OPERATION
MANUAL
(v. 2.2.0)
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 2/114
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 3/114
WARNING:
TO
PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE, REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS PRODUCT IS INTENDED FOR USE INSIDE OF
ELECTRICAL PANEL ONLY
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF
UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE
PRODUCT’S ENCLOSURE THAT MAY BE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
WARNING:
Use only modems supported by this monitoring unit. Dixell S.
r.l.
can accept no responsibility for possible damage due the usage
of not supported modems.
WARNING:
Dixell
S.r.l
. reserves itself the
right to alter this manual without
notice. The last version available can be downloaded from the
website. Dixell Srl reserves the right to change the composition
of its products, even without notice, ensuring the same and
unchanged functionality.
WARNI
NG:
This manual d
escribes
XWEB
300D/XWEB
500D
/XWEB500
functionalities. Special cases are clearly specified. Hereby
instructions refer to firmware version 2.2 or previous.
WARNING:
This controlling and monitoring unit is compliant with standard
EN 12830 if it is used together with probes that are compliant with
standard EN 13485
WARNING:
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 4/114
INDEX
INTRODUCTION ................................................................................................................. 7
PACKAGING ....................................................................................................................... 8
MINIMUM SYSTEM REQUIREMENTS FOR THE PC-CLIENT........................................... 9
1 GENERAL INFORMATION ......................................................................................... 10
2 INSTALLATION........................................................................................................... 11
2.1 HARDWARE .................................................................................................................... 11
2.1.1 RS485 ....................................................................................................................................12
2.1.2 SERIAL ADDRESS .....................................................................................................................13
2.1.3 THE TTL OUTPUT .....................................................................................................................13
2.1.4 SERIAL ADDRESS OF THE INSTRUMENTS ......................................................................................14
2.1.5 TERMINATION RESISTOR............................................................................................................14
2.1.6 COMPATIBLE INSTRUMENTS .......................................................................................................14
2.1.6.1 PARTICULAR DEVICE SETUP ......................................................................................................................................14
2.1.7 REMOTE CONNECTION FROM A CLIENT PC ..................................................................................15
2.1.7.1 MODEM CONNECTION (“OR POINT TO POINT CONNECTION”) .............................................................................15
2.1.7.2 INTRANET / ETHERNET CONNECTION ......................................................................................................................15
2.1.7.3 INTERNET CONNECTION .............................................................................................................................................16
2.2 LOCAL LCD USER INTERFACE (COOLMATE MODELS ONLY) .................................... 17
2.2.1 AVAILABLE MENU ....................................................................................................................17
2.2.1.1 SETUP MENU..................................................................................................................................................................17
2.2.1.1.1 DATE / TIME...............................................................................................................................................................18
2.2.1.1.2 DEVICE MENU ...........................................................................................................................................................18
2.2.1.1.3 ALARM MENU ............................................................................................................................................................19
2.2.1.1.4 PRINTOUT .................................................................................................................................................................19
2.2.1.1.4.1 AUTOMATIC PRINTING MENU ........................................................................................................................19
2.2.1.1.4.2 MANUAL PRINTING MENU ..............................................................................................................................20
2.2.1.1.5 PASSW ORD ...............................................................................................................................................................20
2.2.1.2 VIEW MENU ....................................................................................................................................................................21
2.2.1.2.1 MODIFY SETPOINT ..................................................................................................................................................21
2.2.1.2.2 DATA FROM ARCHIVE .............................................................................................................................................22
2.2.1.3 SYSTEM STATUS ...........................................................................................................................................................22
2.2.1.4 GLOBAL COMANDS .......................................................................................................................................................22
2.2.1.5 ABOUT MENU .................................................................................................................................................................22
2.3 CONFIGURATION AND ACCESS ................................................................................... 23
2.3.1 MICROSOFT WINDOWS: POP-UP BLOCKER AND COOKIES ...............................................................23
2.3.2 MICROSOFT WINDOWS: CACHE FILES .........................................................................................25
2.3.3 THIRD PART SOFTWARE AND XWEB ..................................................................................26
2.3.4 SYSTEM CONFIGURATION ..........................................................................................................27
2.3.5 XWEB SETUP ..........................................................................................................................28
2.3.6 SYSTEM SETUP ........................................................................................................................29
2.3.7 NETWORK SETUP .....................................................................................................................30
2.3.8 MODEM SETUP ........................................................................................................................31
2.3.9 DIALUP SETUP ..........................................................................................................................31
2.3.10 E-MAIL SETUP ..........................................................................................................................32
2.3.11 SMS SETUP ..........................................................................................................................33
2.3.12 PRINTER SETUP .......................................................................................................................33
2.3.13 XCENTER .............................................................................................................................33
2.3.14 SYSTEM MESSAGES ..................................................................................................................34
2.3.14.1 MANUAL TEST: E-MAIL, FAX OR SMS SENDING .......................................................................................................34
2.3.14.2 SENDING AUTOMATIC REPORTS (ONLY FOR XWEB WITH SCHEDULER)..........................................................34
3 USING XWEB ............................................................................................................. 35
3.1 SYSTEM LOG-IN ............................................................................................................. 35
3.2 HOME PAGE ................................................................................................................... 35
3.2.1 SYSTEM ACCESS......................................................................................................................36
3.2.2 IDENTIFICATION / TIME ..............................................................................................................36
3.2.3 SERVER PROPERTY ..................................................................................................................36
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 5/114
3.2.4 ALARMS ..................................................................................................................................36
SHORTCUTS ......................................................................................................................................37
3.3 CONTROLLERS SETUP ................................................................................................. 37
3.3.1 DEVICE FIND OF THE INSTRUMENTS CONNECTED TO THE “RS485” SERIAL LINE................................37
3.3.2 CATEGORIES ...........................................................................................................................38
3.3.2.1 DEVICE TIPOLOGY ........................................................................................................................................................38
3.3.2.2 RECORDING INTERVAL ................................................................................................................................................39
3.3.2.3 RTC SYNCRONIZATION ................................................................................................................................................39
3.3.3 SCHEDULER (ONLY FOR XWEB500DIN) ........................................................................................39
3.3.3.1 PRINTING EVENTS ........................................................................................................................................................45
3.3.3.2 SYSTEM EVENTS ...........................................................................................................................................................46
3.3.3.3 USING THE SCHEDULER ..............................................................................................................................................46
3.3.4 ALARMS ..................................................................................................................................47
3.3.4.1 ALARM TYPOLOGY AND ALARM LEVELS ..................................................................................................................47
3.3.4.2 DESTINATION OF THE ALARM MESSAGES ...............................................................................................................48
3.3.4.3 ALARM LEVELS ..............................................................................................................................................................49
3.3.4.4 ALARM TYPOLOGY MANAGEMENT ............................................................................................................................50
3.3.4.5 QUEUED MESSAGES ....................................................................................................................................................51
3.3.5 CALENDAR FUNCTION ...............................................................................................................51
3.3.6 DEVICE CONFIGURATION ...........................................................................................................55
3.3.6.1 SELECT A DEVICE .........................................................................................................................................................55
3.3.6.2 ASSIGN THE NAME OF THE CONTROLLER ...............................................................................................................56
3.3.6.3 ASSIGN THE CATEGORY TO THE DEVICE “DEVICE CATEGOR Y SETUP” ............................................................56
3.3.6.4 ASSIGN THE ALARM T YPOLOGY ................................................................................................................................56
3.3.6.5 DEFINE THE DIGITAL, ANALOGUE INPUTS AND THE STATUS ..............................................................................57
3.3.6.6 CLONE FUNCTION .........................................................................................................................................................57
3.4 STARTING MONITORING DATA .................................................................................... 58
3.5 DEVICES MENU .............................................................................................................. 59
3.5.1 SINGLE VIEW ............................................................................................................................59
3.5.2 RUN TIME ................................................................................................................................61
3.5.3 PARAMETERS ..........................................................................................................................65
3.5.4 LAYOUT FUNCTION (ONLY FOR XWEB500DIN) ..............................................................................67
3.5.4.1 LAYOUT EDITOR ............................................................................................................................................................67
3.5.4.2 LAYOUT VIEW.................................................................................................................................................................75
3.5.5 GLOBAL COMMANDS FUNCTION (ONLY FOR XW EB500DIN) .............................................................75
3.5.5.1 GLOBAL EDIT..................................................................................................................................................................75
3.5.5.1.1 DIGITAL INPUT SENDING COMMANDS .................................................................................................................77
3.5.6 PERFORMANCE METER (ONLY FOR XWEB500DIN) .................................................................79
3.5.6.1 INTERPRETING THE %COOL .......................................................................................................................................83
3.5.6.2 GLOBAL COMMANDS ....................................................................................................................................................83
3.6 CRO (ONLY FOR XWEB WITH CRO) ............................................................................. 83
3.7 DATA MENU .................................................................................................................... 85
3.7.1 DISPLAY THE GRAPHS ...............................................................................................................86
3.7.2 EXPORTING DATA – SINGLE DEVICE .......................................................................................89
3.7.3 EXPORTING DATA – MULTIPLE DEVICES ................................................................................89
3.7.4 EXPORT TO USB PEN DRIVE ........................................................................................................91
3.7.5 DELETE DATA ...........................................................................................................................92
3.7.6 DISPLAY THE GRAPHS W ITH LOCAL PC .........................................................................................92
3.8 ALARM MENU ................................................................................................................. 97
3.8.1 HYSTORICAL ALARMS ................................................................................................................97
3.9 PERMISSIONS ................................................................................................................ 98
3.9.1 MANAGING THE USERS ..............................................................................................................99
3.10 TOOLS SECTION ......................................................................................................... 99
3.10.1 DATA LOG STATUS ....................................................................................................................99
3.10.2 RS 485 TEST ..........................................................................................................................99
3.10.3 SERVER STATUS ....................................................................................................................100
3.10.4 MESSAGE STATUS ..................................................................................................................100
3.11 INFORMATION MENU ............................................................................................... 101
3.11.1 SYSTEM VERSION ...................................................................................................................101
3.11.2 SYSTEM UPDATE .....................................................................................................................101
4 SAFETY AND ALLOWED USE................................................................................. 102
4.1 SYSTEM SPECIFICATION ............................................................................................ 103
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 6/114
5 APPENDIX ................................................................................................................ 104
Appendix A: DEVICE ADVANCED SECTION ............................................................. 105
Appendix B: GLOSSARY ............................................................................................ 107
Appendix C: ACCESSORIES ...................................................................................... 109
Appendix D: GPRS CONNECTIVITY (ONLY FOR DIN) .............................................. 109
Appendix E: CONNECTIVITY AND SENDING SMS ................................................... 113
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 7/114
IINNTTRROODDUUCCTTIIOONN
Congratulations! This manual will teach you everything about XWEB server, the most powerful and
configurable tool for Controlling and Monitoring.
This manual is a comprehensive guide to your XWEB. You will find all the information you need to work with
the unit.
The XWEB is based on the latest technology of the Internet world to display the WEB pages contained into
the unit itself. The Linux operative system guarantees maximum efficiency and stability support for this kind
of product.
All future software releases developed by Dixell will be available via internet connection. The Hardware
inside the unit, based on high performance electronic boards, does not require any maintenance.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 8/114
PPAACCKKAAGGIINNGG
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify
your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay.
Only the consignee (the person or company receiving the unit) can file a claim against the carrier for
shipping damage.
We recommend that you retain the original carton and packing materials for use should you transport or ship
the unit in the future.
Inside the box you must find these articles:
The XWEB server unit [1].
One CD Rom containing the Operative manual and software [2].
Power supply [3]
Quick setup manual (Fast installation) [4].
If one of the above items is damaged, do not hesitate to contact your supplier.
MODEM (not included)
When working with the modem connection always check the kind of modem you are going to install by
verifying, with Dixell, the complete compatibility with the XWEB unit.
Dixell is not responsible for bad functioning of unknown or untested devices.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 9/114
MMIINNIIMMUUMM SSYYSSTTEEMM RREEQQUUIIRREEMMEENNTTSS FFOORR TTHHEE PPCC--CCLLIIEENNTT
When connecting through local or remote connection, the client PC computer, must have installed these
components:
Java Virtual Machine v1.6 or higher
Microsoft Internet Explorer 8. Usage of newer browsers, as Internet Explorer 9 or Mozilla Firefox or Google
Chrome, is recommended implementing better some internet standards.
If necessary, inside the CDROM you will find the Java Virtual Machine program distributed by Sun
Microsystems.
Dixell S.r.l. is not responsible for any kind of damage occurring after the loading of the Java Virtual Machine
program into the user’s PC.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 10/114
11 GGEENNEERRAALL IINNFFOORRMMAATTIIOONN
XWEB is a Controlling and Monitoring system based on “WEB server” technology. In this document we can
refer to XWEB as ‘server’. It is capable to communicate data to one external Client with the same kind of
procedure used by the Internet Web Sites. Client need only a standard Browser such as Microsoft
Explorer.
The Web Pages with all the information are contained into the server itself; Linux operative system ensures
maximum efficiency and security.
The server reads, logs and checks the data coming from the Dixell instruments connected to a RS485 line.
The communication protocol is the Modbus-Rtu. The XWEB is capable of recognising also most of the
Modbus-Rtu compatible instruments not manufactured by Dixell.
ATTENTION: Always check the proper RS485 connections (see 2.1.1 rs485)
ATTENTION: Dixell S.r.l. reserves itself the right to analyse the Modbus-RTU compatibility of other
manufacturer’s devices before ensuring their integration into XWEB system.
Clients to Server connection possibility (PC—XWEB)
Modem: point to point through local and remote modem devices (“Creating a Remote Access under
Windows”);
Intranet / Internet: where available a static IP, using the standard socket 10 Base-T with RJ45
connector.
Cross over Ethernet cable: You can plug a bridge network cable into RJ45 socket of XWEB and on the
other side into your PC network adapter. Ask your network administrator to properly setup your PC to be
able to access XWEB web pages.
The User interface is defined by the Browser program and it is the same for all kind of connections.
The PC-client needs only a standard Browser, there is no need to install any kind of software
Some pages created by the web server rely on Java and they need the Java Virtual Machine program that is
normally installed in the latest Browsers and operative systems.
Features and functions included into the XWEB management:
Data monitoring and recording, alarm detection and recording of the instrument connected.
Alarm management defined by the User with visible signals (onboard led), or relay switching or remote
transmission via Fax, E-mail or sms.
Interactive commands to manage the connected instruments.
Parameter table programming.
Graphic or table viewing and printing of the recorded data.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 11/114
22 IINNSSTTAALLLLAATTIIOONN
2.1 HARDWARE
ATTENTION: to protect both yourself and the server from electrical hazards the XWEB should remain turned
off until you are finished connecting all electrical devices to the unit.
To avoid accidental start of the unit, remember to plug in electrical cable only when you have
finished setting up all other connection.
(ONLY FOR DIN MODELS)
3
: alarm relay 1 (**)
4
5
: alarm relay 2 (**)
6
7
: System alarm relay
:7-8 Alarm
:7-9 Alarm present
8
9 15
: digital input (**)
16
12 (-)
: RS 485
13 (+)
14 ()
: 1-2 XWEB500 Power supply
: 10-11
External
GSM
modem power
supply (*)
: USB external peripherals
: COM port for external modem
: Telephone jack (only for internal
modem)
: RJ45 LAN connector
LED
Led Color
Description
Alarm
Red RS485 Alarm
Rec Orange
Data recording
Power
Green
System turned on
Status
Green
Messages are being sent
System
Red System alarm
Alarm2
Red Alarm Relay 2 status
Alarm1
Red Alarm Relay 1 status
(*)= 12Vcc - 250mA. Modem supported TC35-KIT (Siemens TC55i)
(**)= only for XWEB500DIN
WARNING: The status of led system is directly linked to the status of the relay “System alarm”.
WARNING: with XWEB300D the 'system relay’ acts as AUX taking following logic:
• at rest (XWEB off) closed contacts 7:09
• in case of alarm closes on 7-8
• turning on for a few seconds closes on 7-8. then if there are no alarms back to rest and closing on 7-9.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 12/114
(ONLY FOR COOLMATE
MODELS)
1
: Alarm 1 output relay
2
3
: Alarm 2 output relay
4
5
: System Alarm
:5-6 No Alarm
:5-7 At least one alarm
6
7 8
: modem reset relay
9 10
: digital input
11 12 (+)
: RS 485 socket
13 (-) 14 ()
: Power supply connector
: USB socket for PC connection
: USB socket for devices connection
: External modem socket
: Internal modem line connector
: RJ45 Ethernet connector
WARNING: the relay 'reset modem' is excited to reset, under conditions of disuse every two minutes and
before each use (to fax, to dial-up, etc..).
2.1.1 RS485
To be connected to the serial line all the Dixell Modbus instruments must be provided with direct RS485
terminals or the “TTL”-RS485 interface (XJRS485 or XJ485). Check the instrument manuals for more
information.
The RS485 line is mainly based on two polarised terminals. Please beware to respect the right sequence for
all the devices connected to the serial line.
Follow these important advises:
The RS485 serial line must reach all the instruments where they are installed.
Beware to the wire polarities when screwing them into the instrument terminals.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 13/114
2.1.2 SERIAL ADDRESS
The cable must have 2 or 3 wires with shield, minimum section 0,5mm2 (e.g. the BELDEN 8772).
From the XWEB position the cable reaches all the instrument positions.
Do not execute loops or derivations:
Right connection
Wrong connection
Do not connect shield to ground.
Do not connect the “Gnd” terminal.
Remember to draw a map of the line. This will help you to find an error if something is wrong.
The instrument with RS485 have “+” and “-“ terminals, respect the polarity.
To keep the line balanced it is necessary a 120 Ohm resistor at the end of the line (you can use the RS
485+ and RS 485- terminals of the last instrument connected).
2.1.3 THE TTL OUTPUT
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 14/114
The instrument with RS485 on board do not need any kind of external interface module.
For instruments with external interface: keep the TTL cable away from power cables or frequency
sources.
The XJ485 external interface must be connected with TTL cable to the instrument with TTL compatibility.
2.1.4 SERIAL ADDRESS OF THE INSTRUMENTS
Each instrument must be defined by its unique address.
Check the address into the Adr parameter value. Take reference to the instruction manual of the
instrument itself to find the right procedure to enter the programming and set the value.
The easiest way to work with the category functions is to set the addresses progressively for similar
groups of instruments which have the same application.
2.1.5 TERMINATION RESISTOR
To keep balanced the RS485 the beginning and the end of line must be closed with a resistor of 120Ω. If
XWEB is placed at the beginning or at the end of the line, please active its termination resistor by adding
a jumper in position 2 (JMP2 on the back side of the unit). DO NOT add the jumper if XWEB is placed in
the middle of the RS485 line.
2.1.6 COMPATIBLE INSTRUMENTS
For a complete list please read Appendix C.
2.1.6.1 PARTICULAR DEVICE SETUP
All controllers equipped with 2 serial addresses (XC400/600/800/900, XH200/300/400 etc.) must be used
with both addresses equal.
iCHILLs need to activate a particular value in the “Advanced” section. User must check “Force Device
On status”. Remember to stop-start acquisition after this operation.
To use non Dixell, but Modbus compatible controllers (such as Energy Analyzer by Carlo Gavazzi)
follow this instructions:
a) Go to “Configuration” then “Devices”.
b) On the drop down menu “Actions” select “New...”.
c) A new pop-up window will appear: fill in the blank with the name of the controller and the ADR.
d) Choose the proper device model (e.g. “ENERGY_800000000000000”).
e) Press “Create”
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 15/114
2.1.7 REMOTE CONNECTION FROM A CLIENT PC
2.1.7.1 MODEM CONNECTION (“OR POINT TO POINT CONNECTION”)
It represents the most common method where the LAN (intranet / Ethernet / internet) is not available.
It is strongly advised to use a dedicated telephone line.
IMPORTANT: Use exclusively modem devices approved by Dixell.
Remember that many modems are not compatible with Linux. The list of compatible models can
be found under the menu: Configuration – System - Modem. In appendix E, you can find the
complete list of accessories together with their commercial name. Dixell can provide you these modems. You
can decide to buy them in your country, but do not use different models from the ones stated here. Dixell is
not responsible for any action depending on a modem that is not present in the official list of supported
accessories.
External Modem.
Connect the modem to the COM Port on the back side using the modem cable commonly included into the
modem packaging itself.
The reset of XWEB modem is directly controlled by the XWEB Server through the COM port, but if you use a
GSM modem remember to use the external relay to cut the modem power supply to reset it.
Connect the modem to the telephone line with the phone cable included into the modem packaging.
Remember to check if there is a switching machine (add the prefix digit). The connection procedure is
divided in two parts:
In the first part it is necessary to create the Remote Access, in your remote PC, set with the telephone
number of the line where the XWEB is connected to. You have to use Dixell as Username and Password.
The second is the procedure you will ever use: after launching the new Remote Access that will engage the
line via the modem, start the Browser from your PC and insert the address http://192.168.0.150 into
Explorer/Netscape address bar. Proper information about setting up a dial-up connection for the client PC,
can be found inside the INSTALLATION MANUAL on §4.3.
2.1.7.2 INTRANET / ETHERNET CONNECTION
The Intranet or Ethernet connection should be initially managed by the net administrator which will assign
one free IP address to reach the Server. This number is an example of what you should expect:
http://192.168.000.111.
After receiving the address from your network Administrator the XWEB must be set with this number.
Use a standard RJ45 network cable to connect the unit to your existing LAN.
The Intranet method allows the connection to interact with XWEB from all the PC Clients. Insert the net
address assigned by the administrator into the Browser address bar. Bookmark the address with
personalised name for the future connections.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 16/114
2.1.7.3 INTERNET CONNECTION
It is necessary a STATIC IP address for the XWEB which is normally assigned by the Provider of your
internet services.
The Internet connection allows XWEB to be reached from all PC-clients. Insert the net address assigned by
the administrator into the Browser address bar. Bookmark the address with personalised name for the future
connections.
Ask your provider for more details about the rent of a static IP.
This the internet system requirements for the best result:
Wide band connection.
At least 1 static IP addresses for the XWEB.
The internet connection is established through a device called Router that receives and sends the data as
interface between an Intranet and Internet. The Provider also assigns the address of the router that is called
IP WAN.
Remember that the default value of the IP of the XWEB is: 192.168.0.150.
Depending on the contract the Provider can also supply the router, otherwise the user can buy it separately.
REMEMBER: ask qualified personnel for the router installation by using this information:
Used ports that are mapped to the LAN side:
22 (used for SSH connection)
80 (used for the Error! Hyperlink reference not valid. access)
The above ports are all related to the XWEB IP address 192.168.0.150.
While the ports on the WAN side are:
http (To access the XWEB)
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 17/114
2.2 LOCAL LCD USER INTERFACE (COOLMATE MODELS ONLY)
The local user interface consists of 8 keys:
KEY FUNCTION
VIEW Direct access to the runtime data
MENU Go to configuration menu
CLEAR Exit current menu; delete a character
ENTER Enter a menu, Enter current allarm list
<- left arrow
/\ up arrow
\/ down arrow
-> right arrow
When there is no alarm, the LCD is:
D I X E L L X W E B 5 0 0
X W E B 5 0 0
S Y S T E M O K
1 0 : 0 1 1 5 / 0 3 / 2 0 0 7
When there i san alarm the LCD is:
D I X E L L X W E B 5 0 0
X W E B 5 0 0
0 3 5 - N O L I N K
1 0 : 0 1 1 5 / 0 3 / 2 0 0 7
The third row displays the address of the controller and the type of the alarm. To stop the buzzer press
ENTER, automatically the current alarm list will be displayed. To be able to reset an alarm the user must
have received the permission by the administrator.
2.2.1 AVAILABLE MENU
By pressing the MENU key:
-> Setup
View
System status
Global command
About
2.2.1.1 SETUP MENU
Press ENTER when you are in setup:
-> XWEB 500 unit
Date / time
Device(s)
Alarmi
Printout
Password
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 18/114
XWEB 500 unit let you setup:
-> Language
Identification
Delete archive
Network
Modem
Dial up
e-mail
SMS
FAX
Printer
Delete archive completely empties the recorded temperatures and alarms. It empties the
corresponding database
Network is for the setup of the network. The system must be rebooted to apply a new setup.
Modem is for the modem setup.
Dial up is to setup the dial-up connection
e-mail is for the e-mail setup. The option “Testing e-mail” let you send a test e-mail.
Printer is to setup the USB printer. The setup via web-browser is strongly suggested for this entry.
2.2.1.1.1 DATE / TIME
To setup, date, time and timezone
2.2.1.1.2 DEVICE MENU
-> Add
Delete
Setup
Recording interval
To add a new device the system must be in STOP mode (i.e. RS485 reading must be turned off).
Add is to add a new device. Only 100 devices can be added [the maximum number of devices may
vary depending on the considered model]
Delete is to remove a device.
Setup is to configure a device according to the following parameter:
Address: ADR parameter
Name: name of the controller
Interval: recording interval
Read: enable data reading for the selected controller
Record: enable data recording for the selected controller
RTC: enable real time clock synchronization
Print: enable the printout for the selected controller
Recording interval is to setup the interval between two samples of data. Only 1 category can be
setup in the LCD. Other categories can be added by means of the WEB user-interface.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 19/114
2.2.1.1.3 ALARM MENU
Alarm management by means of the LCD can setup only 1 user. To add new user please use the WEB
user-interface
-> Delay
Accumulation
Send FAX: Si/No
Send e-mail. Sì/No
Send SMS: Sì/No
Receiver(s)
Relay
Delay is to filter the alarms. If an alarm lasts less than the delay, XWEB 500 only records it in the
alarm log. If it lasts more than the delay, XWEB 500 will send it according to the accumulation time.
Accumulation time let you group together different alarms that belongs to the same level. Only one
alarm message will be sent: inside this main message all the others will be added.
Send FAX enables fax sending
Send e-mail enables e-mail sending
Send SMS enables SMS sending
Receivers let you setup the default receiver’s information:
o Default name can be modified by pressing ENTER
o FAX 1: first fax number
o FAX 2: back-up fax number
o E-mail: e-mail address
o SMS: mobile phone number
Relay let you setup the ALARM1 and ALARM2 relays:
o ALARM1: enable/disabled
o ALARM2: enable/disabled
o BUZZER: enable/disabled the buzzer
2.2.1.1.4 PRINTOUT
Two different type of printouts are available.
-> Automatic printing
Manual printing
2.2.1.1.4.1 Automatic printing MENU
-> time
Print Data. Yes/No
Print alarms. Yes/No
Time is to setup the time of the day a printout is automatically printed by the XWEB500
Print Data is to print the recorded temperatures
Print Alarms is to print the list of the alarm
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 20/114
2.2.1.1.4.2 Manual printing MENU
-> Alarm
Data
XWEB500 Setup
Device(s) Setup
Alarm is to choose between the current alarm list and the recorded alarm list
Data is to choose the recorded temperature in the archive
XWEB500 setup prints the setup of the XWEB500 (network, receivers, users, etc…)
Device(s) Setup prints the setup of the controllers
2.2.1.1.5 PASSWORD
The management of the user by means of the local LCD is different from the one by means of the WEB user
interface. Security management is turned off by default.
-> Users’ permissions: Yes/No
When users’ permission is ON, a password for each user must be set:
-> Users’ permissions: Yes/No
Administrator
User 1
User 2
User 3
User 4
Please select the Administrator and assign it a password. Automatically it appears “Password:*”. Press
ENTER to modify it.
Please select user 1 and assign it a password. It is possible to modify the following options:
-> Send command
Global command
Modify setpoint
Modify unit
Modify time
Modify devices
Modify alarm
Alarm reset
Send command is to send a command to the controller
Global command is to send a global command (if available)
Modify setpoint let you modify the setpoint of a controller
Reset alarm to reset an alarm (buzzer and relays)
When the user insert the password the system grant him complete access for 1 minute only. After this
timeout the user must insert the password again.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 21/114
2.2.1.2 VIEW MENU
By pressing VIEW the following options are available:
-> Data
Alarm
Tools
Data is to browse the current/recorded temperatures
Alarm is to browse the current/recorded alarms
Tools let you start the RS485 line test
2.2.1.2.1 MODIFY SETPOINT
By using Data menu, then actual, it is possible to modify the setpoint of a controller. This is the view layout:
-> Name of the controller
>---A-INPUT---------<
Air Temperature: 4.20°C
>---SETPOINT---------<
Set point: 4°C
>---D-INPUT---------<
Open door: OFF
Generic alarm: OFF
>---STATUS---------<
ON/OFF: ON
Defrost: OFF
>---OUTPUT---------<
Defrost: OFF
Fan: OFF
Compressor: ON
>---ALARM ---------<
High Temperature: OFF
Low Temperature: OFF
Generic alarm: ON
>---COMMANDS---------<
OFF
ON
DEFROST
…
>---A-INPUT---------< means analog inputs (probes)
>---SETPOINT---------< setpoint
>---D-INPUT---------< means digital input
>---STATUS---------< reports the status of the controller
>---OUTPUT---------< reports the outputs staus of the controller
>---ALARM---------< current alarm list
>---COMMAND---------< current command list
To modify the setpoint move the marker “->” to highlight the actual setpoint and modify it by pressing
ENTER. Increse/decrease the current value by means of the up/down arrow keys. Press ENTER to confirm
To send a command, scroll the list until you reach the section >---COMMANDS---------<, select the command
and press ENTER. To confirm press ENTER again.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 22/114
2.2.1.2.2 DATA FROM ARCHIVE
-> View
From: 10:30 10/01/2007
Interval: 01:00
The archive can be browsed between the “From” date and the today day. (in the above example the archive
will show data from 10:30 a.m. January 10th 2007 until today). Interval is the distance between to samples of
data (i.e. time difference between to 2 recorded temperatures). Move the marker “->” above “view” and press
ENTER. To move to the next recorded temperatures, press VIEW.
2.2.1.3 SYSTEM STATUS
-> Data reading: Yes/No
Data recording: Yes/No
Alarm sending: Yes/No
Data reading starts the monitoring unit
Data recording starts the recording of the temperatures.
Alarm sending starts the alarm sending procedure
2.2.1.4 GLOBAL COMANDS
This function can be activated only by means of the WEB user interface. Once a command is available, it will
be showed in this list.
2.2.1.5 ABOUT MENU
This menu shows the release of the XWEB500, moreover it shows the unique MAC address of the unit.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 23/114
2.3 CONFIGURATION AND ACCESS
Before turning on the XWEB read these notes.
The local access via network cable is the fastest way to manage the first setup of the unit. Be sure the Pcclient is provided with Java Virtual Machine. Launch the Browser and insert the default address
192.168.0.150.
2.3.1 MICROSOFT WINDOWS: POP-UP BLOCKER AND COOKIES
XWEB uses some pop-up windows to show the user the real status of each operation, unfortunately these
pop-ups are blocked by Windows pop-up blocker. Usually Internet Explorer adds a yellow bar to inform you
about the blocked pop-up (image below).
To avoid this problem, please follow these rules:
1. Go to “Tools” and then “Internet Options…”:
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 24/114
2. From the TAB “Privacy”, apply the “Default” settings and press the button “Settings…” on the bottom
right corner.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 25/114
3. Add the default address of XWEB, i.e: 192.168.0.150.
Please remember to add each IP address you will use to this list.
2.3.2 MICROSOFT WINDOWS: CACHE FILES
Often referred to as the cache, the Temporary Internet Files folder contains a kind of travel record of the
items you have seen, or downloaded from the Web, including images, sounds, Web pages, even cookies.
Typically these items are stored in the Temporary Internet Files folder.
Storing these files in your cache can make browsing the Web faster because it usually takes your computer
less time to display a Web page when it can call up some of the page's elements or even the entire page
from your local Temporary Internet Files folder, but at the same time can prevent you from receiving correct
information from the XWEB you are connect to.
These files also take up space, so we suggest deleting them periodically. When you clear out the files stored
in your cache you go through the “clearing the cache” procedure.
To clear your cache:
1.On the Internet Explorer Tools menu, click Internet Options. The Internet Options box should open to the
General tab.
2.
On the General tab, in the Temporary Internet Files section, click the Delete Files button. This will delete all
the files that are currently stored in your cache.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 26/114
2.3.3 THIRD PART SOFTWARE AND XWEB
As general rule please remember that software such as antivirus programs, firewall programs, toolbars
(Yahoo and Google bar) may prevent you from connecting properly to XWEB. We strongly suggest to check
these softwares setup and add the IP address of XWEB to the trusted site list of your software. As far as
firewall is concerned, add port 80 and port 22 to the allowed ports forwarding, of course all the TCP/IP
requests coming from the IP address of XWEB must be allowed.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 27/114
2.3.4 SYSTEM CONFIGURATION
As soon as the power supply cable is plugged in, the system starts loading.
The on-board display shows you the bootstrap procedure with a slide-bar
After the first loading of the operative system, the user is required to setup the XWEB.
The first window asks you to log-in to the system. Use Admin as “User name” and “Password”.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 28/114
2.3.5 XWEB SETUP
Click on “Configuration” -> “System” roll-down menu. This window will appear:
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 29/114
2.3.6 SYSTEM SETUP
Click on “System setup” to adjust System name, description, language, date/time and time-zone format.
They are important because the system will use its time stamp to record and send alarm.
Only for XWEB300: you can manage the alarm relay as AUX.
In the section "XJR40D configuration" configure the extension of the alarm relays with XJR40D: the device
must already be present in the configuration of Modbus devices (go to "Devices" or "Find Device"). Select
the module XJR40D to use for the extension alarms then configure alarm delivery in the "Alarms" page (level
parameters). Warning: the polarity of the relay module XJR40D is managed by the parameters of the module
itself: refer to the documentation of the module for testing and / or programming it.
Enable/Disable of this feature is shown in the system log.
1592028000 XWEB300D_500_500D opr GB r2.2.0 2013.08.01.docx XWEB500/300 30/114
2.3.7 NETWORK SETUP
By clicking “Network Setup” is possible to
customize all network settings. The
default IP is 192.168.0.150, if you change
it, please refer to this new number each
time you encounter the default IP inside
this manual.
The next window allows you to setup the
network. You can choose “No network”, it
means you will not be able to reach your
XWEB using intranet/lan access. This is
an uncommon situation. On the other side
if you check the radio button “fixed
network”, you have to fill in the blank
labels. We suggest you, before
proceeding, to contact your network
administrator to get help.
IP ADDRESS: you need this unique
number to identify your XWEB. There are
2 kind of IP numbers: private and public
ones. The first are usually used to setup
an intranet/lan where all clients do not
need to be reached from outside. We can
compare this situation to a close
environment: communication is possible
only among IP belonging to this private
range. For example IP numbers
192.168.xxx.yyy defines a private
network.
NETWORK MASK:
is just like a filter, 255.255.255.0 means
XWEB
can directly reaches only PCs belonging
to its own IP range. All other requests will be sent to a valid gateway.
GATEWAY ADDRESS: You have to compile this field with a valid gateway IP number. Gateway machines
are a kind of portal through which all data that can not directly reach the target IP, is sent.
PRIMARY/SECONDARY DNS: In the internet world you can reach a web server using its name, for example
www.dixell.com, by typing the name into your web-browser address bar. Due to the protocol used to
guarantee performance and security, all names are converted into IP numbers. This operation is made by a
DNS server. Usually your ISP or your network administrator can provide you a valid DNS number. DNS are
also mandatory to use e-mail and the internet upgrade procedure.
Webserver port number: use it to set a different port number for the web server. In the example the new
address to go to XWEB500 is http://192.168.0.150:8080
DHCP Server: use it to force Ethernet network configurations from XWEB. This parameter is usually
disabled and please enable this function only after consultancy by network administrator.
Loading...