Elo Touch Solutions Elo 3202, Elo 4202, Elo 4602 Installation Manual

www.elotouch.com

Installation Guide

Wall Mount Kit for

Elo 3202/4202/4602 IDS Monitors

Revision A

P/N UM600076

© 2016 Elo Touch Solutions, Inc. All rights reserved.

Elo Touch Solutions Technical Support

Online self-help: www.elotouch.com/go/websupport

Technical Support contacts in your region:

www.elotouch.com/go/contactsupport

The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Afliates (collectively
“Elo”) makes no representations or warranties with respect to the contents herein, and specically disclaims any implied
warranties of merchantability or tness for a particular purpose. Elo reserves the right to revise this publication and to
make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or

changes.

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic,

optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.

Elo (logo) and Elo Touch Solutions are trademarks of Elo and its Afliates.

North America

Elo Touch Solutions
1033 McCarthy Boulevard
Milpitas, CA 95035

800-ELO-TOUCH
Tel [phone]
Fax [phone]
[e-mail]

Europe

Tel [phone]
Fax [phone]

[e-mail]

Asia-Pacic

Tel [phone]
Fax [phone]

www.elotouch.com.cn

Latin America

Tel [phone]
Fax [phone]
www.elotouch.com

Safety Warning:

Do not install this equipment on any wall or structure that is not capable of supporting four times
the weight of the IDS Display, brackets, and any accessories attached to it.

The 3202L monitor weighs in excess of 37lbs (17kg) with the optional Elo computer module.
37lbs x 4 = 148lbs (68kg).

The 4202L monitor weighs in excess of 55lbs (25kg) with the optional Elo computer module.
55lbs x 4 = 220lbs (100kg).

The 4602L monitor weighs in excess of 60lbs (27kg) with the optional Elo computer module.
60lbs x 4 = 240lbs (108kg).

Do not leave out any required parts or leave the monitor on the wall unattended without securely
fastening all brackets and screws as instructed in this document. Failure to follow all installation
instructions can result in an unsafe installation. Serious injury can occur if the IDS Display unex­pectedly falls due to improper installation.

Caution: This wall mount is intended for use only with the maximum weights indicated. Use with
heavier than the maximum weights indicated may allow the IDS Display to fall and cause injury.

Kit Contents

(Landscape and portrait installation templates, dimensional drawings, and the below hardware)

Upper Wall Bracket, (x1)

Lower Wall Bracket, (x1)

ECM Spacer, (x4)

M6X34 Phillips head screw (x8)

For IDS with ECM

M6X8 Phillips head screw (x8)

For IDS without ECM

1/4” x 2-1/2” at head wood screw (x6)

1/4” x 1-/2” hex head wood screw (x6)

1/4” Heavy Duty Toggle Anchor (x6)

(Additional anchors available P/N Toggler 25014)

1/4-20 x 2-1/2” at head machine screw (x4)

1/4-20 x 2-1/2” hex head machine screw (x2)

5/16” x 2-1/2” Concrete Sleeve Anchor (x6)

Minimum pullout strength rating = 1500lbs

M4X10 Phillips head screw (x2)

Lower Display Bracket, (x2)

Upper Display Bracket, (x1)

Step 1:

Remove the four (4) VESA mount covers to expose the wall mount bracket mounting pads. These
covers are not reused with this wall mount kit.

Step 2:

For mounting an IDS in landscape orientation, go to step 3a.

For mounting an IDS in portrait orientation, go to step 3b.

For mounting an IDS with ECM in landscape orientation, install the ECM kit following instructions
provided with it and go to step 3c.

For mounting an IDS with ECM in portrait orientation, install the ECM kit following instructions pro­vided with it and go to step 3d.