No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission
of T yco Electronics.
Disclaimer
The information in this document is subject to change without notice. Tyco Electronics Corporation and
its Afffiliates in the TE Touch Solutions business unit in the TE Connectivity Ltd. family of companies
(collectively "TE") makes no representations or warranties with respect to the contents herein, and
specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. TE
reserves the right to revise this publication and to make changes from time to time in the content
hereof without obligation of TE to notify any person of such revisions or changes.
T rademark Acknowledgments
Elo TouchSystems, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks of the TE
Connectivity Ltd. family of companies. Windows is a trademark of the Microsoft group of companies.
DisplayLink is a registered trademark of DisplayLink (UK) Limited. Other product names mentioned
herein may be trademarks or registered trademarks of their respective companies. Tyco Electronics
claims no interest in trademarks other than its own.
Your new touchmonitor combines the reliable performance of Elo T ouchSystems touch products
with the latest developments in touch technology and display design. This combination of
features creates a natural flow of information between a user and the touchmonitor.
This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to
provide high quality display performance. Its LED backlight significantly reduces power
consumption and eliminates mercury (compared to CCFL-backlit panels). Other features that
enhance this LCD monitor’s performance are power/video/touch over one USB cable, an
optional magnetic strip reader (MSR), and an optional webcam.
Because of the special USB driver required, the touchmonitor cannot function as primary
display during boot-up. An additional display must be used to install the USB driver.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit and prevent risks to user safety. See the Safety & Maintenance
chapter for more information.
This manual contains information that is important for the proper setup and maintenance of the
unit. Before setting up and powering on your new touchmonitor, read through this manual,
especially the Installation, Mounting, and Operation chapters.
Chapter 1 - Introduction
User Manual – 0700L
SW601504 Rev B - Page 4 of 20
Chapter 2 –Installation
Unpacking the Touchmonitor
Open the carton and verify that the following items are present:
Touchmonitor with protective sheet for its face
Elo TouchTools CD & User Manuals CD
Quick Install Guide
USB Y-cable (“Data Cable”: Power and USB signal, “Aux Power Cable”: additional Power)
4 M4x8mm screws
Minimum Computer Hardware Requirements
2.0GHz Dual Core CPU
512MB of RAM. More if other applications are to run at the same time.
Windows 7, XP 32-bit (SP2, SP3), Vista 32-bit (SP1), or Vista 64-bit (SP1) operating
systems
2 USB 2.0 port
30MB of free disk space
CD-ROM drive or network access for software downloads
Primary display
Connector Panel & Interfaces
.
Mini-USB
User Manual – 0700L
SW601504 Rev B - Page 5 of 20
Touchmonitor Connections
1. Connect the mini-B plug of the provided USB Y cable to the mini-USB port on the monitor,
and connect the “Data Cable” connector of the provided USB Y cable into one of your
computer’s USB ports.
NOTE: Some computers may not provide enough power to the monitor
from one USB port. If so, connect the “Aux Power Cable” USB connector
on the Y end of the cable into another USB port on your computer.
2. The touchmonitor ships in an ON state: video should be displayed on your monitor once the
DisplayLink™ driver is installed on your computer.
Installing the DisplayLink Software Drivers
The DisplayLink technology enables video-over-USB. It allows your monitor to use one USB
cable for power, video and touch.
NOTE: This monitor can not function as Primary display during boot-up. An
additional display must be used to install the DisplayLink driver.
The drivers for the Windows 7, XP 32-bit (SP2, SP3), Vista 32-bit (SP1), and Vista 64-bit (SP1)
operating systems are provided with your touchmonitor on a CD.
Look in the USB Monitor folder in the Elo TouchTools CD for detailed driver manual.
User Manual – 0700L
SW601504 Rev B - Page 6 of 20
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.