(OR(QWXLWLYH7RXFKPRQLWRU
8VHU*XLGH
/&'3DQHO0RXQW7RXFKPRQLWRU
(7/6:&
5HYLVLRQ&
31
(OR7RXFK6\VWHPV,QF
(/2728&+
ZZZHORWRXFKFRP
Table of Contents
Chapter 1
Introduction 1
Precautions . . . . . . . . . . . . . . . . . . . . 1
About the Product . . . . . . . . . . . . . . . . . 1
Chapter 2
Installation and Setup 3
Unpacking Your Panel Mount
Touchmonitor . . . . . . . . . . . . . . . . . . 4
Product Overview . . . . . . . . . . . . . . . . . 5
Main Unit . . . . . . . . . . . . . . . . . . . . 5
Rear View . . . . . . . . . . . . . . . . . . . 5
Bottom View . . . . . . . . . . . . . . . . . . 6
Remote OSD with Cable Attachment . . . . . 6
Mounting Your Touchmonitor . . . . . . . . . . . 7
Connecting Your Touchmonitor . . . . . . . . . . 8
Optimizing the LCD Display . . . . . . . . . . . 11
Installing the Driver Software . . . . . . . . . . 12
Installing the Serial Touch Driver for Windows
XP, Windows 2000, Me, 95/98 and NT 4.0 . 13
Installing the Serial Touch Driver for MS-DOS
and
Windows 3.1 . . . . . . . . . . . . . . . 14
Chapter 3
Operation 15
About Touchmonitor Adjustments . . . . . . . . 15
Connecting the OSD Module . . . . . . . . . . 16
OSD Module Controls . . . . . . . . . . . . . . 17
OSD Menu Function. . . . . . . . . . . . . . . 18
Compatibility Modes . . . . . . . . . . . . . . 25
Touchmonitor Specifications . . . . . . . . . . 26
15" LCD Touchmonitor (ET1566L) Specifications
26
AccuTouch Touchscreen Specifications . . . 27
15" LCD Panel Mount Touchmonitor (ET1566L-
7SWC-1) Dimensions . . . . . . . . . . . 28
Panel Cutout. . . . . . . . . . . . . . . . . 30
Regulatory Information 31
Warranty 35
Index 37
Chapter 4
Troubleshooting 19
Solutions to Common Problems. . . . . . . . . 19
Appendix A
Native Resolution 21
Appendix B
Touchmonitor Safety 23
Care and Handling of Your Touchmonitor . . . . 24
Appendix C
Technical Specifications 25
1
2
Copyright © 2003 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
3
Congratulations on your purchase of an Elo TouchSystems Entuitive LCD panel
mount touchmonitor. Your new high-resolution industrial touchmonitor
combines the reliable performance of Elo’s touch technology with the latest
advances in LCD display design. This combination of features creates a natural
flow of information between you and your touchmonitor.
Precautions
C HAPTER
C
HAPTER
1
I
NTRODUCTION
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
About the Product
Your LCD panel mount Touchmonitor is a 15" XGA TFT color display with the
following features:
• Direct analog RGB input
• 15.0” diagonal screen size
• 16.7 million displayable colors (262,144-1549L)
• 1024 x 768 resolution
• XGA/ SVGA/ VGA/ VESA/ Mac/ NEC PC-98 compatible
• 24~60kHz horizontal scan
• 56~75Hz refresh rate
1-1
• Auto adjustment capability
• High quality full screen re-scaling
• Multilingual OSD menus in four languages: English, French, Italian,
Spanish, and Japanese
• VESA flat panel monitor physical mounting interface (75mm)
• Worldwide agency approvals that include UL*, CUL*, TÜV- Bauart, FCC,
CE, C-Tick, VCCI
• Certified by UL to NEMA 4, 4x and 12: ET1566L-7SWC-1*
• Designed to meet NEMA 4, 4x & 12: ET1566L-9SWC-1/5*
*ITE recognized component
For full Product Specifications refer to Appendix C.
1-2 Elo Entuitive Touchmonitor User Guide
C HAPTER
C
HAPTER
2
I
NSTALLATION AND
This chapter discusses how to install your LCD panel mount touchmonitor and
how to install Elo TouchSystems driver software.
S
ETUP
2-3
Unpacking Your Panel Mount
Touchmonitor
Check that the following 7 items are present and in good condition:
6HULDOWRXFKVFUHHQ
FDEOH
9LGHRFDEOH
/&''LVSOD\
0RQLWRUSRZHUFDEOH86&DQDGD
CD
Software
Quick
Installation
Guide
4XLFN,QVWDOODWLRQ*XLGHDQG
VRIWZDUH&'
AUTO/SEL DOWN UP MENU
26'PRGXOH
(XURSHDQPRQLWRUSRZHUFDEOH
1RWHVKLSPHQWVWRWKH8.ZLOO
FRQWDLQD8.SRZHUFRUGDOVR
2-4 Elo Entuitive Touchmonitor User Guide
Product Overview
Main Unit
Rear View
LCD Display
2-5
Bottom View
Remote OSD with Cable Attachment
AUTO/SEL DOWN UP MENU
Customer Panel
2-6 Elo Entuitive Touchmonitor User Guide
Mounting Your Touchmonitor
N
OTE
:
You will need a 6mm allen socket and torque wrench (Hex) to attach the mounting
brackets.
Your panel mount touchmonitor comes with 6 mounting brackets (and 6
screws). You will need 6 brackets to mount your touchmonitor. Two brackets
attach to the top and bottom and one on each side.
To mount your touchmonitor to a panel, follow the steps below:
1 Prepare the opening in the panel (307mm x 398.2mm/12.08" x 15.68"). See
page C-36. Mounting panel thickness must not exceed 13mm.
2 Disassemble the 6 brackets and NEMA frame.
3 Verify that your touchmonitor will clear the opening as you attempt to front
mount it. The opening will be covered by the bezel flanges.
4 Mount the touchmonitor from the front side of the opening in the supporting
panel and temporarily secure it.
5 From the back of the panel opening, slip the NEMA frame over the rear
cover. Attach the 6 brackets into the slots. Use 2 brackets on top and bottom
and 1 on each side.
6 To secure the touchmonitor, turn the screws clockwise until a firm
contact is made with the NEMA frame. To assure a “flat” mount, screws
should be tightened “cris-cross” and not sequentially, i.e. tighten the
upper left corner screw first then the lower right screw. Torque screws
to 35 in lbs. (4 Nm).
2-7
Connecting Your Touchmonitor
The following illustrations guide you step by step in connecting your
touchmonitor.
Before connecting the cables to your touchmonitor and PC, be sure that the computer
and the touchmonitor are turned off.
Serial cable
US
power cable
Powe r
Power switch
Connections on underside
OSD module
connector
Female 15-pin
video
connector
Serial
touchscreen
connector
AUTO/SEL DOWN UP MENU
European
power cable
Video cable
OSD module
2-8 Elo Entuitive Touchmonitor User Guide
STEP 1-Connecting the Video Cable
Connections on underside
Female 15-pin
video
connector
Video
cable
Ferrite bead
Video
port
• Connect the 15-pin video cable (the ferrite bead end) to the video port on
your PC.
• Connect the other end of the video cable to the video connector on your
touchmonitor.
• Secure the cable to your touchmonitor and PC by turning the screws on the
connector clockwise.
2-9
STEP 2-Connecting the Serial Touchscreen Cable
Connections on underside
Serial
touchscreen
connector
Serial
touchscreen
cable
• Connect the female end of the serial (RS-232) cable to the serial port on the
back of your PC.
• Connect the male end of the cable to the serial touchscreen connector on your
touchmonitor.
• Secure the cable to your touchmonitor and PC by turning the screws on the
connector.
2-10 Elo Entuitive Touchmonitor User Guide
STEP 3-Connecting the Power Cable
Connections on underside
Powe r
Power switch
Powe r
cable
Depending on where you live, you will use either the European or US/Canadian
power cable.
• Connect the female end of the power cable to the Brick power supply.
• Connect the Brick power supply into the power port on the touchmonitor.
To protect your equipment against risk of damage from electrical surges in the power
line, plug the brick supply’s power cord into a surge protector, and then connect the surge
protector to a grounded (three-pronged) AC electrical outlet.
• Power on your PC then your touchmonitor. After a brief pause the picture
should appear.
• The power can be turned on and off by the small white switch on the back of
the touchmonitor. The touchmonitor can also be turned on and off by
plugging and unplugging the power cable.
Optimizing the LCD Display
To ensure the LCD display works well with your computer, configure the
display mode of your graphic card to output 1024 x 768 resolution, and make
sure the timing of the display mode is compatible with the LCD display. Refer
to Appendix A for more information about resolution. Compatible video modes
for your touchmonitor are listed in Appendix C. Refer to Chapter 3 for more
information on adjusting your touchmonitor’s video characteristics.
2-11
Installing the Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to
work with your computer. Drivers are located on the enclosed CD-ROM for the
following operating systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Additional drivers and driver information for other operating systems (including
MS DOS, Windows 3.x, OS/2, Macintosh and Linux) are available on the Elo
TouchSystems web site at www.elotouch.com.
Your Elo touchmonitor is plug-and-play™ compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when
Windows starts. If Windows detects your touchmonitor, follow the instructions
on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
2-12 Elo Entuitive Touchmonitor User Guide
Installing the Serial Touch Driver for Windows XP,
Windows 20001, Me, 95/98 and NT 4.0
N
OTE
:
For Windows 2000 and NT 4.0 you must have administrator access rights to install the
driver.
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
If the AutoStart feature for the CD-ROM drive is active, the system
automatically detects the CD and starts the setup program.
2 Follow the directions on the screen to complete the driver setup for your
version of Windows.
If the AutoStart feature is not active:
1 Click Start > Run.
2 Click the Browse button and locate the EloCd.exe program on the CD-ROM.
3 Click Open, then OK to run EloCd.exe.
4 Follow the on-screen directions to complete the driver setup for your version
of Windows.
1.To install Windows 2000 and Windows XP, you must use the "update driver"
method; you will not find a setup.exe file within the download.
2-13
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1
To install the drivers for Windows 3.x and MS-DOS from Windows 95/98,
follow these steps:
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
2 From DOS, type d:\EloDos_W31 to change to the correct directory on the
CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
3 Type INSTALL and press Enter to start the installation.
4 Align the touchscreen.
If you need additional installation information, see Chapter 2 of the
Elo DOS and Windows Driver Guide found on www.elotouch.com .
To run the INSTALL program:
1 Type INSTALL at the DOS prompt in the directory containing the driver
install files.
2 INSTALL asks you to select the software to install.
3 Choose d:\EloDos_W31 from the displayed list.
4 INSTALL also asks you for the paths to use during installation. You may
select a path, or use the defaults. INSTALL creates directories as necessary,
and warns you if they exist.
If you are updating your software, you may wish to specify the paths containing
the earlier versions, and overwrite the obsolete files. All executable programs
are upward compatible. For a list of differences from each previous version of
the drivers, be sure to select "Differences from Previous Versions" during the
installation process.
INSTALL updates your AUTOEXEC.BAT file with the drivers you select.
INSTALL makes a copy of your original AUTOEXEC.BAT file, called
AUTOEXEC.OLD. If you already have Elo driver commands in your
AUTOEXEC.BAT file, they will be commented out.
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory
you specified. GO loads the touchscreen driver, runs the calibration program
ELOCALIB, and gives you some final instructions.
If you are using Windows 3.1, you will also align the touchscreen within
Windows 3.1 using the Touchscreen Control Panel.
2-14 Elo Entuitive Touchmonitor User Guide
About Touchmonitor Adjustments
Variations in video output and application will likely require you to adjust your
touchmonitor to optimize the quality of the display.
For best performance, your monitor should be operating in native resolution;
that is, 1024 x 768 at 60-75 MHz. Use the Display control panel in Windows to
choose 1024 x 768 resolution.
C HAPTER
C
HAPTER
3
O
PERATION
Operating in other resolutions will degrade video performance. For further
information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This
feature saves you from having to reset your choices every time you unplug or
power your touchmonitor off and on. If there is a power failure your
touchmonitor settings will not default to the factory specifications.
3-15
Connecting the OSD Module
All adjustments are made by using the remote on-screen display (OSD) module.
First, connect the OSD module by inserting the corded end into the OSD
module connector in the back of the monitor.
OSD module
AUTO/SEL DOWN UP MENU
Connections on underside
Powe r
cable
Serial
touchscreen
connector
3-16 Elo Entuitive Touchmonitor User Guide
OSD Module Controls
1
MENU
UP
2
3
DOWN
4
AUTO/SEL
5
$8726(/'2:1830(18
243 1
5
Contro l Function
Menu
Contrast/
Plus/Clockwise
Brightness/Minus/
Counter-Clockwise
Auto/Select
Power Switch Switches on/off the power of your touchmonitor.
Enable/Disable
Display Exits the OSD menus.
1. Enter contrast of the OSD
2. Increase value of the adjustment item.
3. Select item clockwise
1. Enter brightness of the OSD
2. Decrease value of the adjustment item
3. Select item counter-clockwise
Select- To select the adjustment items from the
OSD menus.
Auto- To activate the “Auto Adjustment”
function to obtain an optimum image.
1. Press the Menu and Up buttons at the same
time and hold for two seconds to enable/disable
the OSD functions. OSD menu default is
enabled.
2. Press the Menu and Down buttons at the same
time to enable/disable the power lock function.
3-17
OSD Menu Function
CONTRAST
50
Contrast
Controls the picture contrast
Brightness
Controls the picture brightness
V-Position
Controls the vertical position
H-Position
Controls the horizontal position
Recall Defaults
Recalls factory settings of the image
parameters
C1/C2/USER (Color)
Using these icons, you can select one
of the preset color temperatures
(9300°K or 6500°K). Confirm your
choice by pressing the SELECT
button. If you want to change the color
temperatures individually, select
USER and confirm by pressing the
OSD button SELECT. Now you can
use the OSD dial to toggle between the
settings R, G and B (red, green and
blue foreground). To change a setting,
first press the SELECT button, then
choose the desired value with the OSD
dial. To confirm the setting, press the
SELECT button again.
If you don’t need to adjust any further
settings, choose the icon to return to
the OSD main menu.
Phase
Controls the vertical fine adjustment
Clock
Controls the horizontal fine adjustment
OSD H-Position
Adjusts the horizontal position of the OSD menu
OSD V-Position
Adjust the vertical position of the OSD menu
OSD Time
Determines how long (in seconds) the OSD
menu waits before closing automatically after no
action has been performed.
Auto Adjust
Automatically selects the optional settings for
image parameters (brightness, contrast, image
position, phase, etc.)
OSD Language
Selection of the OSD menu language: English,
French, Italian, Spanish, Japanese.
Image Information
Displays the current graphics mode.
3-18 Elo Entuitive Touchmonitor User Guide
If you are experiencing trouble with your touchmonitor, refer to the following
table. If the problem persists, please contact your reseller or our technical
support at 1-800-557-1458.
Solutions to Common Problems
Problem Suggestion(s)
No image appears on screen. Check that all the I/O and power connectors are
Partial image or incorrectly displayed
image.
Image has vertical flickering line bars. Use the Tracking function to make an adjustment.
properly connected as described in Chapter 2.
Make sure the pins of the connectors are not crooked
or broken.
Test power supply by trying different cables, or a
different wall outlet or plug another appliance into
the outlet.
Make certain the video cable is properly connected
and that it is not damaged. Check for bent pins on
the cable connectors.
Ensure that your computer and video card are
properly configured. (Consult video card
documentation.)
Check whether the resolution of your computer is
higher than that of the LCD display.
Reconfigure the resolution of your computer to
make it less than or equal to 1024 x 768. See
Appendix A for more information on resolution.
Check and reconfigure the display mode of the
vertical refresh rate of your graphic card to make it
compatible with the LCD display.
C HAPTER
C
HAPTER
4
T
ROUBLESHOOTING
4-19
Problem Suggestion(s)
Image is unstable and flickering Use the Tracking function to make an adjustment.
Image is scrolling Make sure the VGA signal cable (or adapter) is well
Touch doesn’t work Make sure the touchscreen cable is securely
Remote OSD does not work Press the UP and Down buttons simultaneously for a
connected.
Check and reconfigure the display mode of the
vertical refresh rate of your graphic card to make it
compatible with the LCD display.
connected at both ends.
few seconds to enable the function.
4-20 Elo Entuitive Touchmonitor User Guide
A PPENDIX
C
HAPTER
4
N
ATIVE
The native resolution of a monitor is the resolution at which the LCD panel is
designed to perform best. In almost all cases, screen images look best when
viewed at their native resolution. You can lower the resolution setting of a
monitor but not increase it. For the Elo LCD touchmonitor, XGA-15 inch, the
native resolution is 1024 x 768.
Input Video 15" LCD
640 x 480 (VGA) Transforms input format to 1024 x 768 size
800 x 600 (SVGA) Transforms input format to 1024 x 768 size
1024 x 768 (XGA) Displays in native resolution
R
ESOLUTION
The native resolution of an LCD is the resolution that matches the LCD’s
pixels. Video performance is always best at native resolution settings. The
various standard LCD resolutions are usually represented as follows:
VGA
SVGA
XGA
640 x 480
800 x 600
1024 x 768
A-21
For example, a SVGA resolution LCD panel displays 800 pixels horizontally
and 600 pixels vertically. Input video is also represented by the same terms.
XGA input video has a format of 1024 pixels horizontally by 768 pixels
vertically. When the input pixels contained in the video input format match the
native resolution of the panel, there is a one-to- one correspondence of mapping
of input video pixels to LCD pixels. For example, the pixel in 45 column and 26
row of the input video is in 45 column and 26 row of the LCD. When the input
video is set at a lower resolution than the native resolution of the LCD, the
direct correspondence between the video pixels and the LCD pixels is lost. The
LCD controller can compute the correspondence between video pixels and LCD
pixels using algorithms contained in the controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels.
Poor fidelity conversion can result in artifacts in the LCD display, such as
characters of varying width.
A-22 Elo Entuitive Touchmonitor User Guide
A PPENDIX
C
HAPTER
4
T
OUCHMONITOR
This manual contains information that is important for the proper setup and
maintenance of your industrial touchmonitor. Before setting up and powering
on your new touchmonitor, read through this manual, especially Chapter 2
(Installation), and Chapter 3 (Operation).
1 To reduce the risk of electric shock, follow all safety notices and never open
the touchmonitor or brick supply case.
2 Turn off the product before cleaning
S
AFETY
3 Your new brick supply is equipped with a 3-wire, grounding power cord. The
power cord plug will only fit into a three-prong safety ground outlet. Do not
attempt to fit the plug into an outlet that has not been configured for this
purpose. Do not use a damaged power cord. Use only the power cord that
comes with your Elo TouchSystems touchmonitor. Use of an unauthorized
power cord may invalidate your warranty.
4 The slots located on the sides and top of the brick supply and touchmonitor
case are for ventilation. Do not block or insert anything inside the ventilation
slots.
5 It is important that the brick supply and the rear portion of your touchmonitor
remain dry. Do not pour liquid into or onto your brick supply or
touchmonitor. If your brick supply or touchmonitor become wet do not
attempt to repair them yourself.
B-23
Care and Handling of Your Touchmonitor
The following tips will help keep your Elo Entuitive touchmonitor functioning
at the optimal level.
• To avoid risk of electric shock, do not disassemble the brick supply or
display unit cabinet. The unit is not user serviceable. Remember to unplug
the display unit from the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do
not use thinner or benzene, abrasive cleaners or compressed air.
• To clean the brick supply or display unit cabinet, use a cloth lightly
dampened with a mild detergent.
• Avoid getting liquids inside your brick supply or touchmonitor. If liquid does
get inside, have a qualified service technician check it before you power it on
again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the
rag and wipe the touchscreen. Never apply the cleaner directly on the
touchscreen.
B-24 Elo Entuitive Touchmonitor User Guide
Compatibility Modes
Your Elo Entuitive touchmonitor is compatible with the following standard
video modes. All specifications are typical and subject to change.
Mode Resolution H. Frequency (kHz) V. Frequency (Hz)
IBM & VESA VGA 640 x 350 31.47 70.09
IBM & VESA VGA 640 x 400 31.47 70.09
IBM & VESA VGA 720 x 400 31.47 70.09
IBM & VESA VGA 640 x 480 31.47 59.94
IBM & VESA VGA 640 x 480 37.86 72.81
IBM & VESA VGA 640 x 480 37.50 75.00
VESA VGA 800 x 600 35.16 56.25
VESA VGA 800 x 600 37.88 60.32
VESA VGA 800 x 600 48.08 72.19
VESA VGA 800 x 600 46.88 75.00
VESA VGA 800 x 600 48.36 60.00
VESA VGA 800 x 600 56.48 70.07
VESA VGA 800 x 600 60.02 75.03
Apple Macintosh LC 13" 640 x 480 34.97 66.61
Apple Macintosh II 13" 640 x 480 35.00 66.67
Apple Macintosh 16" 832 x 624 49.73 74.55
Apple Macintosh 19" 1024 x 768 60.24 75.02
NEC FC-98 series 640 x 400 24.83 56.42
NEC FC-98 series 640 x 400 31.47 70.01
NEC FC-98 series 640 x 480 31.47 59.94
C
HAPTER
4
T
ECHNICAL
A PPENDIX
S
PECIFICATIONS
C-25
Touchmonitor Specifications
15" LCD Touchmonitor (ET1566L) Specifications
Display Type
Size
Pixel Format
Touchscreen
Colors
Display Brightness
Back-light Lamp Life
Viewing Angle
Contrast Ratio
Display Response Time
Environmental
Mechanical
Materials
Electrical
Agencies
Active matrix, thin film
transistor (TFT), liquid crystal
display
15-inch diagonal
304 x 228 mm useful screen
area
1024 x 768
Five-wire resistive technology
16 million with dithering
AccuTouch: 255 cd/m² typical.
40,000 hours at full brightness
typical
Horizontal
Vertical
450:1 typical
13 ms(tr)/27 ms(tr)
Operating Temp
Storage Temp
Humidity
Weight
Size
Front bezel
Back cover
Input Video
Input Power
Power Dissipation
Safety & EMC
-75~75 or 150 degrees total
70~60 or 130 degrees total
0°C to 50°C
-30°C to +60°C
80% non-condensing
30 lbs. maximum approx. weight
See drawings on page 28.
5052H32 aluminum (3/16”) powder coat
cold roll steel zinc plated
VGA/SVGA/XGA analog video
100-240 VAC, 50/60 Hz.
Universal
UL*, cUL*, TÜV-Bauart,
FCC-B, CE-B, C-Tick, VCCI
Certified by UL to NEMA 4, 4x & 12 as a
Recognized Component (AT only).
* ITE Recognized Component
C-26 Elo Entuitive Touchmonitor User Guide
AccuTouch Touchscreen Specifications
Mechanical
Positional Accuracy Standard deviation of error is less than 0.080 in. (2.03 mm). Equates
Touchpoint Density More than 100,000 touchpoints/in
Touch Activation Force Typically less than 4 ounces (113 grams).
Surface Durability Surface durability is that of glass, Mohs’ hardness rating of 7.
Expected Life Performance AccuTouch technology has been operationally tested to more than 35
Sealing Unit is certified by UL to NEMA 4, 4x & 12 as a required
Optical
Visual Resolution All measurements made using USAF 1951 Resolution Chart, under
Gloss (per ASTM D2457
using a 60-degree gloss
meter)
Environmental
Chemical Resistance The active area of the touchscreen is resistant to all chemicals that do
Electrostatic Protection (per
EN 61 000-4-2)
to less than ±1%.
million touches in one location without failure, using a stylus similar
to a finger.
component.
30X magnification, with test unit located approximately 1.5 in (38
mm) from surface of resolution chart.
Antiglare surface: 6:1 minimum.
Antiglare surface: Curved: 60 ± 20 gloss units or 75 ± 15 gloss units.
not affect glass, such as:
Acetone
Methylene chloride
Methyl ethyl ketone
Isopropyl alcohol
Hexane
Turpentine
Mineral spirits
Unleaded Gasoline
Diesel Fuel
Motor Oil
Transmission Fluid
Antifreeze
Ammonia based glass cleaner
Vinegar
The touchscreen withstands 20 discharges of 15KV, distributed
randomly across the active area of the touchscreen with proper
transient protection.
2
(15,500 touchpoints/cm2).
C-27
15" LCD Panel Mount Touchmonitor (ET1566L-7SWC-1)
Dimensions
304
344
For cutout dimensions, see page 30.
228
435
Customer Panel
C-28 Elo Entuitive Touchmonitor User Guide
446
396
75
306
Customer Panel
12.7mm
355
75
64
59
N
OTE
:
Dimensions in millimeters (inches)
C-29
Panel Cutout
Maximum panel thickness 13mm (0.5")
+1
400 MIN
0
+1
310 MIN
0
.
C-30 Elo Entuitive Touchmonitor User Guide
C
HAPTER
4
R
EGULATORY INFORMATION
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein will likely result in improper operation,
damage to the equipment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service
should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral
safety ground wire and 3-prong connector intended for connection to a grounded
safety outlet.
1) Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire outlet as
this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for
radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided
cords and cabling may compromise electrical safety or CE Mark Certification for
emissions or immunity as required by the following standards:
This Information Technology Equipment (ITE) is required to have a CE Mark
on the manufacturer’s label which means that the equipment has been tested
to the following Directives and Standards:
31
This equipment has been tested to the requirements for the CE Mark as
required by EMC Directive 89/336/EEC indicated in European Standard EN
55 022 Class B and the Low Voltage Directive 73/23/EEC as indicated in
European Standard EN 60 950.
D) General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the
equipment may cause interference with radio and television communications.
There is, however, no guarantee that interference will not occur in any particular
installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must
observe the following:
a) Use only the provided I/O cables to connect this digital device with
any computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television
reception, or any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Unterminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician.
32 Elo Entuitive Touchmonitor User Guide
N10051
33
34 Elo Entuitive Touchmonitor User Guide
C
HAPTER
4
W
ARRANTY
Except as otherwise stated herein or in an order acknowledgment delivered to
Buyer, Seller warrants to Buyer that the Product shall be free of defects in
materials and workmanship. With the exception of negotiated warranty periods;
the warranty for the touchmonitor and components of the product is 3 years.
Seller makes no warranty regarding the model life of components. Seller’s
suppliers may at any time and from time to time make changes in the
components delivered as Products or components.
Buyer shall notify Seller in writing promptly (and in no case later than thirty
(30) days after discovery) of the failure of any Product to conform to the
warranty set forth above; shall describe in commercially reasonable detail in
such notice the symptoms associated with such failure; and shall provide to
Seller the opportunity to inspect such Products as installed, if possible. The
notice must be received by Seller during the Warranty Period for such product,
unless otherwise directed in writing by the Seller. Within thirty (30) days after
submitting such notice, Buyer shall package the allegedly defective Product in
its original shipping carton(s) or a functional equivalent and shall ship to Seller
at Buyer’s expense and risk.
Within a reasonable time after receipt of the allegedly defective Product and
verification by Seller that the Product fails to meet the warranty set forth above,
Seller shall correct such failure by, at Seller’s options, either (i) modifying or
repairing the Product or (ii) replacing the Product. Such modification, repair, or
replacement and the return shipment of the Product with minimum insurance to
Buyer shall be at Seller’s expense. Buyer shall bear the risk of loss or damage in
transit, and may insure the Product. Buyer shall reimburse Seller for
transportation cost incurred for Product returned but not found by Seller to be
defective. Modification or repair, of Products may, at Seller’s option, take place
either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify,
repair, or replace a Product to conform to the warranty set forth above, then
Seller shall, at Seller’s option, either refund to Buyer or credit to Buyer’s
account the purchase price of the Product less depreciation calculated on a
straight-line basis over Seller’s stated Warranty Period.
35
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES
FOR BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS
WARRANTY SET FORTH ABOVE, SELLER GRANTS NO OTHER
WARRANTIES, EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE,
REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE,
THEIR QUALITY, THEIR MERCHANTABILITY, THEIR
NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER
OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY
FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH
HEREIN. SELLER’S LIABILITY UNDER THE WARRANTY SHALL BE
LIMITED TO A REFUND OF THE PURCHASE PRICE OF THE PRODUCT.
IN NO EVENT SHALL SELLER BE LIABLE FOR THE COST OF
PROCUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY
BUYER OR FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR
INCIDENTAL DAMAGES.
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller
harmless from all liability relating to (i) assessing the suitability for Buyer’s
intended use of the Products and of any system design or drawing and (ii)
determining the compliance of Buyer’s use of the Products with applicable
laws, regulations, codes, and standards. Buyer retains and accepts full
responsibility for all warranty and other claims relating to or arising from
Buyer’s products, which include or incorporate Products or components
manufactured or supplied by Seller. Buyer is solely responsible for any and all
representations and warranties regarding the Products made or authorized by
Buyer. Buyer will indemnify Seller and hold Seller harmless from any liability,
claims, loss, cost, or expenses (including reasonable attorney’s fees) attributable
to Buyer’s products or representations or warranties concerning same.
36 Elo Entuitive Touchmonitor User Guide
Index
Numerics
15” LCD Panel Mount Touchmonitor (ET1566L-7SWC-1)
Dimensions, 28
15” LCD Touchmonitor (ET1566) Specifications, 26
A
About the Product, 1
About Touchmonitor Adjustments, 15
AccuTouch Touchmonitor Specifications, 27
Auto Adjust, 18
B
Bottom View, 6
Brightness, 18
C
C1/C2/USER (Color), 18
Care and Handling of Your Touchmonitor, 24
Clock, 18
Compatibility Modes, 25
Connecting the OSD Module, 16
Connecting the Power Cable, 11
Connecting the Serial Touchscreen Cable, 10
Connecting the Video Cable, 9
Connecting Your Touchmonitor, 8
Contrast, 18
E
Electrical Safety Information, 31
Emissions and Immunity Information, 31
H
H-Position, 18
I
Image Information, 18
Installation and Setup, 3
Installing the Driver Software, 12
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1, 14
Installing the Serial Touch Driver for Windows XP,
Windows 2000, Me, 95/98 and NT 4.0, 13
Introduction, 1
M
Main Unit, 5
Mounting Your Touchmonitor, 7
N
Native Resolution, 21
O
Operation, 15
Optimizing the LCD Display, 11
OSD H-Position, 18
OSD Language, 18
OSD Menu Function, 18
OSD Module Controls, 17
OSD Time, 18
OSD V-Position, 18
P
Panel Cutout, 30
Phase, 18
Precautions, 1
Product Overview, 5
R
Rear View, 5
Recall Defaults, 18
Regulatory Information, 31
Remote OSD with Cable Attachment, 6
S
Solutions to Common Problems, 19
T
Technical Specifications, 25
Touchmonitor Safety, 23
Touchmonitor Specifications, 26
Troubleshooting, 19
U
Unpacking Your Panel Mount Touchmonitor, 4
V
V-Position, 18
Index-37
W
Warranty, 35
Windows 3.1, 14
Index-38
Loading...