Emerson Edco PC2-Tel Brochures and Data Sheets

Edco PC2-TEL

Two Line Telephone Protection (Modular)

The Edco PC2-TEL is a solid state, two-line telephone interface protector module.

This unit is specically designed to protect both phone lines required by commercial
re/security panels.

General Technical Specifications

Operating Voltage 250 VDC

Clamping Voltage 270 VDC

Operating Current 0.15 A

Peak Surge Current 160 A (10 x 1000 T & R to Ground)

Frequency Range 0 to 20 MHz

Insertion Loss < 0.1 dB at 20 MHz

SPD Technology Silicon Breakover Device w/Series PTC

Connection Type Terminal block w/ compression lugs

Terminals accept up to 10 AWG

Operating Temperature -40°C to +85°C

Dimensions (in / mm) 2.0˝ H x 1.0˝ W x 2.5˝ L

[50.8 x 25.4 x 63.5 mm]

(PC2TEL + PCB1B-WKEY Base)

Weight (oz / kg) 1 oz [0.03 kg]

Certications UL 497A, CUL

Warranty 5 years

EDCO PCB1B-WKEY BASE SOLD SEPARATELY

Features

■ Tip to ring protection

■ Tip and ring to ground protection

■ Over-current protection

■ Resettable solid state fuses — PTCs

■ UL Listed 497A

■ Requires PCB1B-WKEY base

Caution

Do not place this product in service on any signal line capable of continuously supplying
more than 150 mA.

Attention

Ne pas placer ce produit dans le service sur une ligne de signal capable de fournir en
permanence plus de 150 mA.

■ PC642PTU (Pass Thru Unit)

available for troubleshooting

■ 5 year warranty

Ordering Information

2 Line Telephone PC2-TEL

[60.96]

[25.40]

Installation Instructions

Terminal Assignments

PCB1B-WKEY

Even TerminalsOdd Terminals

9

Unprotected Pair 2

Field Side

Unprotected Pair 1

{

7

5

{

3

1

1.0”

• Connect ground terminals, positions 1 or 10 (internally
tied together) to Building Approved Ground. (See Edco
Tech Bulletin #2015) NOT intended for shield termination.
Install ground in accordance with all applicable codes.

• Edco PCB1B-WKEY accommodates 26 to 10 AWG wire.

10

8

Protected Pair 2

}

6

4

Protected Pair 1

}

2

Keying Pin

Electronics Side

2.125"

[53.98]

2.4"

DANGER!

V

Only qualied personnel should install or

service this system. Electrical safety pre­cautions must be followed when installing
or servicing this equipment. To prevent risk
of electrical shock, turn off and lock out all
power sources to the unit before making
electrical connections or servicing.

Seulement le personnel qualié doit installer
ou maintenir ce systéme. Des précautions
de sécurité en électricité doivent être suivis

lors de l’installation ou de la maintenance
de cet equipement. Pour eviter tout risque

de choc électrique, débranchez et verouiller

toutes les sources d’alimentation de cet
equipement avant de.

• Disconnect telephone line at the network interface before
installing this secondary device.

• This product is intended for indoor use only.

Emerson Network Power Contact information

Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: [phone]
T: [phone]
F: [phone]
E: [e-mail]

IO-50117 12/14 Rev. 4 Printed in USA

While every precaution has been taken to ensure accuracy and completeness herein, Emerson Network Power Surge Protection assumes no responsibility, and disclaims all liability, for damages

resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.

Emerson Network Power, the Emerson Network Power logo and Edco are trademarks

www.EmersonNetworkPower.com/Surge

and service marks of Emerson Electric Co. ©2014 Emerson Electric Co.