Emergi-Lite EF10D User Manual
Installation instructions
Parts List
1. Lamp head
2. Junction box screws (not provided)
3. Canopy
4. Toothed lock washer
5. Nut
6. Junction box (not provided)
Figure 1
Rotation
Tilt
Center of rotation
Parts List
1. Lamp head
2. Junction box screws (not provided)
3. Canopy
4. Lock washer
5. Nut
6. Junction box (not provided)
Figure 1
Rotation
Tilt
Center of rotation
Note: Lamp heads may already be attached to the canopy.
1. Determine the final position for the lamp head.
2. Look for the mark on the threaded portion of the swivel to
find the center of rotation for the lamp head.
3. Insert the flat surface from the swivel into the square hole on
the canopy ensuring that the center of rotation is as close as
possible to the final position. Secure the lamp head in place
with the lock washer and nut provided.
4. Adjust the lamp head into its final position.
5. Make the proper connections. The fixture is designed for 6,
12 or 24 VDC (see the lamp voltage indicated on the inside
surface of the canopy). Connect the lamp wires to the DC
supply wires.
6. Use the junction box screws to secure the canopy to the
junction box.
Adjust the lamp head:
Rotation: hold the lamp head and turn it to either side.
-Note: The lamp head can be rotated 150° to either side.
Tilting: hold the lamp head and tilt it up or down.
The lamp head uses a ratchet type mechanism that moves it in
10 degree increments (see fig. 1).
Remote heads – Installation instructions
Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com
Remote heads – Installation instructions
Installation instructions
Note: Lamp heads may already be attached to the canopy.
1. Determine the final position for the lamp head.
2. Look for the mark on the threaded portion of the swivel to
find the center of rotation for the lamp head.
3. Insert the flat surface from the swivel into the square hole on
the canopy ensuring that the center of rotation is as close as
possible to the final position. Secure the lamp head in place
with the lock washer and nut provided.
4. Adjust the lamp head into its final position.
5. Make the proper connections. The fixture is designed for 6,
12 or 24 VDC (see the lamp voltage indicated on the inside
surface of the canopy). Connect the lamp wires to the DC
supply wires.
6. Use the junction box screws to secure the canopy to the
junction box.
10/12 750.1106 Rev. B
1/1
Adjust the lamp head:
Rotation: hold the lamp head and turn it to either side.
-Note: The lamp head can be rotated 150° to either side.
Tilting: hold the lamp head and tilt it up or down.
The lamp head uses a ratchet type mechanism that moves it in
10 degree increments (see fig. 1).
Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com
10/12 750.1106 Rev. B
1/1
Installation instructions
1
2
3
4
5
6
7
8
Parts List
1. Lamp heads (2 or 3)
2. Canopy screws
3. Canopy
4. Lock washer
5. Nut
6. Junction box screws (not provided)
7. Spider plate
8. Junction box (not provided)
Figure 1
Rotation
Tilt
Center of rotation
1
2
3
4
5
6
7
8
Parts List
1. Lamp heads (2 or 3)
2. Canopy screws
3. Canopy
4. Lock washer
5. Nut
6. Junction box screws (not provided)
7. Spider plate
8. Junction box (not provided)
Figure 1
Rotation
Tilt
Center of rotation
Note: Lamp heads may already be attached to the canopy.
1. Determine the final position for the lamp heads.
2. Look for the mark on the threaded portion of the swivel to
find the center of rotation for the lamp head.
3. Insert the square surface from the swivel into the square
hole on the canopy ensuring that the center of rotation is as
close as possible to the final position. Secure the lamp head
in place with the lock washer and nut provided.
4. Adjust the heads into there final position.
5. Install the spider plate to the junction box using the junction
box screws.
6. Make the proper connections. The fixture is designed for 6,
12 or 24 VDC (see the lamp voltage indicated on the inside
surface of the canopy). Connect the lamp wires to the DC
supply wires.
7. Use the canopy screws to fix the canopy to the spider plate.
Adjust the lamp head:
Rotation: hold the lamp head and turn it to either side.
-Note: The lamp head can be rotated 150° to either side.
Tilting: hold the lamp head and tilt it up or down.
The lamp head uses a ratchet type mechanism that moves it in
10 degree increments (see fig. 1).
Remote heads – Installation instructions
Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com
Remote heads – Installation instructions
Installation instructions
Note: Lamp heads may already be attached to the canopy.
1. Determine the final position for the lamp heads.
2. Look for the mark on the threaded portion of the swivel to
find the center of rotation for the lamp head.
3. Insert the square surface from the swivel into the square
hole on the canopy ensuring that the center of rotation is as
close as possible to the final position. Secure the lamp head
in place with the lock washer and nut provided.
4. Adjust the heads into there final position.
5. Install the spider plate to the junction box using the junction
box screws.
6. Make the proper connections. The fixture is designed for 6,
12 or 24 VDC (see the lamp voltage indicated on the inside
surface of the canopy). Connect the lamp wires to the DC
supply wires.
7. Use the canopy screws to fix the canopy to the spider plate.
Adjust the lamp head:
Rotation: hold the lamp head and turn it to either side.
-Note: The lamp head can be rotated 150° to either side.
Tilting: hold the lamp head and tilt it up or down.
The lamp head uses a ratchet type mechanism that moves it in
10 degree increments (see fig. 1).
10/12 750.1694 Rev. A
1/1
Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com
10/12 750.1694 Rev. A
1/1
Loading...