Emerald Energize EM5, Energize EM6 Owner's Manual
MODELS: EM5 & EM6
Owner’s Manual
2012
Important Information Enclosed:
Please read before setting-up or using your spa
Rev 1.1.12
TABLE OF CONTENTS
Important Safety Instructions .......................................................................................................................... …….. 2
Location and Installation ................................................................................................................................ …….. 4
Spa Set Up ..................................................................................................................................................... …….. 5
Water Care, Consumer Notice ....................................................................................................................... …….. 7
Spa Care and Maintenance ...........................................................................................................................…….. 8
Winterizing ...................................................................................................................................................... …….. 9
Control Panel Instructions ……………………………………….…………………………………………………………… 10
Troubleshooting Topside Control Error Codes …………………………………………………………………………... 11
Troubleshooting ............................................................................................................................................. …….. 12
Spa Information............................................................................................................................................... …….. 13
Warranty..........................................................................................................................................................…….. 14
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
1.
READ AND FOLLOW ALL INSTRUCTIONS
2. DANGER - Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid
accidents, ensure that children cannot use this spa unless they are supervised at all times.
3. DANGER - Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should
the need arise to replace the suction fittings or the pump, be sure that the flow rates are compatible. Never operate the spa if the
suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original
fitting.
4. DANGER - Risk of Electric Shock. Install at least 5 feet (1.52 m) from all metal surfaces. As an alternative, a spa may be installed
within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum No. 8 AWG (8.4 mm2) solid copper
conductor to the wire connector on the terminal box that is provided for this purpose.
5. DANGER - Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone, radio, or television, within 5 feet
(1.52 m) of a spa.
6. WARNING – To reduce the risk of injury, the water in the spa should never exceed 104°F (40°C). Water temperatures between
100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult for a 10-to-15 minute time period. Lower water temperatures are recommend for extended use (exceeding 10-15 minutes) and for younger adults/children.
7. WARNING – To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
8. A wire connector is provided on this unit to connect a minimum No. 8 AWG (8.4mm2) solid copper conductor between this unit and
any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.52 m) of the unit.
9. Excessive water temperatures have a high potential for causing fetal damage during pregnancy. Pregnant women should limit spa
water temperatures to 100°F (38°C) and only use the spa under the direction of a licensed physician.
10. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the possibility of drowning.
11. Persons taking medication should consult a licensed physician before entering the spa.
12. Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory system problems,
or diabetes should consult a licensed physician before entering the spa.
13. CAUSES, SYMPTOMS AND EFFECTS OF HYPERTHERMIA - Hyperthermia occurs when the internal temperature of the body
reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of hyperthermia include an increase
in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include (1) failure
to perceive heat, (2) failure to recognize the need to exit spa, (3) unawareness of impending hazard, (4) fetal damage in pregnant
women, (5) physical inability to exit the spa, (6) unconsciousness resulting in the danger of drowning.
14. The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.
15. During winter months where the temperature is consistently below freezing, check your spa periodically to ensure that it is operating
correctly and that the power to the spa has not been interrupted as to protect the water lines from freezing.
16. Do not use your spa alone.
17. People with infectious diseases should not use the spa.
18. To avoid injury, use care when entering or exiting the spa.
19. Do not use the spa immediately following strenuous exercise.
20. Maintain proper water chemistry in accordance to manufacturers’ instruction.
2
ELECTRICAL SAFETY INSTRUCTIONS
1. Read & follow all safety instructions.
2. A green colored terminal or a terminal marked G, GR, Ground, Grounding, or the international symbol is located inside the supply
terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means
provided in the electric supply panel with a continuous copper equivalent in size to the circuit conductors supplying this
equipment.
3. The equipment must be provided with a ground fault circuit interrupter located in the disconnect switch, as installed by a licensed
electrician.
4. The electrical service panel should be equipped with a 20-amp switch.
5. The electrical supply for the spa must include a suitably rated switch or circuit breaker to open all ungrounded supply conductors,
to comply with section 422-30 of the National Electrical Code, ANSI/NFPA 70-2002. The disconnecting means must be readily
accessible to the spa occupant, but must not be within 5 feet (1.52 m) of the spa.
6. All field-installed metal components such as rails, ladders, drains or other similar hardware within 3 meters of the spa shall be
bonded to the equipment grounding bus with copper wire conductors not smaller than No. 6 AWG.
7. For units intended for use other than single family dwellings, a clearly labeled emergency switch shall be provided as part of the
installation. The switch shall be readily accessible to the occupants and shall be installed at least 5 feet (1.52 m) away, adjacent
to, and within sight of, the unit
8. WARNING: Improper electrical connections or conductor sizing may cause the equipment module to operate improperly, create
the potential for an electrical hazard, and may void the warranty.
9. CAUTION: Use only approved pressure-type wire splicing lugs or connectors suitable for the size and type of wiring used.
If your hot tub is equipped with audio components, the following instructions also apply:
1. CAUTION - Risk of Electric Shock. Do not leave component access panel open.
2. CAUTION - Risk of Electric Shock. Replace components only with identical components.
3. CAUTION - Do not operate the audio components while inside the spa.
4. WARNING - Prevent Electrocution. Do not connect any auxiliary components (for example cable, additional speakers,
headphones, additional audio/video components, etc.) to the system.
5. These units are not provided with an outdoor antennae; when provided, it should be installed in accordance with Article 810 of the
National Electrical Code, ANSI/NFPA 70.
6. Do not service this product yourself as opening or removing covers may expose you to dangerous voltage or other risk of injury.
Refer all servicing to qualified service personnel.
7. If the power supply connections or power supply cord(s) are damaged; if water is entering the audio equipment compartment
area; if the protective shields or barriers are showing signs of deterioration; or if there are signs of other potential damage to the
unit, turn off the unit at the disconnect switch and refer servicing to qualified service personnel.
8. This unit should be subjected to periodic routine maintenance (for example, once every 3 months) to make sure that the unit is
operating properly.
9. Replace damaged cord immediately.
10. Do not bury electrical cables or cords.
3
LOCATION AND INSTALLATION
Your spa has been conveniently designed for use in either an indoor or outdoor setting. While selecting an appropriate location for
your spa, there are important things to consider.
Indoor Considerations
1. Walls, ceiling, flooring, and/or hardwood must be able to withstand high humidity. Just like in your bathroom, an exhaust fan
would be a good idea.
2. Spa Chemicals in the air may corrode certain metals in your home.
3. A self-draining floor is a great way to ease any worries about spilled water.
4. Spas must be accessible at all times to permit servicing if needed. Cost associated with the removal of walls, pulling a spa out of
an enclosed area, etc. are not the responsibility of the manufacturer. All costs associated with these types of items will be the
sole responsibility of the homeowner.
5. Remember that you'll need extra space to store the cover when it is removed. When using our handy cover-lift device, you
should allow for an extra 16" of clearance behind the spa.
6. The spa must be placed on a solid, flat, and level surface that does not move or shake.
7. You should consult with a builder or engineer to determine if your floor will support the spa weight. Remember, you must allow
for the spa, water, and people in your total weight calculations.
8. Be sure your spa is secure from access by young children. We offer a locking spa cover, but we also suggest keeping the spa
room locked and off limits to children.
Outdoor Considerations
1. Place your spa on a solid, flat, and level surface. We recommend a 4" thick reinforced concrete pad as the best surface. Dirt,
sand, concrete pavers, paver stones, etc. are not acceptable surfaces for your spa and these surfaces will void all warranty
claims. See figure 1 below for more information.
2. Keep in mind natural elements such as wind, sun, falling leaves, etc. Also consider lighting, visibility from the house, and
accessibility.
3. We recommend that you locate your spa in a locked fenced-in area to prevent access to the spa by children.
4. It is a good idea to have a contractor review your proposed site to see that there are no support problems. There are often local
ordinances that need to be met for spa use.
RECOMMENDED SUPPORT
Figure 1
Service
At least 5 feet
Figure 2
4
GFCI
Indoor or Outdoor Considerations
1. When installing the spa, provide for adequate drainage to prevent water from entering the equipment module area.
2. When installing the spa, enable access to the equipment compartment. Refer to figure 3 below for information pertaining to your
exact spa model.
3. Never locate light switches or other electrical components within reach from inside your spa. The equipment module must remain
protected by the skirting of the spa.
Wherever you locate your spa, you will need to have access to water in order to fill it. Also, you will need to be able to drain your spa
periodically. Since your spa water will likely have chemicals in it, you won't want to drain your spa on the lawn or into a garden. Be
sure you can reach a garden hose from the spa to where you plan to drain the water. Never let water get on the equipment module
that is located in the door opening of your spa.
= Drain
EM5 EM6
= Equipment Access
SPA SET UP
Figure 3
General Procedures
This section covers the installation of your spa. All electrical steps must be performed by a licensed electrician. The spa must be
connected to a proper power supply and meet all National Electrical Code (N.E.C.) and local code requirements. The connection must
include the conductors necessary for operation and bonding, as required by N.E.C.
1. Remove the spa from its shipping container and retain all safety, operation, and warranty information.
2. Position the spa on a flat, level surface such as concrete, or a wood deck which provides adequate drainage.
3. Position the spa at least 5 feet from all metal surfaces unless each metal surface is permanently connected to a bonding wire, as
indicated in the next step (see figure 2 on page 4).
4. The spa may be installed within 5 feet of metal surfaces as follows:
•
Your electrician will drill the hole into the spa bottom tray to hook up your electrical wire.
•
Installation must be in accordance with Article 680-(40-44) of the National Electrical Code, ANSI/NFPA 70-2002.
•
Each metal surface must be permanently connected to a bonding wire which is attached to a pressure wire connector
provided for that purpose.
•
The pressure wire connector is located on the equipment system control enclosure.
•
The bonding wire must be at least No. 8 AWG (8.4 mm²) solid copper wire, in accordance with article 680-43E.
•
The bonding wire must be attached to the pressure wire connector and all metal equipment, metal enclosures of electrical
equipment, metal water pipe, or conduit within 5 feet of the spa.
5
Loading...