Elmo TND4004 User Manual

Page 1

DOME CAMERA

INSTRUCTION MANUAL

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

TND4004

CAUTION

· Do not use any power supply other than

specified.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

* The CAUTION label is attached on the back

of camera.

INFORMATION

This equipment has been tested and

found to comply with the limits for Class A

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference when the equipment

is operated in a commercial environment.

This equipment generates, use, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a

residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his

own expense.

USER-INSTALLER CAUTION:

Your

authority to operate this FCC verified

equipment could be voided if you make

changes or modifications not expressly

approved by the party responsible for

compliance to Part of the FCC Rules.

Page 2

- 1 -

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, install in accordance with the manufacture's instructions.

8. Do not install near heat sources such a radiators, heat registers, stoves or other apparatus (including

amplifiers) that produce heat.

9. Only use attachment/accessories specified by the manufacturer.

10. Unplug this apparatus during lighting storms or when unused for long periods of time.

11. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

been fallen onto the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

Page 3

- 2 -

1. Appearance view

2. Specifications

()

Unit : mm (inch)

Model

Power source

Power consumption

Pick-up device

Effective picture element

Scanning area

Scanning system

Scanning frequency

Sync. system

Resolution

S/N ratio

Standard illumination

AGC

Sens-up

White balance

Backlight control (BLC)

Iris level adjustment

VIDEO OUT terminal

Lens

Angle of view

Iris

Appearance color

Dimensions

Weight

Ambient temperature

Ambient humidity

TND4004

DC 12V (DC 11V-35V) or AC 24V (AC 15V-27V) 60Hz ± 0.5Hz

Approx. 3.5W

1/3" Color interline-transfer CCD

768 (H) X 494 (V)

4.88mm (H) X 3.66mm (V)

2:1 interlaced

LL : 15.75kHz (H), 60Hz (V) / INT : 15.734kHz (H), 59.94Hz (V)

Line-Lock/Internal (Factory-set at Line-Lock)

470TV lines (H), 350TV lines (V)

More than 48dB

150 lx (F1.4 under incandescent lamp)

Built-in

Provided (Factory-set at OFF)

ATW/AWC/manual/Preset (Factory-set at ATW)

Provided (Factory-set at OFF)

Provided (volume adjustment)

VBS 1V (p-p) 75Ω

F 1.4, f = 2.8 ~ 6mm

Horizontal : 47° (TELE) ~ 96° (WIDE)

Vertical : 36° (TELE) ~ 72° (WIDE)

Auto

Main body : White

Cover : Black

Diameter : 116mm (4.6") Height : 106mm (4.2") without protruded part

0.5 kg (1.1 lbs)

-10°C ~ +50°C (14°F~122°F)

30% ~ 90%

Note : Weight and dimensions are approximate.

Design and specifications are subject to change without prior notice.

106 (4.2)

SR53 (2.1)

SR56 (2.2)

Page 4

- 3 -

3. Name and Function of Each Part

Metal fitting

For mounting on the ceiling or wall.

Hook (3 locations)

For temporarily fixing the main body.

Main body

The main body of a camera section.

Dome cover

A protective cover for the lens section.

AC/DC power terminal

Connect this to the AC24V 60Hz or DC12V power supply.

VIDEO OUT terminal

Connect coaxial cable to a monitor TV, etc.

Ground terminal

Connect this to the ground wire of the power supply cord.

DC12V

AC24V

Page 5

- 4 -

Tilt lock screw

For locking the tilt after adjusting the image up/down direction.

Pan lock screw

For locking the pan after adjusting the image right/left direction.

Zoom ring

For adjusting the image size.

Focus ring

For adjusting the focus.

PUSH button

· Vertical sync. phase adjustment

To adjust the vertical sync. phase when using two or more Line-Lock cameras, press the PUSH button ( ) or ( ) until images stop rolling. However, it should be noted that this adjustment is not valid when the select switch is in such positions as WB1: L, WB2: L and WB3: H.

· Manual white balance selector

When the white balance selector is set to MANU (shift change) in on the next page, the white balance can be adjusted by using the PUSH button. This mode will prove effective under shooting conditions with little variation in color temperature.

* When the white balance selector is set to MANU (shift change), the vertical sync. phase can not be

adjusted.

ALC LEVEL

For adjusting the image brightness.

Main body mount screws (2 pcs)

Screws located for mounting the main body to the metal fitting.

Caution: Both screws must be tighten to prevent the camera from falling.

Reinforce board

A board rotating together with the camera part.

* This board may interfere with the selector switch depending on the set pan direction. Slide

the board to avoid the interference with the selector switch. After this sliding, be sure to

Page 6

- 5 -

4. Preset (MWB) Color temperature can be selected from among four different color temperatures.

b. INT/LL switch

· INT (internal) control switch

When the internal synchronization is used, set the switch to the INT side.

· LL (Line-Lock) control switch

Matching the vertical synchronization with the power frequency is called the line-lock. When two or more cameras are switched by the video switcher to a monitor TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching. Line-lock is operative only when the AC 24V power supply is connected.

Caution:

1. The camera is synchronized to the power frequency of 60Hz ± 0.5Hz covering a normal fluctuation of the power frequency. The camera may not compensate for large fluctuation caused by power generated by an engine generator. etc.

2. It takes about 10 seconds or more to obtain a stable synchronization after the power is turned on. This is necessary to stabilize the camera against the power noise.

3. When DC 12V power supply is used, set the switch to the INT side.

c. BLC (Back Light Control) switch

In case the back lighting is too bright to shoot the main object clearly, set this switch to ON position.

d. SENS-UP switch

To increase the sensitivity, set this switch to ON position.

Selector switch (details)

a. White balance selector

Combination of the switch 1, 2, and 3, the following adjustments are available:

1. ATW (AWB) The camera adjusts the white balance by automatically following the color temperature change within the pullin color temperature range. The pull-in color temperature range is from approx. 2500K to approx. 9500K.

2. AWC/HOLD (AWB)

AWC

This is auto white balance mode with no limits, such as pull-in frame.

HOLD

The white balance in the state can be held by switching the mode to HOLD after the white balance is attained by AWC.

This mode is effective for imaging conditions with little color temperature change.

3. Manual White Balance (MWB) The color temperature can be shifted by pressing the PUSH button. For the information of switch shift, refer to P. 4 .

(This figure shows the setting before shipment from our factory.)

WB1

L L L L H H H H

WB2

L H H L L L H H

WB3

L L H H L H L H

ATW AWC HOLD Manual Manual (Fixed 3200k) Manual (Fixed 4200k) Manual (Fixed 4700k) Manual (Fixed 6300k)

2 WB

BLC

INT

SENS UP

a. b. c. d.

OFF

Video output

Monitor TV

To DC 12V power supply

To AC 24V power supply

Video switcher

To AC 24V power supply

Video

input

Monitor TV

Page 7

- 6 -

Recommended mounting surface is wood or dry

wall.

(1) Make a round hole of 70mm OD (2.76") to the

mounting surface where the camera is to be

mounted. (Refer to Fig.1)

4-1 How to Install and Adjust

(2) Attach coaxial cable and power cord to the

POWER & VIDEO terminal on the metal

fitting. (Refer to Fig. 2)

Refer to Page 11 for preparation of the coaxial

cable.

4. How to Set Up

(Fig. 1)

(Fig. 2)

(3) Mark four mounting holes to the mounting

surface with pencil for the metal fitting as

follows:

1. Dimensions: Refer A or B from Fig. 3.

2. To mount on the ceiling, point mark on

the metal fitting toward the object. (Refer

to Fig. 3)

3. To mount on the wall, point the mark

on the metal fitting facing downward.

(Refer to Fig. 3)

Unit : mm (inch)

(Fig. 3)

Ceiling

Metal fitting

Ceiling mount screws

Coaxial cable

46 (1.81)

83.5 (3.29)

46 (1.81)

66.7 (2.63)

83.5 (3.29)

Power cables

(4) To mount on a wood surface, use four #8x

1.5" screws to secure the metal fitting.

To mount on a dry wall surface, drill four

3/16" holes first and insert 3/16" anchors then

secure the metal fitting with four #8x1.5"

screws.

All hardware is optional.

To directly mount on the surface, make

sure to use four screws to ensure firm

locking.

Be careful not to damage the coaxial or

power cables.

If it is impossible to make a 70mm hole to

the surface, use an optional metal fitting for

the wall (EB-413B).

Ax4

Bx4

mark

70mm (2.76")

Page 8

- 7 -

(6) Mount the body to the metal fitting.

Match the positioning mark on the main body

with the mark on the metal fitting, and

thrust the main body toward the metal fitting.

Be sure that the main body engages with the

hooks (3 locations) of the metal fitting (Fig. 5).

Confirm that the main body is in parallel with

the metal fitting when viewed from the side

(Fig. 6).

* If not, the camera

may come off from

the metal fitting and

drop.

(5) Remove the dome cover from the main body.

Remove the dome cover by turning it

counterclockwise (arrow direction) (Fig. 4).

(Fig. 4)

Hook

(Fig. 5)

Hook

Dome cover

Main body

Positioning mark

Metal fitting

mark

Bad example

Good example

(Fig. 6)

(7) Fasten the main body mount screws (2 pcs)

attached with the main body to lock the main

body on the metal fitting (Fig. 7).

* Confirm that notches and are

matched with the main body mount

screws. If not, loosen the pan lock screw,

turn the base, and match the notches

and with these screws.

If the notches are not matched with these

screws, a screwdriver cannot catch the

screws, and the body cannot be locked.

* Be sure to fasten the main body mount

screws.

Ceiling

Main body

(Fig. 7)

Main body mount screw

Base

Pan lock screw

Main body

Metal fitting

Driver

Page 9

- 8 -

(8) While watching the monitor, adjust the image

direction.

· Right/left direction (Fig. 8)

Loosen the pan lock screw, turn the base

right and left, and adjust the right/left

direction. After setting the right/left

direction, tightly fasten the pan lock screw.

* If the pan lock screw is not tightly

fastened, the base may turn when the

dome cover is mounted.

* Be careful not to drop the pan lock screw.

· Up/down direction

(Fig. 9)

Loosen the tilt lock screw, and adjust

up/down direction.

After setting the up/down direction, fasten

the tilt lock screw.

* Manually fasten the tilt lock screw.

If fastened with pliers or the like, the tilt

lock screw may be broken.

(Fig. 8)

(Fig. 9)

Tilt lock screw

Base

Pan lock screw

(9) Adjust the optical axis (Fig. 10).

Correct the tilt of the image with the optical

axis ring.

* Be sure to hold the optical axis ring when

making this correction.

(10) Adjust the angle of view with the zoom ring

(Fig. 11).

(Fig. 10)

(Fig. 11)

Optical axis ring

Zoom ring

50°

Page 10

- 9 -

(11) Adjust the focus with the focus ring (Fig. 12).

* Adjust the focus after adjusting the angle

of view.

(Fig. 12)

Focus ring

(12) Match the "I" mark on the lens with the

recessed portion of the camera holder

(Fig. 13).

* Be sure to match them, or the dome cover

may not be mounted in same lens

position.

(13) Mount the dome cover on the main body.

Match the mark on the dome cover with that

on the base, and turn the dome cover

clockwise (arrow direction) until it is clicked

(Fig. 14).

* If these marks are not matched, the dome

cover cannot be mounted.

(Fig. 13)

(Fig. 14)

Lens

Recessed part of the camera holder

Dome cover

Base

Main body

Mark

Page 11

- 10 -

4-2 How to Connect the Cables

(1) Prepare the coaxial cable end as shown

(Fig. 15).

(2) Connect the coaxial cable and power cables to

the terminal strip.

Insert the core underneath of the appropriate

locking washer fitting, and fasten the screw.

Secure the shielding wire to the coaxial cable

fixing metal fitting with the screws (Fig. 16).

* If you wish to run the coaxial cable

outside of the wall or ceiling, use

optional metal fittings for wall

(EB-413B).

(3) Connect cables to the monitor TV and power

source.

Unit : mm (inch)

(Fig. 15)

(Fig. 16)

Locking washer

Coaxial cable lock metal fitting

Core Shielding wire

4-3 Notes in Use

1. Use this unit indoors. Do not mount it outdoors.

2. When the cover needs cleaning, wipe it with a soft cloth.

Do not use alcohol, thinner or the like.

3. If a part of the image is exposed to strong light, such as light bulb, the auto iris may be activated to

darken the screen. In this case, change the direction or adjust the iris with the ALC adjust volume.

(0.31)

(0.20)

(0.47)

Power cables

Terminal strip

Page 12

- 11 -

PRECAUTIONS FOR USE AND INSTALLATION

* Never aim the camera at the sun.

Never aim or point the camera at the sun even if you are not shooting.

* Do not shoot intense light.

Strong light such as a spot light on the image plane will cause blooming or smear. When strong light comes into the image plane, vertical stripes may appear on it. However, this does not mean that the camera is defect.

* Take precautions when handling a camera.

Do not drop your camera, or give it a strong shook or vibration. This may cause camera to malfunction.

* Do not touch internal parts.

Be sure not to touch the internal parts. This may cause to electrical shock.

* Do not let the camera get wet.

Install the camera at the place where it will not get wet. Should it gets wet, turn off the power immediately and contact your dealer.

* Install your camera where no video noise appears.

When camera cables have been laid near electric wires or television receivers, a noise may interfere the image. If noise occurs, relocate cables or reinstall equipment.

* Check the ambient temperature and humidity.

Avoid using camera in areas where temperature is consistently hotter or colder than the specified range (See Specifications chart below) or poor image quality or damaged parts may occur. Precautions should also be taken to avoid areas of high humidity.

* Should you notice any trouble.

If any trouble occurs while you are using the camera, turn off the camera and contact your dealer. Failure to do so may cause damage to the camera.

* The socket-outlet should be installed near the

equipment and should be easily accessible.

* Do not place this video product on an unstable cart,

stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.

* This video product should be operated only from the type

of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your appliance dealer or local power company.

* Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, screws, and the point where they exit from the appliance.

* Do not overload power supply and extension cords, as

this can result in a risk of fire or electric shock.

* Never push objects of any kind into this video product

through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of kind on the video product.

* When replacement parts are required, be sure the service

technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards.

* Upon completion of any service or repairs to this video

product ask the service technician to perform safety checks to determine that video product is in proper operating condition.

6X1NSBA02 Printed in CHINA

ELMO (Europe) G.m.b.H.

Neanderstr. 18 40233 Dusseldorf, Germany Tel.

0211-376051-53 Fax. 0211-376630 E-mail:elmoeurope@AOL.com Web:http://www.elmo.de/

ELMO Mfg. Corp.

1478 Old Country Road, Plainview, NY 11803-5034 U.S.A. Tel.

516-501-1400 Fax. 516-501-0429 E-mail:elmo@elmousa.com Web:http://www.elmousa.com/

ELMO Canada Mfg. Corp.

44 West Drive, Brampton, Ontario, L6T 3T6, Canada Tel.

905-453-7880 Fax. 905-453-2391 E-mail:info@elmocanada.com Web:http://www.elmocanada.com/

ELMO CO., LTD.

6-14, Meizen-cho, Mizuho-ku, Nagoya, 467-8567 Japan

OVERSEAS SUBSIDIARY COMPANIES