www.elnec.com
Quick Guide
Device
Programmers
thank you for purchasing one of the ELNEC programmer
Introduction
This Quick Guide covers following ELNEC programmers, which interface with
the IBM PC compatible, portable or desktop personal computers. Programmers
allow you to directly connect to your PC through USB port or any standard
parallel (printer) (no special interface card needed).
Programmers are driven by an easy-to-use Windows control program with pulldown menu, hot keys and on-line help. Selection of device is performed by its
class, by manufacturer or simply by typing a fragment of vendor name and/or
part number. Standard device-related commands (read, blank check, program,
verify, erase) are boosted by some test functions and some special functions
(autoincrement – enables you to assign individual serial numbers to each
programmed device). All known data formats are supported. Automatic file
format detection and conversion is performed during loading of file.
It is important to remember, that in most cases, new devices require only a
software update.
Products configuration
BeeHive204
BeeProg2
BeeProg2C
SmartProg2
MEMprog2
programmer
USB cable
LPT cable - * - - -
ISP cable 4x
power cordset
internal power supply
external power supply - - 48 pins diagnostic POD – type I 1x
40 pins diagnostic POD – type I - - -
Diagnostic POD for ISP connectors #2 1x
ZIF anti-dust cover 4x
software CD
User manual
Quick Guide
brochure Notes about ESD
antistatic set
vacuum handling tool kit
sticker register your programmer
shipping case
* optional accessories
Before installing and using your programmer, check carefully that your package
includes all above mentioned parts.
• • • • • •
• • • • •
• • • •
• • • • •
• • •
• •
• •
• • • •
• • • • • •
• • •
• • • • • •
• • • • •
- -
•
- -
•
• • • • • •
• • • • • •
- - -
• • •
- - -
• •
- - -
- - -
SEEprog
-
•
-
-
-
-
-
Recommended PC requirements
2x
BeeHive204
BeeHive204
BeeProg2
BeeProg2C
SmartProg2
MEMprog2
OS - Windows Win 7 Win 7 Win 7 Win 7 Win 7 Win 7
CPU C2Quad C2D C2D C2D C2D C2D
RAM [MB] 2000 1000 1000 512 512 512
free disk space [MB] 2000 1000 1000 1000 1000 1000
USB 2.0 high speed
2x USB 2.0 high speed controllers
LPT IEEE1284 - -
These PC requirements are valid for 2.84/11.2011 version of PG4UW.
Free disk space requirement depends also on used IC device size and number of
attached programming sites. For large devices the required free space on disk will
• • • •
•
•
- -
SEEprog
-
•
be approximately 1000MB + 2x Device size x number of programming sites
attached to this PC.
Hardware setup
1. connect the USB (LPT) port of programmer to a USB (LPT) port of PC
using enclosed appropriate cable
2. connect the connector of the power supply adapter to the programmer
Software setup
Insert delivered CD to your CD drive and install program starts automatically.
Install program (setup.exe), which will guide you through the installation process
and which will undertake all the necessary steps before you can first run the
control program.
Run the control program
After start, control program PG4UW automatically scans all existing ports and
searches for any connected ELNEC programmer. Program PG4UW is common
for all the ELNEC's programmers, hence PG4UW will try to find all supported
programmers.
Menu File is used for source files manipulation, settings and viewing directory,
changes drives, changes start and finish address of buffer for loading and
saving files and loading and saving projects.
Menu Buffer is used for buffer manipulation, block operation, filling a part of
buffer with string, erasing, checksum and of course editing and viewing with
other items (find and replace string, printing...).
Menu Device is used for a work with selected programmable device: select,
read, blank check, program, verify, erase and setting of programming process,
serialization and associated file control.
Menu Programmer is used for work with programmer.
Menu Options is used to view and change various default settings.
Menu Help is used for view supported devices and programmers and
information about program version.
Double click on
Programming a device
1. select device: click on
2. load data into buffer:
a) from file: click on
b) from device: insert device to ZIF and click on
3. insert target device to ZIF
4. check, if the device is blank: click on
5. program device: click on
6. additional verify of device: click on
Free additional services:
• free technical support (phone/e-mail).
• free lifetime software update via our WEB site
• Keep-Current is a service by which ELNEC ships to you the latest version
of the control program for programmer and the updated user
documentation.
• AlgOR (Algorithm On Request) service allows you to receive from ELNEC
software support for programming devices not yet available in the current
device list.
www.elnec.com
Troubleshooting
We really want you to enjoy our product. Nevertheless, problems can occur. In
such cases, please, follow the instructions below.
• It might be your mistake in properly operating the programmer or its control
program PG4UW.
• Please read carefully all the enclosed documentation again. Probably
you will find the needed answer right away.
• Try to install programmer and PG4UW on another computer. If your
system works normally on the other computer you might have a
problem with the first PC. Compare differences between both
computers.
• Ask your in-house guru (every office has one!).
• Ask the person who already installed programmer.
• If the problem persists, please call the local dealer, from whom you
purchased the programmer, or call ELNEC direct.
If you want to contact us regarding defective programmer or problem with the
programmed device, please, use Problem report form. You can find it at
www.elnec.com, section Support.
More information
If you need more information, see please
• manual on the enclosed CD
• latest version of manual at
www.elnec.com
ZLI-0284F
Loading...