Order codes: ELUM019
Kudos 700 Beam
User Manual
www.prolight.co.uk Kudos 700 Beam User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 100~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• Never touch the xture during operation as it may be hot.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This lighting xture is for professional use only - it is not
designed for or suitable for household use. The product
must be installed by a qualied technician in accordance
with local territory regulations. The safety of the installation
is the responsibility of the installer. The xture presents
risks of severe injury or death due to re hazards, electric
shock and falls.
• Warning! Risk Group 2 LED product according to
EN 62471. Do not view the light output with optical
instruments or any device that may concentrate the beam.
• High power lighting xtures are capable of producing
powerful, concentrated beams of light that can create a
re hazard or a risk of eye injury if the safety precautions
are not followed.
• WARRANTY: Two years from date of purchase.
www.prolight.co.uk Kudos 700 Beam User Manual
3
Safety advice
This xture falls under Protection Class 1, therefore it has to be connected
to a mains socket with a protective earthing connection.
Risk group 2, RG-2: CAUTION!
Do not stare at exposed LED in operation as it may damage/be harmful to
the eyes. Avoid looking directly into the light source.
CAUTION!
If the lens gets damaged ie. cracks or deep scratches so the output is impaired
then it must be replaced.
CAUTION!
The maximum ambient temperature (Ta) of 40° must not be exceeded.
CAUTION!
To avoid damage to internal parts ie. optics, colour lters, gobos, prisms, frost
lters, iris, shutters, motors, belts, wiring or LEDs never expose the front lens to
direct sunlight, lighting xtures or lasers even when the xture is not in use.
www.prolight.co.uk Kudos 700 Beam User Manual
4
Product overview & technical specications
• 1 x 110W white LED (7500K)
• Beam angle: 2°
• 20,000 Lux @ 10m
• 2kHz refresh rate
• Motorised focus
• 8 facet circular rotating prism plus
16 facet circular rotating prism
• Frost lter (12°)
• Gobo wheel: 17 xed gobos + open
• Colour wheel: 12 colours + 5600K + 3200K + open
• DMX channels: 12 or 18 selectable
• RDM (Remote Device Management)
• Manual modes
• Pan/tilt transit lock
• Pan/tilt auto correction
• 16-Bit pan/tilt positioning
• Pan: 540°, Tilt: 270°
• 0-100% dimming and variable strobe
• Quick release omega clamps included
• 4 push button menu with 1.8” LCD display
• PowerCON input/output
• 5-Pin XLR input/output
• Fan cooled
Kudos 700 Beam
Specications Kudos 700 Beam
Power consumption 157W
Fuse F2A 250V
Power supply 100~240V, 50/60Hz
Dimensions 534 x 327 x 222mm
Weight 14kg
Order code ELUM019
0m 5m 10m 15m 20m
2° - Lux 80000 20000 8890
2°
5000
The Kudos 700 Beam projects a tight 2° concentrated beam from its powerful 110W LED source. Inside the
ergonomic head are 2 circular rotating prisms (8 facet and 16 facet), 12 colours + 5600K + 3200K + open, 17
xed gobos + open, 12° frost lter and a motorised focus. The powerful beam cuts through haze with lightning-fast
speed, creating stunning aerial effects, drop in the frost lter and you can also achieve wash effects making it even
more versatile. RDM along with 16-bit pan/tilt positioning and smooth dimming are also included in this xtures
impressive features, along with all the fundamental characteristics you would expect from eLumen8, backed up
by a 2 year warranty.
www.prolight.co.uk Kudos 700 Beam User Manual
5
338mm
428mm
469mm
534mm
Technical specications
122mm
222mm 310mm
327mm
210mm
98mm
www.prolight.co.uk Kudos 700 Beam User Manual
6
Technical specications
01 - LCD display
02 - Function buttons
03 - 5-Pin DMX input
04 - 5-Pin DMX output
05 - PowerCON input
06 - PowerCON output
07 - Fuse F2A 250V
08 - Power switch
09 - Fans
In the box: 1 x xture,
2 x omega clamps,
1 x power cable
& 1 x user manual
09
08
01 0202 04 05 06 0703
09
www.prolight.co.uk Kudos 700 Beam User Manual
7
Installation
Before installing the xture, the supporting structure (ie. truss) must be able to hold a minimum of 10
times the xtures weight without any deformation (eg. 14kg - 140kg point load). The xture must be
secured with a secondary safety attachment when being installed (ie. an appropriate safety cable).
Never stand directly below the xture when mounting, removing, and/or servicing.
Overhead installation requires experience and qualications to calculate working load limits, the
material being used at the installation area and periodic safety inspections of the xture and installation
material. If you do not have the relevant experience and/or qualications please do not attempt the
installation yourself. The installation should be checked annually by a qualied person.
The eLumen8 Kudos 700 Beam can be operated in a number of mounting positions as shown in
the diagram above, hanging upside-down from the ceiling or truss, mounting sideways on truss or
stood upright on a at level surface. Always use a safety wire as an extra safety precaution to prevent
damage/injury in the event a clamp fails (see the next page for clamp installation).
Never use the carry handles for secondary attachments.
www.prolight.co.uk Kudos 700 Beam User Manual
8
Installation
Installation:
1. Fasten each clamp to the omega clamps with a bolt and lock nut through the hole in the
omega clamp.
2. Align and insert the omega clamp quick-lock fasteners with the respective holes on the bottom
of the unit.
3. Tighten both locking fasteners clockwise on each omega clamp ensuring they’re fully secure.
4. Mount the xture onto your truss system via the clamps and tighten to ensure secure.
5. Pull the safety cable through the safety cable holes located on the metal base plate on the
underside of the xture and around the truss.
1
2
4
5
3
www.prolight.co.uk Kudos 700 Beam User Manual
9
90°
90°
90°
90°
Pan/Tilt Lock Mechanism
LOCKED
UNLOCKED
Pan mechanism lock and release every 90°
LOCKED UNLOCKED
Tilt mechanism lock and release every 90°
90°
90°
www.prolight.co.uk Kudos 700 Beam User Manual
10
Operating instructions
Control Panel Menu:
The LCD control panel situated on the front of the xture allows the user to access the menu system to
adjust the xtures settings.
When the unit has been powered on the display will show “eLumen8 Kudos 700 Beam”, “System
Initialising...” whilst the unit performs its motor reset. The xture will then return to its home screen.
Pressing the “MENU” button once will take the user to the xtures main menu. Using the “UP” and
“DOWN” buttons you can then navigate between the different options in the main menu. Pressing the
“ENTER” button on one of these options allows you to access the sub menu where you can use the
“UP” and “DOWN” buttons to select option/value required. Once the option/value has been selected
press the “ENTER” button once more to conrm the setting.
To exit out of any of the above options, press and hold the “MENU” button.
Error Codes:
When the unit is powered on the unit will automatically perform a motor reset. If there is a problem
with any of the motors you will need to check the Error Log once the home screen appears.
To do this follow the instructions on page 17 (Error Log) to show what error has occurred.
Home Screen:
Please see the diagram below with a key to what the sections of the home screen mean.
MENU
ENTER
UP
DOWN
001
Kudos 700 Beam
SYS: Ready
CHL: 18CH
DMX: Fail
TEM: 28°C
02
05
04
01
03
01 - DMX Address - This can be adjusted in the DMX Address
Menu (see page 11).
02 - SYS: Ready - This indicates the unit is ready to use.
03 - CHL: - This is the DMX Channel mode the xture is
currently in, either 12CH or 18CH.
04 - DMX: This will either show Fail (there is no DMX signal)
or OK (there is DMX signal).
05 - TEM: - This shows the xture temperature.
www.prolight.co.uk Kudos 700 Beam User Manual
11
1) DMX
Address
2) Channel
Mode
3) DMX Fail
1) Address
xxx
1) 12Channel
1) Hold
2) 18Channel
2) Blackout
DMX address:
Please note: when there is no DMX signal
present the address will ash.
To access the DMX address mode, press the
“MENU” button on the front of the unit to show
“DMX Address” on the LCD display. Now
press the “ENTER” button and use the “UP”
and “DOWN” buttons to set the required DMX
address. Press the “ENTER” button to conrm
the setting.
Main Menu - Defaults are in grey
DMX channel mode:
To access the DMX channel mode, press the
“MENU” button on the front of the unit to show
“Channel Mode” on the LCD display. Now
press the “ENTER” button and use the “UP”
and “DOWN” buttons to set the required DMX
channel. Press the “ENTER” button to conrm the
setting.
DMX fail:
Sets what the xture does when the DMX signal
is lost. To access the DMX fail setting, press the
“MENU” button on the front of the unit to show
“DMX Fail” on the LCD display. Now press the
“ENTER” button and use the “UP” and “DOWN”
buttons to choose between “Hold” or “Blackout”.
Press the “ENTER” button to conrm the setting.
Operating instructions
Default
001
www.prolight.co.uk Kudos 700 Beam User Manual
12
4) Manual
Control
1) Pan
xxx
2) Tilt
xxx
3) Dimmer
xxx
4) Strobe
xxx
5) Colour
xxx
6) Gobo
xxx
7) Prism1
xxx
8) Prism 1 Rot
xxx
9) Prism2
xxx
10) Prism2 Rot
xxx
11) Frost
xxx
12) Focus
xxx
Operating instructions
Manual control:
To access manual control mode, press the
“MENU” button on to show “Manual Control”
on the LCD display. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to select
the various options. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to select
between “000” - “255”. Press the “ENTER” button
to conrm the setting.
Default
000
www.prolight.co.uk Kudos 700 Beam User Manual
13
Operating instructions
5) Auto Test
6) Motor Reset
1) Stop
1) Yes
2) Run
2) No
Auto test:
Tests all functions and motors in the xture.
To access the auto test mode, press the “MENU”
button on to show “Auto Test” on the LCD display.
Press the “ENTER” button and use the “UP”
and “DOWN” buttons to select between
“Run” and “Stop”. Press the “ENTER” button
to conrm the setting.
Please note: Auto test will automatically stop
when exiting the auto test menu.
Motor reset:
Resets all the xtures motors.
To access the motor reset setting, press the
“MENU” button on to show “Motor Reset” on the
LCD display. Press the “ENTER” button and use
the “UP” and “DOWN” buttons to select between
“Yes” and “No”. Press the “ENTER” button to
perform the motor reset when yes is selected.
7) P/T Invert 1) Pan Invert
2) Tilt Invert
1) ON
1) ON
2) Off
2) Off
Pan invert:
To access the pan invert setting, press the
“MENU” button on to show “P/T Invert” on the
LCD display. Press the “ENTER” button and use
the “UP” and “DOWN” buttons to select “Pan
Invert”. Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select between
“ON” and “Off”. Press the “ENTER” button to
conrm the setting.
Tilt invert:
To access the tilt invert setting, press the “MENU”
button on to show “P/T Invert” on the LCD
display. Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select “Tilt Invert”.
Press the “ENTER” button and use the “UP” and
“DOWN” buttons to select between “ON” and
“Off”. Press the “ENTER” button to conrm the
setting.
www.prolight.co.uk Kudos 700 Beam User Manual
14
Operating instructions
8) Blackout 1) BL.O P/T
2) BL.O Colour
2) BL.O Gobo
1) ON
1) ON
1) ON
2) Off
2) Off
2) Off
Blackout whilst pan/tilt:
Sets whether the xture blacks out whilst
panning/tilting.
To access the blackout whilst pan/tilt setting,
press the “MENU” button on to show “Blackout”
on the LCD display. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to select
“BL.O P/T”. Press the “ENTER” button and use
the “UP” and “DOWN” buttons to select between
“ON” and “Off”. Press the “ENTER” button to
conrm the setting.
Blackout whilst colour change:
Sets whether the xture blacks out whilst
changing colour.
To access the blackout whilst colour change
setting, press the “MENU” button on to show
“Blackout” on the LCD display. Press the “ENTER”
button and use the “UP” and “DOWN” buttons to
select “BL.O Colour”. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to select
between “ON” and “Off”. Press the “ENTER”
button to conrm the setting.
Blackout whilst gobo change:
Sets whether the xture blacks out whilst
changing gobo.
To access the blackout whilst gobo change
setting, press the “MENU” button on to show
“Blackout” on the LCD display. Press the “ENTER”
button and use the “UP” and “DOWN” buttons
to select “BL.O Gobo”. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to select
between “ON” and “Off”. Press the “ENTER”
button to conrm the setting.
www.prolight.co.uk Kudos 700 Beam User Manual
15
Operating instructions
9) Display 1) Backlight
2) Display
Inverse
1) Off
1) ON
2) On
2) Off
Display backlight:
Sets the display backlight.
To access the display backlight setting, press the
“MENU” button on to show “Display” on the LCD
display. Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select “Backlight”.
Press the “ENTER” button and use the “UP” and
“DOWN” buttons to select between “Off” and
“On”. Press the “ENTER” button to conrm
the setting.
Display inverse:
To access the display inverse setting, press the
“MENU” button on to show “Display” on the LCD
display. Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select “Display
Inverse”.Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select between
“ON” and “Off”. Press the “ENTER” button to
conrm the setting.
www.prolight.co.uk Kudos 700 Beam User Manual
16
Operating instructionsOperating instructions
10) Settings 1) Calibration
1) Pan
xxx
1) Yes
2) Tilt
xxx
2) No
3) Colour
xxx
4) Gobo
xxx
5) Prism1
xxx
6) Prism2
xxx
7) Frost
xxx
2) Factory Reset
8) Focus
xxx
Calibration:
Calibration settings for the xture.
To access the units calibration menu press the
“MENU” button once to display “Settings” on
the LCD display. Press the “ENTER” button and
use the “UP” and “DOWN” buttons to select
“Calibration”. Press the “ENTER” button and
use the “UP” and “DOWN” buttons to select the
various options. Press the “ENTER” button and
use the “UP” and “DOWN” buttons to select
between “000” - “255”.
Press the “ENTER” button to conrm the setting.
Please note: Calibration settings are set when
the xture is manufactured. This can be changed
manually for home position adjustment.
Performing a factory reset will not change these
settings.
Factory Reset:
Resets all the xtures factory settings.
To access the factory setting reset, press the
“MENU” button once to display “Settings” on the
LCD display. Press the “ENTER” button and use
the “UP” and “DOWN” buttons to select “Factory
Reset”. Press the “ENTER” button and use the
“UP” and “DOWN” buttons to select between
“Yes” and “No”. Press the “ENTER” button to
perform the factory setting reset when yes is
selected.
www.prolight.co.uk Kudos 700 Beam User Manual
17
Operating instructions
Fixture Time:
Displays the xtures total run time.
To display the xtures total run time, press the
“MENU” button once to display “Information”
on the LCD display. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to show
“Fixture Time(H)” on the LCD display. The unit will
now display the xtures run time.
Error Log:
Displays the xtures error log.
To display the xtures error log, press the “MENU”
button once to display “Information” on the
LCD display. Press the “ENTER” button and use
the “UP” and “DOWN” buttons to show “Error
Record” on the LCD display. Press the “ENTER”
button. The unit will now display the xtures
run time.
Fixture Information:
Displays the xtures version and RDM ID.
To display the xture information, press the
“MENU” button once to display “Information”
on the LCD display. Press the “ENTER” button
and use the “UP” and “DOWN” buttons to show
“About” on the LCD display. Press the “ENTER”
button. The unit will now display the xtures
software version and RDM ID.
11) Information
1) Fixture
Time(H): xxx
2) Error Record
3) About
xxx
Soft Version:
RDM ID:
www.prolight.co.uk Kudos 700 Beam User Manual
18
Operating instructions
12 channel mode:
Channel Value Function
CH1 000-255 Pan adjustment 0-540°
CH2 000-255 Tilt adjustment 0-270°
CH3 000-255 Pan/tilt speed (fast-slow)
CH4
000-004 Open
005-008 Open + Red
009-012 Red
013-017 Red + Orange
018-021 Orange
022-025 Orange + Cyan
026-029 Cyan
030-034 Cyan + Green
035-038 Green
039-042 Green + Lime Green
043-046 Lime Green
047-051 Lime Green + Lavender
052-055 Lavender
056-059 Lavender + Pink
060-063 Pink
064-068 Pink + Yellow
069-072 Yellow
073-076 Yellow + Magenta
077-081 Magenta
082-085 Magenta + Blue
086-089 Blue
090-093 Blue + CTO 260
094-098 CTO 260
099-102 CTO 260 + CTO 190
103-106 CTO 190
107-110 CTO 190 + CTB 8000
111-115 CTB 8000
116-119 CTB 8000 + Dark Blue
120-123 Dark Blue
124-127 Dark Blue + Open
128-255
Colour Wheel Rotation
(slow-fast)
Channel Value Function
CH5
000-003 Blackout
004-103 Strobe (slow-fast)
104-107 Open
108-207 Strobe Pulse (slow-fast)
208-212 Open
213-251 Random Strobe (slow-fast)
252-255 Open
CH6 000-255 Master dimmer (0-100%)
www.prolight.co.uk Kudos 700 Beam User Manual
19
Operating instructions
Channel Value Function
CH7
000-003 Open
004-007 Static gobo 1
008-011 Static gobo 2
012-015 Static gobo 3
016-019 Static gobo 4
020-023 Static gobo 5
024-027 Static gobo 6
028-031 Static gobo 7
032-035 Static gobo 8
036-039 Static gobo 9
040-043 Static gobo 10
044-047 Static gobo 11
048-051 Static gobo 12
052-055 Static gobo 13
056-059 Static gobo 14
060-063 Static gobo 15
064-067 Static gobo 16
068-071 Static gobo 17
072-113
Gobo wheel scroll CW
(fast-slow)
114-117 Rotation Stop
118-159
Gobo wheel scroll CCW
(slow-fast)
160-166 Gobo 2 shake (slow-fast)
167-172 Gobo 3 shake (slow-fast)
173-179 Gobo 4 shake (slow-fast)
180-185 Gobo 5 shake (slow-fast)
186-191 Gobo 6 shake (slow-fast)
192-198 Gobo 7 shake (slow-fast)
199-204 Gobo 8 shake (slow-fast)
205-211 Gobo 9 shake (slow-fast)
212-217 Gobo 10 shake (slow-fast)
218-223 Gobo 11 shake (slow-fast)
224-230 Gobo 12 shake (slow-fast)
231-236 Gobo 13 shake (slow-fast)
237-243 Gobo 14 shake (slow-fast)
244-249 Gobo 16 shake (slow-fast)
250-255 Gobo 17 shake (slow-fast)
12 channel mode cont.:
Channel Value Function
CH8
000-063 No function
064-127 8 facet circular prism
128-191 16 facet circular prism
192-255
8 facet circular prism +
16 facet circular prism
CH9
000-127 Prism location
128-191 Prism rotation CCW (fast-slow)
192-255 Prism rotation CW (slow-fast)
CH10 000-255 Frost
CH11 000-255 Focus
CH12
000-025 No function
026-076 Effects Motor Reset
077-127 Pan/Tilt Motor Reset
128-255 All Motor Reset
www.prolight.co.uk Kudos 700 Beam User Manual
20
Operating instructions
18 channel mode:
Channel Value Function
CH1 000-255 Pan adjustment 0-540°
CH2 000-255 Pan ne adjustment
CH3 000-255 Tilt adjustment 0-270°
CH4 000-255 Tilt ne adjustment
CH5 000-255 Pan/tilt speed (fast-slow)
CH6
000-004 Open
005-008 Open + Red
009-012 Red
013-017 Red + Orange
018-021 Orange
022-025 Orange + Cyan
026-029 Cyan
030-034 Cyan + Green
035-038 Green
039-042 Green + Lime Green
043-046 Lime Green
047-051 Lime Green + Lavender
052-055 Lavender
056-059 Lavender + Pink
060-063 Pink
064-068 Pink + Yellow
069-072 Yellow
073-076 Yellow + Magenta
077-081 Magenta
082-085 Magenta + Blue
086-089 Blue
090-093 Blue + CTO 260
094-098 CTO 260
099-102 CTO 260 + CTO 190
103-106 CTO 190
107-110 CTO 190 + CTB 8000
111-115 CTB 8000
116-119 CTB 8000 + Dark Blue
120-123 Dark Blue
124-127 Dark Blue + Open
128-255
Colour Wheel Rotation
(slow-fast)
Channel Value Function
CH7
000-003 Blackout
004-103 Strobe (slow-fast)
104-107 Open
108-207 Strobe Pulse (slow-fast)
208-212 Open
213-251 Random Strobe (slow-fast)
252-255 Open
CH8 000-255 Master dimmer (0-100%)
CH9 000-255
Master dimmer
ne adjustment
www.prolight.co.uk Kudos 700 Beam User Manual
21
Operating instructions
Channel Value Function
CH10
000-003 Open
004-007 Static gobo 1
008-011 Static gobo 2
012-015 Static gobo 3
016-019 Static gobo 4
020-023 Static gobo 5
024-027 Static gobo 6
028-031 Static gobo 7
032-035 Static gobo 8
036-039 Static gobo 9
040-043 Static gobo 10
044-047 Static gobo 11
048-051 Static gobo 12
052-055 Static gobo 13
056-059 Static gobo 14
060-063 Static gobo 15
064-067 Static gobo 16
068-071 Static gobo 17
072-113
Gobo wheel scroll CW
(fast-slow)
114-117 Rotation Stop
118-159
Gobo wheel scroll CCW
(slow-fast)
160-166 Gobo 2 shake (slow-fast)
167-172 Gobo 3 shake (slow-fast)
173-179 Gobo 4 shake (slow-fast)
180-185 Gobo 5 shake (slow-fast)
186-191 Gobo 6 shake (slow-fast)
192-198 Gobo 7 shake (slow-fast)
199-204 Gobo 8 shake (slow-fast)
205-211 Gobo 9 shake (slow-fast)
212-217 Gobo 10 shake (slow-fast)
218-223 Gobo 11 shake (slow-fast)
224-230 Gobo 12 shake (slow-fast)
231-236 Gobo 13 shake (slow-fast)
237-243 Gobo 14 shake (slow-fast)
244-249 Gobo 16 shake (slow-fast)
250-255 Gobo 17 shake (slow-fast)
18 channel mode cont.:
Channel Value Function
CH11
000-127 No function
128-255 8 facet circular prism
CH12
000-127 Prism location
128-191 Prism rotation CCW (fast-slow)
192-255 Prism rotation CW (slow-fast)
CH13
000-127 No function
128-255 16 facet circular prism
CH14
000-127 Prism location
128-191 Prism rotation CCW (fast-slow)
192-255 Prism rotation CW (slow-fast)
CH15 000-255 Frost
CH16 000-255 Focus
CH17
000-055 No function
056-105 Square Law
106-155 Linear
156-205 Inverse Square Law
206-255 S-Curve
CH18
000-025 No function
026-076 Effects Motor Reset
077-127 Pan/Tilt Motor Reset
128-255 All Motor Reset
www.prolight.co.uk Kudos 700 Beam User Manual
22
Static gobos:
Open Gobo 1 Gobo 2 Gobo 3
Gobo 4 Gobo 5 Gobo 6 Gobo 7
Gobo 8 Gobo 9 Gobo 10 Gobo 11
Gobo 12 Gobo 13 Gobo 14 Gobo 15
Gobo 16 Gobo 17
Operating instructions
www.prolight.co.uk Kudos 700 Beam User Manual
23
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”
from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104,
105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in
the chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.
DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”
XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest
cable path possible. The order in which xtures are connected in a DMX line does not inuence the
DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a
DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,
no matter where it is located in the DMX chain.
DATA cable (DMX cable) requirements (for DMX operation):
This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output,
see images below.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.
Please quote:
CABL10 – 2m CABL11 – 5m CABL12 – 10m3-Pin:
CABL185 – 2m CABL187 – 5m CABL188 – 10m5-Pin:
www.prolight.co.uk Kudos 700 Beam User Manual
24
Notice:
Be sure to follow the diagrams below when making your own cables.
Do not connect the cables shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLRs
outer casing. Grounding the shield could cause a short circuit
and erratic behaviour.
Line termination:
When longer runs of cable are used,
you may need to use a terminator on
the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90,
5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
Termination reduces signal
transmission problems and
interference. It is always
advisable to connect a DMX
terminal, (resistance 120
Ohm 1/4W) between pin 2
(DMX-) and pin 3 (DMX+) of
the last xture.
5-Pin
1
2 4
5
3
3-Pin
1 2
3
Pin Conguration
3-Pin 5-Pin
Pin 1 - Ground
Pin 2 - Negative
Pin 3 - Positive
– Pin 4 - N/C
– Pin 5 - N/C
1
2
3
1
2
3
DMX 512
3-Pin XLR output
DMX 512
3-Pin XLR input
GROUND
DMX +
DMX –
DMX 512
5-Pin XLR output
DMX 512
5-Pin XLR input
1
2
4
5
3
1
2
4
5
3
GROUND
N/C
DMX –
N/C
DMX +
1 ground
3 hot
2 cold
3-Pin XLR male 3-Pin XLR female
2 cold
3 hot
1 ground
2 cold
1 ground 5 N/C
3 hot
4 N/C
5-Pin XLR male 5-Pin XLR female
4 N/C
5 N/C 1 ground
3 hot
2 cold
www.prolight.co.uk Kudos 700 Beam User Manual
25
Multiple xture power linking
Power linking:
This xture provides power linking via the power output on the rear allowing multiple units to be
connected together. The maximum number of xtures that can be connected is 6 xtures @ 240V
or 3 xtures @ 120V (including the rst xture). After the maximum number of xtures are
connected a new power run will need to be started.
Please note: Caution should be used when power linking other xtures to the Kudos 700 Beam as the
power consumption of other xtures will vary. Fixtures tted with lamps often require 2/3 times more
current on startup, these may require their own power source.
Please contact your local retailer to purchase these accessories.
Replacement Omega Clamp
Order code: CLAM21
Optional accessories
www.prolight.co.uk Kudos 700 Beam User Manual
26
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.
www.prolight.co.uk Kudos 700 Beam User Manual
27
www.prolight.co.uk Kudos 700 Beam User Manual
28
Loading...