Page 1
Replacement Parts
List
EmberGlo Model ES5TS
Designed to Operate W ithout
Distilled Water
EmberGlo
A Division of Midco International Inc.
4140 West Victoria Street
Chicago, Illinois 60646
tel 773.604.8700
fax 773.604.4070
web www.emberglo.com
EmberGlo
Quality Designed for Proven Performance
Automatic Timer/Push Button Dual
Operation Steamer with Water Pan
PRINTED IN U.S.A.
299
8472-51
Items listed are replacement parts for the current Model ES5TS Tap Water Steamer and its
components.
Model ES5TS first construction August, 1985
■■
■■ Original construction featured a non-counter balanced 90° opening lid. Steamers built
after January 29, 1990 (date code 0590) feature a counter balanced adjustable 60° or
90° opening lid.
■■
■■ A limited number of early steamers were constructed with 15 minute timers. Refer to
page 3, Timers.
■■
■■ Original patterns for early Sand Cast Aluminum Generators replaced by Semi
Permanent Molds August 27, 1992 (date code 3592). Refer to page 3, Generators.
AVOID ERROR IN PARTS SELECTION. When ordering use complete Ember•Glo part number
and description; furnish steamer model number, date code, bill of material number, serial
number and component nameplate data where available.
Page 2
2
Page 3
3
PART NUMBER DESCRIPTION
1400-40 Shell Weldment
1401-10 Rear Bottom
1401-30 Bulb Clamp
1401-60
1
Generator (120 volt)
1401-90 Food Pan
1402-10 Water Pan Rivetment
1402-70 Water Inlet
1403-70 Power Cord (3 Prong, 120 volt)
1406-50 Water Pan Slide Weldment
1407-10 Water Pan Shell Weldment
1407-70 Leg Channel
1408-90 Water Pan Front
1409-00 Stiffener
1409-60 Water Tube Clip (2 required)
1409-70 Control Box Cover Assembly
1409-80 Timer Label
1410-30 Short Water Tube and Fittings
1411-00 Water Pan Baffle Set
1411-20 Water Nozzle with Spring
1411-50* Timer Dial and Button (30 min.)
1412-50 Shot Timer Assembly (120 volt)
1412-60 Water Nozzle Spring only
1415-30 Pump Hose (2 required)
1415-50 Hose Connector (2 required)
1415-80 Water Tube
1415-90 Pump Hose Spring (2 required)
1416-00 Dip Tube Assembly
1416-60 Pump Orifice
1416-80 Pump Bracket tie
1417-00 Pump Bracket
1417-20 Switch Panel
1417-40 Front Bottom Panel
1418-00 Pump Clamp (2 required)
1418-20 Shot Timer Gear Guard
1420-00 Hinge Spring Bar (2 required)
1420-40 Hinge Spring (2 required)
1420-80 Lid Assembly (Lid and Handle)
1421-00 Adjustable Lower Hinge
1421-50 Hinge Lid Stop Rivetment
1421-60 Adjustable Upper Hinge
1423-00 Oscillating Pump (120 volt)
1425-00 Signal Buzzer (120 volt)
1435-00 Lid Handle Replacement Kit
* Refer to Timers below
1. Refer to Generators below
PART NUMBER DESCRIPTION
5608-50 Food Grid
5616-90 Strain Relief (SR-6P-4)
5661-80 Aluminum Leg (4 required)
8406-51* Main Timer (120 volt, 30 min.) with Timer
Dial and Button
8408-66 Ready Light
8423-14 On-Off Rocker Switch
8423-21 Toggle Switch (Buzzer Switch)
8423-22 Push Button Switch
8425-08 Thermostat
8432-08
5
/16" OD x 3/16" ID O-Ring (2 required)
8445-01 Water Pan Knob
8450-25 Socket Tip (4 required)
8451-74 Strainer
8451-76 Locknut RP1827
8451-77
1
/2" Hose Clamp (2 required)
8451-89
9
/16" Dia. Plug Button
8452-10
29
/64" Hose Clamp (2 required)
8483-14
1
/8MPT x 1/4T ST Brass Comp. Fit
8483-15
1
/8Brass Street El
8483-36
1
/8Brass Elbow
8483-37
1
/8F x 1/4T Compression El
8484-76 Snap Bushing (B-500-375)
The Following Are Not Shown
1410-50 Insulation Kit (Sides, Back, Front & Bottom)
1411-70 Electrical Wire Kit (less power cord)
1419-00 Adjustable Hinge Retrofit Kit and Hardware
1446-00 Thermostat Disc to Bulb Kit
PART NUMBER HARDWARE (obtain locally)
H1
1
/4Compression Nut
H2
1
/4Compression Sleeve
H3 10-32 x 2 Round Head Machine Screw
H4 10-32 x
3
/8Truss Head Machine Screw
H5 6-32 x
1
/4Truss Head Machine Screw
H6 8 x
3
/8Truss Head Type "B"
H7 10-24 x
3
/8Round Head Machine Screw
H8 6 x 1/4Pan Head Type "AB"
H9 #10 Stainless Steel Lockwasher
H10
9
/16-18 Pal Lock Nut
H11
1
/4-20 x 2 Round Head Machine Screw
H12 8-32 x
5
/16Pan Head Machine Screw
GENERA TORS
Original patterns for Sand Cast Aluminum generators replaced by Semi Permanent Molds August 27, 1992 (Date Code 3592).
Generators from Semi Permanent Molds feature vertical ribs on each wall of Generator cavity. These ribs inhibit the food pan
from nesting against any wall. When replacing an early (without ribs) Generator, the two bolt holes in the REAR BOTTOM panel
must be filed to accommodate the new Generator. The distance between centers on the two
1
/4-20 mounting bosses has been
reduced
1
/4inch (was 121/2" now 121/4"). If this is not acceptable, order 1401-10 REAR BOTTOM panel when ordering a
replacement Generator.
Note: Replacing the REAR BOTTOM panel is labor intensive. We recommend filing the existing REAR BOTTOM panel.
TIMERS
A limited number of early steamers were constructed featuring 15 minute timers. Only the listed 30 minute timer and dial are
currently available as replacement items. When replacing a 15 minute timer, the steamer must be upgraded to the 30 minute
version. Order a 30 minute timer, timer dial and button.
Page 4
ADJUSTABLE HINGE FOR 2-POSITION LID OPENING
(60° OR 90° OPEN)
First construction January 29, 1990 (date code 0590). Steamers built before this date featured a 90° opening lid. Replacement
parts for the early construction are no longer available. When replacing any parts on the early design or if converting to 2position lid opening, order Part Number 1419-00 ADJUSTABLE HINGE RETROFIT KIT.
TO REMOVE LID OR CHANGE
OPENING
4
Remove lid stop rivetment by sliding it up and
away from steamer. Raise lid as far back as it
will go, remove springs. Remove lid. Inverting
lid stop rivetment changes lid opening from
60° to 90° or from 90° to 60°.
TO RESET LID
Remove lid stop rivetment and springs. Loosen
four 10-32 x 3/8Phillips truss head screws in
lower hinge. Place a coin under lid and on top
of generator rim at both rear corners. Hold lid
down along front edge. Tighten screws.
Reinstall springs and lid stop rivetment.
Loading...