Elo Touch 17A2 Quick Installation Guide for Wireless Card

17A2

●

Note: Always handle the component by its edges.

●

Installer must be electrically grounded while performing installation steps.

DVD/ CD

Installing the Wireless card for the 17A2/15A2

Note: This wireless card is intended to be used only with a 17A2 or
15A2 touchcomputer. Elo Touchsystems is not liable for any damages
incurred while using this device in any non-specified manner.

Revision B
P/N E247787

North America

Elo TouchSystems

2008 Tyco Electronics.

301 Constitution Drive,
Menlo Park, CA 94025
www.elotouch.com

For current Elo news, product updates and announcements, register to receive our TouchMonitor newsletter
at www.elotouch.com/go/news

Elo Technical Support

Online self-help

:

www.elotouch.com/go/websupport

Technical Support contacts in your region:

www.elotouch.com/go/contactsupport

Europe

Tel [phone]
Fax [phone]
[e-mail]

Asia-Pacific

Tel [phone]
Fax [phone]
www.tps.co.jp

Latin America

Tel [phone]
Fax [phone]
www.elotouch.com.ar

1

Turn off power to the touchcomputer
and unplug the power adapter from
the unit.

15A2

1

Turn off power to the touchcomputer
and unplug the power adapter from
the unit.

2

Carefully place the touchcomputer
facedown on a soft, flat surface.
Turn touchcomputer upside down
and take off the back cover insert.

2

Carefully place the touchcomputer
facedown on a soft, flat surface.
Turn touchcomputer upside down
and take off the back cover insert.

3

If there is an installed DVD drive,
remove the two screws attaching
the DVD drive flap and remove
the flap. Then pull on the DVD
drive so it slides out of the
touchcomputer.

3

Unscrew the shielding that is
connected by six screws and
remove it.

4

Unscrew the shielding that is
connected by four screws and
remove it.

(B )

(A )

4

Remove the existing hard drive. Replace the hard drive into the hard

5

Unscrew the security screw and
remove the MiniPCI cover.

5

Align the pins of the Wireless card
with the connector at an angle and
push it in until the pins are in place.
Then push the Wireless card down
until it clicks. If the two side locks
on the connector do not click into
place, remove the card and repeat
the installation until the card clicks
securely in place.

6

Align the pins of the Wireless card
with the connector at an angle and
push it in until the pins are in place.
Then push the Wireless card down
until it clicks. If the two side locks
on the connector do not click into
place, remove the card and repeat
the installation until the card clicks
securely in place.

6

Take the cable labeled “Wireless
card” and connect it to the connector
labeled “MAIN” on the Wireless card.

7

Take the cable labeled “Wireless
card” and connect it to the connector
labeled “MAIN” on the Wireless card.

(B )

(A )

7

drive space. Push the hard drive
up until it snap locks into the
connector.

8

Reinstall the MiniPCI cover with the
security screw and reinstall the
shielding with the four screws.

If the DVD drive flap was previously
removed, reinstall the flap with the
two screws and reinsert the DVD
drive, verifying that the drive locks
securely in place.

8

Reinstall the shielding with the six
screws.

9 10

Replace the back cover insert.

9

Replace the back cover insert.

11

Reconnect the power adapter and
power on the touchcomputer.
Insert the software CD into the
DVD drive (or USB DVD drive) and
follow the on-screen instructions to
complete the Wireless Card software
installation.

DVD/ CD

10

Reconnect the power adapter and
power on the touchcomputer.
Insert the software CD into the
DVD drive (or USB DVD drive) and
follow the on-screen instructions to
complete the Wireless Card software
installation.

821107901201