Emerson CX Installation Manual

Edco CX Series

CCTV & Data Applications/Coax

The Edco CX06-M, CX06-MI and CX06-MI-SBL Surge Protective Devices (SPDs)
implement three-stage hybrid technology. The SPDs address over-voltage
transients with a primary Gas Discharge Tube (GDT) and secondary Silicon
Avalanche Diode (SAD) components. Over-current protection, e.g. sneak and fault
currents, are mitigated with solid-state resettable fuses — PTCs.

The Edco CX06-M, CX06-MI and CX06-MI-SBL SPDs are designed in accordance
with NFPA 780 (2004 edition) requirements, with up to 20 kA of surge current
capability. The Edco CX06-MI and CX06-MI-SBL models have an isolated ground
and is recommended for use at the camera-end.

CX06-M

General Technical Specifications

Operating Voltage 5 VDC

Clamping Voltage 6 VDC

Operating Current 0.15 A

Peak Surge Current 20 kA (8 x 20 μs)

Frequency Range 0 to 20 MHz

Insertion Loss < 0.1 dB at 20 MHz

Response Time < 0.5 ns

SPD Technology GDT, SAD, w/ Series PTC

Connection Type BNC, 50/75 Ohm

Operating Temperature -40°C to +85°C

Dimensions (in / mm) M = 1.5˝ H x 1.0˝ W x 3.25˝ L

[38.1 x 25.4 x 82.55 mm]

MI = 1.5˝ H x 1.0˝ W x 4.0˝ L

[38.1 x 25.4 x 101.6 mm]

SBL = 1.7˝ H x 1.4˝ W x 2.8˝ L

[43.18 x 35.56 x 71.12 mm]

Weight (oz / kg) M = 2.3 oz [0.07 kg]

MI = 3 oz [0.09 kg]

SBL = 3 oz [0.09 kg]

Certifications UL 497B Listed

CX06-MI

CX06-MI-SBL

Features

■ Sneak/fault current protection

■ Low insertion loss

■ Shielded case

■ Models with isolated ground

■ 5 year warranty

Ordering Information

*Other configurations available,
please contact factory.

Caution

Do not place this product in service on any signal line capable of supplying more than 150 mA continuously.

Attention

Ne pas placer ce produit dans le service sur une ligne de signal capable de fournir en permanence plus de
150 mA.

Head-End CX06-M

Camera-End

CX06-MI
CX06-MI-SBL

Installation Instructions

Read and Understand These Instructions:

These protectors are intended for indoor use on communication loop circuits which have been isolated from the Public Switch
Telephone Network.

The communication loop circuits shall not be exposed to accidental contact with the electric light or power conductors.
The protectors shall be installed per the applicable requirements of the National Electric Code, ANSI/NFPA 70.

Edco CX06-M: Head-End Equipment Protection

A. Connect the Edco CX06-M in line with the coaxial cable. The

side labeled “EQUIP” should be connected to the adjacent
head-end equipment.

B. Connect incoming coaxial cable to the side of the Edco

CX06-M labeled “CABLE”.

C. Connect a ground wire (10-12 AWG) between the Edco

CX06-M ground terminal and the AC power ground of
head-end equipment. Keep this wire as short and straight
as possible.

Only qualified personnel should install or
service this system. Electrical safety pre­cautions must be followed when installing
or servicing this equipment. To prevent risk
of electrical shock, turn off and lock out all
power sources to the unit before making
electrical connections or servicing.

DANGER!

V

Edco CX06-MI and CX06-MI-SBL: Camera-End Protection

A. Connect the Edco CX06-MI or -SBL in line with the coaxial

cable. The side labeled “EQUIP” should be connected to the
adjacent camera.

B. Connect incoming coaxial cable to the side of the Edco

CX06-MI or -SBL labeled “CABLE”.

C. Connect a ground wire (10-12 AWG) between the Edco

CX06-MI or -SBL ground terminal and either the AC power
ground or equipment building ground at the camera
location. Keep this wire as short and straight as possible.

Head-End

Equipment

(Keep ground wire

as short as possible)

CX06-M or

RM-CX06-16R

To AC Power Ground

Seulement le personnel qualifié doit installer
ou maintenir ce systéme. Des précautions
de sécurité en électricité doivent être suivis
lors de l’installation ou de la maintenance
de cet equipement. Pour eviter tout risque
de choc électrique, débranchez et verouiller
toutes les sources d’alimentation de cet
equipement avant de.

CX06-MI or

CX06-MI-SBL

(Keep ground wire

as short as possible)

Camera-End

Equipment

To AC Power Ground

or Building Ground

Emerson Network Power Contact information

Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: [phone]
T: [phone]
F: [phone]
E: [e-mail]

IO-50107 5/14 Rev. 5 Printed in USA

While every precaution has been taken to ensure accuracy and completeness herein, Emerson Network Power Surge Protection assumes no responsibility, and disclaims all liability, for damages
resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

Emerson Network Power, the Emerson Network Power logo and Edco are trademarks

www.EmersonNetworkPower.com/Surge

and service marks of Emerson Electric Co. ©2014 Emerson Electric Co.