1
Part Number: 980363-001 Rev.A
© Zebra Technologies Corporation
Welcome to your new
Eltron P205 (Monochrome)
& Eltron P210 (Color)
User’s Manual
2
FOREWORD
This manual contains installation and operation information for the Eltron P200 Series card printers manufactured
by Zebra Technologies Corporation.
RETURN MATERIALS AUTHORIZATION
Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-of-warranty repair, contact
Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original
packing material and mark the RMA number clearly on the outside. Ship the equipment, freight prepaid, to the
address listed below:
For USA and Latin America:
Zebra Technologies Corporation
Eltron Card Printer Products
1001 Flynn Road
Camarillo, CA. 93012-8706.USA
Phone: +1 (805) 579-1800
FAX: +1 (805) 579-1808
For Europe, Asia and Pacific:
Zebra Technologies Inc. France
Eltron Card Printer Products
Zone Industrielle, Rue d’Amsterdam
44370 Varades, France
Phone: + 33 (0) 240 097 070
FAX: + 33 (0) 240 834 745
COPYRIGHT NOTICE
This document contains information proprietary to Zebra Technologies Corporation. This document and the
information contained within is Copyrighted by Zebra Technologies Corporation and may not be duplicated in full or
in part by any person without written approval from Zebra. While every effort has been made to keep the
information contained within current and accurate as of the date of publication, no guarantee is given that the
document is error-free or that it is accurate with regard to any specification. Zebra reserves the right to make
changes, for the purpose of product improvement, at any time.
TRADEMARKS
Eltron is a registered trademark of Zebra Technologies Corporation. Windows and MS.DOS are registered trademarks
of Microsoft Corp. All other trademarks or registered trademarks are marks of their respective holders.
3
WARRANTY INFORMATION
WE NEED TO HEAR FROM YOU!
To establish your warranty period and provide access to technical support, please register now, on Eltroncard ’s web
site or send us your warranty registration card today!
Zebra warrants the mechanism, control electronics and power supply, under normal use and service, to be free from
defects in material and workmanship for a period of twelve (12) months from the date of purchase by the end user.
If proof of purchase or product registration cannot be established, shipment date to the original buyer (dealer or
distributor) will be used to establish the warranty period.
Since printhead wear is part of normal operation, a replacement printhead is covered by a limited warranty of
twelve (12) months or 100,000 passes (whichever occurs first )from the date of printhead installation or date of
printhead shipment from ZEBRA. To qualify for the printhead warranty, the printer or printhead must be returned to
the factory or other authorized service center.
Although the user is not required to purchase ZEBRA brand supplies (media and/or ribbons), to the extent it is
determined that the use of other supplies (media and/or ribbons) shall have caused any defect in the printhead for
which a warranty claim is made, this limited warranty shall be null and void and the user shall be responsible for
ZEBRA’s current charges for labor and materials to repair such defect. To the extent that it is determined that failure
to follow the preventive maintenance schedule and procedures listed in the Operator’s Guide shall have caused any
defect in the printhead for which a warranty claim is made, this limited warranty shall be null and void and the user
shall be responsible for ZEBRA’s current charges for labor and materials to repair such defect.
Failure to exercise caution to protect the equipment from electrostatic discharge damage, adverse temperature and
humidity conditions or physical abuse, including, but not limited to, improper packaging, shipping, service or repairs
performed by personnel not authorized by Zebra may void the warranty. Zebra will, at its option, repair or replace
the equipment or any parts which are determined to be defective within this warranty period, and which are
returned to Zebra.
The warranty set forth above is exclusive and no other warranty, whether written or oral, is expressed or implied.
Zebra specifically disclaims the implied warranties of merchantability and fitness for a particular purpose.
4
DECLARATIONS OF CONFORMITY
Supplemental Information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmfull
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
73/23/EEC modified
by 93/68/EEC
EMC Directive
EN 500082-1,1992
Immunity to
Electromagnetic
Disturbances
European Council Directive
Compliance to Standards
89/336/EEC
modified by
92/31/EEC and
93/68/EEC
RF Emissions
control
Low voltage
Directive
EMC Directive
EN 60950
EN 55022-B
Product safety
Model: P210 conforms to the following specification:
FCC Part 15, Subpart A, Section 15.107(a) and Section 15.109(a)
Class A digital device
5
INTRODUCTION
Thank you for choosing the Eltron P210 Plastic Card Printer.
Eltron’s P200 series card printers offer a low cost, high quality solution to those requiring computer-controlled
printing and encoding of credit card style plastic cards. Card applications include customer loyalty, access control,
visitor, membership, gift cards, durable business cards.
This manual guides you to efficient start up and operation of your new Card Printer.
P210/P205 PRINTER MODELS
The Eltron Product Number tells a story:
Here is a quick review of the Eltron Card Printer Series numbering and lettering system to help you.
The P210 Plastic Card Printer employs Dye Sublimation and Resin Thermal Transfer technologies. Model numbers
include identifiers that specify options using the following lettering conventions:
Smart Card:
O = No
Magnetic Encoder:
O = No
M = Yes
Magnetic Encoder Options:
O = No
1 = Stripe down HICO
2 = Stripe Down LOCO
3 = Stripe Up HICO
4 = Stripe Up LOCO
Memory:
O = Standard
Interface:
U= USB / Parallel
R= USB / Serial
}
Ship-away kit
P210C - 0 X X 0 X - X D
Windows Drivers & User Documentation CD:
D= Drivers & Documentation
Power Cord:
O = None
A = 120 VAC
E = 220 VAC
U = UK
6
ICONS
Throughout this manual, different icons highlight important information, as follows:
Important general information.
Mechanical hazard, such as one associated with moving parts, capable of resulting in equipment
damage or personal injury.
Electrical hazard, such as an exposed voltage point, capable of causing electrical shock and
personal injury.
An area where electrostatic discharge (ESD) can cause component damage. Use a grounding
wrist band.
Elevated temperature hazard, capable of producing a burn.
Keep Card Printer clean by minimizing cover open time.
7
1
2
3
4
5
TABLE OF CONTENTS
GETTING STARTED • • • • • • • • • • • • • • • • • • • • • 9
1•1 Unpacking your P210 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 9
1•2 Indicators and control • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 11
1•3 Printer installation • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 12
OPERATION • • • • • • • • • • • • • • • • • • • • • • • • • 13
2•1 Printer Features • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 13
2•2 Loading ribbon cartridge • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 14
2•3 Loading cards • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 15
A- Card Feeder • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 15
B- Card Cleaning Cartridge • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 16
2•4 Feeding one card at a time • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 17
2•5 Printing a test card • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 18
PRINTING A SAMPLE CARD • • • • • • • • • • • • • • • • • 19
3•1 Install Driver on windows 95/98/ME • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 20
3•2 Install Driver on windows 2000 & NT4.0 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 21
3•3 SetPrinter Driver Option • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 21
3•4 printing a sample card • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 22
CLEANING • • • • • • • • • • • • • • • • • • • • • • • • • • 23
4•1 Cleaning system • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 24
4•2 Cleaning the print head • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 25
4•3 Card Cleaning cartridge • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 26
TROUBLESHOOTING • • • • • • • • • • • • • • • • • • • • 28
5•1 Print Quality Issues • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 28
8
6
TECHNICAL SPECIFICATIONS • • • • • • • • • • • • • • • • 32
APPENDIX A - MAGNETIC CARD STRIP • • • • • • • • • • • 36
Introduction • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 36
A- Media Loading orientation • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 37
B- Magnetic Encoder Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 38
APPENDIX B - ACCESSORIES & SUPPLIES • • • • • • • • • • 40
Ribbon Cartridges • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 40
Cards • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 41
Accessories • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 42
WORLD WIDE SALES & SUPPORT • • • • • • • • • • • • • • 43
9
1
GETTING STARTED
1 • 1 Unpacking your card printer
Your P210 printer ships in a carton and protective anti-static bag. Keep all packaging material in case you need to move
or re-ship the printer.
Pull your printer out of the carton by grabing it on both side.
While unpacking, inspect the carton to ensure that no damage occured during shipment.
Please ensure that you have a clean and nearly dust free environment for proper operation and storage of the printer.
10
Make sure the following items are included with your P210 printer:
If any items are missing, please contact your dealer.
To reorder, please refer to Appendix C of this manual.
EXTERNAL POWER SUPPLY
PRINTER DRIVER &
USER’S MANUAL CD
POCKET GUIDE
CLEANING CARTRIDGE
INTERFACE CABLE
11
1 • 2 Indicators and Control
Your P210/P205 printer is equiped with a Multi Function Panel Button with a surrounding light ring that glows in three
colors to provide printer status indication.
The Multi Function Panel Button is used to perform the following operations:
- Clear Error
- Cleaning process (see chapter 4)
- Test Card (see chapter 2)
Power Switch:
The Power switch is located on the right-rear of the printer unit.
ON
FLASHING
POWER ON
READY
RIBBON OR CARD OUT
HARDWARE
OR FATAL ERROR
Refer to troubleshooting
COMMUNICATION ERROR
CLEANING
RECEIVING DATA
PROCESSING
Green
Orange
Red
12
1 • 3 Printer Installation
The following will guide you through the installation of your P210/P205 printer.
CAUTION: Limit AC power supplied to the P210/P205 Printer to 24 VDC. Limit
excess current draw to 16 amps or less, using an associated circuit breaker or
other such device. Never operate the printer in a location where operator,
computer, or printer can get wet. Personal injury could result. The printer must be
connected to an earthed electrical power supply and properly protected against
electrical surges and grounding faults. The power supply pack can only be
replaced by the same product from the constructor.
1 • Place the printer in a location that allows easy access to all sides. The printer
should never be operated while resting on its side or upside down.
2 • Place the printer
’s power switch in the OFF “O” position.
3 • Insert the power supply to the printer power socket “1” and attach to grounded
electrical socket of the proper voltage and type.
4 • Attach interface cable “2” to printer and computer and then secure.
5 • Switch power on.
CAUTION: Intermittent or unpredictable operation may occur from unsecured
connectors. If damaged, the power cable must be replaced by an exact
equivalent. Use only Parallel Cable under 3 Meters in length.
1
2
0
13
2
2 • 1 Printer Features
The following shows the features found on your P210 Printer:
Cover Release Buttons
Print Head
Card Cleaning Cartridge ( under the Ribbon Cartridge)
Ribbon Cartridge
Power switch
Multi Function Panel Button and Indicator Light
Card output hopper
Card Feeder & manual card feed
OPERATION
Magnetic Encoder Station (optional)
14
2 • 2 Loading Ribbon Cartridge
The P210 Printer requires approved ribbon cartridges (see Appendix C). The Resin Thermal Transfer and Dye
Sublimation ribbons are specifically designed for your P210 Printer. For optimum performance and printer life
(Print Head), always use approved ribbons.
You can print up to 100 cards in YMCKO with the ribbon cartridge.
When ribbon is completely used change the whole cartridge assembly.
DO NOT TOUCH the print head or the electronic components on the print head
carriage. Discharges of electrostatic charge from the human body or other surfaces
can damage the print head or other electronic components used in this device.
1 • Open printer cover by pressing both Cover Release buttons on the sides of your printer.
2 • Insert vertically the ribbon cartridge into the slot and press gently until you can feel it engage properly.
Please note that the ribbon automatically synchronizes.
15
2 • 3 Loading Cards
To help you load, print, and collect cards, the P210 has the following items:
A - CARD FEEDER
This item is used for loading cards, it can hold up to 50 cards of 30 mils.
You may have to install the Card Feeder.
Hold the card feeder on the sides and slide it into the rail guide.
• Install Cards into feeder at the front of your P210 printer.
For Cards with magnetic stripe refer to Appendix A for loading instructions.
DO NOT bend cards or touch print surfaces as this can reduce print quality.
The surface of the cards must remain clean and dust free. Always store cards in an
enclosed container. Ideally, use cards as soon as possible. If cards stick together,
carefully shuffle them.
* See Chapter 6, Technical Specifications, for card requirements and capacities.
16
B - CARD OUTPUT HOPPER
1 • Press on the card output hopper door and pull it down to place it in its functional position.
When not using the printer place the card output hopper back in its closed position to protect the printer from dust.
17
C - INSTALL CARD CLEANING CARTRIDGE
This item is used to clean the cards entering the printer.
It must be installed before using the printer.
*Improper cleaning will reduce printer life and degrade print quality.
1 • Open the lid by pressing both Cover Realese buttons located on the sides of your printer.
2 • If the ribbon cartridge is installed, remove it to access the cleaning cartridge location.
3 • Remove Card Cleaning Cartridge from plastic bag. Peel off protective wrapper from adhesive cleaning roller.
4 • Install adhesive cleaning roller supplied with your ribbon cartridge.
5 • A slide rail will guide you to insert the Cleaning Cartridge in the appropriate location.
A Cleaning Cartridge diagram is visible on the inside of your printer to help you find the appropriate location.
6 • Ensure the assembly locks in place by pressing gently on the top of the cartridge until it engages properly.
7 • Close the lid by pressing down firmly on both sides until you hear audible “clicks” as each side becomes latched.
18
2 • 4 Feeding one card at a time
For feeding one card at a time, like Cleaning Cards for example, remove all cards from card feeder and insert one card
at a time at the bottom of the feeder.
Do not feed more than one card at a time.
19
2 • 5 Printing a Test Card
With ribbon cartridge and cards loaded, your P210 printer is ready to print. To check the operation of the printer,
you should print a test card.
1 • Place the printer’s power switch in the OFF (0) position.
2 • While holding down the Multi Function Panel Button, switch printer ON (1). The status indicator will glow green.
3 • Keep pressing the Multi Function button until the green indicator starts flashing.
3 • Release the Multi Function button and a test card will print after a few seconds.
This is an example of the test card.
P210
Head resistance: 1568
Offset: X002 - Y015
EC : 0014
Printing counter:!00002716
V1.50
20
3
PRINTING A SAMPLE CARD
Printing with the P210 Printer requires the Windows Printer Driver, your card design/issuing software or printer
command level programming through the printer interface.
The P210 Card Printer can be used with any Windows 95/98/M.E, Windows 2000 or Windows NT 4.0 software application
program, using the drivers provided on CD with the printer.
This section contains information on the printing of a sample card in color (using the 5-Panel color ribbon YMCKO) and
the Windows Printer Driver.
BEFORE installing updated printer driver versions, always delete the existing printer
driver version from your computer.
21
3 • 1 To install the P210 Printer Driver in
Windows 95/98/M.E., use the following steps:
IMPORTANT NOTE: Ensure that your PC printer port is set to standard mode and also
ensure that you have deleted any previous versions of this printer driver. If you have
any doubts please contact your IT department.
An automatic installation software is provided with your CD ROM, select “DRIVERS” and follow the instructions.
You can also install your drivers manualy according to the following procedure:
This installation uses floppy drive “A” or from CD Rom as the installation drive with the printer used as stand alone.
1• Start your computer and then Windows.
2• Insert your “Eltron Software” diskette into the drive “A” or CD drive.
3• Under windows click the Start button, select Settings, then Printers.
4• Double click on the Add Printer icon and also Next.
5• Ensure Local Printer is selected and click on Next.
6•
Click on Have disk and then type in “A:\win98” if using the floppy disc or“D:\win98” if using the CD and click OK.
7• P210 CARD PRINTER should be displayed after which click on Next.
8•
Choose LPT1: Standard Printer Port, click on Next, select Ye s to set as Default Printer and click on Finish to install.
The Printer wizard will copy the necessary files to the PC for you and the P210 printer driver installation will be
completed.
22
3 • 2 To install the P210 Printer Driver in
Windows 2000/NT4.0:
Ensure that you have administrative privileges to perform this installation or contact
your IT department.
An automatic Installation sof
tware is provided with your CD ROM, select “DRIVERS” and follow the instructions.
Use the steps provided for windows 95/98/ME installation with the exception of step 6. Where you must type in
“A:\nt40” for NT4.0, “A:\winNT4”for Windows 2000 if using the floppy disc, or “D:\nt40” , “D:\winNT4” if using the
CD, instead and click OK.
Once the printer driver has been successfully installed, you will need to configure it for your printer. This driver provides
control of several printer features when printing from Windows applications. These features are accessed through the
P210 Plastic Card Printer Properties. To access these properties select the P210 Card Printer icon in Printers. Then click File
Menu and select Properties.
3 • 3 Set Printer Driver Options:
The P210 Printer screen appears. Change the options as follows:
1• On the Printer tab configure the magnetic encoder feature. If your Printer is equipped with a Magnetic Encoder
option, select With Magnetic Encoder option.
2• On the Card tab select card orientation:
Landscape or portrait - Select “Landscape”.
3• On the Ribbon tab, select the Ribbon Type. Select YMCKO for the standard 5-panel ribbon cartridge.
4• In the same tab, go to Black Panel area and select Text Only. This option allows the text printing using the Black
Resin Panel from the Color Ribbon.
5• Close the Eltron P210 Printer Properties screen.
Now that you have loaded media and set up the printer driver, the P210 Printer is ready to print.
23
3 • 4 Printing a sample card:
Follow the steps to print your first card
1• Go to the Microsoft Word Software.
2• If the printer was not selected as the default printer, go to the file menu and Select Printer and choose Eltron
P210 Card Printer
in the printer names list. Then Close the print dialog box.
3• Come back to file menu and choose Page Setup.
4• Select Size tab and in Paper Size choose Card. Then select the orientation: “landscape”.
5• Go to Margins tab, Set the Top, Bottom, left and right margins to O (zero) values (for P210 only).
6• Press OK to close Page Setup window.
7• The card appears on the screen.
8• Design a card with both black and colored text and with colored pictures (for P210 printer only) as follow:
9• Once you are ready to print, go to File and select Print
10• The printer will feed in a card and start printing (the data download time will vary depending on the
complexity of the card design and the processing speed of the computer).
11• Once the printing job is achieved the card is ejected from the printer.
24
4
CLEANING
PROTECT YOUR FACTORY WARRANTY!
The recommended maintenance procedures must be performed to maintain your
factory warranty. Other than the recommanded cleaning procedures described in this
manual, allow only Zebra authorised technicians to service the P210 Printer.
NEVER loosen, tighten, adjust, or bend, etc. a part or cable inside the printer.
NEVER use a high pressure air compressor to remove particles in the printer.
25
4 • 1 Cleaning System
Your P210 Printer includes a simple cleaning system using Pre-Satured Cleaning Cards provided. The regular use of
these cards will clean and maintain important parts of your printer that cannot be reached: including the Print Head
the Transport Rollers and Magnetic Encoder Station (optional feature).
WHEN TO CLEAN
Every 1000 cards approximately using 5-panel color ribbon cassette.
HOW TO CLEAN
1 • Leave power on.
Press on both sides the Cover Release buttons to open cover and remove ribbon cartridge.
Close Cover. Remove cards from Card Feeder.
2 • Insert one Pre-Saturated Cleaning Card through the bottom slot of the Card feeder.
3 • Press the multi function control button for a few seconds. The card will feed into the printer and carry out the
cleaning process.
Repeat the process with a new Cleaning card if necessary.
26
4 • 2 Cleaning the Print Head
A cleaning using the cleaning system with cards usually suffices. However, a separate Print head cleaning using swabs
can remove more stubborn deposits when print anomalies persist. To avoid deposits, only use foam-tipped swabs.
1 • Switch power Off, open cover by pressing both cover release buttons and remove the Ribbon Cartridge.
2 • Clean Print Head by moving alcohol-moistened swab tip side-to-side across Print Head elements. Only use
moderate force.
Make sure the elements are dry before switching on.
(To reorder swabs see Appendix C).
Never use a sharp object to scrape deposits from the print head. Permanent
damage will result.
27
4 • 3 Card Cleaning Cartridge
Your P210 Printer also has a Card Cleaning Cartridge. This item cleans the cards entering the printer. To ensure print
quality, the cleaning roller should be replaced with every ribbon cartridge replacement
WHEN TO MAINTAIN
Each time the ribbon cartridge is replaced.
If you plan to run a printer cleaning, do so before replacing the cleaning roller.
(see 4.1 Cleaning System for more instructions).
HOW TO MAINTAIN
1 • Turn power off.
Open Cover by pressing on both sides on the Cover Release buttons. Remove ribbon cartridge.
2 • Gently remove Cleaning Cartridge by pressing the cartridge’s arms on both sides and pulling up .
28
3 • Lift the cartridge lid up and remove the Adhesive Cleaning Roller from the cartridge and discard.
4 • Carefully peel off wrapper from new Cleaning Roller.
5 • Install new Cleaning Roller into the Cartridge*. To avoid contamination, always hold the Cleaning Roller assembly
by the ends.
6 • Replace Cleaning Cartridge into printer following the rail guides. Ensure the assembly locks in place.
DO NOT touch the roller surface that contacts the cards.
7 • Re-insert the Ribbon Cartridge
8 • Close Cover by pushing firmly down on both sides.
¨See Appendix C for replacement Cleaning Rollers.
5
29
TROUBLESHOOTING
This section offers solutions to potential problems you may experience with your P210 printer.
5 • 1 Print Quality Issues
This section will help you resolve print quality problems. The print quality is dependent on
several factors. The two most important factors that will increase your print quality are
cleanliness and card stock. To diagnose and fix print quality problems, follow the
troubleshooting procedure below:
30
• Small spots appear on the printed card with a non-printed area or a different color.
Possible Cause
A • Contamination on the card surface.
B • Dust inside the printer and/or dirty Cleaning Roller.
>> Solution
A1 • Check that cards are stored in a dust free environment
A2 • Use a different supply of cards.
B1 • Perform a Cleaning of the printer (see Cleaning section 4.1 Cleaning system & 4.3 Card Cleaning Cartridge).
B2 • Replace Cleaning Roller (see Cleaning section 4.3 Card Cleaning Cartridge)
• There are non-printing horizontal lines (white) on the card surfaces.
Possible Cause
A • Ribbon cartridge is not correctly positioned.
B • Print Head may be dirty.
C • Print Head elements may have been damaged
(e.g. scratched or burnt).
>> Solution
A1 • Open cover and replace ribbon cassette, make sure it locks in place.
A2 • Check that the ribbon is properly rolled onto the ribbon cores of the cartridge and that there are no wrinkles
in the ribbon.
A3 • Push down firmly on both sides of the cover until the lid engages properly.
A4 • Ribbon will automatically synchronize.
A5 • Print again.
B1 • Perform a Cleaning of the Print Head (see 4 • 2 Cleaning the Print Head).
C1 • Call service for Print Head replacement information.
31
• Printing shows very pale or inconsistent results.
Possible Cause
A • Ribbon cartridge have been stored improperly or is damaged.
B • Cards may not meet specifications.
C • Contrast and/or Intensity may be set to values which are too high.
D • Dust or embedded contamination on elements of the Print Head.
>> Solution
A1 • Change ribbon cartridge and print again.
B1 • Use a different supply of cards.
C1 • Adjust Contrast and/or Intensity values in software.
D1 • Perform a Cleaning of the Print Head (see 4 • 2 Cleaning the Print Head
• Printing shows blurry printed image.
Possible Cause
A • Ribbon cartridge may not be correctly positioned.
B • Ribbon may not be synchronized on the correct color panel position.
C • Cards may not meet specifications.
D • Dust inside the printer and/or dirty Cleaning Roller.
>> Solution
A1 • Open cover and replace ribbon cartridge, make sure it locks in place.
A2 • Check that the ribbon is properly rolled onto the ribbon cores of the cartridge.
A3 • Push down on the cover until the lid engages properly.
A4 • Ribbon will automatically synchronize.
A5 • Print again.
B1 • Open cover and replace ribbon cartridge, make sure it locks in place.
B2 • Push down on the cover until until the lid engages properly.
B3 • Ribbon will automatically synchronize.
B4 • Print again.
C1 • Use a different supply of cards.
D1 • Perform a cleaning of the Print Head (See 4 • 2 Cleaning the Print Head).
D2 • Replace Cleaning Roller (See 4 • 3 Card Cleaning Cartridge).
32
• No printing on the card.
Possible Cause
A • Ribbon cartridge may not be installed in the printer.
B • Cards may not meet specifications.
C • Cable on Print Head may be disconnected.
D • Print Head elements may be scratched or burnt.
>> Solution
A1 • Check for ribbon cartridge in the printer.
B1 • Use a different supply of cards.
C1 • Power off the printer and check the Print Head cable connections.
D1 • Call Service for Print Head replacement information.
For optimum print quality, always keep cover of the printer closed.
33
6
TECHNICAL SPECIFICATIONS
General • High speed printing
40 seconds per card in YMCKO
4 seconds per card in Monochrome
• Small footprint
• Windows Drivers for 95/98/2000/ME and NT 4.0
• One year printer warranty
• One year (100,000 passes) print head warranty`
• Powerful EPCL (Eltron Printer Command Language)
Color Printing • Color dye sublimation or monochrome thermal transfer printing
• 300 dpi (11.8 dots/mm) print resolution
• Edge to edge printing standard (P210 only)
• 40 seconds per card edge to edge in full color (YMCKO)
Bar Code • Code 39
• Code 128 B & C with & without check digit
• 2 of 5 & 2 of 5 interleave
• UPCA
• EAN8 &EAN13
Fonts • Resident: Arial Normal 100, Arial Bold 100
• Flash memory supports download of different fonts.
• True Type fonts available via Windows Driver
Cards • Types PVC, Composite
• Card width/length: ISO CR-80 - ISO 7810,
2.125” (54mm) by 3.375” (86mm)
• Option: Magnetic Stripe - ISO 7811
• Card thickness: 10mil (0,25mm) to 30mil (0,75mm)
• Card Feeder capacity: up to 50 cards (30mil)
• Card Output Hopper capacity: 20 cards (30mil)
34
Ribbons Cartridges • Black Monochrome: 500 cards/cartridge
• YMCKO dye sub: 100 cards/cartridge
Interfaces • USB port / Parallel
• USB port / Serial
Mechanical • Width: 7.18” (182,4mm)
• Depth: 11.92” (303mm)
• Height: 7.03” (178,8mm)
• Weight: 6.39 Ibs (2,9 kg)
Electrical • 11 0 ~ 230 Volts AC, 60 ~ 50 Hz
• FCC Class A, CE, UL, and CUL approved
Environmental • Operating Temperature: 60 to 86°F (15 to 30°C)
• Operating Humidity: 20 to 65% non condensing
• Storage Temperature: -23 to 158°F (-5 to 70°C)
• Storage Humidity: 20 to 70% non condensing
• Ventilation: Free air
Options • Magnetic Encoder (0.76mm cards only)
• Cleaning supplies
35
CARD DIMENSIONS
ISO STANDARD DIMENSIONS FOR PLAIN CARD
ISO STANDARD DIMENSIONS FOR MAGNETIC STRIPE CARD
36
CHIP POSITION FOR SMART CARD
37
A
APPENDIX
Magnetic Card Stripe Encoder
This section contains information on the additional operations of the P210 Printers with Magnetic Card Stripe
Encoder.
(See Chapter 2 for location.)
INTRODUCTION
Operation and maintenance requirements for the P210 Printer with the optional magnetic card stripe encoder.
(See Chapter 2 for location.)
The magnetic encoder can be set for either high or low coercivity.
38
A • MEDIA LOADING ORIENTATION
The magnetic encoder is a factory installed item with the read/write head positioned
below the card path, available with HICO encoding or LOCO encoding.
When loading cards into the Card Cartridge, please ensure that the magnetic stripe is
facing down and closest to the right.
Note:
M1 = Stripe Down HICO M3 = Stripe up HICO
M2 = Stripe Down LOCO M4 = Stripe up LOCO
approved HICO & LOCO PVC cards are available. (See Appendix C).
ONLY USE cards that comply with ISO 7810 & 7811 standards for magnetic stripe
cards. The magnetic stripe must be flush to the surface of the card to work properly.
Never use cards which have taped-on magnetic stripes.
39
B • MAGNETIC ENCODER CLEANING
Use the standard cleaning card process.
. This cleans the most important parts of the printer; including the print Head, Transport Roller and Magnetic Stripe
Encoder (refer to chapter 4 “Cleaning” for more instructions.)
1 • Leave power on.
2 • Remove cards from the card feeder.
3 • Insert one presaturated card (provided) through slot on the side of the Card Cartridge.
4 • Press the Multi function button.
ISO STANDARD ENCODING
Track # Field Separator Track density Valid Characters # of characters
1^210BPI* Alphanumeric 79***
(ASCII 20 - 95**)
2=75BPI* Numeric 40***
(ASCII 48 - 62)
3=210BPI* Numeric 107***
(ASCII 48 - 62)
* Bit per inch
** Except the “?” character
*** Including Start, Stop and LRC characters. Also note that these 3 characters are
automatically managed by the magnetic encoder according to the ISO Standard norms.
NOTE: Refer to the Card Printer Programmer’s Manual for complete programming information.
40
B
Part Number Description Cards/Cartridge
800015-201 Black Monochrome 500
800015-240 5 Panel YMCKO Dye Sub 100
APPENDIX
Accessories & Supplies
Please contact your Eltron authorised dealer to place an order for accessories and supplies.
RIBBONS:
Use only Zebra-approved card, ribbon and patches media. Using nonapproved card or ribbon media can void your warranty.
Refer to the Accessories section for more information about Card and Ribbon
Media available from Zebra Technologies Corp.
Part Number Description : Starter Kit
105912-294 YMCKO Ribbon Cartridge + Cleaning Roller+ 100 PVC Cards
41
CARDS:
Part Number Description Card/pack thickness
104523-114 premier grade PVC 100 10mil
104523-111 premier grade PVC 100 30mil
104523-112 premier grade PVC LoCo 100 30mil
104523-113 premier grade PVC HiCo 100 30mil
104524-101 premier plus grade composite 100 30mil
104524-102 premier plus grade composite LoCo 100 30mil
104524-103 premier plus grade composite HiCo 100 30mil
42
ACCESSORIES
Accessories available for P210 printers appear below. Always refer to the part number when placing an order.
Printer supplies
Part Number Description
300320-001 Centronics Parallel cable (36 pins)
105912-212 USB Cable (6ft A-B)
105925-001 Replacement Print Head Kit
Cleaning Supplies
Part Number Description
105909-169 Premier Cleaning Kit (25 swabs, 50 cards)
105912-301 Adhesive Cleaning Roller Kit (set of 5)
105912-302 Cleaning Cartridge, complete
105909-055 Cleaning Card Kit (box of 100 cards)
105909-057 Cleaning Swab Kit (box of 25 swabs)
Miscellaneous
Part Number Description
105576-002 CD ROM (Software, Windows Drivers, Documentation)
806503-001 Card Punch (slots card for lapel clip)
104527-001 Lapel Clips (pack of 100 clips)
43
World Wide Sales and Support:
Zebra Technologies Corporation
Eltron Card Printer Products
1001 Flynn Road
Camarillo, CA 93012-8706.USA
Phone: + 1(805) 579 1800
Fax.: + 1 (805) 579 1808
Toll Free in US: (800) 452-4056
e-mail: cards@eltron.com
Zebra Technologies Corporation
Eltron card Printer Products, (Europe, Middle East, Africa)
The Valley Centre, Gordon Road, High Wycombe
Buckinghamshire HP13 6EQ, England
Phone: + 44 (0) 870 241 1527
Fax.: + 44 (0) 870 241 0765
e-mail: eurosales@eltron.com
Zebra Technologies France
Eltron card Printer Products, France
50, 56 rue Marcel Dassault
92100 Boulogne-Billancourt, France
Phone: + 33 1 55 20 93 93
Fax.: + 33 1 55 20 93 99
e-mail: frsales@eltron.com
Zebra Technologies Corporation
Eltron card Printer Products, Latin America
6175 NW 153 rd Street, Suite # 121
Miami Lakes, FL 33014 USA
Phone: + 1 (305) 558 8470
Fax: + 1 (305) 558-8485
e-mail: latinsales@eltron.com
Zebra Technologies Corporation
Eltron Card Printer Products, Asia/Pacifique
1 Sims lane # 06-11
387355 Singapore
Phone: + 65 84 20 322
Fax.: + 65 84 20 514
e-mail: asiasales@eltron.com
CORPORATE HEADQUARTERS
Zebra Technologies Corporation
333 Corporate Woods Parkway
Vernon Hills, IL 60061-3109 USA
Phone: 1 (847) 634 6700
Fax.: + 1 (847) 913 8766
e-mail: sales@Zebra.com
Loading...