Emerson CF787GBZ00, CF787ORB00, CF787AP00, CF787GES00, CF787BS00 User Manual
...
READ AND SAVE THESE INSTRUCTIONS
CARRERA GRANDE™ |
|
Ceiling Fan Owner's Manual |
|
Model Numbers |
|
CF787AW00 - Summer White |
|
CF787AP00 - Antique Pewter |
|
CF787BS00 - Brushed Steel |
|
CF787GBZ00 - Gilded Bronze |
|
CF787GES00 - Golden Espresso |
|
CF787ORB00 - Oil Rubbed Bronze |
|
Net Weight: 25.3 Lbs. |
54”, 60” or 72” Fan Blades |
Not Included |
|
Part No. F40BP73770001 |
Form No. BP7377-1 |
|
U.L. Model No.: CF787 |
!WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1.Read your owner’s manual carefully and keep it for future reference.
2.Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.
3.Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing.
4.Do not put anything into the fan blades while they are turning.
5.Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1.To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2.All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-1999” and Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
3.The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 50 lbs or less”, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
4.The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling.
5.The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
6.Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2 |
U.L. Model No.: CF787 |
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver |
One stepladder |
One wire stripper |
|
Three wire connectors (supplied) |
|
MATERIALS
Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of the following size:
Installed Wire Length |
Wire Size A.W.G. |
Up to 50 ft. |
14 |
50-100 ft. |
12 |
|
|
!WARNING
Before assembly your ceiling fan, refer to section on proper method of wiring your fan (page 7). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted.
!WARNING
Do not install or use fan if any part is damaged or missing. Call Toll-Free:
1-800-654-3545
!WARNING
This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage.
NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding.
2.Remove the fan assembly from the protective plastic bag. Place the fan assembly into the upper foam pad with the bottom of the motor facing up.
The upper foam pad serves as a holder for the fan during the first stages of assembly.
1.Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer to exploded view illustration.
a.Fan motor assembly
b.One switch housing assembly
c.One ceiling cover
d.Five blade flanges
e.One hanger ball/12” downrod assembly
f.One hanger bracket
g.One coupling cover
h.One loose parts bag containing:
1.Twenty-one M5 x 12mm washer head blade screws
2.One M4 x 12mm flat head screw
3.One M6 x 14mm pan head screew with lockwasher
4.One die-cast pendant
5.One pendant coupler
6.Three wire connectors
7.Two threaded studs
8.Two knurled knobs
9.Two lockwashers
10.One clevis pin
11.One hairpin clip
12.One balance kit
LOOSE PARTS
BAG 
FAN MOTOR
ASSEMBLY
BLADE FLANGES
|
SWITCH HOUSING |
|
ASSEMBLY |
|
HANGER BALL/ |
|
DOWNROD ASSEMBLY |
|
HANGER |
CEILING |
BRACKET |
COVER |
|
|
COUPLING |
|
COVER |
3 |
U.L. Model No.: CF787 |
Electrical Requirements
Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.
!WARNING
To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support of 50 lbs or less”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.
!WARNING
Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.
!WARNING
To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician.
How to Put Your Ceiling Fan Together
1.Rotate the motor hub to align the hub notch area over each of the five screws which is holding the shipping retainer to the motor assembly. One by one unscrew each screw and discard screw and shipping reatiner (Figure 1).
MOTOR HUB
REMOVE SHIPPING RETAINER
BY REMOVING 5 SCREWS
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
nd |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
tsA |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
oun |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
gM |
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
kin |
|
|
|
|
|
|
ra |
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
c |
|
|
|
|
|
|
|
|
. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
a |
|
|
|
|
|
|
|
|
|
aPa |
|
|||
|
|
|
|
|
|
|
|
|
|
rP . |
|
|
|
|
|
om |
|
lacion |
||||||||
|
|
|
|
|
|
|
|
|
e |
|
|
n |
|
|
|
|
G |
|
|
ta |
|
|||||
|
|
|
|
|
|
|
|
b |
|
|
tio |
|
|
|
De |
|
|
aIns |
|
|
||||||
|
|
|
|
|
|
|
|
b |
|
|
a |
|
|
|
s |
|
|
|
L |
|
|
|
||||
|
|
|
|
|
|
|
u |
|
ll |
|
|
rte |
|
|
De |
|
|
|
|
|
||||||
|
|
|
|
|
|
R ta |
|
|
o |
|
|
|
s |
|
|
|
|
|
|
|||||||
|
|
|
|
|
e |
|
s |
|
|
p |
|
|
|
te |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
v |
|
In |
|
|
o |
|
|
|
n |
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
o |
|
|
S |
|
|
|
A |
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
m |
e |
|
s |
|
|
s |
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
r |
|
o |
|
|
o |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
e |
fo |
|
L |
|
rL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
R |
|
|
e |
r |
|
a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
! |
|
|
B ita |
|
ir |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
E |
d |
u |
|
T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
T |
|
r |
|
|
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
O |
ca |
|
!Q e |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
N is |
|
A |
|
J |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
D |
|
T |
|
la |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
O |
|
|
a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
N |
|
|
b |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
m |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 1 
2.Mount blade flanges (supplied with fan) to fan blades (sold separately) using four M5 x 12mm washer head blade screws (supplied with fan) (Figure 2).
NOTE: Take care not to scratch fan housing when installing blades.
M5 x 12mm WASHER HEAD BLADE SCREW (4 per blade/flange)
FAN BLADE
BLADE FLANGE 
Figure 2
3.Loosely attach one blade/flange assembly to the motor hub by secureing the two M6 x 14mm captive pan head screws. Make sure the screws are NOT tightened (Figure 3). Repeat this procedure for other four blade assemblies.
!WARNING
To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
4 |
U.L. Model No.: CF787 |
Loading...