5000 BTU
MODEL:
EARC5RD1
INTRODUCTION
IMPORTANT SAFETY INSTRUCTION ............................................................................
ELECTRICAL REQUIREMENTS ....................................................................................
PACKING LIST .............................................................................................................
INSTALLATION & ASSEMBLY INSTRUCTIONS ...............................................................
USING YOUR AIR CONDITIONER ..................................................................................
CARE AND CLEANING ................................................................................................ .
TROUBLESHOOTING ...................................................................................................
1
2
3
4
7
10
11
below:
1
7
8
2
3
6 84
FIG. 1
23" to 36"
584 mm to 914 mm
Head
INTERIOR
WALL
STOOL
SILL
OFFSET
EXTERIOR
WALL
14 1/2" min
(368mm)
4
5
(Suggest to keep a downward
, to let accumulated rain water to drain out,
angle
76
from back side of the unit bottom.)
8
5
Head
FIG. 13
4
9
10
FIG. 9
FIG. 10
FIG. 11 FIG. 12
FIG. 14
6
1. Shows the set temperature.
Digital Display:
Operation modes are: Cool, Dry, Fan, and Auto.
Time is displayed using the timer setting.
Mode Button:
2.
through the various modes: Cool, Dry, Fan and
Auto.
Cool Mode:
conditioner to cool the room and at the same time
1
9
2
3
8
7
4
5
reduces humidity. Press the MODE button to
activate the cooling function. To optimize this
function adjust the temperature by pressing the up
and down arrows and the speed by pressing the
Fan Speed button.
Dry Mode:
the air to make the room more comfortable. Press
MODE button to set the DRY mode. An automatic
function of alternating cooling cycles and air fan
is activated.
Fan Mode:
Press MODE button to select FAN MODE.
Pressing the FAN SPEED button allows you to
change the fan speed setting from HI, MED, and
LO. If using the remote control, it will store the fan
speed setting of the previous use.
Auto Mode:
chooses the fan speed and the mode of operation
(COOL, DRY, or FAN). In this mode the fan speed
and the temperature are set automatically
according to the room temperature (
temperature is determined by the temperature
sensor located in the indoor unit.
Press the mode button to cycle
The cooling function allows the air
This function reduces the humidity of
This mode will only circulate the air.
In AUTO mode the unit automatically
Room
).
6
3. Use these buttons on the
and Button:
control panel and remote to increase or decrease
the Set Temperature or Timer.
Temperature range: 61 ~88 or 16 ~31 .
Press the SLEEP button, the Sleep
4. Sleep Button:
Light will be on after 10s. and the remaining lights
on the display will be off. In SLEEP mode, the airconditioner will automatically adjust the
temperature and fan speed to make the room more
comfortable during the night. The set temperature
will automatically raise by 1 every 30-60
minutes and at most change six times until the set
temperature is 28 .
Run time will depend on set temperature.
7
When the unit is in ECO mode, the
5. Eco Button:
light will turn on. In ECO mode, the unit will
turn-off once the room is cooled to the user set
temperature. The fan will also be off at this point.
The unit will turn back on when the room
temperature rises above the user set temperature.
Before the compressor stars, the fan motor will
run for a while, then it will stop for a while-and will
repeat to provide a much more comfortable-feeling
and save energy.
6. Turn the air conditioner on and
Power Button:
off.
7.
The Filter Check light will only turn
Filter Button:
on as a reminder to clean the filter after the fan
motor has been in operation for a total of 500
hours. To turn the light off, press the Filter Check
button.
Press the FAN SPEED button
9. Fan Speed Button:
to select the fan speed. In COOL MODE you can
choose the following settings: HI, MED, LO, or
AUTO. In FAN MODE you can choose from HI,
MED, and LO.
10.
Use the horizontal wheels
Directional Louvers:
to control horizontal airflow and the air deflectors
to control vertical airflow.
horizontal wheelair deflector air deflector
Timer Button:
Use these buttons on the control
8.
panel and remote to set the Timer.
Timer Off:
pressing the TIMER button. Set the time by
pressing the button or
The timed stop is programmed by
stop
until your
desired stop time is displayed, then press TIMER
button again.
Timer On:
button first
the button or .
a second time, set the stop time
button or .
When the unit is off, press TIMER
, set the temperature with pressing
Press TIMER button
with pressing the
Press TIMER button a
third time, confirm your settings and stop time.
The display will show the time your machine will
automatically turn on.
It can be set to automatically turn off or on
Note:
in 0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER button
again.
8
1
3
4
5
6
3
2
7
8
9
10
Use buttons on the control panel
5. Timer:
and remote to set the TIMER.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the time by
pressing the button or
desired stop time is displayed, then press TIMER
button again.
Timer On:
button first
the button or .
a second time, set the stop time
button or .
third time, confirm your settings and stop time.
The display will show the time your machine will
automatically turn on.
Note: It can be set to automatically turn off or on in
0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER button
again.
When the unit is off, press TIMER
, set the temperature with pressing
Press TIMER button a
stop
until your
Press TIMER button
with pressing the
1. Turn the air conditioner on and off.Power:
2. Press the COOL button to COOL mode.Cool:
and :3. Use these buttons on the control
panel and remote to increase or decrease the
Set Temperature or Timer. Temperature range:
61 ~88 or 16 ~31 .
Press the SLEEP button, the Sleep
4. Sleep:
Light will be on after 10s. and the remaining
lights on the display will be off. In SLEEP mode,
the air-conditioner will automatically adjust the
temperature and fan speed to make the room
more comfortable during the night. The set
temperature will automatically raise by 1
every 30-60minutes and at most change six
times until the set temperature is 28 .
And every
temperature.
Run time will depend on set
In AUTO mode the unit automatically
6. Auto Mode:
chooses the fan speed and the mode of operation
(COOL, DRY, or FAN). In this mode the fan speed
and the temperature are set automatically
according to the room temperature ().Room
temperature is determined by the temperature
sensor located in the indoor unit.
Press the FAN SPEED button
7. Fan Speed:
to select the fan speed. In COOL MODE you can
choose the following settings: HI, MED, LO, or
AUTO. In FAN MODE you can choose from HI,
MED, and LO.
To press the DISPLAY button, it can
8. Display:
switch off/on all lights or LED display.
9.
Eco:
When the unit is in ECO mode, the
light will turn on. In ECO mode, the unit will
turn-off once the room is cooled to the user set
temperature. The fan will also be off at this point.
The unit will turn back on when the room
temperature rises above the user set temperature.
Before the compressor stars, the fan motor will
run for a while, then it will stop for a while-and will
repeat to provide a much more comfortable-feeling
and save energy.
Fan Only:
Press the Fan Only button to FAN
10.
ONLY mode.
9
15
FIG. 15
10
11
For any questions or Technical Support,
Please Call Customer Service: 1-844-801-8880
12
Loading...