Elsist MISSION 1000, MISSION 3000, MISSION 2000 Instruction Manual

Uninterruptible Power Systems

Mission 1K-2K-3K

Single Phase UP S

INSTRUCTION MANUAL

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 2

Contents

1.Safety instruction ........................................................................................................................................ 3

1.1 Safety instruction ................................................................................................................................... 3

1.2 Symbols indication ................................................................................................................................ 3

2.Product Introduction ................................................................................................................................... 4

2.1 The appearance of the product ............................................................................................................. 4

2.2 The principle of the product ................................................................................................................... 5

2.3 Model ..................................................................................................................................................... 5

3.Installation .................................................................................................................................................... 6

3.1 Unpacking and inspection ..................................................................................................................... 6

3.2 Notes ..................................................................................................................................................... 6

3.3 UPS input connection ............................................................................................................................ 6

3.4 UPS output connection ......................................................................................................................... 6

3.5 Long backup external battery connection ............................................................................................. 7

4.Panel display,operation and running ........................................................................................................ 8

4.1 Faceplate display illumination ............................................................................................................... 8

4.2 Operation ............................................................................................................................................. 10

4.3 Parameter setting ................................................................................................................................ 11

4.4 Parameters inquiring ........................................................................................................................... 17

4.5 Run mode ............................................................................................................................................ 18

5.Maintenance ............................................................................................................................................... 20

5.1 Battery Maintenance ........................................................................................................................... 20

6.Troubleshooting and performance of product....................................................................................... 20

6.1 LED indication and warning table ....................................................................................................... 21

6.2 Troubleshooting ................................................................................................................................... 22

6.3 EMC standard/Safety standard ........................................................................................................... 23

6.4 Product Performance .......................................................................................................................... 23

6.5 Communication interface .................................................................................................................... 25

Manual instruction
Thanks for purchasing our UPS, it is safe and reliable, so few maintenance is required.
Read this manual carefully and completely. It includes instructions of safety installation and operation. They will help your UPS obtain
the longest life and service. This manual accounts the internal working principle and the relative protection functions. This manual also
contains information about the usage of the equipment.
Please obey the instructions and all the warning stated in the manual or on the machine. Don’t operate the machine before fin ishing
reading the safety and operation instructions.

Note: Because of the continuous improvements, our products may differ somewhat from the contents included in this manual. You can
contact local office to get the information when necessary.

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 3

1. SAFETY INSTRUCTION

This chapter mainly introduce the safety marks and notes of MISSION 1KVA-2KVA-3KVA series on-line UPS.
Read this chapter carefully before operating on the equipment.

1.1 Safety instruction

There is dangerous voltage and high temperature inside the UPS. During the installation, operation and
maintenance, please abide the local safety instructions and relative laws, otherwise it will result in personnel
injury or equipment damage. Safety instructions in this manual act as a supplementary for the local safety
instructions.
Our company will not assume the liability that caused by disobey of safety instructions. Please note the
following:

1. Don’t use the UPS when the actual load exceeds the rated load.

2. There are high-capacity batteries in the standard type UPS. You mustn’t open the enclosure or it will lead to
electric shock. If it needs internal maintenance or battery replacement, please send it to the designated site.

3. Internal short-circuit of the UPS will cause electric shock or fire. So don’t place the containers equipped with
liquid on the top of the UPS so as not to cause danger of electric shock and so on.

4. Don’t put the UPS in a place with high temperature or humidity as well as the corrosive gas, much dust.

5. Keep good air circulation between in-vent on front panel and out-vent on back panel.

6. Avoid direct sunlight or near heat-dispensed objects.

7. In case that the smoke appears on the UPS, please cut off the power as soon as possible and contact the
dealer service site.

1.2 Symbols indication

The safety symbols cited in this manual are shown in table 1-1, which are used to inform readers of safety
issues that should be obeyed when installation, operation and maintenance.

Safety Symbol

Indication

Attention

Static discharge sensitive

Electric shock

Table 1-1

There are three levers of safety grade: Dangerous, Warning and Attention. The remark is on the right side of the
safety symbol, the detailed comments is behind, shown as following:

Dangerous: Indicate risk of serious injury or death or seriously damage the equipment

Warning: Indicate risk of serious injury or damage the equipment.

Attention: Indicate risk of injury or damage the equipment.

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 4

2. PRODUCT INTRODUCTION

2.1 The appearance of the product

Fig. 1 Front Panel view Fig. 2 1KVA Rear Panel view

Fig. 3 2KVA Rear Panel view Fig. 4 3KVA Rear Panel view

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 5

2.2 The principle of the product

Fig 5 UPS Principle Diagram

1. Input filter: Complete filtering the input AC utility power to provide the clean power for UPS.

2. AC/DC converter: Convert the filtered AC mains to DC and boost the DC for DC/AC inverter.

3. DC/DC booster: When the UPS works in battery mode, the circuit boosts the DC for DC/AC inverter.

4. DC/AC inverter: Convert the boosted DC to stable AC output.

5. Bypass: When overload or failure of inverting happen in the UPS, it transfers to bypass mode to supply power

to loads.

6. Charger: Standard unit provides 1A; long backup unit provides 7A.

7. Battery: Sealed Lead Acid Battery.

8. Output filter: Complete filtering the output of the UPS to provide the clean power for loads.

2.3 Model

UPS sort

MODEL NO

Remark

Standard unit

1KVA

Internal 1A charger, 2 PCS 7AH batteries

2KVA

Internal 1A charger, 4 PCS 7AH batteries

3KVA

Internal 1A charger, 6 PCS 7AH batteries

Long backup unit

1KVA

★internal 6A charger, external 24V battery

2KVA

★internal 6A charger, external 48V battery

3KVA

★internal 6A charger, external 72V battery

The 12V/9AH battery which is sealed lead acid maintenance free can be chosen as internal battery of the
standard unit.
The 7A charger can be chosen as internal charger of the long backup unit.
Two internal chargers can be used in long backup unit.

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 6

3. INSTALLATION

3.1 Unpacking and inspection

1. Unpacking the box and check the UPS. If damaged or some parts missing, don’t start the machine and

inform your supplier.

2. Check the box content (please consult Box Content Table).

3. Check if the UPS is that you wanted to purchase. You can verify it on the label on the rear panel of the

UPS.

3.2 Notes

1. Please place the UPS in a clean, stable environment, avoid the vibration, dust, too humidity, flammable gas

and liquid, corrosive.

2. The ambient temperature around UPS should keep in a range of 0°C～40°C. If UPS works above 40°C, it

is required that the rated value of the largest load decreases 12% while the temperature increases every
5°C . The highest temperature cannot be more than 50°C when UPS works.

3. UPS should be placed in a sufficiently ventilated place.

3.3 UPS input connection

Connect the UPS to the mains by input power cable which is equipped with the UPS.

Fig 6 Input Connection

3.4 UPS output connection

Fig 7 Output connection

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 7

3.5 Long backup external battery connection

Fig 8 Battery connection

Warning:

★ Before installing battery, make sure that UPS and breaker are all turned off. Remove all your metallic

adornment such as finger ring, watch, and so on before connecting battery.

★ No anti-connection or short circuit between the battery anode and cathode forever. Red cable connect with

battery anode “+” and black cable connect with cathode “-”.

★ Please use the screwdriver with insulating handle. Do not lay the tools or metallic goods on the battery.

Notice:

★ When using the external battery, It is best to use external battery cable which matches with the equipment.
★ When connecting load to UPS, first turn off load and then connect the power cable and finally turn on load

one-by-one.

★ Inductance loads such as motor, fluorescent lamp, photocopier are strictly prohibited connecting to UPS to

avoid damage.

★ Plug UPS on the special socket with over-current protection, the power socket that used should be

connected with ground wire.

★ UPS is likely to have output voltage no matter whether the power input cable is plugged in mains input

socket. If you wish UPS have no output, first break off the switch and then cancel the mains.

★ When connect laser printer, select the capacity of UPS according to the UPS start power because the startup

power is higher.

MISSION 1K●2K●3K

SINGLE PHASE

Rev. 02 – 19 March 2015 8

4. PANEL DISPLAY, OPERATION AND RUNNING

The operation is simple, operators only need to read the manual and follow the operation instructions listed in
this manual without any special training.

4.1 Faceplate display illumination

4.1.1 Keys function

Fig. 9 Front panel buttons instruction

ON key +
Press and hold this key for more than half a second to turn on the UPS.

OFF key +
Press and hold this key for more than half a second to turn off the UPS.

TEST/MUTE key +
Press and hold the key for more than 1 second in Line mode or economical mode: UPS runs the self-test
function.
Press and hold the key for more than 1 second in battery mode: UPS runs the mute function.

INQUIRING key or
Non-function setting mode:
Press and hold the key for more than half a second (less than 2 seconds): Indicate the items of the LCD item
section orderly.
Press and hold this key for more than 2 seconds: Circularly and orderly display the items every 2 seconds,
when press and hold the key for some time again, it will turn to output status.

Function setting mode:

Press and hold the key for more than half a second (less than 2 seconds): Select the set option.
FUNCTION SETTING key

Non-function setting mode:
Press and hold the key for more than 2 seconds: Function setting interface.
Function setting mode:
Press and hold the key for more than half a second (less than 2 seconds): Affirm the set option.
Press and hold the key for more than 2 seconds, exit from this function setting interface.