Emerson CORNERSTONE CF1AB01, CORNERSTONE CF1ORB01, CORNERSTONE CF1PW01, CORNERSTONE CF1WB01 Owner's Manual
®
Part No. F40BP73270000 Form No. BP7327
Revision: 130605 U.L. Model No.: CF1
READ AND SAVE THESE INSTRUCTIONS
CORNERSTONE
®
Series
Ceiling Fan Owner's Manual
Model Numbers
CF1AB01 - Antique Brass
CF1ORB01 - Oil Rubbed Bronze
CF1PW01 - Pewter
CF1WB01 - Weathered Bronze
Net Weight: 27.0 Lbs.
1-800-654-3545
www.emersonfans.com
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
TM
1
9
8
5
TM
2
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2011” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
U.L. Model No.: CF1
READ AND SAVE THESE INSTRUCTIONS
Unpacking Instructions
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF1
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
WARNING
!
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
NOTE: Before discarding packaging material, be
certain all parts have been removed.
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the top of the motor facing up.
The upper foam pad serves as a holder for the fan
during the first stages of assembly.
PACKAGE CONTENTS
Part Description Quantity
A Fan Motor & Housing Assembly 1
B Motor Cover 1
C Ceiling Cover 1
D Ceiling Cover Trim 1
E Fan Blade Flanges (14°) 4
F Fan Blade Flanges (20°) 2
G Hanger Bracket 1
H Hanger Ball/Downrod Assembly 1
I 18” Downrod 1
J Downrod Trim 1
K Decorative Bulb 1
L Upper Cover Trim 1
M Lower Trim Assembly 1
HARDWARE CONTENTS
Part Description Quantity
1 Threaded Studs, #8-32 x 1” 2
2 Threaded Studs, #8-32 x 1-1/4” 2
3 Knurled Knobs, #8-32 4
4 Lockwashers, External Tooth #8 4
5 Wire Connectors 5
6 Clevis Pin 1
7 Hairpin Clip 1
8 #10-32 x 5/8” Oval Head Screws 9
9 #10-32 x 3/8” Pan Head Screws 21
10 Flat Washers 21
11 #8-32 x 1/2” Screws 7
12 Setscrew 1
13 Setscrew Wrench 1
14 Pull Chain Pendant & Coupling 1
A
B
C
D
I
J
K
E
F
G
H
L
M
1
6
7
11
12 13
8
423 5
910
14
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 10). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver
One wire stripper
One stepladder
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length
Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
4
U.L. Model No.: CF1
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
Your Cornerstone®ceiling fan comes with two sets of blade flanges. One set (consisting of two flanges)
allows you to use your fan with two blades, as the original 1895 Ceiling Fan was configured. The other set
(consisting of four flanges) allows you to use your fan with four blades. Both sets of flanges, and the fan
blades you selected, are patterned after the original 1895 Ceiling Fan. If your ceiling is nine feet or higher, you
may use the 18-inch downrod, along with the downrod trim and decorative bulb, to further enhance the 1895
ceiling fan look.
Ceiling Fan Assembly
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
U.L. Model No.: CF1
Figure 1
Figure 2
Figure 3
1. Remove the fan motor and housing assembly from
styrofoam packaging and position it so that the top of
the motor is facing you.
2.Remove the hanger ball from the downrod by
loosening the setscrew in the hanger ball until the ball
falls freely down the downrod (Figure 1). Remove the
pin from the downrod, then remove the hanger ball.
Retain the pin and hanger ball for reinstallation in
Step 9.
3. Separate, untwist and unkink the three motor leads.
Route the motor leads through the downrod and seat
the downrod in the motor coupling (Figure 2).
NOTE: If your ceiling height is nine feet or higher,
you may use the 18-inch downrod, along with the
downrod trim and decorative bulb. If your ceiling
height is between eight and nine feet, you must use
the shorter 4-1/2” downrod.
4. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin and
secure with the hairpin clip (Figure 3). (Pin and clip
are supplied in loose parts bag.) The clevis pin must
go through the holes in the motor coupling and the
holes in the downrod. Push the straight leg of the
hairpin clip through the hole near the end of the
clevis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from
working loose. Pull up on the downrod to make sure
the clevis pin is properly installed.
5. Install the setscrew (supplied) in the motor
coupling (Figure 3). While pulling up on the downrod,
tighten the setscrew using the setscrew wrench
(supplied).
NOTE: The setscrew must be properly installed as
described above, or fan wobble could result.
It is critical that the clevis pin in the motor coupler is
properly installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are properly
installed (as shown in Figure 3) could result in the fan
falling.
WARNING
!
PIN
HANGER BALL
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING
WHITE LEAD
CONNECTED
BROWN LEADS
HAIRPIN
CLIP
CONNECTED
RED LEADS
SETSCREW
DOWNROD
SETSCREW
CLEVIS PIN
DOWNROD
CLEVIS PIN
MOTOR
COUPLING
MOTOR LEADS
(BLACK, WHITE,
AND BLUE)
FAN MOTOR AND
HOUSING ASSEMBLY
DOWNROD
SETSCREW
WRENCH
6. Screw two 1” threaded studs (supplied) into the
motor (Figure 4). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until the
threaded studs protrude; install two lockwashers and
knurled knobs (supplied) to secure the cover.
NOTE: Make sure the connected red leads, the
connected brown leads, and the white lead are
completely inside the motor cover and not pinched
between the motor cover and the motor.
7. If you have installed the 18” downrod, install the
downrod trim and decorative bulb as follows (Figure
5). Slide the decorative trim (grommet-end first) over
the downrod and seat the grommet firmly against the
motor cover. Then slide the decora-tive bulb
(oriented as shown) over the down-rod, being certain
that the downrod trim seats in the bottom grommet of
the decorative bulb.
8. Position the ceiling cover trim and the ceiling cover
over the downrod. Be sure the cover is oriented
correctly, with the large opening at the top
(Figure 5).
9. Reinstall the hanger ball on the downrod (Figure 6)
as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod. Install the pin through the holes at top of
the downrod and slide the hanger ball up the
downrod, aligning the ball so the pin is captured in
the groove in the top of the hanger ball. Pull the
hanger ball up tight against the pin and securely
tighten the setscrew in the hanger ball. A loose
setscrew could create fan wobble.
Figure 4
Figure 6
Figure 5
6
U.L. Model No.: CF1
Ceiling Fan Assembly (continued)
KNURLED
KNOB
LOCKWASHER
DECORATIVE
BULB
GROMMET
MOTOR COVER
1"
THREADED
STUD
7/8"
MOTOR
18" DOWNROD
GROMMET
DOWNROD
TRIM
GROMMET
MOTOR COVER
PIN
HANGER BALL
DOWNROD
CEILING
COVER
Loading...