How it Works
Elnur
Loading...
RF4E-PLUS
Installation Instructions
12 pgs815.69 Kb0

Elnur RF8E-PLUS, RF6E-PLUS, RF4E-PLUS, RF12E-PLUS, RF14E-PLUS Installation Instructions

...
Download
INSTALLATION INSTRUCTIONS AND USER GUIDE
RF
THERMAL RADIATORS
RF3P RF4P RF5P RF6P
RF8P RF10P RF12P RF14P
Please read these instructions CAREFULLY before installing or using this appliance for the first time.
RF3F RF4F RF5F RF6F
RF8F RF10F RF12F RF14F
INSTALLATION INSTRUCTIONS
1.- WARNING Please read these instructions before installing or using this appliance for the first time.
• The warranty of the heater will not instruction
s.
• The instructions should be retained for future reference. This guide must be kept and owner. This appliance can be used by children aged from 8 years and above and persons with reduced
•
sensory or mental capabilitie instruction
concerning the use of the appliance in a safe way and underst
s or lack of experience and knowledge if they have bee
Children must not play with the appliance. Cleaning and user without supervision.
•
Children aged from 3 years and less than 8 years shall only switch on/off the applianc has been placed or inst supervision involved. Ch
or instruction concerning use of the appliance in a safe way and underst
ildren aged from 3 years and less than 8 years shall not plug in, regulate and clean the
alled in its intended normal operating position a
appliance or perform user maintenance.
•
Children of less than 3 years should be kept away unless continuously supervised. Please check voltage in the rating labe Please check that the voltage in the rating label fi
•
The use of these heaters is forbidden in any area where there is a presence of gases
•
l fits the pow
inflammable objects.
•
Do not use this heater to dry clothes. Do not cover this heater or put objects in contact with it.
• Neither the connecting cable nor any other object must come into contact with the hot unit.
• Do not cover this heater at any time.
• The air outlet at the top of the thermal radiator and the air inlet at the bottom are provided to ensure
most efficie essential th
nt operation of the appliance. They also protect the heater from overheati at at no time are they covered.
• This heater should be switched off at the isolating switch before any repair work is carried out.
• The installation must be carried out in accordance with the current electrical regulatio
•
Should the heater be moved and reinstalled it is essential that the work is carried out technician
.
• The heater should not be installed just below an electrical socket.
• The appliance must be installed in such a way that it is impossible for anyone using a bath or sh
touch the co
ntrols.
• The heater is fitted with a flexible cable size 3 x 1.00 mm² for electrical connection. It may be used connect the
heater to the fixed wiring of the premised through a suitable connection
adjacent to the heater.
•
The supply circuit to the heater must incorporate a double pole isolating separation o
f at least 3 mm.
• If the flexible power cable for this unit is damage recognised
• This applianc All models are supplied with an electrical interrupt cut-out. This will switch off the heater
•
it overheats. Should the The cut-out The presence of air particles of smoke, dust and other pollutants could, in
•
surfaces aro CAUTION — Some parts of this product can become very hot and cause burns. Particular atte
•
by the manufacturer, as special tools are necessary.
e must be earthed.
cut-out operate, turn the heater off and remove the cause for
will be reset automatically
und the heat
er.
be given when children and vulnerable people are present.
cover any damage caused by non observance of any of these
given to any new
physical,
n given supervision or
and the hazards involved.
maintenance must not be made by ch
e provided that it
nd they have been given
and the hazards
that the
er supply.
ts the power supply.
, explosives or
ng; therefore, it is
ns.
by a fully qualified
ower, to
box positioned
switch having a contact
d, it may only be replaced by a repair workshop
if, for any reason,
the overheating.
.
time, discolour the walls and
ntion must
ildren
the
to
EN: WARNING: In order to avoid overheating do not cover the heater.
9
f
MODELS
MODULES W (cm) D (cm) H (cm)
WEIGHT (kg)
VOLTAGE INPUT (W)
RF3P RF3F RF3E
3 4 5 6 8 10 12 14
33.5 41.5 49.5 57.5 73.5 89.5 105.5 121.5
7,5 9,5 11,5 13 17 20 23,5 27
375 500 625 750 1000 1250 1500 2000
RF4P RF4F RF4E
RF5P RF5F RF5E
10 plus 2 cm separated from the wall
RF6P RF6F RF6E
220-240V~
RF8P RF8F RF8E
58
RF10P RF10F RF10E
RF12P RF12F RF12E
RF14P RF14F RF14E
2.- INSTRUCTIONS ON INSTALLATION
- Open the carton at the indicated side. The screws are in the accessories bag. Turn the carton upside down to allow the heater to stand. Check that it is the correct model and that it is in good condition.
- To obtain optimum performances it is necessary to maintain a minimum clearance of 15 cm between the radiator and any inflammable material as furniture, curtains etc. See figure.
shel
minimum 15cm
Closest
object to the
left end
minimum15cm
Position and fix the brackets at the correct distance from the floor and hang the unit on the hooks of the brackets. and mark the wall. Use the polystyrene packaging to level the heater and protect the floor.
- The studs and screws are in the accessories bag.
- Hung the unit on the hooks of the brackets.
- By turning the screw the metallic square will go downwards, retaining the heater. Repeat this on the other bracket.
minimum 25cm minimum 10cm
Use the heater as a template and mark the fixing points on the wall using a pencil through the two fixing holes in the square brackets.
Closest object to the right end
10
3.- USING THE THERMAL RADIATOR
r
SUN mode indicator
MOON mode indicato
Heating indicator
Operation in electronic models is controlled by means of two rotary knobs.
It is possible to regulate the temperature level with accuracy by means of the temperature selector. The heating indicator will be lit when the heater is consuming energy. When this dial is set in * position the heater is in frost protection mode, at this stage if the room temperature drops below 3ºC the heater will connect itself automatically.
There are three selectable positions with the mode selector dial:
Mode 0 : The heater is switched off permanently. No frost protection mode here.
MODELS RX-P
ELECTRONIC CONTROL
Temperature selector
Mode selector
Mode
Mode
: SUN mode on, the heater maintains the set temperature with the temperature selector dial.
: Moon mode on, the heater maintains a temperature 3ºC lower than the one set with the temperature selector dial.
11
MODELS RF
DIGITAL CONTROL
-F
Key +:
It increases the temperatu
Key -:
It decreases the temperatu
ECO key:
Press this key to activate the ECO mode.
re set point.
re set point.
Digital display:
It shows the temperature and other messages.
Heating indicator:
This small dot will be lit when the heater is consuming energy.
Start / Stop key:
Press this key to start / stop the heater. By pressing this key for a few seconds the keyboard will be locked. To unlock it press again this key for a few seconds.
START / STOP
Press the key small dot in the display will advise that the heater is in stand-by. To switch it off completely unplug the cable from the supply circuit or operate the double pole switch at the consumer unit.
SELECTING THE ROOM TEMPERATURE
The digital models RFS-F have a built-in ambient thermostat with a sensibility of 0.1ºC. It is possible to set the room temperature with an accuracy of 0.5ºC.
Set the room temperature by means of the display will show the existing room temperature. An small dot will be lit when the heater is consuming energy.
ECO MODE:
Select the ECO mode by pressing the
Note: It is possible to modify the set back value from the factory default value. Increase or decrease the value using the + and – keys. The new set back value for ECO mode will be stored
matically in a few seconds.
auto
FROST PROTECTION MODE :
With this mode on, if the room temperature drops below 5ºC the heater will connect itself automatically. Press the
KEYBO
– key to decrease the room temperature set point until the display shows H H H .
ARD LOCK
to start / stop the heater. Once the heater is started the display will show the room temperature. When the heater is stopped a
+ and – keys. The set point will be shown blinking, then it will be automatically validated and the
key. The display will show E c o and the room temperature will be reduced 3ºC.
3ºC to a different one. Press the
key four seconds and the display will show 3. 0 as
Press the
working internally. To unlock the keyboard press again the
key more than six seconds and the keyboard will be locked. The display will show and the controller will keep on
key more than four seconds.
12
It increases the
Key + :
values.
ITAL CONTROL WITH DAILY AND WEEKLY PROGRAMMING
DIG
DIGITALS MODELS RFE
Digital DISPLAY:
It shows the time, temperature and other messages.
Heating indicator:
This small dot will be lit when the heater is consuming energy.
SUN indicator
SUN key :
Press once to see the SUN temperature value. Press + or – keys to modify the value.
MOON key :
Press once to see the MOON temperature value. Press + or – keys to modify the value.
MOON indicator
Key - :
It decreases the values.
Frost protection key:
If the display shows the time the heater is in frost protection mode. Press this key to shift from frost protection mode to standard mode and vice versa.
Press this key for more than two seconds to set the time or day of the week.
PRG key:
Allows you to create check or modify programs. Move forward with + or – keys and allocate the SUN, MOON, or temperature to any of the 48 intervals of 30 minutes of the day by means of the relevant key.
Selector:
0 The heater is switched off
permanently.
P The heater is following a
program.
I The heater is maintaining
the SUN temperature constantly. Both indicators will be lit at the same time.
Digital models have built in an electronic thermostat with a sensibility of 0.1 ºC . It is possible to set temperatures with an accuracy of 0.5ºC.
The daily or weekly programmer (selectable) allows you to allocate three different temperature levels to any of the 48 intervals of 30 minutes of the day.
SWITCHING ON THE HEATER AND SETTING THE TIME
Turn the mode selector dial to P position and press the minutes by pressing is necessary to set the time press the
FROST PROTECTION MODE
With this mode on, if the room te If the display shows the time the heater is in frost protection mode. Press the
) to standard mode (temperature is shown in the display) and vice versa.
display
SELECTOR “O” , “P”, “I”.
Position “0” : The heater is switched off permanently. The display is switched off.
Position “P” : The heater is following a program. It will maintain the SUN, MOON or
Position “I” : The heater is maintaining the SUN temperature constantly both luminous indicators SUN and MOON will be lit. This could be useful
+ and - keys and press the . Set the hours the same way. Press once more the key to store the time. If at any time it
key and repeat the above steps.
:
mperature drops below 3ºC the heater will connect itself automatically.
position if the display shows the time the heater is frost protection mode.
when SUN temperature is required and we do not want to modify the program. At this position if the display shows the time the heater is in frost protection mode.
mode (temperature is shown in the display) and vice versa.
Press the key to shift from frost protection mode (time is shown in the display) to standard
key more than two seconds. The display will show the time intermittently. Set the
key to shift from frost protection mode (time is shown in the
temperatures as per the introduced program. At this
SUN, MOON AND
The electronic programmer is able to handle three temperature levels during the 24h of the day.
Press the
TEMPERATURES
key to set the SUN temperature. The display will show the SUN temperature value blinking.
13
Set the SUN temperature value by means of the + o – keys and press the key to store the value. If the display shows the time the heater is in frost protection mode. Press the
in the display) and vice versa.
key to shift from frost protection mode (time is shown in the display) to standard mode (temperature is shown
Repeat the above steps with the key The
temperature level is 3ºC and it is a fix value. This temperature level can be used as off selection when setting the temperatures during
curtain times of the day. SUN, MOON, or
DAILY PROGRAMMES
It is basic to visualize the day split into 48 intervals of 30 minutes each; SUN, MOON, or The default settings include daily mode so that the heater will repeat the program every day. If different programmes are required along a week, please see the next step WEEKLY PROGRAMMES. To check a programme or to make a new one follow these steps:
Press the OFF (frost protection) from 00:00h to 00:30h. If SUN or MOON temperatures are selected the relevant luminous indicator will be lit. If OFF
temperature
Press the to allocate SUN, MOON or OFF (frost protection) from 00:30h to 01:00h or press + key directly if the existing temperature level is ok. Repeat these steps allocating the desired temperatures levels over the 24 hours of the day. Press the
period. By reaching the At any time PRG key can be use also to store the program and return the previous mode.
SUN
MOON
OFF
Let’s see an example of how to introduce a program with the above distribution of temperatures.
OFF from 24:00h to 7:30h in the morning. The heater will be on only if the temperature drops to 3ºC.
SUN temperature from 7:30h to 9:00h.
MOON temperature from 9:00h to 13:00h.
SUN temperature from 13:00h to 15:00h.
MOON temperature from 15:00h to 19:30h.
SUN temperature from 19:30h to 24:00h.
temperatures can be allocated to any of the 48 intervals of 30 minutes of the day.
PRG key and the display will show 00:00 intermittently. Press one of the three keys to allocate SUN, MOON or
is selected both luminous indicators will be off.
+ key to go to the next interval. The display will show 00:30 intermittently and, again, press one of the three keys
23:30 in the display and pressing + key the controller will store the program and will return to the previous mode.
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 24:00
EXAMPLE
to set the MOON temperature.
1 - Press 2 - Press Off
3 - Press 4 - Repeat steps 2 and 3 until display shows: 07:30
5 - Press On 6 - Press
7 - Press 8 - Press
9 - Press 10 - Press
PRG 00:00
+ key 00:30
+ key 08:00
+ key 08:30
+ key 09:00
temperatures can be allocated to any of them.
– key at any time to modify a previous
11 - Press 12 - Press
13 - Repeat steps 11 and 12 until display shows: 13:00
14 - Press 15 - Press
16 - Repeat steps 14 and 15 until display shows: 15:00
17 - Press 18 - Press
19 - Repeat steps 17 and 18 until display shows: 19:30
20 - Press 21 - Press
22 - Repeat steps 20 and 21 until display shows:: 23:30
23 - Press 24 - Press
+ key 09:30
+ key 13:30
+ key 15:30
+ key 20:00
+ key GRAB
14
WEEKLY PROGRAMMES
It is possible to default) to 24hr/7days mode as follows:
Move the selector to key
at least five seconds. The display will show
SETTING by pressing
To check a programme or to make a new one press show 00:00 intermittently. Follow now the steps from DAILY PROGRAMMES section until the display shows again dia1 . Repeat this process with the 7 days of the week. When the display shows dia7 the weekly program will be stored by pressing + key.
If th
e display shows
It is pos until an audible signal is heard.
To turn back a controller from 24hr/7days to a single 24hr press
KEYBO
Press the
working internally. To unlock the keyboard press again the
allocate different programs to different days of the week. To do this, the controller has to be upgrade from 24hr mode (factory
0 position, the display will be Off. Press the key and at the same time turn the selector to P position maintaining the
P-SE which means that weekly mode has been set.
THE DAY: Press the
key more than two seconds and the display will show the number of the day. Set the correct number, if required,
+ or – keys. Press the key and the display will show now the time. Press again the key and new values will be stored.
PRG key: The display will show dia1 . Press again PRG key and the display will
dia1 then, pressing + key more than three seconds will copy the day 1 program to day 2 and so on.
sible to allocate any of the three temperature levels to all the intervals of any day maintaining the relevant
key
PRG key more than six seconds. This will restore the factory default settings.
ARD LOCK
key more than six seconds and the keyboard will be locked. The display will show and the controller will keep on
key more than six seconds .
4.- CLEANING AND MAINTENANCE
Clean and dust with a dry, soft cloth only when the unit is disconnected and cold.
Do not use solvents or abrasive products for cleaning.
This thermal radiator has been manufactured under an assured quality system using environment friendly
Please take the heaters to a clea
n point once their useful life is finished, in order to recycle their materials in the right way.
processes.
5.- TROUBLESHOOTING
thermal radiator does not heat. Check the heater or the air inlets ar
- The
Digital models: t or NI
GHT temperatures are right.
room does not reach the right
- The perat
tem
- D
are lit at the same time. Digital models: Continuous mode has been selected. Turn the knob to the “P” position to return to the
- The
- O
ure. Check the select
more heating power.
AY and NIGHT luminous indicators
Program mode if required.
display shows “Err1” or “Err2” Digital models: Contact the after sale service.
nly daily programmes. The controller is in a single 24hr mode (factory default). See WEEKLY PROGRAMMES section to swift to
24hr/7days mode.
he display shows the time press the
ed temperature is in accordance with the desired temperature. Maybe the room needs
e not covered.
key to switch on the heater. Check that the DAY
keyboard is locked. If the display shows
- The
than six seconds.
the keyboard is locked. To unlock the keyboard press the key more
15
WIRING
MODELS RF-P
R heating element Ts safety cut out C three way selector
J5TsJ6
J4
PLACA
PCB
ELECTRONICA
dia
noche
3
4
0
C
sonda Tª
probe Tª
R
1
d
a
MODELS RF-F
R heating element Ts safety cut out
MODELS RF-E
R heating element Ts safety cut out C three way selector
Ts
R
Ts
entradasalida
PCB
PLACA
ELECTRONICA
probe Tª
sonda Tª
entrada
salida
PLACA
PCB
ELECTRONICA
selector
P
0
a
c
I
C
1
sonda Tª
probe Tª
3
R
16
NOTAS / NOTE / NOTAS
25
EN: WARNING: In order to avoid overheating do not cover the heater.
EN
The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. These instructions are only valid in the EU member states.
26
ELNUR S.A.
Travesía de Villa Esther, 11
28110, Algete - Madrid
Elnur UK - Unit 1
Brownstreet North,
Leigh, WN7 1BU
01942 6770119
www.elnur.es
www.elnur-global.com
www.elnur.co.uk
Como parte
Como parte da política de melhoria contínua do produto, Elnur s.a reserva a direita alterar especificações sem observação prévia.
de la política de mejora continua Elnur s.a. se reserva el derecho a realizar modificaciones técnicas sin previo aviso.
As a part of the policy of continuous product improvement Elnur s.a. reserves the right to alter specifications without notice.
30101012 R9
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use