eMachines V700 Series User Manual

eMachines Projector

V700 Series

User's Guide

Copyright © 2010. Acer Incorporated.
All Rights Reserved.

eMachines Projector V700 Series User's Guide
Original Issue: 03/2010

Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.

Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.

eMachines Projector V700 Series

Model number: __________________________________

Serial number: ___________________________________

Date of purchase: ________________________________

Place of purchase: ________________________________

eMachines and the eMachines logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to their
respective companies.

TM

"HDMI

, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC."

iii

Information for your safety and
comfort

Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.

Turning the product off before cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Caution for plug as disconnecting device

Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:

• Install the power supply unit before connecting the power cord to the AC

power outlet.

• Unplug the power cord before removing the power supply unit from the

projector.

• If the system has multiple sources of power, disconnect power from the

system by unplugging all power cords from the power supplies.

Caution for Accessibility

Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to

disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.

Warnings!

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. If the product

falls, it could be seriously damaged.

• Slots and openings are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.

This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.

• Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.

iv

• To avoid damage of internal components and to prevent battery leakage,

do not place the product on a vibrating surface.

• Never use it under sporting, exercising, or any vibrating environment

which will probably cause unexpected short current or damage rotor
devices, lamp.

Using electrical power

• This product should be operated from the type of power indicated on the

marking label. If you are not sure of the type of power available, consult
your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this

product where people will walk on the cord.

• If an extension cord is used with this product, make sure that the total

ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.

• Do not overload a power outlet, strip or receptacle by plugging in too

many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.

• This product's AC adapter is equipped with a three-wire grounded plug.

The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.

Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.

Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.

• Use the product only with the supplied power supply cord set. If you need

to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.6 meters (15 feet) maximum length.

Product servicing

Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.

Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:

• the power cord or plug is damaged, cut or frayed

• liquid was spilled into the product

• the product was exposed to rain or water

• the product has been dropped or the case has been damaged

• the product exhibits a distinct change in performance, indicating a need

for service

• the product does not operate normally after following the operating

instructions

Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.

v

Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.

Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.

Additional safety information

• Do not look into the projector's lens when the lamp is on. The bright may

hurt your eyes.

• Turn on the projector first and then signal sources

• Do not place the product in following environments:

• Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.

• Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.

• Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.

• Locations near fire alarms.

• Locations with an ambient temperature above 40 ºC/104 ºF.

• Locations where the altitudes are higher than 10000 feet.

• Unplug immediately if there is something wrong with your projector. Do

not operate if smoke, strange noise or odor comes out of your projector. It

vi

might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.

• Do not keep using this product to break or drop it. In this case contact your

dealer for inspection.

• Do not face the projector lens to the sun. It can lead to fire.

• When switching the projector off, suggest to ensure the projector

completes its cooling cycle before disconnecting power.

• Do not turn off the main power abruptly or unplug the projector during

operation. It can lead to lamp breakage, fire, electric shock or other
trouble. The best way is to wait for the fan to turn off before turning main
power off.

• Do not touch air outlet grille and bottom plate which becomes hot.

• Clean the air filter frequently if have. The temperature inside may rise and

cause damage when the filter/ventilation slots clogged with dirt or dust.

• Do not look into the air outlet grille when projector is operating. It may

hurt your eyes.

• Always open the lens shutter or remove the lens cap when the projector is

on.

• Do not block the projector lens with any object when the projector is

under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.

• The lamp becomes extremely hot during operation. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.

• Do not operate lamps beyond the rated lamp life. It could cause it to break

on rare occasions.

• Never replace the lamp assembly or any electronic components unless the

projector is unplugged.

• The product will detect the life of the lamp itself. Please be sure to change

the lamp when is showing warning message.

• When changing the lamp, please allow unit to cool down, and follow all

changing instructions.

• Reset the "Lamp Hour Reset" function from the Onscreen display

"Management" menu after replacing the lamp module.

• Do not attempt to disassemble this projector. There are dangerous high

voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.

• Do not stand the projector on end vertically. It may cause the projector to

fall over, causing injury or damage.

• This product is capable of displaying inverted images for ceiling mount

installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.

vii

Caution for Listening

To protect your hearing, follow these instructions.

• Increase the volume gradually until you can hear clearly and comfortably.

• Do not increase the volume level after your ears have adjusted.

• Do not listen to music at high volumes for extended periods.

• Do not increase the volume to block out noisy surroundings.

• Decrease the volume if you can't hear people speaking near you.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm

Mercury advisory

For projectors or electronic products containing an LCD/CRT monitor or display:

“Lamp(s) contain Mercury,
Dispose Properly.”

Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org

viii

First things first

Usage Notes

Do:

• Turn off the product before cleaning.

• Use a soft cloth moistened with mild detergent to clean the display

housing.

• Disconnect the power plug from AC outlet if the product is not being used

for a long period of time.

Don't:

• Block the slots and openings on the unit provided for ventilation.

• Use abrasive cleaners, waxes or solvents to clean the unit.

• Use under the following conditions:

• In extremely hot, cold or humid environments.

• In areas susceptible to excessive dust and dirt.

• Near any appliance that generates a strong magnetic field.

• Place In direct sunlight.

Precautions

Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.

Warning:

• Do not look into the projector's lens when the lamp is on. The bright light may hurt

your eyes.

• To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

• Please do not open or disassemble the product as this may cause electric shock.

• When changing the lamp, please allow unit to cool down, and follow all changing

instructions.

• This product will detect the life of the lamp itself. Please be sure to change the lamp

when it shows warning messages.

• Reset the "Lamp Hour Reset" function from the Onscreen display "Management"

menu after replacing the lamp module.

• When switching the projector off, please ensure the projector completes its cooling

cycle before disconnecting power.

• Turn on the projector first and then the signal sources.

• Do not use lens cap when projector is in operation.

• When the lamp reaches the end of its life, it will burn out and may make a loud

popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".

Information for your safety and comfort iii

First thing first x

Usage Notes x

Precautions x

Introduction 1

Product Features 1

Package Overview 2

Projector Overview 3

Projector Outlook 3

Remote Control and Control Panel Layout 4

Getting Started 6

Connecting the Projector 6

Turning the Projector On/Off 7

Turning on the Projector 7

Turning off the Projector 8

Adjusting the Projected Image 9

Adjusting the Height of Projected Image 9

How to optimize image size and distance 10

How to get a preferred image size by adjusting
distance and zoom 12

User Controls 14

Installation menu 14

eMachines Empowering Technology 15

Onscreen Display (OSD) Menus 16

Color 17

Image 18

Setting 21

Contents

Management 23

Audio 23

Timer 24

Language 24

Appendices 25

Troubleshooting 25

LED & Alarm Definition Listing 29

Replacing the Lamp 30

Ceiling Mount Installation 31

Specifications 34

Compatibility modes 36

Regulations and safety notices 40

1

Introduction

Product Features

This product is a single-chip DLP® projector. Outstanding features include:

• DLP

• Native 1280 x 720 720p resolution

• eMachines ColorBoost technology delivers nature's true colors for vivid,

• High brightness and contrast ratio

• Versatile display modes (Bright, Standard, Movie, Dark Cinema, Game,

• NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported

®

technology

4:3 / 16:9 / L.Box aspect ratio supported

life-like images

Sports, User) for optimum performance in any situation

English

• Lower power consumption and economy (ECO) mode extends lamp life

• eMachines EcoProjeciton Technology delivers Intelligent power

management approach and physical efficiency improvement.

• Empowering Key reveals eMachines Empowering Technology utilities

(eMachines eView, eTimer, ePower Management) for easy adjustment of
settings

• Advanced digital keystone correction optimizes presentations

• Multi-language onscreen display (OSD) menus

• Manual focus projection lens zooms up to 1.1X

• 2X digital zoom and pan move function

• Microsoft

®

Windows® 2000, XP, Vista®, Macintosh® OS compliant

English

2

Package Overview

This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.

Projector with lens cap Power cord VGA cable

XXXXXX

3V

eMachines Projector

Security Card

Composite video cable Battery Security card

V700

Quick Start Guide

www.emachines.com

V700

P/N: MU.JBD00.001

This CD contains:

• User Guide

• Acrobat Reader

C

.

o

d

p

e

y

v

r

r

i

g

e

s

h

e

t

©

r

2

s

t

0

h

0

g

9

i

r

.

l

A

l

User’s guide Remote control Quick start guide

Carrying case

3

English

Projector Overview

Projector Outlook

Front / upper side

Rear side

# Description # Description

1 Ventilation (inlet) 6 Lens cap
2 Ventilation (outlet) 7 Power button
3 Remote control receivers 8 Remote control
4 Focus ring 9 Zoom lever
5 Zoom lens 10 Horn

# Description # Description

1

Power socket

6

YPbPr input connector

2

Kensington

TM

lock port

7 S-Video input connector

3

RS232 connector 8 Composite video input connector

4 PC analog signal/HDTV/component video

input connector (VGA IN)

9 Audio input connector

5 HDMI connector

8

4

3

6

3

5

7

9

2

1

1

10

RS232

34 5 6 89

1

2

7

4

Remote Control and Control Panel Layout

English

1

2

8

3

9

8

4

5
6

7

2

10
11

12

13

# Icon Function Description

1 Remote control

receiver

2 POWER Refer to the "Turning the Projector On/Off" section.

3 MENU

Receives signals from remote control.

• Press "MENU" to launch the Onscreen display (OSD)

menu, back to the previous step for the OSD menu
operation or exit the OSD menu.

• Confirm your selection of items.

4 KeyPad 0~9 Press "0~9" to input a password in the "Security".

5 ASPECT RATIO To choose the desired aspect ratio (Auto/4:3/16:9/L.Box).

6 RESYNC Automatically synchronizes the projector to the input source.

7

8 KEYSTONE Adjusts the image to compensate for distortion caused by

9 Four directional

10 ZOOM Zooms the projector display in or out.

11 SOURCE Changes the active source.

12 HIDE Momentarily turns off the video. Press "HIDE" to hide the

FREEZE To pause the screen image.

tilting the projector (± 40 degrees).

Use up, down, left, right buttons to select items or make

select keys

adjustments to your selection.

image, press again to display the image.

5

English

Note:

Remote Control Placement

Please refer to the illustration to attach the remote control to the projector.

13 Empowering

key

Unique eMachines functions: eView, eTimer, ePower
Management.

# Icon Function Description

VZ.JBD00.001

English

6

Getting Started

Connecting the Projector

VGA

DVD player

D-Sub

RS232

2

RS232

1

S-Video Output

HDMI

3

D-Sub

Video Output

4

HDMI

5

RBG

Y

W

R

DVD player,
Set-top Box,
HDTV receiver

RBG

Y

9

8

6

7

# Description # Description

Power cord 6 Audio cable jack/jack

1

2 RS232 cable 7 Audio cable Jack/RCA

3 VGA cable 8 Composite video cable

4 HDMI cable 9 S-Video cable

5 3 RCA component cable

Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.

7

Turning the Projector On/Off

Turning on the Projector

1 Remove the lens cap.(Illustration #1)

2 Ensure that the power cord and signal cable are securely connected. The

Power indicator LED will flash red.

3 Turn on the projector by pressing "Power" button on the control panel,

and the Power indicator LED will turn blue. (Illustration #2)

4 Turn on your source (computer, notebook, video player ,etc.). The

projector will detect your source automatically.

• If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.

• If the screen displays "No Signal", please make sure the signal cables
are securely connected.

• If you connect to multiple sources at the same time, use the "Source"
button on the remote control to switch between inputs.

English

1

Lens cap

2

Power button

English

8

Turning off the Projector

1 To turn off the projector, press the "Power" button twice. The message

below will display onscreen for 5 seconds.

"Please press power button again to complete the shutdown process."

2 Immediately after powering off, the Power indicator LED will flash RED

rapidly and the fan(s) will continue to operate for about 120 seconds. This
is to ensure that the system cools correctly.

3 Once the system has finished cooling, the Power indicator LED will turn

solid RED which means projector enter standby mode.

4 It is now safe to unplug the power cord.

Warning: Do not turn on the projector immediately after
powering off.

Note: If you wish to turn the projector back on, you must wait for
60 seconds at least to press the "Power" button to restart the
projector.

Warning indicators:

• If the projector automatically shuts down and the Power indicator
quick flashing RED and steady BLUE by returns, please contact your
local reseller or service center.

• If the projector automatically shuts down and the Power indicator
quick flashing RED and steady BLUE by returns, this indicates that the
projector has overheated. The message below will display onscreen if
this is about to happen:

"Projector Overheated. Lamp will automatically turn off soon."

• If the Power indicator quick flashing RED and steady BLUE by returns
and the message below is displayed onscreen, please contact your
local dealer or service center:

"Fan fail. Lamp will automatically turn off soon."

9

Adjusting the Projected Image

Adjusting the Height of Projected Image

The projector is equipped with elevator feet for adjusting the height of image.

To raise/lower the image:

1 Use Tilt adjusting wheel (Illustration #1) to fine-tune the display angle.

English

1

Tilt adjusting wheel

English

Min screen size
80"

10

How to optimize image size and distance

Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 3 m from the screen, good image quality is possible for image sizes
between 80" and 87".

Note: Remind as below figure, the space of 122 cm height is
required when located at 3m distance.

Max screen size

Min screen size

87"

B

80"

Height:
112cm

A

3m
Desired Distance

Figure: Fixed distance with different zoom and screen size.

Height: 122cm
Form base to
top of image

C

11

English

Screen size

Desired

Distance

(m)

<A>

10.3 274 606 x 341 383 300 665 x 374 420

Zoom Ratio: 1.1x

Diagonal

(inch)

<B>

1 27 59 x 33 37 29 65 x 36 41

1.5 40 88 x 50 56 44 97 x 54 61

2 53 118 x 66 74 58 129 x 73 82

2.5 66 147 x 83 93 73 161 x 91 102

3 80 176 x 99 112 87 194 x 109 122

3.5 93 206 x 116 130 102 226 x 127 143

4 106 235 x 132 149 117 258 x 145 163

4.5 120 265 x 149 167 131 290 x 163 184

5 133 294 x 165 186 146 323 x 181 204

6 159 353 x 199 223 175 387 x 218 245

7 186 412 x 232 260 204 452 x 254 286

8 213 471 x 265 298 233 516 x 290 326

9 239 529 x 298 335 262 581 x 327 367

10 266 588 x 331 372 291 645 x 363 408

(Min zoom) (Max zoom)

W (cm) x

H (cm)

Top

From base to

top of image

(cm) <C>

Screen size

Diagonal

(inch)

<B>

W (cm) x

H (cm)

From base to top

of image (cm)

Top

<C>

English

12

How to get a preferred image size by adjusting
distance and zoom

A

50"

Desired
image size

Height

Form base to
top of image

D

1.7 m

B

1.9 m

C

The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. Example: to obtain an image size of 50" set the
projector at a distance 1.7 m and 1.9 m from the screen and adjust the zoom
level accordingly.

Desired Distance

Desired Image Size Distance (m) Top (cm)

13

English

Diagonal (inch)

<A>

30 66 x 37 1.0 1.1 42

40 89 x 50 1.4 1.5 56

50 111 x 62 1.7 1.9 70

60 133 x 75 2.1 2.3 84

70 155 x 87 2.4 2.6 98

80 177 x 100 2.7 3.0 112

90 199 x 112 3.1 3.4 126

100 221 x 125 3.4 3.8 140

120 266 x 149 4.1 4.5 168

150 332 x 187 5.1 5.6 210

180 398 x 224 6.2 6.8 252

200 443 x 249 6.9 7.5 280

250 553 x 311 8.6 9.4 350

300 664 x 374 10.3 *** 420

Zoom Ratio: 1.1x

W (cm) x H (cm)

Max zoom

<B>

Min zoom

<C>

From base to top of

image

<D>

English

14

User Controls

Installation menu

The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.

The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .

1 Turn on the projector by pressing "Power" button on the control pad.

2 Press the "MENU" button on the control pad to launch the OSD for

projector installation and maintenance.

3 The background pattern acts as a guide to adjusting the calibration and

alignment settings, such as screen size and distance, focus and more .

4 The Installation menu includes the following options:

•Projection method

•Projection location

•Menu location

•Keystone settings

•Language settings

•Reset to factory default function

Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.

5 Push the menu button anytime to exit the menu and return to the

eMachines welcome screen.

15

English

eMachines Empowering Technology

Empowering Key

eMachines Empowering Key provide
three eMachines unique functions, they
are "eMachines eView Management",
"eMachines eTimer Management" and
"eMachines ePower Management"
respectively. Press " " key for more

than one second to launch the
Onscreen display main menu to modify
its function.

eMachines eView
Management

Press " " to launch "eMachines
eView Management" submenu.

"eMachines eView Management" is for
display mode selection. Please refer to
Onscreen Display Menus section for
more detail.

eMachines eTimer
Management

Press " " to launch "eMachines
eTimer Management" submenu.

"eMachines eTimer Management"
provides the reminding function for
presentation time control. Please refer
to Onscreen Display Menus section for
more detail.

eMachines ePower
Management

Press " " to launch "eMachines
ePower Management".

"eMachines ePower Management"
provides user one shortcut to save lamp
and projector life. Please refer to
Onscreen Display section for more
detail.

English

16

Onscreen Display (OSD) Menus

The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.

Using the OSD menus

• To open the OSD menu, press "MENU" on the remote control.

• When the OSD is displayed, use the keys to select any item in the

main menu. After selecting the desired main menu item, press to enter
submenu for feature setting.

• Use the keys to select the desired item and adjust the settings by

using the keys.

• Select the next item to be adjusted in the submenu and adjust as described

above.

• Press "MENU" on the remote control, the screen will return to the main

menu.

• To exit OSD, press "MENU" on the remote control again. The OSD menu

will close and the projector will automatically save the new settings.

Main menu

Setting

Sub menu

17

Color

Display Mode

Wall color

Brightness

English

There are many factory presets optimized for various types of
images.

• Bright: For brightness optimization.

• Standard: For common environment.

• Movie: For brighter and general movie/video/photo playing.

• Dark Cinema: For dark movie content.

• Game: For game content.

• Sports: For sport picture.

• User: Memorize user’s settings.

Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.

Adjust the brightness of the image.

Contrast

Color
Temperature

Degamma

Color R
Color G
Color B

• Press to darken image.

• Press to lighten the image.

"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.

• Press to decrease the contrast.

• Press to increase the contrast.

Adjust the color temperature. At higher color temperatures, the
screen looks colder; at lower color temperatures, the screen looks
warmer.

Effects the representation of dark scenery. With greater gamma
value, dark scenery will look brighter.

Adjusts the red color.

Adjusts the green color.

Adjusts the blue color.

18

English

Saturation

Tint

Image

Adjusts a video image from black and white to fully saturated
color.

• Press to decrease the amount of color in the image.

• Press to increase the amount of color in the image.

Adjusts the color balance of red and green.

• Press to increase the amount of green in the image.

• Press to increase the amount of red in the image.

Note: "Saturation" and "Tint" functions are not supported under computer
mode or DVI mode.

Projection mode

Projection Location

• Front: The factory default setting.

• Rear: Reverses the image so you can project from behind a

translucent screen.

• Auto: Automatically adjusts projection location of image.

• Desktop

• Ceiling: Turns the image upside down for ceiling-mounted

projection.

19

English

Aspect Ratio

Use this function to choose your desired aspect ratio.

• Auto: Keep the image with original width-higth ratio and maxi

mize the image to fit native horizontal or vertical pixels.

• 4:3: The image will be scaled to fit the screen and displayed using

a 4:3 ratio.

• 16:9: The image will be scaled to fit the width of the screen and

the height adjusted to display the image using a 16:9 ratio.

Auto Keystone Automatically adjusts vertical image.

Manual Keystone Adjust image distortion caused by tilting projection. (±40 degrees)

<Note> The Manual Keystone funcion is unavailable under Auto
Keystone setting to "On".

H. Position
(Horizontal
position)

V. Position
(Vertical position)

• Press to move the image left.

• Press to to move the image right.

• Press to move the image down.

• Press to move the image up.

Frequency "Frequency" changes the projector's refresh rate to match the

frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.

Tracking Synchronizes the signal timing of the projector with the graphics card.

If you experience an unstable or flickering image, use this function to
correct it.

Sharpeness Adjusts the sharpness of the image.

• Press to decrease the sharpness.

• Press to increase the sharpness.

3D Choose "On" to enable 3D function supported by NVIDIA or TI DLP 3D

technology.

• On: Choose this item while using DLP 3D glasses, quad buffer

(NVIDIA/ATI...) graphic card and HQFS format file or DVD with
corresponding SW player.

• Off: Turn off 3D mode.

3D Sync L/R If you see a discrete or overlapping image while wearing DLP 3D

glasses, you may need to execute "Invert" to get best match of left/
right image sequence to get the correct image (for DLP 3D).

Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under DVI or Video mode.
Note: "Sharpness" functions is not supported under DVI and Computer
mode.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,

English

20

- NVIDIA Stereoscopic 3D Video Player:
http://www.nvidia.com/object/3D_Drivers_Downloads.html

- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx

- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html

Note: "3D Sync L/R" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.

21

Setting

Menu Location Choose the menu location on the display screen.

Source Lock When source lock is turned "off", the projector will search for

other signals if the current input signal is lost. When source lock is
turned "on", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.

Closed Caption Selects a preferred closed captioning mode from CC1, CC2, CC3,

CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> This function is not available when the aspect ratio is
"16:9" or 16:9 format detected under "Auto mode"..

Security Security

This projector provides a useful security function for the
administrator to manage usage of the projector .

Press to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first

before changing the security settings.

• Select "On" to enable the security function. The user has to

enter a password to operate the projector. Please refer to the
"User Password" section for details.

• If "Off" is selected, then the user can turn on the projector

without password.

Timeout(Min.)
Once "Security" is activated to "On", the administrator can set

timeout function.

English

• Press or to select the timeout interval.

• The range is from 10 minute to 990 minutes.

• When the time is up, the projector will prompt the user to

enter the password again.

• The factory default setting of "Timeout(Min.)" is "Off".

• Once the security function is enabled, the projector will

request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.

22

User password

• Press to setup or change the "User Password".

English

Reset

• Press number keys to set your password on the remote control

and press "MENU" to confirm.

• Press to delete character.

• Enter the password when you see "Confirm Password"

displayed.

• The password should be between 4 and 8 characters long.

• If you select "Request password only after plugging power

cord", the projector will prompt the user to enter the
password every time the power cord is plugged.

• If you select "Always request password while projector turns

on", the user has to enter the password every time when the
projector is turned on.

Administrator Password

The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.

• Press to change the "Administrator Password".

• The factory default of "Administrator Password" is "1234".

If you forgot your administrator password, do the following to
retrieve the administrator password:

• An unique 6-digit "Universal Password" which is printed on

the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.

• If losing this security card and number, please contact with an

eMachines service center.

• Press the button and choose "Yes" to return the

parameters on all menus to the factory default settings.

23

Management

ECO Mode

High Altitutde

Auto Shutdown The projector will automatically shutdown when there is no signal

Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).

Lamp Reminding Activate this function to display a reminder to change the lamp 30

Lamp Hour Reset

Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.

Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.

input after the allocated time. (in minutes)

hours before its expected end-of-life.

Press the button and choose "Yes" to turn the lamp hour
counter to 0 hours.

English

Audio

Volume

Mute

Power On/Off Volume

Alarm Volume

• Press to decrease the volume.

• Press to increase the volume.

• Choose "On" to mute the volume.

• Choose "Off" to restore the volume.

• Select this function to adjust the notification volume when

turning the projector on/off.

• Select this function to adjust the volume of any warning

votifications.

English

24

Timer

Timer Location

Timer Start

Timer Period

Timer Volume

Timer Display

Language

• Choose the location of the timer on the screen.

• Press to start or stop the timer.

• Press or to adjust the timer period.

• Select this function to adjust the nitification volume when

the timer function is enabled and time is up.

• Press or to which timer mode to display on the

screen.

Language

Choose the multilingual OSD menu. Use the or key

to select your preferred menu language.

• Press to confirm the selection.

25

Appendices

Troubleshooting

If you experience a problem with your eMachines projector, refer to the
following troubleshooting guide. If the problem persists, please contact your
local reseller or service center.

Image Problems and Solutions

# Problem Solution

1 No image appears

onscreen

• Connected as described in the "Getting Started"

section.

• Ensure none of the connector pins are bent or

broken.

• Check if the projector lamp has been securely

installed. Please refer to the "Replacing the Lamp"
section.

• Make sure you have removed the lens cap and the

projector is switched on.

English

2 Partial, scrolling

or incorrectly
displayed
image(For PC
(Windows 95/98/
2000/XP))

•

Press "

RESYNC

" on the remote control.

• For an incorrectly displayed image:

• Open "My Computer," open the "Control

Panel," and then double-click the "Display"
icon.

• Select the "Settings" tab.

• Verify that your display resolution setting is

lower than or equal to UXGA (1600 x 1200).

• Click the "Advanced Properties" button.

If the problem still appears, change the monitor display
you are using and follow the steps below:

• Verify that the resolution setting is lower than

or equal to UXGA (1600 x 1200).

• Click the "Change" button under the

"Monitor" tab.

• Click "Show all devices". Next, select "Standard

monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.

• Verify that the resolution setting of the

monitor display is lower than or equal to UXGA
(1600 x 1200).

26

English

3 Partial, scrolling

or incorrectly
displayed image
(For notebooks)

4 The screen of the

notebook
computer is not
displaying your
presentation

5 Image is unstable

or flickering

• Press "RESYNC" on the remote control.

• For an incorrectly displayed image:

• Follow the steps for item 2 (above) to adjust

the resolution of your computer.

• Press the toggle output settings. Example:

[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]

• If you experience difficulty changing resolutions or

your monitor freezes, restart all equipment
including the projector.

• If you are using a Microsoft

notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.

• If you are using an Apple

notebook: In System Preferences, open Display and
select Video Mirroring "On".

®

Windows® based

®

Mac® OS based

• Adjust the "Tracking" to correct it. Refer to the

"Image" section for more information.

• Change the display color depth settings on your

computer.

6 Image has vertical

flickering bar

7 Image is out of

focus

8 Image is stretched

when displaying a
"widescreen"
DVD title

• Use "Frequency" to make an adjustment. Refer to

the "Image" section for more information.

• Check and reconfigure the display mode of your

graphics card to make it compatible with the
projector.

• Make sure the lens cap is removed.

• Adjusts the focus ring on the projector lens.

• Make sure the projection screen is within the

required distance of 3.3 to 33.8 feet (1.0 to 10.3
meters) from the projector. Refer to the "How to
Get a Preferred Image Size by Adjusting Distance
and Zoom" section for more information.

When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:

• If you play a 4:3 format DVD title, please change the

format to 4:3 in the projector OSD.

• If the image is still stretched, you will also need to

adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.

27

9 Image is too small

or too large

• Adjust the zoom lever on the front of the projector.

• Move the projector closer to or further from the

screen.

• Press "MENU" on the remote control. Go to "Image

--> Aspect Ratio" and try different settings or
press"Aspect Ratio" on the remote control to adjust
directly.

10 Image has slanted

sides

• If possible, reposition the projector so that it is

centered on the screen.

• Press the "Keystone / " button on the remote

control until the sides are vertical.

• Press "MENU" on the remote control. Go to "Image -

-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.

11 Image is reversed

• Select "Image --> Projection" on the OSD and adjust

the projection direction.

Problems with the Projector

English

# Condition Solution

1 The projector stops responding

to all controls

2 Lamp burns out or makes a

popping sound

If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.

When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.

28

OSD Messages

English

# Condition Message Reminder

1 Message Fan Fail - the system fan is not working.

Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.

Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.

29

LED & Alarm Definition Listing

LED Messages

Power LED

Message

Red Blue

Input Power Plug Flash ON to OFF 100ms --

Standby V --

Power button ON -- V

Lamp retry -- Quick Flashing

Power off (Cooling state) Quick Flashing --

Power button OFF:
Cooling completed;
Standby Mode

Error (Thermal Failure) Quick Flashing RED and Steady BLUE by returns

V--

English

Error (Fan lock) Quick Flashing RED and Steady BLUE by returns

Error (Lamp breakdown) Quick Flashing BLUE and Steady RED by returns

Error (Color Wheel fail) Quick Flashing BLUE and Steady RED by returns

English

30

Replacing the Lamp

Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.

The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.

Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.

1

3

2

4

To Change the Lamp
1 Turn off the projector by pressing the Power button.
2 Allow the projector at least 30 mins to cool down.
3 Disconnect the power cord.
4 Use a screwdriver to remove the screw from the cover. (Illustration #1)
5 Push up and remove the cover.
6 Remove the two screws that secure the lamp module (Illustration #2) and

pull up the lamp bar.(Illustration #3)

7 Pull out the lamp module by force. (Illustration #4)

To replace the lamp module, reverse the previous step.

Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.

31

Ceiling Mount Installation

If you wish to install the projector using a ceiling mount, please refer to the
steps below:

1 Drill four holes into a solid, structurally sound part of the ceiling, and

secure the mount base.

13

mm

20

mm

49.9

mm

mm

8.4

130 mm

English

Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.

2 Secure the ceiling rod using the appropriate type of four-cylinder screws.

Ceiling Mount Base

- Attach to ceiling

Short Rod

Long Rod

Extension Rod

Long Cylinder Cap

50 mm length / 8 mm diameter -

Screw Type A

Allen Key

- For tightening/looseni

Tightening Screw

Medium Rod

English

32

3 Use the appropriate number of screws for the projector size to attach the

projector to the ceiling mount bracket.

Screw Type B

Smaller Washer

Large Washer

Projector Bracket

Supports projector and allows -

for adjustments

Spacer

- For heat dissipation

Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.

4 Attach the ceiling bracket to the ceiling rod.

Screw Type A

50 mm length -

08 mm diameter

Large cylinder cap

Allen Key

- For tightening/loosening

Tightening Screw

33

5 Adjust the angle and positioning as necessary.

3

English

Tightening Screw

Allen Key

Allen Key

Tightening Screw

Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in

the screw pack.

Models Screw Type B Washer Type

Diameter (mm) Length (mm) Large Small

V700 3 25 V V

SCREW SPEC. M3 x 25 mm

82.30 mm

95.00 mm

15.00 mm

English

34

Specifications

The specifications listed below are subject to change without notice. For final
specs, please refer to eMachines's published marketing specifications.

Projection system

Resolution V700: Native: 720P (1280 x 720) , Maximum: UXGA

Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and

Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/

Aspect ratio Auto, 4:3, 16:9, L.Box

Displayable colors 1.07 Billion colors

Projection lens F/ 2.5 - 2.67, f = 21.86 mm - 24.00 mm, 1.1X manual

Projection screen size (diagonal) 27" (0.69m) - 300" (7.62 m)

Projection distance 3.3' (1.0 m) - 33.8' (10.3 m)

Throw ratio 58"@2m (1.55 - 1.70:1)

Horizontal scan rate 30k - 100 kHz

Vertical refresh scan rate 50-85 Hz, 120Hz (for 3D mode only)

Lamp type 200W user-replaceable lamp

Keystone correction

Audio Internal speaker with 2 W output

Weight 2.26 Kg (4.9 lbs.)

Dimensions (W x D x H) 268 mm x 192 mm x 80 mm (10.6" x 7.6" x 3.1")

Digital Zoom 2X

Power supply AC input 100 - 240 V auto-switching power supply

Power consumption

Operating temperature 5ºC to 35ºC / 41ºF to 95ºF

I/O connectors

®

DLP

(1600 x 1200), WSXGA+ (1680x1050),
1080p(1920x1080)

VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +

K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)

zoom lens

± 40 degrees

248W ± 10% for normal mode
201W ± 10% for ECO mode

• Power socket x1

• VGA input x1

• RS232 x1

• Composite video x1

• S-Video x1

• 3 RCA Component video x1

• HDMI x1

• 3.5 mm audio jack input x1

35

Standard package contents

* Design and specifications are subject to change without notice.

• AC power cord x1

• VGA cable x1

• Composite video cable x1

• Remote control x1

• Battery x1 (for remote control)

• User's guide (CD-ROM) x1

• Quick start guide x1

• Security card x1

• Carrying case x1

• HDMI cable x1

English

36

Compatibility modes

English

A. VGA Analog

1 VGA Analog - PC Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

VGA 640x480 60 31.47

640x480 72 37.86
640x480 75 37.50
640x480 85 43.27
640x480 119.51 61.60

SVGA 800x600 56 35.20

800x600 60 37.88
800x600 72 48.08
800x600 75 46.88
800x600 85 53.67
800x600 119.85 77.20

XGA 1024x768 60 48.36

1024x768 70 56.48
1024x768 75 60.02
1024x768 85 68.67
1024x768 119.804 98.80

SXGA 1152x864 70 63.80

1152x864 75 67.50

1152x864 85 77.10
1280x1024 60 63.98
1280x1024 72 77.90
1280x1024 75 79.98
1280x1024 85 91.15

QuadVGA 1280x960 60 60.00

1280x960 75 75.00

SXGA+ 1400x1050 60 65.32

UXGA 1600x1200 60 75.00
PowerBook G4 640x480 60 31.50
PowerBook G4 640x480 66.6(67) 35.00
PowerBook G4 800x600 60 37.88
PowerBook G4 1024x768 60 48.36
PowerBook G4 1152x870 75 68.68
PowerBook G4 1280x960 75 75.20

i Mac DV(G3) 1024x768 75 60.30

37

2 VGA Analog - Extended Wide timing

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.78

1280x768 75 60.29
1280x768 85 68.63
1280x720 60 44.80
1280x720 119.858 92.89
1280x800 60 49.60

1366x768 60 47.71
WXGA+ 1440x900 60 55.90
WSXGA 1680x1050 60 65.30

1920x1080-RB 60 66.60

1920x1080-EIA 60 66.60

1024x600 60 37.30

3 VGA Analog -Component Signal

480i 720x480 59.94(29.97) 27.00

480p 720x480 59.94 31.47

576i 720x576 50(25) 27.00
576p 720x576 50 31.25
720p 1280x720 60 45.00
720p 1280x720 50 37.50

1080i 1920x1080 60(30) 33.75

1080i 1920x1080 50(25) 33.75
1080p 1920x1080 60 67.50
1080p 1920x1080 50 56.26

English

B. HDMI Digital

(1) HDMI - PC Signal(same as DVI)

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

VGA 640x480 60 31.47

SVGA 800x600 56 35.20

XGA 1024x768 60 48.36

640x480 72 37.86
640x480 75 37.50
640x480 85 43.27
640x480 119.51 61.61

800x600 60 37.88
800x600 72 48.08
800x600 75 46.88
800x600 85 53.67
800x600 119.85 77.20

English

38

1024x768 70 56.48
1024x768 75 60.02
1024x768 119.804 98.80

SXGA 1152x864 70 67.50

1152x864 85 77.10
1280x1024 60 64.00
1280x1024 72 77.90
1280x1024 75 79.98
1280x1024 85 91.15

QuadVGA 1280x960 75 75.00
PowerBook G4 640x480 60 31.50
PowerBook G4 640x480 66.6(67) 35.00
PowerBook G4 800x600 60 37.88
PowerBook G4 1024x768 60 48.36
PowerBook G4 1152x870 75 68.68
PowerBook G4 1280x960 75 75.20

i Mac DV(G3) 1024x768 75 60.30

(2) HDMI - Extended Wide timing(same as DVI)

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.78

1280x768 75 60.29
1280x768 85 68.63
1280x720 60 44.80
1280x720 119.858 92.89
1280x800 60 49.60

1366x768 60 47.71
WXGA+ 1440x900 60 55.90
WSXGA 1680x1050 60 65.30

1920x1080-RB 60 66.60

1920x1080-EIA 60 66.60

1024x600 60 37.30

(3) HDMI - Video Signal

480i 720x480 59.94(29.97) 27.00

480p 720x480 59.94 31.47

576i 720x576 50(25) 27.00
576p 720x576 50 31.25
720p 1280x720 60 45.00
720p 1280x720 50 37.50

1080i 1920x1080 60(30) 33.75

39

1080i 1920x1080 50(25) 33.75
1080p 1920x1080 60 67.50
1080p 1920x1080 50 56.26

Graphic source moni-

tor range limits

English

Horizontal scan rate: 30-100kHz

Vertical scan rate: 50-85 Hz, 120Hz (for 3D mode only)

Max. pixel rate: 170MHz

40

Regulations and safety notices

English

FCC notice

This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.

Caution

Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

41

Remarque à l'intention des utilisateurs canadiens

Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.

Declaration of Conformity for EU countries

Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Compliant with Russian regulatory certification

Radio device regulatory notice

Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.

English

English

General

This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).

Canada — Low-power license-exempt radio
communication devices (RSS-210)

a Common information

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference
that may cause undesired operation of the device.

b Operation in 2.4 GHz band

To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.

List of applicable countries

This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm

for the latest country list.

8F, 88 , Sec. 1, Hsin Tai Wu Rd., Hsichih

Acer Incorporated

Taipei Hsien 221 , Taiwan

Declaration of Conformity

We,

Acer Incorporated

8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, e-mail:[e-mail]

And,

Acer Europe SA

Via Cantonale, Centro Galleria 2 6928 Manno Switzerland

Hereby declare that:

Product: Projector
Trade Name: eMachines
Model Number: H7P0901
Machine Type: V700

Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that
production units of the same product will continue comply with the requirements.

EMC Directive 2004/108/EC as attested by conformity with the following
harmonized standards:

-. EN55022, AS/NZS CISPR22, Class B

-. EN55024

-. EN61000-3-2 Class A

-. EN61000-3-3

Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:

-. EN60950-1

RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous
Substances in Electrical and Electronic Equipment

-. The maximum concentration values of the restricted substances by weight in homogenous
material are:

Lead 0.1% Polybrominated Biphenyls (PBB’s) 0.1%
Mercury 0.1% Polybrominated Diphenyl Ethers (PBDE’s) 0.1%
Hexavalent Chromium 0.1% Cadmium 0.01%

!

Directive 2009/125/EC with regard to establishing a framework for the setting
of ecodesign requirements for energy-related product.

8F, 88 , Sec. 1, Hsin Tai Wu Rd., Hsichih

Acer Incorporated

Taipei Hsien 221 , Taiwan

The standards listed below are applied to the product if built with WLAN
module or wireless keyboard and mouse.

R&TTE Directive 1999/5/EC as attested by conformity with the following
harmonized standard:

z Article 3.1(a) Health and Safety

-. EN60950-1

-. EN62311

z Article 3.1(b) EMC

-. EN301 489-1

-. EN301 489-17

z Article 3.2 Spectrum Usages

-. EN300 328

-. EN301 893 (Applicable to 5GHz high performance RLAN).

Year to begin affixing CE marking 2010.

_______________________________ Mar. 1, 2010 -

Easy Lai /Manager Date

Regulation Center, Acer Inc.

Acer America Corporation

333 West San Carlos St., San Jose

CA 95110, U. S. A.
Tel : [phone]

Fax : [phone]

www.acer.com

Federal Communications Commission

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.

The following local Manufacturer / Importer is responsible for this declaration:

Product: DLP Projector

Model Number: H7P0901

Machine Type: V700

Name of Responsible Party: Acer America Corporation

Address of Responsible Party: 333 West San Carlos St.

San Jose, CA 95110

U. S. A.

Contact Person: Acer Representative

Phone No.: 254-298-4000

Fax No.: 254-298-4147