EMG BTC CONTROL Installation Information

PO BOX 4394

A ROSA, CA

SANT
95402 USA

0230-0206B

P [phone]
F [phone]
EMGPICKUPS.COM

Treble Control

Bass Control

INSTALLATION INFORMATION
EMG MODEL: BTC CONTROL

(ACTIVE / PASSIVE PICKUP INPUT)

SPECIFICATIONS

Input Impedance (Ohms) 1 MegOhm
Gain/Attenuation/ Frequency Bass Control +/-12db/20Hz
Gain/Attenuation/ Frequency Teble Control +/-12db/(Adjustable)
Input Referred Noise -120dbV
Output Impedance (Ohms) 2K
Recommended Supply Voltage 18 Volts
Current @ 9V/18V (Microamps) 600/740

High Frequency
Selection dip-switch

INCLUDED:

1 BTC Control
1 Set Concentric Knobs
1 Battery Clip with Buss Connector
1 Stereo Output Jack (Battery Switching)
4 Interconnect Cables (2 Red, 2 White)

Battery Life (Hours) 750
Maximum Supply (Volts DC) 27 Volts

General Operation

The BTC Control is a 2-band equalizer for Bass guitar. The BTC features single-pole filters for broadband equalization. Often the broader
single-pole filters are preferred for musical instruments because they are less selective, easier on the ear, and sound more “musical”. One of
the features of the BTC Control is a 2-position dip-switch that controls the slope of the high frequency response. By choosing one of the four
combinations the high frequency response can be tailored to your liking. The BTC Control has a high input impedance and can be used with active
or passive pickups. Bass and Treble controls are mounted on a concentric shaft and knobs are included.

Battery Power:

If you play the instrument very hard, and are boosting the bass or treble with the BTS, you should consider operating the instrument on +18
Volts (2 Batteries in series, see page 4). If you play mildly and use a minimum of boost the instrument should operate easily on a single 9-Volt
battery. Use an Alkaline or Lithium battery for the best battery life and always unplug your guitar when you’re not using it.

Dimensions:
BTC (Bass/Treble)
Equalizer

VOLTS +

OUTPUT

GROUND

GROUND

INPUT

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.

© 2010 Copyright EMG INC. All Rights Reserved.

1.813
(46)

1.000
(25.4)

.937
(24)

.538
(14)

.392
(10)

.875
(22.2)

.875
(22.2)

6 x 9mm
D Shaft

8 x 4mm

9 x 9mm
P .75

.077 x .077 Slot
(2mm)

Installation Instructions:
EMG Model: BTC Control

High Frequency Response Selection:

The BTC has the added feature of allowing you to choose from 4 different
high frequency response curves. This is a nice feature especially if you are
using the BTC with passive pickups. The following diagrams show the dip-switch
positions and the graphs show the resultant frequency response.
The BTC Control is an equalizer style control, offering both boost and cut
at the same frequency locations. The controls feature a center detent (notch)
that lets you know when no equalization is in effect.

ON/ON

10 dB/div

20Hz

BTC CONTROL (BASS BOOST & CUT RESPONSE)

1KHz

ON/OFF

10KHz

BTC CONTROL (TREBLE RESPONSE: ON/ON)

10 dB/div

20Hz

OFF/OFF

BTC CONTROL (TREBLE RESPONSE: 1 OFF/2 OFF)

10 dB/div

20Hz

10KHz1KHz

10KHz1KHz

The BTC Control is easily installed by using the connector cables supplied.
Diagram #1 shows the cables connected to the BTC Control. This 5-pin
layout is the same for all EMG Accessories, so they can be interchanged.

There are a variety of ways instruments can be wired. The examples shown
here are only a few. If your instrument has different wiring than shown here
go to our website: http://www.emgpickups.com for alternate diagrams.

BTC CONTROL (TREBLE RESPONSE: 1 ON/2 OFF)

OFF/ON

BTC CONTROL (TREBLE RESPONSE: 1 OFF/2 ON)

10 dB/div

20Hz

NOTE REVERSED
INPUT CONNECTOR

Diagram #1

10KHz1KHz20Hz

10KHz1KHz

Diagram #2 below shows the installation of a single Volume control along with
the BTC Control.

Diagram #2
Master Volume
BTC Control

- 9V +

VOLUME

BTC Control Page 2

BATTERY

BUSS

NOTE REVERSED
CONNECTOR!

BTC
CONTROL

OUTPUT CABLE

S

R

T

OUTPUT

RED TO 9V + BUSS

OUTPUT TO JACK

INPUT