BRIDGE P/U
BRIDGE PICKUP
NECK PICKUP
2 Pickups / Toggle Select Switch / 2 Volumes and Master Tone
Refer to Diagram #7 (Next Page)
1) Install the Pickups and route the Pickup cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body.
Plug both pickup cables onto the Volume controls as shown.
Plug a coax cable from the Bridge Volume control to the Pickup Buss (Position 1)
Plug a coax cable from the Neck Volume control to the Pickup Buss (Position 2)
3) Plug a coax cable from the Pickup Buss (position 3) to the Master Tone
control as shown.
4) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck Pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
RED
S Instructions Page 3
NECK PICKUP
BATTERY
NEG (-)
MASTER
VOLUME
B122rH
R
VOLUME
MASTER
TONE
B124rH
TONE
OUTPUT CABLE
5) Plug the output cable onto the Tone control and connect the wires to the
output jack by pushing the connectors on as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
6) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip. Extra pins are for EMG Accessories.
7) Put the battery in the insulating foam provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
S
T
Page 4
- 9V +
GROUND
NECK P/U
OUTPUT
BRIDGE P/U
Diagram #7
2 Pickups
Toggle Style Switch
Volume each Pickup (Volumes are independent)
Master Tone
2 Pickups / Toggle Select Switch / 2 Volumes and 2 Tones)
Refer to Diagram #8
1) Install the Pickups and route the cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body
Plug both Neck and Bridge pickup cables onto the Volume Controls as shown.
Plug a coax cable from the Bridge (BR) Volume control to the Pickup Buss
(Position 1).
Plug a coax cable from the Neck (NK) Volume control to the Pickup Buss
(Position 2).
3) Plug a coax cable from the Bridge (BR) Volume control to the Bridge (BR) Tone
control as shown.
4) Plug a coax cable from the Neck (NK) Volume control to the Neck (NK) Tone
control as shown.
5) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck Pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
NECK PICKUP
BRIDGE PICKUP
BATTERY
NEG (-)
MASTER
TONE
RED
RED
RED
B124rH
TONE
OUTPUT CABLE
NK VOLUME
B122rH
VOLUME
BR VOLUME
B122rH
VOLUME
6) Plug the output cable onto the Pickup Buss (Position 3) and push the
connectors onto the jack as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
7) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip. Extra pins are for EMG Accessories.
8) Put the battery in the foam insulator provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
Diagram #8
2 Pickups
2 Volume (either volume will act as a master)
2 Tone
Toggle Style Switch
R
S
T
Page 4
GROUND
NECK P/U
OUTPUT
BRIDGE P/U
- 9V +
FROM NECK PICKUP
FROM BRIDGE PICKUP
RED
RED
RED
BATTERY
NEG (-)
OUTPUT CABLE
B122rH
VOLUME
NK VOLUME
B122rH
VOLUME
BR VOLUME
R
S
T
B124rH
TONE
NK TONE
B124rH
TONE
BR TONE
Loading...