Emerson COOL MATE XLH260 Operating Instructions Manual

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 1/15

Temperature and Humidity controller

XLH260

XLH260XLH260

XLH260

CCCCOOL

OOL OOL

OOL M

MM

MATE

ATEATE

ATE

Operating instructions

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 2/15

CCCCOOL

OOLOOL

OOLM

MM

MATE

ATE ATE

ATE

XLH260

XLH260XLH260

XLH260

INDICE

1. GENERAL WARNINGS_________________________________________________________ 3

2. GENERAL DESCRIPTION ______________________________________________________ 3

3. TEMPERATURE REGULATION__________________________________________________ 3

4. HUMIDITY REGULATION_______________________________________________________ 3

5. FA NS ______________________________________________________________________ 4

6. THE DISPLAY ________________________________________________________________ 5

7. PARAMETER LIST ____________________________________________________________ 7

8. DIGITAL INPUT_______________________________________________________________ 9

9. INSTALLATION AND MOUNTING _______________________________________________ 10

10. DIMENSIONS _______________________________________________________________ 12

11. ELECTRICAL CONNECTIONS__________________________________________________ 12

12. HOW TO USE THE HOT KEY __________________________________________________ 12

13. ALARM SIGNALLING _________________________________________________________ 13

10. TECHNICAL DATA ___________________________________________________________ 13

14. XLH260 CONNECTIONS ______________________________________________________ 14

15. DEFAULT SETTING VALUES __________________________________________________ 14

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 3/15

1. GENERAL WARNINGS

1.1 PLEASE READ BEFORE USING THIS MANUAL

• This manual is part of the product and should be kept near the instrument for easy and quick reference.

• The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device.

• Check the application limits before proceeding.

1.2

SAFETY PRECAUTIONS

• Check the supply voltage is correct before connecting the instrument.

• Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high

atmospheric humidity to prevent formation of condensation

• Warning: disconnect all electrical connections before any kind of maintenance.

• Fit the probe where it is not accessible by the End User. The instrument must not be opened.

• In case of failure or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see address) with a detailed description of the

fault.

• Consider the maximum current which can be applied to each relay (see Technical Data).

• Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining.

• In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with inductive loads could be useful.

2. GENERAL DESCRIPTION

The XLH260 is microprocessor controller, suitable for applications on medium or low temperature refrigerating units. It control both humidity and
temperature. It has 6 output relays to control compressor, heating elements, defrost, fan de-humidifier and humidifier. It has 2 NTC inputs one for
thermostat the other one for defrost. It’s also present an 4÷20mA input for humidity. There is one digital input (free contact) configurable by
parameter. An output allows the user to program the parameter list with the “Hot Key”.

3. TEMPERATURE REGULATION

The temperature regulation is performed through neutral zone using compressor and heater output relays.

Set point

OFF

ON

• Heating output: CUT IN is “SET TEMP- dbt”, CUT OUT is when the temperature reaches the set point.

• Compressor output: CUT IN is “ SET TEMP + dbt”, CUT OUT is when the temperature reaches the set point.

3.1 DEFROST

Two defrost modes are available through the “tdF” parameter: defrost with electrical heater or hot gas. The defrost interval is controlled by means of
parameter “EdF”: (EdF=in) the defrost is made every “IdF” time, (EdF=Sd) the interval “IdF” is calculate through Smart Defrost algorithm (only when
the compressor is ON). To disable the defrost set the MdF parameter to zero

Humidity regulation during a defrost depends on the Hud parameter. With Hud=no humidity regulation is disabled. With Hud=yES humidity
regulation is performed also during a defrost.

4. HUMIDITY REGULATION

The humidity regulation is performed through neutral zone, by humidifying dehumidifying actions. Humidity control can be disabled setting the SET
%RH to “nu” value. In this case only the temperature control is perform.

4.1 HUMIDIFYING ACTION

The humidifying action is done enabling the humidifier relay when the humidity is lower than the “SET %RH-dbH” value. The relay is switch off when
humidity reaches the set values.

4.2 DEHUMIDIFYING ACTION WITHOUT DEHUMIDIFIER RELAY (OA1 DIFFERENT FROM DEH) – STANDARD CONFIGURATION

In this case the dehumidifying action is performed by setting the following parameters in this way:

tHu = cH kind of dehumidifying by means of heating and compressor relays
oA1 different from dEH:

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 4/15

The heating and compressor outputs are activated together when humidity is higher than SET %RH+dbH value. Outputs are disabled when humidity
comes back to the SET %RH value.

4.2.1 Relation between cooling, heating and dehumidifying

1. If is simultaneously present a request of cooling (temp>SET TEMP+dbt) and dehumidifying (RH > SET %RH+dbH): the cooling action has the

priority over the dehumidifying action: only the compressor relay is energised till the SET TEMP is reached at this point also the heating relay
is enabled.

2. If is simultaneously present a request of heating (temp< SET TEMP-dbt) and dehumidifying (RH > SET %RH+dbH): the dehumidifying action

has the priority over the heating action: both the compressor and the heating relays are energised till the humidity set is reached at this point
only the heating relay is enabled.

4.3 DEHUMIDIFYING ACTION WITH DEHUMIDIFIER RELAY (OA1 = DEH)
The configurable relay is used, setting the parameter oA1 =dEH.

NOTE: the LIGHT button is not more available;

Two kinds of de-humidifying are available:

4.3.1 Dehumidifying action with ONLY de-humidifier relay

By setting the parameter tHu = db the de-humidifying action is performed by enabling the de-humidifier relay when the humidity is higher than SET
%RH + dbH.
The relay is switch off when humidity comes back to the SET %RH value.

4.3.2 Dehumidifying action with de-humidifier and compressor relays

By setting the parameter tHu = cHu the de-humidifying action is performed by enabling the de-humidifier and compressor relays together. when the
humidity is higher than SET %RH + dbH.
The relays are switched off when humidity comes back to the SET %RH value.

If is simultaneously present a request of cooling (temp>SET TEMP+dbt) and dehumidifying (RH > SET %RH+dbH): the cooling action has the priority
over the dehumidifying action: only the compressor relay is energised till the SET TEMP is reached at this point also the de-humidifier is enabled.

5. FA NS

The fan control mode is selected by means of the “FnC” parameter:
FnC=C-n fans will switch ON and OFF with the compressor and not run during defrost:;
FnC= O-n fans will run continuously, but not during defrost
FnC=C-y fans will switch ON and OFF with the compressor and run during defrost;
FnC=O-y fans will run continuously also during defrost

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 5/15

6. THE DISPLAY

C

F

SET SET

%RH

To display and modify target temperature set point. (SET TEMP)

To display and modify target humidity set point (SET %RH); in programming mode it selects a parameter or confirm an operation.

In programming mode it browses the parameter codes or increases the displayed value.

To start a manual defrost: hold it pressed for at least 3s.
In programming mode it browses the parameter codes or decreases the displayed value.

Switch ON and OFF the light, if present (oA1=lig)

Switch ON and OFF the instrument.

KEY COMBINATIONS

+

To lock and unlock the keyboard

+

To enter the programming mode.

+

To exit the programming mode.

6.1 ICONS AND SYMBOLS

Each LED function is described in the following table.

LED MODE FUNCTION

ON

- Instrument in stand by.

- In “Pr2” indicates that the parameter is also present in “Pr1”.

°C

ON °C

°C

FLASHING If measurement unit is °C, it flashing on programming mode

°F

ON °F

°F

FLASHING If measurement unit is °F, it flashing on programming mode

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 6/15

LED MODE FUNCTION

ON The compressor is running

FLASHING Anti-short cycle delay enabled

ON The defrost is enabled

FLASHING Drip time in progress

ON Heating enabled

(temp)

FLASHING Temperature Set programming phase

ON ALARM signal

ON Fan is running

ON The light is on

ON RH%

ON Dehumidifying enabled

ON Humidifying enabled

(umid)

FLASHING Humidity Set programming phase

6.2 HOW TO SEE AND MODIFY THE SET POINT (TEMPERATURE AND HUMIDITY)

OR

1. Push and immediately release the SET key: the display will show the Set point value and the correspondent set icon starts

flashing;

2. To change the Set value push the o

o o

o or nnnn arrows within 10s.

3. To memorise the new set point value push the SET key again or wait 10s.

6.3 TO START A MANUAL DEFROST

1. Push the DOWN key for more than 2 seconds and a manual defrost will start.

6.4 TO ENTER IN PARAMETERS LIST “PR1”

To enter the parameter list “Pr1” (user accessible parameters) operate as follows:

+

1. Enter the Programming mode by pressing the SET %RH+ n

n n

n for few seconds. (°C or °F icon start flashing)

2. The instrument will show the first parameter present in “Pr1”

6.5 TO ENTER IN PARAMETERS LIST “PR2”

To access parameters in “Pr2”:

1. Enter the “Pr1” level.

2. Select “Pr2” parameter and press the “ SET %RH ” key.

3. The “PAS” flashing message is displayed, shortly followed by “0 - -” with a flashing zero.

4. Use oooo or nnnn to input the security code in the flashing digit; confirm the figure by pressing “ SET %RH ”.

The security code is “321“.

5. If the security code is correct the access to “Pr2” is enabled by pressing “ SET %RH ” on the last digit.

Another possibility is the following: after switching ON the instrument the user can push SET %RH + nnnn keys within 30 seconds.

NOTE: each parameter in “Pr2” can be removed or put into “Pr1” (user level) by pressing SET %RH + nnnn. When a parameter is present in “Pr1”

icon is on.

6.6 TO CHANGE PARAMETER VALUES

1. Enter the Programming mode.

2. Select the required parameter with oooo or nnnn.

3. Press the “ SET %RH ” key to display its value (°C or °F icon start blinking).

4. Use oooo or nnnn to change its value.

5. Press “ SET %RH ” to store the new value and move to the following parameter.
To exit: Press SET %RH + UP or wait 15s without pressing a key.

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 7/15

NOTE: the new programming is stored even when the procedure is exited by waiting the time-out.

6.7 HOW TO LOCK THE KEYBOARD

AND

1. Keep the o

oo

o and nnnn keys pressed together for more than 3 s the oooo and nnnn keys.

2. The “POF” message will be displayed and the keyboard is locked. At this point it is only possible the viewing of the set point or the

MAX o Min temperature stored and to switch ON and OFF the light, the auxiliary output and the instrument.

TO UNLOCK THE KEYBOARD

Keep the oooo and nnnn keys pressed together for more than 3s.

6.8 ON/OFF FUNCTION

By pushing the ON/OFF key, the instrument shows “OFF” for 5 sec. and the ON/OFF LED is switched ON.
During the OFF status, all the relays are switched OFF and the regulations are stopped;

N.B. During the OFF status the icon is lighted.

7. PARAMETER LIST

REGULATION

dbt half dead band width for temperature: (0,1÷25,5°C; 1÷45°F) this band is place below and above the temperature set point (SET TEMP).

The compressor is enabled when the temperature increases and reaches the SET TEMP + dbt value. It is turned off when it comes back to
the SET TEMP. The heating output is enabled when temperature is less than SET TEMP -dbt value and disabled when the SET TEMP is
reached.

dbH half dead band width for humidity: (0,5÷25,5RH) this band is place below and above the humidity set point (SET %RH). The

dehumidifying action is enabled when the humidity increases and reaches the SET %RH + dbH value. It is stopped when it comes back to
the SET %RH. The humidifying output is enabled when humidity is less than SET %RH -dbH value and disabled when the SET %RH is
reached.

LS Minimum temperature set point limit: (-50,0°C÷

÷÷

÷SET; -58°F÷SET) Sets the minimum acceptable value for the set point.

US Maximum temperature set point limit: (SET÷

÷÷

÷110°C; SET÷230°F) Set the maximum acceptable value for set point.

OdS Outputs activation delay at start up: (0÷255 min) This function is enabled at the initial start up of the instrument and inhibits any output

activation for the period of time set in the parameter. (Light can work)

AC Anti-short cycle delay: (0÷30 min) interval between the compressor stop and the following restart.
tHu Kind of de-humidifying: db: only with de-humidifier relay (oA1= dEH); cHu with de-humidifier and compressor relay (oA1= dEH); c-H:

without de-humidifier relay, by means of compressor and heating relays (oA1≠ dEH).

LSH Minimum humidity set point limit: (Lci ÷ Set H) Sets the minimum acceptable value for the humidity set point.
USH Maximum humidity set point limit: (Set H ÷ uci) Set the maximum acceptable value for humidity set point.

DISPLAY
CF Measurement unit: °C= Celsius; °F= Fahrenheit

rES Resolution (for °C): allows decimal point display. dE = 0,1°C; in = 1 °C
rEH Resolution for RH%: in = integer; Hd= half digit.

DEFROST
tdF Defrost type: rE = electrical heater (Compressor OFF); in = hot gas (Compressor and defrost relays ON)

EdF Defrost mode: in = interval mode. The defrost starts when the time “Idf” is expired. Sd =Smartfrost mode. The time IdF (interval

between defrosts) is increased only when the compressor is running (even non consecutively).

SdF Set point for SMARTFROST: (-30÷30 °C/ -22÷86 °F) evaporator temperature which allows the IdF counting (interval between defrosts) in

SMARTFROST mode.

dtE Defrost termination temperature: (-50,0÷110,0°C; -58÷230°F) (Enabled only when the evaporator probe is present) sets the temperature

measured by the evaporator probe which causes the end of defrost.

IdF Interval between defrosts: (1÷120h) Determines the time interval between the beginning of two defrost cycles.
MdF Duration of defrost: (0÷255 min) When P2P = n, no evaporator probe, it sets the defrost duration, when P2P = y, defrost end based on

temperature, it sets the maximum length for defrost.

dFd Display during defrost: rt = real temperature; it = temperature reading at the defrost start; Set = set point; dEF = “dEF” label; dEG =

“dEG” label;

dAd Defrost display time out: (0÷255 min) Sets the maximum time between the end of defrost and the restarting of the real room temperature

display.

Fdt Drain down time: (0÷60 min.) time interval between reaching defrost termination temperature and the restoring of the control’s normal

operation. This time allows the evaporator to eliminate water drops that might have formed due to defrost.

dPO First defrost after start-up: y = Immediately; n = after the IdF time
Hud Humidity control during defrost: no: the humidity control is stopped during the defrost; yES the humidity control works also during the

defrost.

FANS

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 8/15

FnC Fan operating mode: C-n = running when a load is on, OFF during the defrost; C-y = running when a load is on, ON during the defrost; O-n

= continuous mode, OFF during the defrost; O-y = continuous mode, ON during the defrost;

TEMPERATURE ALARMS
ALC Temperature alarm configuration: rE = High and Low alarms related to Set Point; Ab = High and low alarms related to the absolute

temperature.

ALL Low temperature alarm setting: ALC = rE , 0 ÷

÷÷

÷ 50 °C or 90°F

ALC = Ab , - 50°C or -58°F ÷

÷÷

÷ ALU

when this temperature is reached and after the ALd delay time, the LA alarm is enabled,.
ALU High temperature alarm setting: ALC= rE, 0 ÷

÷÷

÷ 50°C or 90°F

ALC= Ab, ALL ÷ 110°C or 230°F
when this temperature is reached and after the ALd delay time the HA alarm is enabled.

ALH Temperature alarm recovery differential: (0,1÷25,5°C; 1÷45°F) Intervention differential for recovery of temperature alarm.
ALd Temperature alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.
dAO Delay of temperature alarm at start-up: (0min÷23h 50min) time interval between the detection of the temperature alarm condition after the

instrument power on and the alarm signalling.

EdA Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the temperature alarm condition at the end of defrost

and the alarm signalling.

dot Delay of temperature alarm after closing the door : (0÷255 min) Time delay to signal the temperature alarm condition after closing the

door.

HUMIDITY ALARMS
AHC Humidity alarm configuration: rE = High and Low alarms related to humidity Set Point; Ab = High and low alarms related to the “absolute”

humidity.

AHL Low humidity alarm setting: (with AHC = rE: 0 ÷ 50. With AHC = Ab: Lci ÷ AHu)
when this humidity is reached and after the AHd delay time, the HLA alarm is enabled,.
AHu High humidity alarm setting: (with AHC = rE: 0÷50°C. with AHC = Ab: AHL ÷ uci
when this humidity is reached and after the AHd delay time the HHA alarm is enabled.

AHH Humidity alarm recovery differential: (0.5÷20.0) Intervention differential for recovery of humidity alarm.
AHd Humidity alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.
dHo Delay of humidity alarm at start-up: (0min÷23h 50min) time interval between the detection of the humidity alarm condition after the

instrument power on and the alarm signalling.

doH Alarm delay at the end of defrost: (0÷255 min) Time interval between the detection of the humidity alarm condition at the end of defrost

and the alarm signalling.

doA Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and its alarm signalling: the flashing message

“dA” is displayed.

nPS Pressure switch number: (0 ÷15) Number of activation of the pressure switch, during the “did” interval, before signalling the alarm event

(I2F= PAL). If the nPS activation in the “did” time is reached, switch off and on the instrument to restart normal regulation.

PROBE INPUTS
Ot Thermostat probe calibration: (-12.0÷

÷÷

÷12.0°C/ -21÷÷÷÷21°F) allows to adjust possible offset of the thermostat probe.

OE Evaporator probe calibration: (-12.0÷

÷÷

÷12.0°C/ -21÷÷÷÷21°F) allows to adjust possible offsets of the evaporator probe.

O3 Humidity probe calibration: (-10÷÷÷÷10 RH) allows to adjust possible offsets of the humidity probe.
P2P Evaporator probe presence: n= not present: the defrost stops only by time; y= present: the defrost stops by temperature and time.
P3P Humidity probe presence: n= not present; y= present.
LCI Readout with 4 mA : (-999 ÷ 999). Adjustment of read out corresponding to 4mA signal.
UCI Readout with 20 mA : (-999 ÷ 999). Adjustment of read out corresponding to 20mA signal.

DIGITAL INPUTS
i1P Configurable digital input polarity: CL : the digital input is activated by closing the contact; OP : the digital input is activated by opening

the contact;

i2P Door switch digital input polarity: CL : the digital input is activated by closing the contact; OP : the digital input is activated by opening the

contact;

i1F Digital input operating mode: configure the digital input function: EAL = generic alarm; bAL = serious alarm mode; PAL = Pressure

switch; Ht = heating relay safety; dor = door switch

odc Outputs status when open door: on = normal; Fan = Fan OFF; oFF = all the loads off
rrd Outputs restarting after doA alarm: no = outputs not affected by the doA alarm; yES = outputs restart with the doA alarm;
did Time interval/delay for digital input alarm:(0÷255 min.) Time interval to calculate the number of the pressure switch activation when

I1F=PAL. If I1F=EAL or bAL (external alarms), “did” parameter defines the time delay between the detection and the successive signalling of
alarms.

OTHER
oA1 Light relay configuration: ALr = alarm; dEH = dehumidifier; onF = on/off relay: close with instrument on, open with instrument off; Lig =

light, ESt, dEF not select

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 9/15

Adt RS485 serial address, temperature section (0÷247) it identifies the temperature section of the instrument within a control or supervising

system.

NOTE: XJ500: set Adt different from AdH. X-WEB300/3000: set Adt equal to AdH.

AdH RS485 serial address, humidity section (0÷247) it identifies the humidity section of the instrument within a control or supervising system.
Ptb Parameter table: (read only) it shows the original code of the dIXEL parameter map.
rEL Software release: (read only) Software version of the microprocessor.
Prd Probes display: (read only) display the temperature values of the evaporator probe Pb2.
Pr2 Access to the protected parameter list (read only).

8. DIGITAL INPUT

One digital input is present configurable by user by means of the i1F parameter according to the following descriptions.

8.1 DIGITAL INPUT 1 (5-6): DOOR SWITCH

It signals the door status and the corresponding relay output status through the “odc” parameter: no = normal (any change); Fan = Fan OFF; oFF =
all the loads are switched off.

Since the door is opened, after the delay time set through parameter “dOA”, the alarm output is enabled and the display shows the message “dA”.
The status of loads depends on the “rrd” parameter:

with rrd=no outputs are not affected by the doA alarm;

with rrd=yES = outputs restart with the doA alarm;
The alarm stops as soon as the external digital input is disabled again. During this time and then for the delay “dot” and “doH” after closing the door,
the temperature and humidity alarms are disabled.

8.2 DIGITAL INPUT 2 (3-4): GENERIC ALARM (I1F = EAL)

As soon as the digital input is activated the unit will wait for “did” time delay before signalling the “EAL” alarm message. The outputs status don’t
change. The alarm stops just after the digital input is de-activated.

8.3 DIGITAL INPUT 2 (3-4): SERIOUS ALARM MODE (I1F = BAL)

When the digital input is activated, the unit will wait for “did” delay before signalling the “bAL” alarm message. The relay outputs are switched OFF.
The alarm will stop as soon as the digital input is de-activated.

8.4 DIGITAL INPUT 2 (3-4): PRESSURE SWITCH (I1F = PAL)

If during the interval time set by “did” parameter, the pressure switch has reached the number of activation of the “nPS” parameter, the “PAL”
pressure alarm message will be displayed. The compressor and the regulation are stopped. When the digital input is ON the compressor is always
OFF. If the nPS activation in the did time is reached, switch off and on the instrument to restart normal regulation.

8.5 DIGITAL INPUT 2 (3-4): HEATING RELAY SAFETY (i1F=Ht)

With i1F=Ht as soon as the digital input is activated for “did” time heating relay is disabled. The alarm will stop as soon as the digital input is de­activated.

8.6 DIGITAL INPUTS POLARITY

The digital input polarity depends on the “i1P” and “i2P”parameters. CL : the digital input is activated by closing the contact. OP : the digital input is
activated by opening the contact

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 10/15

9. INSTALLATION AND MOUNTING

The temperature range allowed for correct operation is 0 - 60 °C. Avoid places subject to strong vibrations, corrosive gases, excessive dirt or
humidity. The same recommendations apply to probes. Let the air circulate by the cooling holes. Thanks to the case, XLH260 model can be panel or
wall mounted. See the following instructions for details.

A B

C

D

E

G

F

FIG. 1

A

B

C

G

F

D

FIG. 2

87

230

M

A

X

3

7

210

130

120

M
A

X

2
8

H

I

FIG. 3

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 11/15

A

Fig. 6

2

0

0

6

1

0

0

172

1

0

6

.

4

4

°

190

18

Fig. 4

2

0

0

1

9

2

.

5

1

8

5

61

12

6

0

0
4

11

14.5

22.5

29.5

160.55

167.5

175.5

179

186

190

R
5

8.5

8

.

5

1

0

6

.

4

4

°

R

5

Fig. 5

9.1 WALL MOUNTING

1. Unscrew the 4 frontal screws (Fig. 1, A, B, F, G) and remove the cover (Fig. 1, C).

2. Unscrew the 2 screws (Fig. 1, D, E) that keep connected the frontal and lower parts of Cool Mate and separate the 2 parts.

3. Make the proper holes for cablepresses or pipepresses using the centres signed in the bottom cover of the Cool Mate, (Fig. 3, H, I, ). Then

make 3 holes in the wall, as indicated in (Fig. 3, L, M, N), to fix the Cool Mate

4. Fix the cablepresses and the pipepresses..

5. Insert the wall-nugs, contained in the kit, into the holes made in the wall. Then use the o-rings and fix the back part of the Cool Mate (Fig. 3, L,

M, N) by means of the 3 screws to the wall itself.

6. Insert the wiring cables in cablepresses or in the pipepresses.

7. Mount the frontal part using the previous 4 screws Fig. 1, D, E, F, G. (do not press excessively in order to avoid plastic deformation).

8. After connecting the wires to the terminal blocks close the cover (Fig. 2, c) and fix it by the screws.

9.2 PANEL MOUNTING

1. Make a hole in the panel with dimensions described in Fig. 4 (simplified) or Fig. 5 (completed)

2. Unscrew the 4 frontal screws (Fig. 1, A, B, F, G) and remove the cover (Fig. 1, C).

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 12/15

3. Unscrew the 2 screws (Fig. 1, D, E) that keep connected the frontal and lower parts of Cool Mate and separate the 2 parts.

4. Cut from the back part of the Cool Mate the teeth indicated in Fig. 6, A.

5. Make the proper holes for cablepresses or pipepresses using the centres signed in the bottom cover of the Cool Mate, (Fig. 3, H, I, ).

6. Fix the cablepresses and the pipepresses..

7. Insert the wiring cables in cablepresses or in the pipepresses.

8. Join the back and frontal parts, with the panel in the middle, and fix them screwing the 4 screws taken previously away (dimensions 4x35

mm), in the holes of Fig. 1, A, B, D, E. Maximum panel thickness: 6mm.

9. After connecting the wires to the terminal blocks close the cover (Fig. 2, c) and fix it by the screws.

10. DIMENSIONS

210

87

2

3

0

11. ELECTRICAL CONNECTIONS

The instruments are provided with screw terminal block to connect cables with a cross section up to 2,5 mm2. Heat-resistant cables have to be used.
Before connecting cables make sure the power supply complies with the instrument’s requirements. Separate the probe cables from the power
supply cables, from the outputs and the power connections. Do not exceed the maximum current allowed on each relay, in case of heavier loads use
a suitable external relay.

11.1 PROBE CONNECTIONS

The probes shall be mounted with the bulb upwards to prevent damages due to casual liquid infiltration. It is recommended to place the thermostat
probe away from air streams to correctly measure the average room temperature.

12. HOW TO USE THE HOT KEY

12.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD)

1. Program one controller with the front keypad.

2. When the controller is ON, insert the “Hot key” and push oooo key; the "uPL" message appears followed a by flashing “End”

3. Push “SET” key and the End will stop flashing.

4. Turn OFF the instrument remove the “Hot Key”, then turn it ON again.

NOTE: the “Err” message is displayed for failed programming. In this case push again oooo key if you want to restart the upload again or remove the
“Hot key” to abort the operation.

12.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)

1. Turn OFF the instrument.

2. Insert a programmed “Hot Key” into the 5 PIN receptacle and then turn the Controller ON.

3. Automatically the parameter list of the “Hot Key” is downloaded into the Controller memory, the “doL” message is blinking followed a by

flashing “End”.

4. After 10 seconds the instrument will restart working with the new parameters.

5. Remove the “Hot Key”..

NOTE the message “Err” is displayed for failed programming. In this case turn the unit off and then on if you want to restart the download again or
remove the “Hot key” to abort the operation.

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 13/15

13. ALARM SIGNALLING

Message Cause Outputs

“P1” Thermostat probe failure Compressor and heating outputs off
“P2” Evaporator probe failure Defrost and by time
“P3” Humidity probe failure Humidity regulation off
“HA” High temperature alarm Outputs unchanged

“LA” Low temperature alarm Outputs unchanged
“HHA” High humidity alarm Outputs unchanged
“HLA” Low humidity alarm Outputs unchanged

“dA” Door switch alarm Outputs depending on the odC parameter

“EAL” External alarm Other outputs unchanged
“BAL” Serious external alarm Outputs OFF

“PAL” Pressure switch alarm Outputs OFF
The alarm message is displayed until the alarm condition recoveries.
All the alarm messages are showed alternating with the room temperature except for the “P1” which is flashing. To reset the “EE” alarm and restart
the normal functioning press any key, the “rSt” message is displayed for about 3s.

13.1 SILENCING BUZZER

Once the alarm signal is detected the buzzer, if present, can be silenced by pressing any key.

13.2 ALARM RECOVERY
Probe alarms : “P1” (probe1 faulty), “P2”, “P3”; they automatically stop 10s after the probe restarts normal operation. Check connections before

replacing the probe.

Temperature alarms “HA” and “LA” automatically stop as soon as the thermostat temperature returns to normal values or when the defrost starts.
Humidity alarms “HHA” and “LHA” automatically stop as soon as the humidity returns to normal values.
Door switch alarm “dA” stop as soon as the door is closed.
External alarms “EAL”, “BAL” stop as soon as the external digital input is disabled
Pressure switch alarm “PAL” alarm is recovered by switching OFF the instrument.

10. TECHNICAL DATA

Housing: self extinguishing ABS; Case: frontal 210x230 mm; depth 87mm; Mounting: See par. 9; Protection: IP65
Connections: Screw terminal block ≤ 2,5 mm2 wiring.
Power supply: 230Vac 50/60Hz ± 10% or 110Vac 50/60Hz ± 10%; Power absorption: 10VA max.
Display:3 digits, red LED, 30.5 mm high; 3 digits, yellow LED low.
Inputs: 2 NTC probes, one 4÷20mA input

Digital inputs : door switch and configurable, free voltage. Max. distance 10m

Relay outputs:

compressor: relay SPST 20(8) A, 250Vac;
defrost: relay SPDT 16(3) A, 250Vac;
fans: relay SPST 8(3) A, 250Vac;
heater control: relay SPST 20(8) A, 250Vac;
Humidifying: relay SPST 8(3) A, 250Vac;
Dehumidifying / Light: relay SPST 16(3) A, 250Vac

Other output :
Alarm buzzer (Standard)
Direct RS485 (optional)
Data storing: on the non-volatile memory (EEPROM).
Kind of action: 1B.; Pollution grade: normal; Software class: A.
Operating temperature: 0÷60 °C.; Storage temperature: -25÷60 °C.
Relative humidity: 20÷85% (no condensing)
Measuring and regulation range: NTC probe: -40÷110°C (-58÷230°F);
Resolution: 0,1 °C or 1°C or 1 °F (selectable).
Accuracy (ambient temp. 25°C): ±0,5 °C ±1 digit

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 14/15

14. XLH260 CONNECTIONS

1 2 3 4 5 6 7 8 9 101 1 12 13 14 151 6 17 18 19 20 21 222 3 24 25 26 2728 2930 31 33 34

Conf. Do or

Room

Evap.

HO T KEY

16A

250V~

16A

250V~8A250V~

20A 250V

16 FLA(96L RA)

20 A 250V

16 FLA(96L RA)

8A

250V

~

Supply

120/230V~

NLi ne

NC

Fa n

35 36

In

12V§ gnd

Input

4÷20mA

Heater Hum

L ight

De-

Hu m

Comp

Def

NC

RS 485

(optionaal)

15. DEFAULT SETTING VALUES

Label Value Menu Description Range

Set T

5.0 - - - Temperature Set Point LS ÷ uS ( nu = temperature regulation disabled )

Set H

50.0 - - - Humidity Set Point LSH ÷ uSH ( nu = humidity regulation disabled)

dbt

2.0 Pr1 Half dead band width for temperature 0.1°C o 1°F ÷ 25°C o 77°F

dbH

5.0 Pr1 Half dead band width for humidity 0.5 ÷ 50

LS

-40 Pr2 Minimum temperature set point limit -50.0°C o –58°F ÷ Set T

uS

110 Pr2 Maximum temperature set point limit Set T ÷ 110°C o 230°F

odS

1 Pr2 Outputs activation delay at start up 0 ÷ 250 min

Ac

1 Pr1 Anti-short cycle delay 0 ÷ 30 min

tHu

c-H Pr2 Humidity regulation

db = dehumidifier relay.; cHu = dehum+ compr.; c-H= without

dehum. relay

LSH

0.0 Pr2 Minimum humidity set point limit Lci ÷ Set H

uSH

100.0 Pr2 Maximum humidity set point limit Set H ÷ uci

cF

°C Pr2 Measurement unit °C ÷°F

rES

dE Pr2 Resolution (for °C): in = integer / dE = decimal

rEH

Hd Pr2 Resolution for RH%: in = integer / Hd = half digit

tdf

rE Pr2 Defrost type rE, rT, in

EdF

in Pr2 Defrost mode In, Sd

SdF

0 Pr2 Set point for SMART DEFROST -30 ÷ +30°C / -22÷+86°F

dtE

8 Pr2 Defrost termination temperature -50,0÷110°C/ -58÷230°F

idF

6 Pr1 Interval between defrosts 1 ÷ 120 h

MdF

20 Pr1 Duration of defrost 0 ÷ 250 min

dFd

it Pr2 Display during defrost rt / it / SEt / dEF / dEG

dAd

30 Pr2 Defrost display time out 0 ÷ 250 min

Fdt

0 Pr2 Draining time 0÷60 min.

dPo

no Pr2 First defrost after start up n ÷ y

Hud

no Pr2 Humidity control during defrost no; yES

Fnc

c-n Pr2 Fan operating mode c-n / c-Y / o-n / o-Y

ALc

Ab Pr2 Temperature alarm configuration rE = relative / Ab = absolute

ALL

-40.0 Pr1 Low temperature alarm setting 0°C ÷ 50.0°C / -50.0°C ÷ ALu

ALu

110 Pr1 High temperature alarm setting 0°C ÷ 50.0°C / ALL ÷ 110°C

ALH

1.0 Pr2 Temperature alarm recovery differential 0.1°C o 1°F ÷ 25°C o 77°F

ALd

15 Pr2 Temperature alarm delay 0 ÷ 250 min

dAo

1.3 Pr2 Delay of temperature alarm at start-up 0.0 ÷ 23.5 h

EdA

20 Pr2 Alarm delay at the end of defrost 0 ÷ 250 min

dot

20 Pr2

Delay of temperature alarm after closing the

door

0 ÷ 250 min

AHc

Ab Pr2 Humidity alarm configuration rE = relative / Ab = absolute

AHL

0.0 Pr1 Low humidity alarm setting 0 ÷ 50 / Lci ÷ AHu

AHu

100 Pr1 High humidity alarm setting 0 ÷ 50 / AHL ÷ uci

AHH

2.0 Pr2 Humidity alarm recovery differential 0.5 ÷ 25

AHd

15 Pr2 Humidity alarm delay 0 ÷ 250 min

dHo

1.3 Pr2 Delay of humidity alarm at start-up 0.0 ÷ 23.5 h

doH

20 Pr2 Alarm delay at the end of defrost 0 ÷ 250 min

nPS

20 Pr2 Pressure switch number 0÷15

dIXEL

dIXELdIXEL

dIXEL

Operating instructions

cod. 1592

cod. 1592cod. 1592

cod. 1592017400

017400017400

017400

1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 15/15

doA

0 Pr2 Open door alarm delay 0 ÷ 250 min ( 250 = nu )

ot

0.0 Pr1 Thermostat probe calibration -12.0 ÷ 12.0

oE

0.0 Pr2 Evaporator probe calibration -12.0 ÷ 12.0

o3

0.0 Pr1 Humidity probe calibration -10 ÷ 10

P2P

YES Pr2 Evaporator probe presence no = absent / YES = present

P3P

YES Pr2 Humidity probe presence no = absent / YES = present

Lci

0 Pr2 Readout with 4 mA -999 ÷ 999

uci

100 Pr2 Readout with 20 mA -999 ÷ 999

i1P

cL Pr2 Configurable digital input polarity cL =open / oP = close

i2P

cL Pr2 Door switch digital input polarity cL =open / oP = close

i1F

EAL Pr2 Digital input configuration dor / PAL / EAL / bAL / Ht

odc

FAn Pr2 Outputs status when open door on / Fan / oFF

rrd

YES Pr2 Outputs restarting after doA alarm no = no / YES = yes

did

5 Pr2 Digital input alarm delay 0÷255 min.

oA1 Lig Pr2 Light relay configuration:

ALr = alarm; dEH = dehumidifier; onF = on/off; Lig = light,

ESt, dEF not select

Adr

1 Pr2 Serial address 0÷247 num

Ptb

- Pr2 Parameter table - - -

rEL

1.0 Pr2 Software release - - -

Prd

-- Pr2 Probes display Pb1÷Pb3

Pr2

321 Pr1 Access to the protected parameter list - - -

dIXEL

dIXELdIXEL

dIXEL S.p.a.

Z.I. Via dell’Industria, 27 - 32010 Pieve d’Alpago (BL) ITALY
tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13

http://www.dixell.com E-mail: [e-mail]