Emerson Islatrol SP-6TVN Installation Manual

Headquarters

Islatrol® SP Series – Surge Suppressor/Filter

User Manual

Surge Protection

30 Charles Street
Binghamton, NY 13905
P [phone]
P [phone]
F [phone]
E [e-mail]

Surge Protection for
Home and Office

– Islatrol® SP-6TVN and SP-6TN

IO-30112 Rev.2 11/09

SP-6TVN

SP-6TN

Congratulations on purchasing the Islatrol® SP-6TVN/SP-6TN multi-

Specifications

AC Power Protection

Phone Protection

Rated Output

15A

Modes of Protection

T-R, T-G, R-G

Peak Surge Current

39kA

Frequency Response

60dB Max

(SP-6TVN ONLY)

Connection Type

‘F’

Connection Type

RJ45

Peak Surge Current

5kA

Peak Surge Current

3kA

stage Industrial Strength Surge Suppressor with Active Tracking® Filter.
These instructions will insure your Islatrol® SP-6TVN/SP-6TN surge
suppressor is properly installed and functioning.

The Islatrol® SP-6TVN/SP-6TN is designed to protect 120 Volt electronics with up to
15-amp current carrying capability.
grounded to work. Ensure that any duplex receptacle used for the Islatrol®
SP-6TVN/SP-6TN is properly grounded.

Step 1: Connecting the Islatrol® SP-6TVN/SP-6TN to a Duplex
Receptacle

Remove the duplex receptacle mounting screw. If the duplex re­ceptacle face plate is metal, remove it otherwise leave in place.
Place the Islatrol® SP-6TVN/SP-6TN and the duplex receptacle face
plate, (if plastic) over the duplex receptacle. Insert the blades of the
Islatrol® SP-6TVN/SP-6TN into the duplex receptacle. Tighten the
mounting screw.

When installed in a properly grounded receptacle, Islatrol
6TVN/SP-6TN indicator light will be operational. If the indicator

light does not illuminate, it means the wall receptacle has an incor­rect ground. Try the SP-6TVN/SP-6TN in a different wall outlet. If it still doesn’t illuminate,
contact the office where you purchased your Islatrol® SP-6TVN.

You can reposition the Islatrol
clearance for your power cords if needed and connect up to 15 amps of equipment load.

Step 2: Connecting your Video Electronics to the Islatrol® SP-6TVN

Disconnect the video cable going to your home entertainment

system. Check to make sure that the small center wire inside the

video connection is straight, (not bent) and then connect it to the

“IN” of one of the video suppressor connections on the Islatrol®

SP-6TVN. Open one of the jumper wires that came with the

Islatrol® SP-6TVN. Connect one end to the “OUT” connection on the

Islatrol® SP-6TVN and connect the other end to the original connec-

tion on the home entertainment equipment.
If you have a second video device to protect, perform the same steps using the second

coaxial cable that came with your Islatrol

Step 3: Connecting your Telephone Electronics to the Islatrol®
SP-6TVN/SP-6TN

Disconnect the end of your telephone line where it comes out of
the wall. Connect it to one of the “OUT” telephone port connec­tions, (see diagram) on the Islatrol® SP-6TVN/SP-6TN. (Note: Do not
use the data port for telephone line suppression). Connect one end of
the telephone line patch cord that came with the Islatrol® SP­6TVN/SP-6TN to the “IN” line connection on the Islatrol® SP­6TVN/SP-6TN. Connect the other end to the original wall outlet.

Step 4: Connecting Network Electronics to

the Islatrol® SP-6TVN/SP-6TN

Disconnect the end of your network line from your computer or

router. Plug the end of the line to the Islatrol® SP-6TVN/SP-6TN

network connector ports marked “IN”. Connect one end of the

network line patch cord that came with the Islatrol® SP-6TVN/SP-

6TN to the “OUT” connection on the Islatrol® SP-6TVN. Connect the

other end to your computer or router.

The Islatrol® SP-6TVN/SP-6TN must be properly

®

SP-

®

SP-6TVN/SP-6TN receptacles on each side to provide

®

SP-6TVN.

Why the Islatrol® SP-6TVN/SP-6TN Industrial Strength Surge
Suppressor with

Active Tra cking® Filter

technology is

Simply the Best

power protection for your home and office equipment…

Special Circuitry: The Islatrol® SP-6TVN/SP-6TN multi-stage suppressor contains specia­lized circuitry to eliminate damage from surges. Part of the circuitry is an internal fuse
that will open in the rare event the Islatrol® SP-6TVN/SP-6TN is overloaded or exposed to
a high-energy surge beyond its capacity.

Indication: Although there is an indicator on the Islatrol® SP-6TVN/SP-6TN to show if the
suppressor is functioning, often suppressors are hidden behind furniture and other ob­jects that prevent you from seeing the indicator.

The Islatrol® SP-6TVN/SP-6TN has a second method to inform you if the suppression fails.
The internal fuse will open and you will lose power to your electronics. In the rare event
this occurs, please contact the office where you purchased your Islatrol® SP-6TVN/SP­6TN regarding any warranty repair/return instructions.

Load size: You may plug up to a 15 amp device into the SP-6TVN/SP-6TN without over­loading it.

Video: The Islatrol® SP-6TVN/SP-6TN video protection consists of two modules—either is
suitable for satellite dish protection, cable TV, cable modems, and any other video de­vice.

Telephone: The Islatrol® SP-6TVN/SP-6TN telephone protection is designed for any tele­phone application such as modems, fax machines, pay-per-view, DSL and other phone
use.

Warranty

The Islatrol® SP-6TVN/SP-6TN comes with a standard manufacturer’s limited warranty on
defects in materials and workmanship. The warranty provides repair or replacement ap­pliance coverage up to a limit. Contact the office where you purchased your Islatrol® SP­6TVN/SP-6TN for more information and warranty details.

Troubleshooting

If, in Step 1 and 2 on the previous page, the Islatrol® SP-6TVN/SP-6TN indicator did not
illuminate:

1. Try plugging it into a different wall receptacle. If the light illuminates, then the Isla-

®

trol

SP-6TVN/SP-6TN is operating properly and your first wall receptacle needs re-

pair. Please contact an electrician to repair your receptacle.

2. If the Islatrol
a. Your building wiring may not contain a ground conductor. In this case, the indicator

b. The Islatrol

On a very rare occasion, your protected electronic appliance may not have power. This is
an indication that the Islatrol
fuse is damaged. In this case, please contact your supplier for any warranty repair/return in­structions.

Nominal Operating Voltage 120V Connection Type RJ11
Maximum Operating Voltage 130V Peak Surge Current 2kA

Mode of Protection L-N, L-G, N-G

Video Protection

Modes of Protection L-G Modes of Protection L-G

®

SP-6TVN/SP-6TN does not illuminate in a different receptacle:

light will not illuminate but you will still have power out of the Islatrol

®

SP-6TVN/SP-6TN may have been damaged, please contact your

supplier for any warranty return/repair instructions.

®

SP-6TVN/SP-6TN has been overloaded and the internal

Network Protection

®

SP-6TVN.