Elmo SUV-CAM BWV Instruction Manual
111111
2
Introduction
IMPORTANT SAFEGUARDS
Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
Retain Instructions - The safety and operating instructions
should be retained for future reference.
Heed Warnings - All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions - All operating and use instructions
should be followed.
Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Attachments - Do not use attachments not recommended
by the product manufacturer.
Power Sources - This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home
consult your appliance dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Damage Requiring Service - Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the
product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation.
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance
- this indicates a need for service.
Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
WARNING: Handling the cord on this product or
cords associated with accessories sold with this
product, will expose you to lead, a chemical known to
the State of California to cause birth defects or other
reproductive harm.
Wash hands after handling.
Introduction (Continued)
3
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
The connection of a non- shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this device
and may cause interference levels which exceed the limits established by the
FCC for this equipment. It is the responsibility of the user to obtain and use a
shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused
interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
FOR UNITED STATES USERS:
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
USER-INSTALLER CAUTION:
Your authority to operate this FCC verified equipment could be voided if you make
changes or modifications not expressly approved by the party responsible for
compliance to Part 15 of the FCC rules.
Introduction (Continued)
4
Lithium-Ion Battery Handling Precautions
Danger
Do not disassemble or modify the battery pack. The battery pack is equipped with built-in safety protection features. Should these
features be disabled, the battery pack can leak acid, overheat, emit smoke, burst and/or ignite.
Do not connect the positive (+) and (-) terminals with a metal object such as wire. Do not transport or store the battery pack together
with metal objects such as necklaces, hair pins etc. Otherwise, short-circuiting will occur, over current will flow, causing the battery
pack to leak acid, overheat, emit smoke, burst and/or ignite, or the metal object such as wire, necklace or hair pin can generate heat.
Do not discard the battery pack into fire or heat it. Otherwise, its insulation can melt down, its gas release vent or safety features will
be damaged and/or its electrolyte can ignite, possibly leading to acid leakage, overheating, smoke emission, bursting and/or ignition.
Do not use or leave the battery pack near a heat source such as a fire or a heater (80°C or higher). If the resin separator should be
damaged owing to overheating, internal short-circuiting may occur to the battery pack, possibly leading to acid leakage, overheating,
smoke emission, bursting and/or ignition of the battery pack.
Do not immerse the battery pack in water or seawater, and do not allow it to get wet. Otherwise, the protective features in it can be
damaged, it can be charged with extremely high current and voltage, abnormal chemical reactions may occur in it, possibly leading
to acid leakage, overheating, smoke emission, bursting and/or ignition.
Do not recharge the battery pack in extremely hot weather. Otherwise, hot temperatures can trigger its built-in protective features,
inhibiting recharging, or can damage the built-in protective features, causing it to be charged with extremely high current and voltage,
and, as a result, abnormal chemical reactions can occur in it, possibly leading to acid leakage, overheating, smoke emission,
bursting and/or ignition.
Do not pierce the battery pack with a nail or other sharp objects, strike it with a hammer, or step on it. Otherwise, its battery pack will
became damaged and deformed, internal short-circuiting can occur, possibly leading to acid leakage, overheating, smoke emission,
bursting and/or ignition.
Do not strike or throw the battery pack. The might cause leakage, overheating, smoke emission, bursting and/or ignition. Also, if the
protective feature in it becomes damaged, it could become charged with an extremely high current and voltage, abnormal chemical
reactions can occur, which can lead acid leakage, overheating, smoke emission, bursting and/or ignition.
Introduction (Continued)
5
Do not use an apparently damaged or deformed battery pack by drop of the battery pack or any other damage. Otherwise, acid
leakage, overheating, smoke emission, bursting and/or ignition of the battery pack may occur.
Do not directly solder the battery pack. Otherwise, heat can melt down its insulation, damage its gas release vent or safety features
possibly leading to acid leakage, overheating, smoke emission, bursting and/or ignition.
Do not reverse the positive (+) and negative (-) terminals. Otherwise, during recharging, the battery pack will be reverse – charged,
abnormal chemical reactions then may occur, or excessively high current can flow during discharging possibly leading to acid
leakage, overheating, smoke emission, bursting and/or ignition.
Do not connect the battery pack to an electrical outlet, vehicle cigarette lighter, etc. When subjected to large voltage, over current can
flow on the battery pack, possibly leading to acid leakage, overheating, smoke emission, bursting and/or ignition.
Do not use the battery pack for a purpose other than those specified. Otherwise, its guaranteed performance will be lost and/or its
service life will be shortened. Depending on the equipment in which the battery pack is used, excessively high current can flow
through battery pack, possibly damaging it and leading to acid leakage, overheating, smoke emission, bursting and/or ignition.
Battery electrolytes can cause skin and eye injury. If you come into contact with any material leaking from the battery, it could be
electrolyte. Do not touch your face or eyes. Wash your hands or the area of contact with clean running water immediately. Seek
medical attention immediately if contact with the eyes has occurred.
Warning
If recharging operation fails to complete even when a specified recharging time has elapsed, immediately stop further recharging.
Otherwise, acid leakage, overheating, smoke emission, bursting and/or ignition can occur.
Do not put the battery pack into a microwave oven or pressurized container. Rapid heating or disrupted sealing can lead to acid
leakage, overheating, smoke emission, bursting and/or ignition.
If the battery pack leaks or gives off a bad odor, remove it from any exposed flame. Otherwise, the leaking electrolyte may catch fire,
and the battery pack may emit smoke, burst or ignite.
If the battery pack gives off an odor, generates heat, becomes discolored or deformed, or in any way appears abnormal during use,
recharging or storage, immediately remove it from the equipment or battery pack charger and stop using it. Otherwise, the
problematic battery pack can develop acid leakage, overheating, smoke, emission, bursting and/or ignition.
Introduction (Continued)
6
Caution
Do not use or subject the battery pack to intense sunlight or hot temperatures such as in a car in hot weather. Otherwise, acid
leakage, overheating and/or smoke emission can occur. Also, its guaranteed performance will be lose and/or its service life will be
shortened.
The battery pack incorporates built-in safety devices. Do not use it in a location where high levels of static electricity may be present.
Otherwise, the safety devices can be damaged, possibly leading to acid leakage, overheating, smoke emission, bursting and/or
ignition.
The guaranteed recharging temperature range is 0 to 45°C. A recharging operation outside this temperature range can lead to acid
leakage and/or overheating of the battery pack, and may cause damage to it.
If electrolyte leaking from the battery pack contacts your skin or clothing, immediately wash it away with running water. Otherwise,
eye injury or skin inflammation can occur.
Store the battery pack in a location where children cannot reach it. Also, make sure that sure that a child does not take out the battery
pack from the battery pack charger or equipment.
If you find rust, a bad odor, overheating and/or other irregularities when using the battery pack for the first time, return it your supplier
or vendor.
Introduction (Continued)
7
BEFORE YOU USE
Temperature of the main body
When this recorder is used for a long time in the power-on state, the temperature of the main body may become high. However, this
is not a fault.
The power plug cord applicable to the local power specifications is attached. Be sure to use power cord applicable to your local
power specification.
Use only the attached AC adapter. Do not use any other AC adapter on any account.
Use this recorder under the following environmental conditions:
Temperature: 0°C to 40°C (32°F to 104°F)
Humidity: -10 to 80% (No condensation)
Do not place this recorder at any of the following places:
A place exposed to direct sunlight, a humid or dusty place, a place exposed to sea wind
A place with an extreme temperature or humidity variation, such as near an air conditioner
A place near magnet or magnetic field
Note: The recorder and the AC adapter are not waterproof.
Camera cable (Optional)
Note: Pulling or dragging the camera cable when using the camera could cause failure to the recorder or the camera.
Note: If there is a break or hole in the camera cable coating this could cause water penetration through such break or hole and
resultant failure in the recorder or the camera.
Do not clean the recorder with volatile solvent, such as thinner and benzene; this could cause the recorder to fail. Clean this
recorder only with a dry, soft cloth.
Introduction (Continued)
8
Do not rub or hit the front or the LCD panel roughly, the front or the LCD panel could be damaged or broken.
Do not point the camera lens directly at the sun, or the camera may malfunction.
Protect the camera from strong impacts or vibration. It could cause troubles.
When removing the battery, turn OFF the power supply to the recorder beforehand.
When carrying the recorder, make sure to hold its body. Moving or carrying the recorder by holding the camera cable could result in
troubles.
This recorder is composed of precision electronic parts. If it is handled as follows, files saved in the SD card may be destroyed.
The battery or SD card is removed or the USB cable is connected while the recorder is in operation.
The USB cable or AC adaptor is disconnected during communication.
Any other abnormal operations
If this recorder is disassembled or altered intentionally by the user, the recorder will no longer be qualified for free repair even if it is
within the warranty period.
Introduction (Continued)
9
Battery
The battery used for this recorder is a rechargeable lithium-ion battery. This battery is susceptible to temperature and humidity, and
the higher or lower the humidity is, the more the battery is susceptible.
Whenever the use of this recorder ends, be sure to remove the battery.
Note: The shooting enabled time duration is shorter in cold climate, such as at a ski area.
If the battery is dropped by accident, check the terminal area for deformation. If the battery is set in this recorder with the terminal
area deformed, the recorder may be damaged.
Batteries must be disposed of as chemical waste. DO NOT INCINERATE AS BATTERY MAY EXPLODE
Be careful not to drop the battery pack when you release it from the Cam.
For a long-time storage, select a dry place with the temperature range of 15 – 25℃.
Be careful not to get the battery wet.
Clock
This recorder contains no clock battery. If the clock is not kept supplied with power from the battery or AC adapter, the date and time
settings will be reset. (ÎP28)
LCD panel
The LCD panel used for the LCD monitor has been made with ultra-high precision, has the effective pixel count of 99.99% or more.
However, note that some LCD panels may have the pixel missing and a continuous glow of 0.01% or less.
AC adapter
Even if the battery is not set in the system, this system can be used with the AC adapter alone.
When the AC adapter is used near a radio receiver (particularly when receiving medium wave), the radio receiver could have noise.
When using, keep the AC adapter at least 1m (3.3ft.) away from a radio receiver.
The AC adapter in use could emit oscillating sound from the inside. This is not an abnormal phenomenon.
After use, be sure to unplug the AC adapter from the AC power outlet or power will be continue to be consumed at up to 0.3W.
Be careful not to contaminate the terminal area of the AC adapter.
Introduction (Continued)
10
SD memory card
Do not leave the SD memory card in any place that is exposed to high temperature or direct sunlight or any source of
electromagnetic wares or static electricity. Also, do not bend, drop or strongly shock the SD memory card.
Otherwise, the SD memory card could be broken or the contents of the SD memory card could be destroyed or lost.
After use or for storage or carriage, put the SD memory card into a case or pouch.
Be careful not to allow the terminal area at the back of the SD memory card to be contaminated with dirt, water or foreign matter. Do
not the terminal area.
Image data
The recorded data could be destroyed or lost if you fail to handle the unit or the SD card according to the precautions noted above.
Under those circumstances, ELMO USA Corp will not liable in any way for any damages due to corruption of or loss of the recorded
data.
Do not use the product where video or audio recording is prohibited by law.
You may to be ordered to leave, have the product confiscated, be arrested and be subject to fines and prosecution.
Condensation
“Condensation” is the formation of small drops of water on the inside or outside of this recorder when steam in the air changes to
liquid when it is brought from a cold place suddenly into a warm place. If the recorder is used with condensation, the camera could
not take clear images or the recorder could be broken down.
Condensation tends to occur when
This recorder is brought from a ski slope into a heated place.
This recorder is brought from a cooled room or car compartment into a hot open air.
Measures to counter condensation
When this recorder has to be brought from a cold place suddenly into a warm place, place the recorder in a plastic bag and airtightly
seal the bag beforehand. Then, leave the recorder as it is in the warm place for about an hour, and then take it out when the recorder
is warmed up to the ambient temperature.
If condensation occurs
Turn OFF the power supply, and leave this recorder for about an hour until the condensation disappears. After confirming no
condensation, start using the recorder.
Note with care that if the recorder is used particularly with the condensation left on the inside of the camera lens, the recorder could
not record clear images.
Introduction (Continued)
11
Carrying
Do not sit down on a chair or the like with this recorder in the rear pocket of your trousers or skirt, or the recorder could be broken
down or damaged.
Don’t use the recorder where it is prohibited to take pictures. You may be ordered to leave, punished by laws, arrested or get
confiscated the recorder by the police.
Don’t use the recorder for purposes that could infringe with laws like the nuisance prohibition ordinance, for example. You may be
punished by laws, arrested or get confiscated the recorder by the police.
Introduction (Continued)
12
DISCLAIMERS
● The contents of this instruction manual are subject to change without notice.
● It is prohibited to copy any part or the whole of this instruction manual without our prior written consent. Unless used for personal
use, it is also prohibited under copyright law to use this instruction manual without our prior consent.
● For any claim for loss or lost earnings due to the use of this recorder or any claim raised by a third person or party, be forewarned
that we are not liable.
ELMO does not warrant this product for suitability for any specific purpose.
● ELMO USA Corp will not liable for: a) any claim for loss earnings due to the use of this recorder or any claim raised by a third person
or party, b) for any damage, lost earnings or the like caused by the loss of the memory contents due to failure, repair or other reason,
be forewarned that we are not liable at all.
Camera is not included in this product.
This product functions as recorder only; therefore please prepare a camera device to be used with this recorder.
It is not possible to use the camera head for SUV-CamⅡor SUV-Cam Professional with this recorder.
In the description of this manual, the notation is as follows:
- SD memory card, SDHC memory card Æ “SD card”
- Battery pack Æ “Battery”
Precautions for shooting
When shooting an important scene, be sure to try shooting beforehand and confirm normal video and audio recording operation.
Compensation related to the memory contents
ELMO USA Corp. will not be liable for compensation to the user if the visual record or audio record fails due to some problem with
this recorder or SD memory card.
Image of the SD memory card
The data recorded on this recorder may not be playable on some other recorders. Always confirm this compatibility beforehand.
The following images may not be playable on this recorder:
- Images recorded or created on other recorders
- Images edited on a PC
Introduction (Continued)
13
SD card applicable to this system
- For this system, the SD card formatted in the FAT16 form that complies with the SD Standard or in the FAT32 form that complies
with the SDHC Standard can be used.
- We do not guarantee functions when using SD card with a capacity of less than 1GB and more than 8GB.
- Format the SD card only with a Windows PC.
● The SD memory card formatted may not always be applicable based on the maker and the kind of the SD memory card for
this recorder.
● The free space of the SD memory card is smaller than the indicated capacity.
Normal operation confirmed SD cards (SDHC cards). Other SD cards may work but have not been tested by ELMO.
Manufacturer Model Capacity
SunDisk
SDSDB-2048-J60 2GB
SDSDBR-4096-J85 4GB
SDSDB-8192-J95 8GB
SDSDH-008G-J61 8GB
● SUV-Cam checking mode
Video recording mode :
Resolution [all], Recording mode [Video + Audio], Image quality [High], Recording speed [25 frames/sec]
Checking contents : Normal operation of recording and playing
※ The normal operation was checked with SUB-Cam.
However, we shall not guarantee the normal operation of the above SD cards themselves.
For the latest SD card support information, refer to the SUV-Cam website, http://www.elmo.co.jp/suv-cam/en/support/ .
Life of the battery
The battery has its own span of life. Along with the frequency of use and the time passed, the battery capacity decreases gradually.
When the usable time becomes substantially short, the battery life seems to have come near the end. Then, procure a new battery.
LCD monitor
Do not press the LCD monitor strongly, or the display of the LCD monitor could be uneven or the LCD monitor could be broken down.
When used in a cold place, images look like trailing. However, this is not a fault.
Images in this manual
The photos in this manual as display image examples are only imaginary. They are not images actually taken by using this recorder.
Introduction (Continued)
14
Copyright
Unless used for personal use, it is prohibited strictly under copyright law or international convention to use any still-image or
moving-image format file without the prior consent of the copyright holder. It is also prohibited strictly under copyright law or
international convention to transfer such a file, whether it is paid for or charge-free, onto the Internet or distribute the same to third
persons. If this recorder should be used for any illegal act against copyright law, be forewarned that we are not liable at all for any
compensation. Even if using for personal use, be careful that there could be a situation where video or audio recording is restricted or
illegal.
- ：The SD logo is a registered trademark.
- ：The SDHC logo is a registered trademark.
- Windows, Windows MediaTM, Internet Explorer and DirectX are trademarks of Microsoft Corporation of the United States and
other countries.
- Other names, company names and product names referred to in this instruction manual are trademarks or registered trademarks
of the respective companies.
This recorder may be use in household environment. However, if this recorder is used in close proximity to a radio receiver or
television receiver, poor reception could be caused. Handle the recorder in the proper manner in accordance with the instruction
manual.
15
Note
Introduction (Continued)
16
Contents
Introduction .......................................................................... 2
IMPORTANT SAFEGUARDS ....................................................... 2
Lithium-Ion Battery Handling Precautions ..................................... 4
BEFORE YOU USE...................................................................... 7
DISCLAIMERS ........................................................................... 12
Contents ..................................................................................... 16
Confirming the Accessories upon Unpacking .............................. 17
Preparations ............................................................................ 18
The Name of Each Part .............................................................. 18
The Name of Each Screen ......................................................... 19
How to Charge the Recorder ...................................................... 19
Remaining Battery Power ........................................................... 20
Connections to a camera device ................................................ 22
How to Load and Unload the SD Memory Card .......................... 24
Turn ON and Turn OFF the Power Supply ............................ 25
Turning ON the Power Supply .................................................... 25
Turning OFF the Power Supply .................................................. 26
Setting to the Hold State ........................................................ 27
Set the Date and Time ............................................................ 28
Recording ................................................................................ 29
How to Record ........................................................................... 29
Standard Duration of Recording ................................................. 31
Playing Back the File ............................................................. 35
How to Play the File ................................................................... 35
Search / Bookmark ..................................................................... 37
Changing the Play Settings ........................................................ 39
OSD item list of play settings ...................................................... 40
Using in Connection with External Devices ........................ 41
Attaching an External Microphone to the Recorder .................... 41
Outputting Video to the External Monitor .................................... 42
Connection to the Earphone....................................................... 43
Connection to a Speaker ............................................................ 43
Changing Various Settings on the Setting Item Screen ..... 44
How to Change .......................................................................... 44
Setting Item List ......................................................................... 45
Continuous Overwrite Recording ............................................... 48
SD Card Information .................................................................. 49
Firmware Upgrade ..................................................................... 50
USB Mode ................................................................................. 52
Setting the Date and Time .......................................................... 53
Beep Setup ................................................................................ 54
Password Setting ....................................................................... 55
Connection to the PC ............................................................. 56
Connection to the PC ................................................................. 56
Browsing the Files ...................................................................... 57
Troubleshooting ..................................................................... 58
Specifications ......................................................................... 63
Note ......................................................................................... 64
Introduction (Continued)
17
Confirming the Accessories upon Unpacking
AV cable
Recorder
AC adapter/ Power cord
Battery pack
USB cable
Earphone
18
Earphone / AV output
LED
Camera cable attaching
connector
Strap hole
LCD
Microphon
∨（Down）
REC
∧（Up）
MENU
ENTER
External microphone
POWER&HOLD
Preparations
The Name of Each Part
Recorder
USB terminal
Battery lock
SD card slot
DC-IN terminal
RESET
Preparations (Continued)
19
The Name of Each Screen
zWarning message display
Message Meaning
NO SD CARD! The SD memory card has not been
loaded or may not have been loaded
properly. (ÎP24)
SD CARD LOCKED The write switch of the SD memory
card is in “LOCK.”
SD CARD ERROR This SD memory card cannot be
used. Please format the SD card or
change to another SD card which
has been formatted.
Can not playback this file The file is corrupted and cannot be
played.
SD CARD FULL! The remaining capacity of the SD
memory card is very low.
INVALID SD CARD
A problem is found in the SD card.
This SD memory card cannot be
used.
Folder name
HOLD
AV cable connection
External microphone
Battery remaining power
SD memory card
Purple: SD memory card in
Black: No SD memory card
Record state
: Video + audio
: Video (No audio)
: Audio only
Play state
: Play state
: Pause state
Serial No.
Running Time
Vol ume
Record file name
Record mode
: Video + audio
: Video (No audio)
: Audio only
Recordable time
SD memory card remaining capacity
Running Time
Record state
:Record state
Preparations (Continued)
20
How to Charge the Recorder
1
Set in the battery.
Fit the catches of the battery in their mating slits in the recorder,
and push the battery in completely.
2
Start recharging.
Plug the DC plug of the AC adapter in the DC-IN terminal on
the side of the recorder, and plug the power plug in the AC
power outlet.
Battery
Fit catches in
DC plug
DC-IN terminal
To AC power receptacle
While charging, the
LED lights up orange.
Upon completing the
charge, the LED turns
green.
Check
Battery charging time and continuous operating time
Charging time Continuous play time
Continuous recording time
(Saving mode: ON)
Approx. 3 hours 30min Approx. 10 hours 30min Approx. 4 hours
※ Charging in a high-temperature or low-temperature
environment may require longer time
When plugging or unplugging the AC adapter, turn OFF
the power supply to the recorder beforehand.
Push
Loading...