Page 1
INSTALLATION INFORMATION
EMG Model: EMG-KFK Set
Kerry King Set
SPECIFICATIONS:
Preferred Pickup Placement
Logo Color
Magnet Type
Resonant Frequency (KHz)
Output Voltage (String)
Output Voltage (Strum)
Output Noise@ 60Hz
Output Impedance (Kohm)
Current@ 9V (Microamps) (System)
Battery Life (Hours) (System)
Maximum Supply (Volts DC)
81
-
Silver Gold
2.2.00 2.45
2.0 2.1
91 -89
MODEL:
85
Bridge
C/S
4.5 4.5
10 10
160
1500
27
Note: Magnet Type: A (Alnico)
C/S (Ceramic/Steel)
IMPORTANT INSTALLATION NOTES:
1) Only one battery is required for the pickups,
and any active accessories such as the SPC,
RPC, EXG, AB, PA-2, and Pi-2.
2) Use an Alkaline or Lithium battery for longest life.
3) The controls included with EMG Systems are 25K
Ohm, Audio Taper. This value of control is required
for the system to work correctly.
4) When installing EMG Active Pickups, DO NOT connect
the bridge ground wire. This wire is usually soldered
to a volume or tone control casing and goes to the
bridge. This wire grounds the strings and uses them
and your body as a shield against hum and buzz. It
also creates a shock hazard. EMG Pickups are
MODEL:
PA2
Neck
Alnico
Input Impedance (Ohms)
Output Noise@ 60Hz
Output Noise(Spectral)
Output Impedance (Ohms)
Current@ 9V (Microamps)
Battery Life (Hours)
Maximum Supply (Volts DC)
shielded internally and DO NOT require string
grounding. This greatly reduces the possibility of
reverse polarity shock from microphones and other
equipment
5) EMG Active Pickups have very little magnetism
compared to passive pickups. We recommend
you adjust the pickups as close to the strings as
possible. Sustain and string movement will not be
inhibited by close adjustment.
6) If your installation is different from the diagrams in
these instructions or you need additional diagrams
visit our website: emgpickups.com for a complete
listing of available diagrams.
-130 dbV
500K
-91 dbV
2K
290
1725
27
Warranty:
All EMG Pickups and accessories are warranted for a period of two years. This warranty
does not cover failure due to improper installation, abuse or damage. If at any time a pickup
fails to work, return it postage prepaid with proof of purchase. Warranty replacement
products are covered by this same warranty. This warranty covers only those pickups and
accessories sold by authorized EMG Dealers. This warranty is not transferable.
© Copyright EMG Inc. 2007
Page 2
Installation Instructions:
EMG Model: PA-2
1) The PA-2 requires a 1/4 inch hole (6.2mm) and the
bushing length is 5/16 inches long (8mm). Optimum
control compartment body thickness is less than 1/4 inch.
2) The PA-2 features EMG’s 5 pin Quik-Connect system plug
for ease of installation and it allows you to exchange other
EMG Accessory Circuits in it’s place. The EMG 5 pin
connector always uses the following legend for hook-up.
Wire Legend:
Red Supply Voltage +9/+18/+27
Green Output of PA-2
Black Ground
Black Ground #2 for convenience
White Input to PA-2
3) Install the PA-2 in the guitar and then follow the diagram(s)
on this sheet that best fit your installation.
The diagrams shown are for EMG Active Pickups only.
All diagrams show the Red Wire coming from the pickups
connected to the battery. If you are installing EMG-HZ
Passive Pickups refer to those diagrams. The Red Wire of
the HZ Pickup is NOT for battery power, it is a coil wire.
White
Red
Green
Red
White
Green
Loading...