Elumen8 ELUM053 User Manual
ELUM053
User Manual
Please read the user manual before use
!!!
!
1!A!
!!!
!
2!A!
Table of Contents
1，Safety Information…………………………………………………. 3
2，Rear Panel…………………………………………………………. 5
3，Preparation for Use ………………………………………………...5
4，Main Functions ..…………………………… …………………….. 6
5，Remote Control…………………………………………………….10
6，Technical Specification…………………………………………….12
!!!
!
3!A!
1. Safety Information
Warning: This product is for professional u se only! It is not for
household use.
The Plasma 1K White presents risks of lethal or severe injury due to fire
and heat, electric shock, ultraviolet radiation, and falls. Flashing light is
also known to trigger epileptic seizures in persons who are
photosensitive. Read this manual before powering or installing the fixture,
follow the safety precautions listed below and observe all warnings in this
manual and printed on the fixture.
Noted: high voltage in the LED board!
High power strobes, so please avoid extended periods of
continuous flashing
To guard against electric shock
! Do not remove the rear cover: there are no user-serviceable parts inside.
! Always ground (earth) the fixture.
! Use only a source of AC power that complies with local building and electrical
codes and has both overload and ground-fault protection.
! Do not expose the fixture to rain or moisture.
To guard against UV radiation, burns, and fire
! Never operate the fixture with the front glass open, missing or damaged.
! Do not stare directly into the light. Never look at an exposed LED while it is lit.
! Never attempt to bypass the fuse. Always replace defective fuses with ones of the
specified type and rating.
! Verify that the power feed cable is rated for the current draw of all connected
fixtures.
! Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters
away from the fixture.
! Keep flammable materials well away from the fixture.
! Minimum distance to illuminated surface is 10 meters.
! Provide a minimum clearance of 30cm around fixture air vents.
! Never place filters or other materials over the front glass cover.
! The exterior of the fixture can reach high temperatures. Allow the fixture to cool for
!!!
!
4!A!
at least 15 minutes before handling.
! Do not modify the fixture or install anything other than genuine parts.
! Do not operate if the ambient air temperature (Ta) exceeds 40° C (104° F).
To guard against falls
! When suspending the fixture above ground level, verify that the structure can hold
at least 10 times the weight of all installed devices.
! Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
! Block access below the work area whenever installing or removing the fixture.
To guard against epileptic seizure
! Do not operate the fixture near stairways.
! Provide advance notice that strobe lighting is in use.
! Avoid extended periods of continuous flashing, particularly at frequencies of 10 to
20 flashes per second.
For AC 220-240V power supply, the maximum fixtures that can be connected on one
power cable is 6(including the first fixture) ;
For AC 100~120V power supply, the maximum fixtures that can be connected on one
power cable is 3 (including the first fixture).
!!!
!
5!A!
2. Rear Panel
1, POWER IN/OUT:
PowerCon connection from main power supply, and connection for main power
supply to the next unit.
2, Circuit Breaker: T6.3A
3. LED display
4, LED indicator:
Signal
Flash
Signal input present
Master
On
Master
Slave
On
Slave
Sound
Flash
Sound activation
5, Menu /UP/DOWN/ Enter button
6, DMX input/output
7, Microphone: Receive music signal for sound active mode
8, CA-8 Connector: Connect with easy controller CA-8
3. Preparation for Use
INSTALLATION
The Plasma 1K White may be installed in any orientation. The mounting bracket
provides five 12 mm holes for direct fastening or attachment of rigging clamps.
Loading...