EMAUX Operating Instructions & Parts Manual
Notes/Notas/Notes
88041101, 88040101
Ope ratin g Instr uctio ns & Part s Manua l
Please refer and save these instructions. Read carefully before attempting to assemble, install, operate or
maintain the product described. Protect yourself and others by observing all safety information. Failure to
comply with instructions could result in personal injury and/or property damage! Retain instructions for future
reference.
Description
The EMAUX Plastic Spa Light is durable, easily installed underwater light for
pool and spa. Especially designed for pool and spas, it provides
breathtaking color at the flip of a switch. it is a must for nighttime pool
safety and enjoyment. It can also enhance your pool and spa's beauty and
help create an inviting backyard environment after the sun goes down.
88041101, 88040101
E
N
G
L
I
S
H
EMAUX P50
Plastic Spa Light
Unpacking INSTALLATION
When unpacking the unit, inspect (For vinyl and fiberglass swimming
carefully for any damage that may pool only)
have occurred during transit. Check
A. Preparatory steps
for missing accessories or damaged
1) Ensure that the electrical system
parts. Transit damage claims should
and its wiring for the pool conform
be made to the shipping company.
to the requirements of your
Specifications
govenment or your local
(For Plastic Spa Light only) authorities. The installa-tion of the
Model: 88041101, 88040101 Underwater Light should only be
4) The mounting bracket must be
per-formed by a licensed
properly instal-led so that the
electrician.
top edge of the Underwater
Light lens is at least 45CM below
2) The junction box, or the low
the surface of the water in the
voltage transfor-mer for 12 volt
pool, see Figure 1.
Underwater Light model is to be
5) Consult the local Government
located at least 120CM from
Building Departm-ent to be
the edge of the pool, see Figure 1.
certain that the pool's electrical
3) The light fixture and all metal
system .meets all applicable
parts that are within 240CM of
requirements.
the pool must be properly
RISK OF ELECTRICAL SHOCK OR
6) The underwater light should be
protected with non-ductile
ELECTROCUTION
installed on a flat and rigid
materials and that the
This underwater light fixture must be
surface.
connections must be waterproof.
installed by a licensed or certified
electrician or a qualified serviceman
in accordance to the requirements
of your government standard or
local authorities. Improper installation
will create electric hazards which
could result in serious injury, death as
well as damage to the property.
Before servicing the light, disconnect
the power supply from the circuit
breaker. Failure to do so could result
in serious injury, death or damage to
the property.
DAN GER
Ф
Figure 1.
EMLI16022951
B) INSTALLATION
for more than 10 seconds,
1) Punch or drill a hole
fill the pool with water until
(Diameter = 62mm) in the
the underwater light is
desired location on the
completely submerged in
pool wall, see Figure 1. Be
water. To check for proper
sure the top of the hole be
operation, turn on main
at least 18 inches below
switch or circuit breaker as
the water level.
well as the switch that
2) Put a O-ring on the pool
operates the underwater
wall and then feed the
light itself.
cord throught the hole.
3) Use the nut provided to fix
the underwater light on the
A) Never operate this
pool wall, as shown in
Underwater Light for more
Fugure 2.
than 10 seconds unless it is
totally submerged in water.
Without total submersion,
the light assembly will get
extremely hot, which may
result in serious injury to
pool users, installers, or
damage to property.
B) Be sure power is off before
installing or removing lamp.
Allow lamp to cool before
relamping. This light fixture
uses a Halogen Quartz
4) Feed cord to junction box,
lamp. Do Not touch lamp
strip 6 inches of the outer
with bare hand, this may
cord jacket to expose the
severely reduce its life. Use
insulation wires and make
the plastic furnished with
the wire connection to the
the replacement lamp to
junction box.
eliminate finger prints from
5) Secure the junction box
getting on lamp.
cover in place.
6) Before operating the light
EMAUX Operating Instructions & Parts Manual
88041101, 88040101
EMAUX P50 Plastic Spa Light
WAR NING
Figure 2.
2
1
2
4
3
5
6
7
8
9
EMAUX Operating Instructions & Parts Manual
88041101, 88040101
Figure 3 – Repair Parts Illustration for Plastic Spa Light
Repair Parts list for Plastic Spa Light
3
Repair Parts list for Plastic Spa Light
Key N o.
Par t No.
Des cript ion
Qty
1*
012 21001
P50 L ight Co lour Le ns (Red +Gree n+Blu e)
1
1*
012 21001 C
UL- P50 Lig ht Colo ur Lens ( Clear )
1
2
010 41019
Ins ide Cov ers for P 50 Ligh ts
1
3
020 21010
O-R ing14
040 11001
Hal ogen la mp MR16 A C 12V/2 0W for UL -P50
1
4
040 11016
LED -P50 la mp 12V/ 1W (Aut omati c Colou r-Cha nging )
1
4
040 11015
LED -P50 la mp 12V/ 1W (Whi te Colo ur Only )
1
5
020 21000
O-r ing for E ncasi ng
2
6
890 41101
P50 L ights E ncasi ng Set
17010 21007
Nut
1
8
890 41102
Con necto r with Ga sket fo r Cable
1
9
040 13001
Lig hts Cab le 1.5M f or P50
1
Not es:1* 0 12210 01 is UL- P50 Lig ht Colo ur Len 1 se t with (R ed+Gr eee+B lue) or
1* 01 22100 1C is UL- P50 Lig ht Colo ur Len wi th (Cle ar)
Loading...