Emerson WYATT CF530BS00, WYATT CF530WW00, WYATT CF530ORB00 Owner's Manual
Part No. F40BP74840000 Form No. BP7484
Revision: 131218 ETL Model No.: CF530
READ AND SAVE THESE INSTRUCTIONS
WYATT
™
48” Ceiling Fan Owner's Manual
CF530BS00 - Brushed Steel
CF530ORB00 - Oil Rubbed Bronze
CF530WW00 - Appliance White
Model Numbers
Net Weight: 16.2 Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., Eastern, Monday-Friday
1-800-654-3545
www.emersonfans.com
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 1
2
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2014” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
5. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall control/
switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To avoid fire, shock or injury, do not use an
Emerson or any other brand of control not specifically
approved for this fan.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful with the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
ETL Model No.: CF530
READ AND SAVE THESE INSTRUCTIONS
Table of Contents
Section Page
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . .3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . .4
3. How to Hang Your Ceiling Fan . . . . . . . . . . . . . .5-6
4. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . .7-9
5. Ceiling Fan Assembly . . . . . . . . . . . . . . . . . . .10-13
6. How to Wire Your Wall Control . . . . . . . . . . . .14-15
Section Page
7. Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . .16
8. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
9. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
10. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
11. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . .20
12. Instruction to the User . . . . . . . . . . . . . . . . . . . . .21
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . .23
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 2
1. Unpacking Instructions
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF530
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free for replacement parts:
1-800-654-3545
WARNING
!
1.1
Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration below.
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost.
If any parts are missing, call 1-800-654-3545
for replacement parts before proceeding.
PACKAGE CONTENTS
Part Description Quantity
A Ceiling Mounting Plate 1
B Fan Motor 1
C Fan Motor Housing 1
D Flywheel 1
E Light Kit Adapter 1
F Light Kit Assembly 1
G Fan Blades 4
H Glass Shade 1
I 50W Mini Candelabra Base Halogen Bulb 1
J SW90 Wall Control 1
HARDWARE BAG CONTENTS
Part Description Quantity
1 #8-32 x 11mm Truss Head Blade Screws 13
2 1/4-20 x 1/4” Round Head Screws
with Lockwashers 6
3 Steel Bushings 4
4 M4 x 6mm Pan Head Screw 1
5 #6-32 x 1/4” Truss Head Screw w/Lockwasher 1
6 Blade Balance Kit 1
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 3
1
2
A
B
C
D
E
F
H
I
3
5
44
6
EMERSON
4
3
2
1
J
G
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
Please call Emerson technical support at
1-800-654-3545 if you have any questions about
installation and operation of this ceiling fan.
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 7). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver One stepladder
One 1/4” blade screwdriver One wire stripper
One 3/8” open end wrench
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
4
ETL Model No.: CF530
2. Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
1. Unpacking Instructions (continued)
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 4
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF530
Figure 1
The fan must be hung with at least 7' of clearance from
floor to blades (Figure 1).
WARNING
!
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7 kg. (50 lbs.) or less”.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
3.1
Disconnect electrical power to the branch circuit at the
circuit breaker or fuse box before attempting to install
the ceiling fan mounting plate on the outlet box.
Figure 2
3. How to Hang Your Ceiling Fan
3.2
Pull the electrical supply black, blue, white and ground
wires through the center opening of the ceiling
mounting plate before securing the plate to the outlet
box (Figure 2).
Position the ceiling mounting plate onto the outlet box
and secure using the two outlet box screws, supplied
with outlet box (Figure 2).
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 5
AT LEAST
7'
CEILING
FLOOR
OUTLET BOX SCREWS (2)
CEILING MOUNTING PLATE HOOK
OUTLET BOX
CEILING
MOUNTING
PLATE
6
ETL Model No.: CF530
Figure 3
3. How to Hang Your Ceiling Fan (continued)
3.3
Place the fan motor onto the ceiling mounting plate
hook during wiring fan motor assembly to outlet box
(Figure 3).
Figure 4
3.4
Insert each steel bushing (4 supplied in parts bag) into
the four rubber boots until they are flush with the top
surface of each rubber boot (Figure 4).
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 6
CEILING MOUNTING
PLATE HOOK
FAN MOTOR
FAN MOTOR BRACKET
STEEL
BUSHING (4)
CEILING
MOUNTING
PLATE
RUBBER BOOT (4)
7
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF530
Figure 5
4. How to Wire Your Ceiling Fan
4.1
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan, light kit or wall control.
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and that
no bare wire is visible at the wire connectors,
except for the ground wire.
4.2
Securely connect the green grounding wire from the fan
motor mounting bracket, the green grounding wire from
the ceiling mounting plate and the green grounding wire
from the supply conductor (this may be a bare wire or a
wire with green insulation) (Figure 5).
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
Figure 6
4.3
Securely connect the supply white (neutral) wire to the
fan white wire (Figure 6).
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 7
SUPPLY GREEN
GROUNDING WIRE
FAN MOTOR MOUNTING
BRACKET GREEN
GROUNDING WIRE
CEILING MOUNTING
PLATE GREEN
GROUNDING WIRE
SUPPLY WHITE
(NEUTRAL) WIRE
FAN MOTOR
WHITE WIRE
8
ETL Model No.: CF530
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors (Figure 9). Do not operate fan until blades
are in place. Noise and fan damage could result.
WARNING
!
4. How to Wire Your Ceiling Fan (continued)
Figure 7
4.4
Securely connect the supply black wire to the fan black
wire (Figure 7).
Figure 8
Figure 9
4.5
Securely connect the supply red wire to the fan blue
wire (Figure 8).
NOTE: This fan requires a three conductor wire
installation to operate both the fan and light with
the included control. The red supply wire indicated
is typical in a three conductor cable with ground.
BP7484 Wyatt CF530 12/18/13 11:52 AM Page 8
SUPPLY BLACK
WIRE
WHITE SUPPLY
WIRE
BLACK SUPPLY
WIRE
3 CONDUCTOR
CABLE W/GROUND
WIRE BETWEEN
CEILING AND WALL
OUTLET BOXES
BLACK
FAN WIRE
WHITE
FAN WIRE
FAN MOTOR
BLACK WIRE
SUPPLY RED
WIRE
FAN MOTOR
BLUE WIRE
GROUNDING SUPPLY
WIRE
RED SUPPLY
WIRE
FAN MOTOR
MOUNTING
BRACKET GREEN
GROUNDING WIRE
BLUE FAN
WIRE
CEILING MOUNTING
PLATE GREEN
GROUNDING WIRE
Loading...